Add a new vendor attribute QCA_WLAN_VENDOR_ATTR_DISCONNECT_IES
to configure disconnect IEs to the driver. Driver shall fill
these IEs in disassoc/deauth frame.
These IEs are expected to be considered only for the next
immediate disconnection (disassoc/deauth frame) originated by
the DUT, irrespective of the entity (user space/driver/firmware)
triggering the disconnection.
The host drivers are not expected to use the IEs set through
this interface for further disconnections after the first immediate
disconnection initiated post the configuration.
If the IEs are also updated through cfg80211 interface (after the
enhancement to cfg80211_disconnect), host driver is expected to
take the union of IEs from both of these interfaces and send in
further disassoc/deauth frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor sub command QCA_NL80211_VENDOR_SUBCMD_OEM_DATA
with attributes qca_wlan_vendor_attr_oem_data_params to support
OEM data. It is used to send OEM data binary blobs from
application/service to firmware. The attributes defined in enum
qca_wlan_vendor_attr_oem_data_params are used to deliver the
parameters.
Signed-off-by: Paul Zhang <paulz@codeaurora.org>
This reduces differences in timing and memory access within the
hunting-and-pecking loop for ECC groups that have a prime that is not
close to a power of two (e.g., Brainpool curves).
Signed-off-by: Jouni Malinen <j@w1.fi>
The driver automatically starts beacon reporting if it pauses the beacon
reporting for any reason other than disconnection. In specific cases,
userspace may not want the beacon reporting to be automatically resumed
after a pause. Add interface support for userspace to specify driver not
to start beacon reporting automatically after a pause.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the following vendor attributes under the enum
qca_wlan_vendor_attr_spectral_scan to support the configuration of
Spectral DMA debug.
1. QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_RING_DEBUG
Enable/disable debug of the Spectral DMA ring
2. QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_BUFFER_DEBUG
Enable/disable debug of the Spectral DMA buffers
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a config option to allow setting a custom Basic NSS/MCS set. As a
default we use single stream HE-MCS 0-7.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Process HE information in (Re)Association Request frames and add HE
elements into (Re)Association Response frames when HE is enabled in the
BSS.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The HE Capibilities element has dynamic size due to the variable length
and optional fields at the end. Mask out the channel width capabilities
that are less than the configured. Only add the MCS/NSS sets for the
announced channel widths and also add the PPET elements.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
oper_chwidth is used for both VHT and HE here.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The bandwidth values are shared between VHT and HE mode so remove the
VHT specific prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The bootstrapping URI format for DPP was extended during protocol design
to allow a list of channels without having to repeat the same operating
class information for each channel. That change was not included in the
initial implementation of the parser and a channel-list like
"C:81/1,6,11" would not be understood correctly (i.e., only the longer
"C:81/1,81/6,81/11" form would have been parsed correctly).
Fix this by extending the parser to accept both the shorter and longer
form for a list of channels within a single operating class.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not allow auth->own_protocol_key to be overridden without having
freed the previously stored key in case a test sequence in
dpp_proto_auth_conf_replaced_by_resp is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not allow auth->peer_protocol_key to be overridden without having
freed the previously stored key in case two Authentication Response
messages are received.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The result of EC_GROUP_dup() needs to be freed, so do so within the
derivation functions for all error cases and in the callers for success
cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is mostly a theoretical case, but since crypto_bignum_rand() could
fail, need to free the allocated struct crypto_bignum *tmp in such a
case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
EC_GROUP_new_by_curve_name() allocates memory for the returned pointer,
so need to free this with EC_GROUP_free() before leaving the calling
functions. This was leaking memory when parsing JWK and when performing
PKEX.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
In practice, some APs have interop issues with the DUT. This sub command
is used to transfer the AP info between the driver and user space. This
works both as a command and event. As a command, it configures the
stored list of APs from user space to firmware; as an event, it
indicates the AP info detected by the firmware to user space for
persistent storage. The attributes defined in enum
qca_vendor_attr_interop_issues_ap are used to deliver the parameters.
Signed-off-by: Paul Zhang <paulz@codeaurora.org>
Update enum qca_wlan_vendor_attr_get_wifi_info to add support for
attribute QCA_WLAN_VENDOR_ATTR_WIFI_INFO_RADIO_INDEX. In addition
update the documentation for qca_wlan_vendor_attr_get_wifi_info and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO to fully describe the
operation of the command and the format of the attributes.
Signed-off-by: Jeff Johnson <jjohnson@codeaurora.org>
Add a QCA vendor sub command QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING
to implement beacon reporting feature. Different operations required to
implement this feature can be specified in
QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE.
Userspace requests the driver/firmware to periodically report received
Beacon frames whose BSSID matches the current connected BSS's MAC
address. If userspace requests the driver/firmware to send beacon
reports actively, the driver encapsulates the details of the beacon in
an event and sends it to userspace asynchronously. Otherwise, the driver
will only update the beacon in cfg80211 scan cache but will not send any
event to userspace.
If this command is not issued, the current behavior of the
driver/firmware is to update the cfg80211 scan cache only when there is
a scan issued by the host in progress or whenever there is a change in
IEs of the Beacon frames from the current connected BSS.
The userspace requests the driver/firmware to stop reporting beacons
when reporting is not required anymore. If the driver/firmware is not
able to receive Beacon frames because of other Wi-Fi operations such as
off-channel activities, etc., the driver/firmware sends a pause event to
userspace and stops reporting Beacon frames. The driver/firmware
indicates whether the beacon reporting automatically resumes later by
using the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES flag. If
userspace doesn't want the beacon reporting to be resumed automatically,
userspace can send QCA_WLAN_VENDOR_BEACON_REPORTING_OP_STOP command to
the driver to stop beacon reporting.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
There is no point in checking this pointer against NULL after it has
been dereferenced. Move the check to the beginning of the function.
Signed-off-by: Jouni Malinen <j@w1.fi>
The first four octets of the element were used as a host byte order u32.
That is not correct on bigendian CPUs, so handle byte swapping needs
properly. Mark the he_oper_params field as le32 to explicitly indicate
the byte order and swap the generated params content based on CPU byte
order.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Start sharing common SAE and EAP-pwd functionality by adding a new
source code file that can be included into both. This first step is
bringing in a shared function to check whether a group is suitable.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Move the identical function used by both SAE and EAP-pwd to
src/utils/common.c to avoid duplicated implementation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This reduces timing and memory access pattern differences for an
operation that could depend on the used password.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
SPR allows us to detect OBSS overlaps and allows us to do adaptive CCA
thresholds. For this to work the AP needs to broadcast the element
first.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
According to P802.11ax/D4.0 9.4.2.238 (HE Operation element) the BSS
Color Information field is located after the HE Operation Parameters
field. Fix the ordering of the bit masks/offsets for fields in these 3+1
octets used as a single 32-bit value. With these changes, Wireshark 3.2
is able to properly parse and display Beacon frames.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
This makes it easier to upper layer components to manage operating
channels in cases where the same radio is shared for both station and AP
mode virtual interfaces.
Signed-off-by: Omer Dagan <omer.dagan@tandemg.com>
Logs involving IEEE 802.11 Status Codes output the Status Code value,
but do not provide any explanation of what the value means. This change
provides a terse explanation of each status code using the latter part
of the Status Code #define names.
Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
Logs involving IEEE 802.11 Reason Codes output the Reason Code value,
but do not provide any explanation of what the value means. This change
provides a terse explanation of each Reason Code using the latter part
of the reason code #define names.
Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
Add initial implementation of DPP-over-TCP. This adds the general TCP
encapsulation routines into the shared src/common/dpp.c implementation.
That functionality will be exposed through hostapd and wpa_supplicant in
the following commits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This can be helpful for testing DPP2 Controller functionality (get
pkhash from Controller to Relay).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This can be used to provide configurable parameter to the global DPP
context. This initial commit introduces the msg_ctx context pointer for
wpa_msg().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update the version number for the build and also add the ChangeLog
entries for both hostapd and wpa_supplicant to describe main changes
between v2.7 and v2.8.
Signed-off-by: Jouni Malinen <j@w1.fi>
Explicitly verify that own and peer commit scalar/element are available
when trying to check SAE confirm message. It could have been possible to
hit a NULL pointer dereference if the peer element could not have been
parsed. (CVE-2019-9496)
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Try to avoid showing externally visible timing or memory access
differences regardless of whether the derived pwd-value is smaller than
the group prime.
This is related to CVE-2019-9494.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is an initial step towards making the FFC case use strictly
constant time operations similarly to the ECC case.
sae_test_pwd_seed_ffc() does not yet have constant time behavior,
though.
This is related to CVE-2019-9494.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These groups have significant probability of coming up with pwd-value
that is equal or greater than the prime and as such, need for going
through the PWE derivation loop multiple times. This can result in
sufficient timing different to allow an external observer to determine
how many rounds are needed and that can leak information about the used
password.
Force at least 40 loop rounds for these MODP groups similarly to the ECC
group design to mask timing. This behavior is not described in IEEE Std
802.11-2016 for SAE, but it does not result in different values (i.e.,
only different timing), so such implementation specific countermeasures
can be done without breaking interoperability with other implementation.
Note: These MODP groups 22, 23, and 24 are not considered sufficiently
strong to be used with SAE (or more or less anything else). As such,
they should never be enabled in runtime configuration for any production
use cases. These changes to introduce additional protection to mask
timing is only for completeness of implementation and not an indication
that these groups should be used.
This is related to CVE-2019-9494.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make the non-failure path in the function proceed without branches based
on r_odd and in constant time to minimize risk of observable differences
in timing or cache use. (CVE-2019-9494)
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The QR test result can provide information about the password to an
attacker, so try to minimize differences in how the
sae_test_pwd_seed_ecc() result is used. (CVE-2019-9494)
Use heap memory for the dummy password to allow the same password length
to be used even with long passwords.
Use constant time selection functions to track the real vs. dummy
variables so that the exact same operations can be performed for both QR
test results.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Inclusion of common/dpp.h into hostapd/main.c brought in an undesired
unconditional dependency on OpenSSL header files even for builds where
DPP is not enabled. Fix this by making the dpp.h contents, and in
particular the inclusion of openssl/x509.h, conditional on CONFIG_DPP.
Fixes: 87d8435cf9 ("DPP: Common configurator/bootstrapping data management")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The rules defining which DH groups are suitable for SAE use were
accepted into IEEE 802.11 REVmd based on this document:
https://mentor.ieee.org/802.11/dcn/19/11-19-0387-02-000m-addressing-some-sae-comments.docx
Enforce those rules in production builds of wpa_supplicant and hostapd.
CONFIG_TESTING_OPTIONS=y builds can still be used to select any o the
implemented groups to maintain testing coverage.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit introduces an attribute
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REASON to carry the roam reason code
through QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Avoid duplicated code in each user of dpp_build_conf_req() by moving the
common encapsulation case into this helper function.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Merge the practically copy-pasted implementations in wpa_supplicant and
hostapd into a single shared implementation in dpp.c for managing
configurator and boostrapping information. This avoid unnecessary code
duplication and provides a convenient location for adding new global DPP
data.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The offset update for copying KEK2 from the extended PTK was overriding
the offset instead of incrementing it (a likely copy-paste error from
the first offset assignment based on KCK). This resulted in KEK2 being
set to incorrect segment of PTK. Fix this by updating the offset
properly so that KEK2 is copied from the correct place at the end of the
PTK.
Fixes: 2f37387812 ("FILS: Add more complete support for FT-FILS use cases")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use Diffie-Hellman key exchange to derivate additional material for
PMK-to-PTK derivation to get PFS. The Diffie-Hellman Parameter element
(defined in OWE RFC 8110) is used in association frames to exchange the
DH public keys. For backwards compatibility, ignore missing
request/response DH parameter and fall back to no PFS in such cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
DPP allows Diffie-Hellman exchange to be used for PFS in PTK derivation.
This requires an additional Z.x (x coordinate of the DH shared secret)
to be passed to wpa_pmk_to_ptk(). This commit adds that to the function
and updates all the callers to pass NULL,0 for that part in preparation
of the DPP specific changes to start using this.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows devices supporting DPP protocol version 2 or newer to
provision networks that enable both the legacy (PSK/SAE) and DPP
credentials.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Share a single parsing implementation for both hostapd and
wpa_supplicant to avoid code duplication. In addition, clean up the
implementation to be more easily extensible.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use this new message from Enrollee to Configurator to indicate result of
the config object provisioning if both devices support protocol version
2 or newer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Send out the new Protocol Version attribute in Authentication
Request/Response messages and determine the peer version based on this
attribute.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This subcommand is used to update Zigbee state and specified WLAN
durations to enhance success ratio of Zigbee joining network. The
attributes defined in enum qca_mpta_helper_vendor_attr are used to
deliver these parameters to the driver.
Signed-off-by: stonez <stonez@codeaurora.org>
Peer rate statistics is per-peer cached data in the driver. These
statistics needs to be flushed to a user space application on
synchronous/asynchronous events. This command is used as an event from
the driver to flush per-peer cached statistics to the application.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new QCA vendor specific feature capability indication for the
device to indicate the support of TWT.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The current/default behavior of set blacklist BSSID QCA vendor command
is a mandate to the driver - do not consider this BSSID for connect/roam
till reset.
There are use cases where this need not be a mandate and thus could
provide the flexibility for the driver to consider this BSSID if there
are no better ones. Such use cases can use this new flag attribute to
only hint the blacklist of a BSSID to the driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not start SAE authentication from scratch when the AP requests
anti-clogging token to be used. Instead, use the previously generated
PWE as-is if the retry is for the same AP and the same group. This saves
unnecessary processing on the station side in case the AP is under heavy
SAE authentiation load.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
According to IEEE Std 802.11-2016, 9.4.2.25 when fields of an RSNE are
not included, the default values are used. The cipher suite defaults
were hardcoded to CCMP in the previous implementation, but the default
is actually different for DMG: GCMP (per 9.4.2.25.2).
It is not possible to find out from the RSNE if the network is non-DMG
or DMG, so callers of wpa_parse_wpa_ie_rsn() need to handle this case
based on context, which can be different for each caller.
In order to fix this issue, add flags to the wpa_ie_data indicating
whether pairwise/group ciphers were included in the RSNE. Callers can
check these flags and fill in the appropriate ciphers. The
wpa_parse_wpa_ie_rsn() function still initializes the ciphers to CCMP by
default so existing callers will not break. This change also fixes some
callers which need to handle the DMG network case.
Signed-off-by: Lior David <liord@codeaurora.org>
This new QCA vendor attribute adds provision to specify the
ethernet protocol id from userspace to the packets which are
offloaded to the driver/firmware (e.g., IPv4, IPv6).
Signed-off-by: Arun Kumar Khandavalli <akhandav@codeaurora.org>
The new sae_password parameter [|vlanid=<VLAN ID>] can now be used to
assign stations to a specific VLAN based on which SAE Password
Identifier they use. This is similar to the WPA2-Enterprise case where
the RADIUS server can assign stations to different VLANs and the
WPA2-Personal case where vlanid parameter in wpa_psk_file is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow user space applications to check whether wlan firmware is alive
through an nl80211 vendor command.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The change is bigger because here we need to catch the error
condition if the last element doesn't fit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rather than always iterating elements from frames with pure
u8 pointers, add a type "struct element" that encapsulates
the id/datalen/data format of them.
Then, add the element iteration macros
* for_each_element
* for_each_element_id
* for_each_element_extid
which take, as their first 'argument', such a structure and
iterate through a given u8 array interpreting it as elements.
While at it also add
* for_each_subelement
* for_each_subelement_id
* for_each_subelement_extid
which instead of taking data/length just take an outer element
and use its data/datalen.
Also add for_each_element_completed() to determine if any of
the loops above completed, i.e., it was able to parse all of
the elements successfully and no data remained.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not use a separate enum for MBO WNM-Notification Request frame
subtype values since these share the same number space with the Hotspot
2.0 ones.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previously used value 2 was already assigned for another purpose
(MBO non-preferred channel report), so the newer T&C Acceptable
definition needs to be updated with a unique value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This new QCA vendor attribute indicates the EVM value in netlink.
Signed-off-by: stonez <stonez@codeaurora.org>
:100644 100644 ad5dac2... ede4fc8... M src/common/qca-vendor.h
The vendor command QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY was defined
to carry the list of avoid frequencies that aim to avoid any
interference with other coexistencies. This recommendation was followed
strictly by trying to prevent WLAN traffic on the impacted channels.
This commit refines the expectation of the interface by defining this
avoid channel list to allow minimal traffic but not heavier one. For
example, P2P may still be able to use avoid list frequencies for P2P
discovery and GO negotiation if the actual group can be set up on a not
impact channel.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support for configuring parameters for the MU EDCA Parameter Set
element per IEEE P802.11ax/D3.0.
Signed-off-by: Siva Mullati <siva.mullati@intel.com>
Define QCA vendor command attributes to configure HE +HTC support and
HE operating mode control transmission. This is used to configure the
testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These are not allowed in ISO C++ (and well, not really in ISO C either,
but that does not result in compiler warning without pedantic
compilation).
Since ieee802_11_common.h may end up getting pulled into C++ code for
some external interfaces, it is more convenient to keep it free of these
cases. Pull in ieee802_11_defs.h to get enum phy_type defined and move
enum chan_width to common/defs.h (which was already pulled in into
src/drivers/driver.h and src/common/ieee802_11_common.h).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
While the AP is configured to enable both FT-PSK and WPA-PSK, an HP
printer request both AKMs (copied from AP?) in Association Request
frame, but don't add MDIE and don't use FT. This results in the
connection failing.
Next in logs we see:
RSN: Trying to use FT, but MDIE not included
IE - hexdump(len=26): 30 18 01 00 00 0f ac 04 01 00 00 0f ac 04
02 00 00 0f ac 02 00 0f ac 04 00 00
This is seen with some HP and Epson printers. Work around this by
stripping FT AKM(s) when MDE is not present and there is still a non-FT
AKM available.
Signed-off-by: Janusz Dziedzic <janusz@plumewifi.com>
The Android-specific chmod and chown operations on the client socket
(for communication with wpa_supplicant) did not protect against file
replacement between the bind() and chmod()/chown() calls. If the
directory in which the client socket is created (depends a bit on the
version and platform, but /data/misc/wifi/sockets is commonly used)
allows write access to processes that are different (less privileged)
compared to the process calling wpa_ctrl_open2(), it might be possible
to delete the socket file and replace it with something else (mainly, a
symlink) before the chmod/chown operations occur. This could have
resulted in the owner or permissions of the target of that symlink being
modified.
In general, it would be safest to use a directory which has more limited
write privileges (/data/misc/wifi/sockets normally has 'wifi' group
(AID_WIFI) with write access), but if that cannot be easily changed due
to other constraints, it is better to make wpa_ctrl_open2() less likely
to enable this type of race condition between the operations.
Replace chown() with lchown() (i.e., a version that does not dereference
symlinks) and chmod() with fchmod() on the socket before the bind() call
which is also not going to dereference a symlink (whereas chmod()
would). lchown() is a standard operation, but the fchmod() on the socket
is less so (unspecified behavior in some systems). However, it seems to
work on Linux and in particular, on Android, where this code is
executed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds checks to common code to verify supported bandwidth options
for each channel using nl80211-provided info. No support of additional
modes is added, just additional checks. Such checks are needed because
driver/hardware can declare more strict limitations than declared in the
IEEE 802.11 standard. Without this patch hostapd might select
unsupported channel and that will fail because Linux kernel does check
channel bandwidth limitations.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
The new ieee802_11_ext_capab() and wpa_bss_ext_capab() functions can be
used to check whether a specific extended capability bit is set instead
of having to implement bit parsing separately for each need.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE P802.11-REVmd/D2.0, 9.4.2.20.7 (Beacon request) and 9.4.2.21.7
(Beacon report) add the Last Beacon Report Indication subelement to
Beacon Request and Beacon Report elements.
Add the Last Beacon Report Indication subelement to all Beacon Report
elements if the Beacon Request indicated that this subelement is
requested.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When the frame body subelement would cause the measurement report
element to exceed the maximum element size, the frame body subelement
used to be truncated. In addition, some elements were always truncated
in order to keep the reported frame body short (e.g. RSN IE).
Alternatively, IEEE P802.11-REVmd/D2.0, 9.4.2.21.7 extension to Beacon
reporting can be used: The frame body subelement is fragmented across
multiple beacon report elements, and the reported frame body fragment ID
subelement is added.
Use beacon report fragmentation instead of truncating the frame body
as this method gives the AP a more complete information about the
reported APs.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
In 2013 or so, IFNAME=foo was prepended to at least the Unix socket
communication from wpa_supplicant to wpa_cli. This broke the (fragile)
logic that made ping/pong work more often when wpa_supplicant is busy
sending logging info to wpa_cli.
Adding check for IFNAME=foo makes this work better.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Legacy ioctl() through SIOCDEVPRIVATE are deprecated. Follow the
approach taken by bridge-utils and make use of new bridge ioctl's
whenever possible.
For example, using legacy ioctl() breaks dynamic VLAN mode on 32-bit
Linux systems running 64-bit kernels.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
An AP might refuse to connect a STA if it has a low RSSI. In such case,
the AP informs the STA with the desired RSSI delta and a retry timeout.
Any subsequent association attempt with that AP (BSS) should be avoided,
unless the RSSI level improved by the desired delta or the timeout has
expired.
Defined in Wi-Fi Alliance Optimized Connectivity Experience technical
specification v1.0, section 3.14 (RSSI-based association rejection
information).
Signed-off-by: Beni Lev <beni.lev@intel.com>
This new QCA vendor command is used to query the supported AKM suite
selectors from the driver. There has been no such capability indication
from the driver and thus the current user space has to assume the driver
to support all the AKMs. This may be the case with some drivers (e.g.,
mac80211-based ones) but there are cfg80211-based drivers that implement
SME and have constraints on which AKMs can be supported (e.g., such
drivers may need an update to support SAE AKM using
NL80211_CMD_EXTERNAL_AUTH). Allow such drivers to specify the exact set
of supported AKMs so that user space tools can determine what network
profile options should be allowed to be configured. This command returns
the list of supported AKM suite selectors in the attribute
NL80211_ATTR_AKM_SUITES.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Looks like LibreSSL 2.8 pulled in the OpenSSL API change to mark the
first argument to X509_ALGOR_get0() const.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The purpose of Multi-AP specification is to enable inter-operability
across Wi-Fi access points (APs) from different vendors.
This patch introduces one new configuration parameter 'multi_ap' to
enable Multi-AP functionality and to configure the BSS as a backhaul
and/or fronthaul BSS.
Advertise vendor specific Multi-AP capabilities in (Re)Association
Response frame, if Multi-AP functionality is enabled through the
configuration parameter.
A backhaul AP must support receiving both 3addr and 4addr frames from a
backhaul STA, so create a VLAN for it just like is done for WDS, i.e.,
by calling hostapd_set_wds_sta(). Since Multi-AP requires WPA2 (never
WEP), we can safely call hostapd_set_wds_encryption() as well and we can
reuse the entire WDS condition.
To parse the Multi-AP Extension subelement, we use get_ie(): even though
that function is meant for parsing IEs, it works for subelements.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Include an OCI element in SA Query Request and Response frames if OCV
has been negotiated.
On Linux, a kernel patch is needed to let clients correctly handle SA
Query Requests that contain an OCI element. Without this patch, the
kernel will reply to the SA Query Request itself, without verifying the
included OCI. Additionally, the SA Query Response sent by the kernel
will not include an OCI element. The correct operation of the AP does
not require a kernel patch.
Without the corresponding kernel patch, SA Query Requests sent by the
client are still valid, meaning they do include an OCI element.
Note that an AP does not require any kernel patches. In other words, SA
Query frames sent and received by the AP are properly handled, even
without a kernel patch.
As a result, the kernel patch is only required to make the client properly
process and respond to a SA Query Request from the AP. Without this
patch, the client will send a SA Query Response without an OCI element,
causing the AP to silently ignore the response and eventually disconnect
the client from the network if OCV has been negotiated to be used.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
ocv_verify_tx_params() verifies that the receive OCI element includes
field values that are compatible with the local channel configuration.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This adds two utility functions to convert both operating classes and
and the chan_width enum to an integer representing the channel
bandwidth. This can then be used to compare bandwidth parameters in an
uniform manner.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This function can be used to easily convert the parameters returned
by the channel_info driver API, into their corresponding operating
class and channel number.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Also add the ChangeLog entries for both hostapd and wpa_supplicant to
describe main changes between v2.6 and v2.7.
Signed-off-by: Jouni Malinen <j@w1.fi>
The reverse case (local identifier configured but no identifier
received) was already covered, but PKEX is not going to complete
successfully if there is any difference in identifier configuration, so
ignore this other case as well. This avoids unnecessary responses to
PKEX requests with identifier from a device that is ready for PKEX in
general, but not for that particular request.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit enhances QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES to
also be an event, aimed to notify the link status (EX: connected
stations status on an AP link).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
A local memory allocation failuring during GAS Comeback Response frame
generation could result in freeing the response context without removing
it from the list. This would result in dereferencing freed memory when
processing the next comeback request.
Signed-off-by: Jouni Malinen <j@w1.fi>
If local memory allocation for the GAS response failed, couple of error
paths ended up leaking some memory maintaining the state for the
exchange. Fix that by freeing the context properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Parse the OSEN IE from the AP to determine values used in the AssocReq
instead of using hardcoded cipher suites. This is needed to be able to
set the group cipher based on AP advertisement now that two possible
options exists for this (GTK_NOT_USED in separate OSEN BSS; CCMP or
GTK_NOT_USED in shared BSS case). Furthermore, this is a step towards
allowing other ciphers than CCMP to be used with OSEN.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG vendor command
to set the priorities among different types of traffic of
WLAN/BT/Zigbee during coex scenarios.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add interface for drivers to report changes in TX/RX throughput
dynamically to user space. This information can be used by userspace
tools to tune kernel's TCP parameters in order to achieve peak
throughput. The driver may optionally provide guidance on which TCP
parameters to be configured for optimal performance along with the
values to be configured.
The TCP parameters that need to be tuned for peak performance are not
interface specific. Based on the guidance from the driver and
considering the other interfaces that may be affected with the new
configurations, a userspace tool has to choose the values to be
configured for these parameters to achieve optimal performance across
interfaces.
The throughput levels informed by the driver with this event are only
for providing guidance on TCP parameter tuning from userspace. The
driver may change the thresholds used to decide low or medium or high
throughput levels based on several parameters based on the PHY layer
capacity in the current connection, the number of packets being
dispatched per second, or the number of packets pending in queues, etc.
The throughput levels may not be consistent with the actual throughput
of the link.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure action
frame transmission in HE trigger based PPDU.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure HE
single user PPDU transmission.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attributes to configure HE
operating mode control field bandwidth, number of spatial streams, and
UL MU disable configuration. Define a new attribute to clear the
previously set HE OM control field configuration. This is used for
testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support for negotiating WNM Collocated Interference Reporting. This
allows hostapd to request associated STAs to report their collocated
interference information and wpa_supplicant to process such request and
reporting. The actual values (Collocated Interference Report Elements)
are out of scope of hostapd and wpa_supplicant, i.e., external
components are expected to generated and process these.
For hostapd/AP, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration. STAs are requested to perform
reporting with "COLOC_INTF_REQ <addr> <Automatic Report Enabled> <Report
Timeout>" control interface command. The received reports are indicated
as control interface events "COLOC-INTF-REPORT <addr> <dialog token>
<hexdump of report elements>".
For wpa_supplicant/STA, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration and setting Collocated
Interference Report Elements as a hexdump with "SET coloc_intf_elems
<hexdump>" control interface command. The hexdump can contain one or
more Collocated Interference Report Elements (each including the
information element header). For additional testing purposes, received
requests are reported with "COLOC-INTF-REQ <dialog token> <automatic
report enabled> <report timeout>" control interface events and
unsolicited reports can be sent with "COLOC_INTF_REPORT <hexdump>".
This commit adds support for reporting changes in the collocated
interference (Automatic Report Enabled == 1 and partial 3), but not for
periodic reports (2 and other part of 3).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add NAN NDP attribute QCA_WLAN_VENDOR_ATTR_PEER_NDPE_SUPPORT which
indicates if NDP remote peer supports NDPE attribute or not.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a subcommand for Channel Frequency Response (CFG) Capture
Configuration and define attributes for configuring CFR capture
parameters per peer and enabling/disabling CFR capture.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend hostapd to allow the new OSU Provider NAI List ANQP-element to be
advertised in addition to the previously used OSU Providers list
ANQP-element. The new osu_nai2 configurator parameter option is used to
specify the OSU_NAI value for the shared BSS (Single SSID) case while
osu_nai remains to be used for the separate OSU BSS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Driver/firmware does roam scan when it finds the need to roam to a
different BSS. Add a QCA vendor event to indicate such roam scan events
from driver/firmware to user space.
Please note that some drivers may not send these events in few cases,
e.g., if the host processor is sleeping when this event is generated in
firmware to avoid undesired wakeups.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The temporary EC_POINT 'sum' needs to be freed at the end of the
function with the other OpenSSL allocations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It looks like at least OpenSSL 1.1.0i includes the extra checks in
EC_POINT_set_affine_coordinates_GFp() that break the previously used
mechanism for generating invalid keys. Fix this by using the alternative
design that was used with OpenSSL 1.1.1 and BoringSSL.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Parse the Venue URL ANQP-element payload and report it with the new
RX-VENUE-URL event messages if the query was done using PMF.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new QCA vendor specific test config attribute to configure the
support for receiving the MPDU with operating mode control subfield.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This enhances DPP_AUTH_INIT, DPP_CONFIGURATOR_SIGN, and SET
dpp_configurator_params to allow optional setting of the DPP groupId
string for a Connector. If the value is not set, the previously wildcard
value ("*") is used by default.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The payload used for the existing NAN vendor command,
QCA_NL80211_VENDOR_SUBCMD_NAN is a binary blob of data. This
command is not extendable to send additional information. Hence
define a new vendor command QCA_NL80211_VENDOR_SUBCMD_NAN_EXT,
that can carry the binary blob encapsulated within an attribute
and can carry additional attributes to enhance the NAN command
interface. Define additional 3 new attributes for conveying
type of NAN subcmd and channel information.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Present implementation of NAN vendor command does not use
attribute encapsulation for sending the command from userspace
to the driver, payload is directly sent as is. Attribute
QCA_WLAN_VENDOR_ATTR_NAN is used only for receiving vendor
events in the userspace from the driver. Update the doc as per
this implementation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The max supported ADDBA buffer size value is 256, so change
the buffer size attribute type to U16 to configure the testbed
device to use the 256 buffer size in ADDBA negotiation in 11ax
testing.
This attribute is used only to configure a testbed device and the old
definition of this attribute was not used in any deployed implementation
hence it is still justifiable to change the definition.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_GSCAN_MAX_BLACKLIST_BSSID to get maximum
blacklist BSSIDs capability from the driver for gscan.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
GCM-AES-256 cipher suite is defined in IEEE Std 802.1AEbn-2011.
If authenticator configured as GCM-AES-256, the distributed SAK will be
256 bits indicated by the GCM-AES-256 ID in the MKA packet.
This patch will make AES Key Unwrap to 32 bytes of SAK when identify the
ID.
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Add a new test config QCA vendor attribute to override the MU EDCA
parameters to default values in the driver for test configuration. This
is used for configuring the testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure HE
trigger frame MAC padding duration value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attributes to configure
HE MU EDCA parameters value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure Tx
beamformee number of space-time streams value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The AKM 00-0F-AC:13 is supposed to use cryptographic algorithms
consistently, but the current IEEE 802.11 standard is not doing so for
the key names: PMKID (uses SHA-1), PMKR0Name/PMKR1Name (uses SHA-256).
The PMKID case was already implemented with SHA-384 and this commit
replaces use of SHA-256 with SHA-384 for PMKR0Name/PMKR1Name derivation
to be consistent in SHA-384. While this is not compliant with the
current IEEE 802.11 standard, this is clearly needed to meet CNSA Suite
requirements. Matching change is being proposed in REVmd to get the IEEE
802.11 standard to meet the use case requirements.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This defines key lengths for SHA384-based FT AKM and handles writing and
parsing for RSNE AKMs with the new value.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit adds a new vendor command attribute
QCA_WLAN_VENDOR_ATTR_CONFIG_GTX in
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION to enable/disable green
Tx power saving feature.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends the SAE implementation in both infrastructure and mesh BSS
cases to allow an optional Password Identifier to be used. This uses the
mechanism added in P802.11REVmd/D1.0. The Password Identifier is
configured in a wpa_supplicant network profile as a new string parameter
sae_password_id. In hostapd configuration, the existing sae_password
parameter has been extended to allow the password identifier (and also a
peer MAC address) to be set. In addition, multiple sae_password entries
can now be provided to hostapd to allow multiple per-peer and
per-identifier passwords to be set.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add NAN attributes to communicate IPv6 address, port, and protocol
between wifihal and host driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Over time a number of style issues have crept into qca-vendor.h,
so fix most of them. There are some identifiers and comments which
exceed 80 columns, but these are left as-is for readability.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This can be used to determine which mechanism to use for configuring
country code from trusted sources.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure Tx
beamformee in the driver. This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
OpenSSL started reporting failures from
EC_POINT_set_affine_coordinates_GFp() similarly to BoringSSL, so use the
same workaround to enable this protocol testing case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add commands to allow an AP to configure filtering rules to capture
frames from stations that are active on the operating channel, but
not associated to this AP. Operations include add/delete the filter
and get the statistics information of the unassociated stations.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Extend RADIUS DAS to support CoA-Request packets for the case where the
HS 2.0 Terms And Conditions filtering VSA is used to remove filtering.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Mark a channel as required DFS based on regulatory information received
from the driver/kernel rather than deciding based on hardcoded
boundaries on the frequency. Previously few channels were being marked
as requiring DFS even though they were non-DFS in a particular country.
If the driver does not provide channel list information, fall back to
the previously used frequency-based determination.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend wpa_supplicant WNM-Notification RX handling to parse and process
received Terms and Conditions Acceptance notifications. If PMF is
enabled for the association, this frame results in control interface
indication (HS20-T-C-ACCEPTANCE <URL>) to get upper layers to guide the
user through the required acceptance steps.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd Access-Accept processing to check if the RADIUS
server indicated that Terms and Conditions Acceptance is required. The
new hs20_t_c_server_url parameter is used to specify the server URL
template that the STA is requested to visit.
This commit does not enable any kind of filtering, i.e., only the part
of forwarding a request from Access-Accept to the STA using
WNM-Notification is covered.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows user to get event indication when a new interface is
added/removed for 4addr WDS STA and also WDS STA ifname is informed
through the STA command.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
While it is unlikely that FILS would be used without PMF or SAE in the
build, it is possible to generate such a build and as such, it would be
good for the KDF selection to work properly. Add CONFIG_FILS as an
independent condition for the SHA256-based KDF. Previously, this
combination would have resulted in failure to derive keys and terminated
key management exchange.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd processing of (Re)Association Request frames to
store a local copy of the Consortium OI within the Roaming Consortium
Selection element, if present, and then add that in HS 2.0 Roaming
Consortium attribute into RADIUS Access-Request messages.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends wpa_supplicant Hotspot 2.0 ANQP routines to allow the
Operator Icon Metadata ANQP-element to be fetched with "ANQP_GET <bssid>
hs20:12". The result is available in the new hs20_operator_icon_metadata
entry in the "BSS <bssid>" output.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
At least LibreSSL v2.7.2 indicates support for OpenSSL API 1.1.0, but it
does not apparently use const ASN1_OBJECT * with X509_ALGOR_get0(). Use
the older non-const version here with LibreSSL to fix compilation.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gives more protection against unexpected behavior if RSN supplicant
code ends up trying to use sm->pmk[] with a stale value. Couple of the
code paths did not clear sm->pmk_len explicitly in cases where the old
PMK is being removed, so cover those cases as well to make sure these
will result in PMK-to-PTK derivation failures rather than use of
incorrect PMK value if such a code path could be reached somehow.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a new wifi test config attribute to configure HE LTF in the
driver. This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
In the current implementation, upon an EAP method failure, followed by
an EAP failure, the EAP Status is propagated up in wpa_supplicant with a
general failure parameter string "failure". This parameter is used for a
notification on the dbus.
This commit reports the EAP method failure error code in a separate
callback.
The solution in this commit is generic to all EAP methods, and can be
used by any method that need to pass its error code. However, this
commit only implements the reporting for EAP-SIM and EAP-AKA methods
where the Notification Code (in AT_NOTIFICATION) is used as the method
specific error code value.
Signed-off-by: Ahmed ElArabawy <arabawy@google.com>
This extends the original IEEE Std 802.11ai-2016 functionality with the
changes added in REVmd to describe how additional keys are derived to
protect the FT protocol using keys derived through FILS authentication.
This allows key_mgmt=FT-FILS-SHA256 to be used with FT protocol since
the FTE MIC can now be calculated following the changes in REVmd. The
FT-FILS-SHA384 case is still unsupported (it needs support for variable
length MIC field in FTE).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous implementation ended up defaulting to using PRF-SHA1 for
deriving PTK from PMK when SAE was used. This is not correct since the
SAE AKM is defined to be using SHA-256 -based KDF instead. Fix that.
Note: This change is not backwards compatible. Both the AP and station
side implementations will need to be updated at the same time to
maintain functionality.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an event callback for EVENT_STATION_OPMODE_CHANGED to allow
user/application to get the notification whenever there is a change in a
station's HT/VHT op mode.
The new events:
STA-OPMODE-MAX-BW-CHANGED <addr> <20(no-HT)|20|40|80|80+80|160>
STA-OPMODE-SMPS-MODE-CHANGED <addr> <automatic|off|dynamic|static>
STA-OPMODE-N_SS-CHANGED <addr> <N_SS>
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
To retain configurator information across hostapd/wpa_supplicant
restart, private key need to be maintained to generate a valid pair of
authentication keys (connector, netaccess_key, csign) for new enrollees
in the network.
Add a DPP_CONFIGURATOR_GET_KEY control interface API through which the
private key of an existing configurator can be fetched.
Command format:
DPP_CONFIGURATOR_GET_KEY <configurator_id>
The output from this command can then be used with
"DPP_CONFIGURATOR_ADD key=<hexdump>" to create the same key again.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The SAE AKM 00-0F-AC:8 is supposed to use EAPOL-Key Key Descriptor
Version 0 (AKM-defined) with AES-128-CMAC and NIST AES Key Wrap.
However, the previous implementation ended up using Key Descriptor
Version 2 (HMAC-SHA-1-128 and NIST AES Key Wrap). Fix this by using the
appropriate Key Descriptor Version and integrity algorithm. Use helper
functions to keep the selection clearer and more consistent between
wpa_supplicant and hostapd uses.
Note: This change is not backwards compatible. Both the AP and station
side implementations will need to be updated at the same time to
maintain functionality.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new WiFi test configuration attributes in QCA vendor
command to configure BA session parameters and to add or
delete a BA session and to configure no ack policy.
This is used for configuring the testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new WiFi test configuration attribute in QCA vendor
command to allow or not to allow WEP/TKIP in HT/VHT/HE mode.
This is used for configuring the testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it easier to understand why "SAE: Failed to select group"
debug entry shows up in cases the selected crypto library does not
support a specific group.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
India supports 5 GHz channels 169 and 173 now. Enable HT40 across
channels 165 and 169. Leave channel 173 to remain HT20 only.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Enhance QCA vendor specific APF interface to support write/read program
and/or data and to enable/disable APF feature.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new QCA vendor sub command for configuring the device with wifi
test configuration. Add new test config attributes for this sub command
that are used to configure the device for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The blocking timeout of this function was changed from 2 seconds to 10
seconds in this commit 1480633f ("Use longer timeout in
wpa_ctrl_request()"), but the description was never changed accordingly.
Signed-off-by: Simon Dinkin <simon.dinkin@tandemg.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add new QCA vendor commands and attributes to get thermal information
and send thermal shutdown related commands. Indicates the driver to
enter the power saving mode or resume from the power saving mode based
on the given temperature and thresholds.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
