If one or more BSS from the interface is partnering with BSSs from
another interface and if this interface gets disabled, the Beacon frames
need to be refreshed for other interfaces. Similar thing should happen
when it gets enabled.
Add logic to refresh other interface Beacon frames when one of the
interfaces is disabled or enabled.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Previously, whenever if_remove() was called, the whole interface was
deleted. In an AP MLD, all partner BSS use the same driver private
context and hence removing the interface when only one of the links goes
down should be avoided.
Add a helper function to remove a link first whenever if_remove() is
called. Later while handling it, if the number of active links goes to
0, if_remove() would be called to clean up the interface.
This helper function will be used later when co-hosted AP MLD support is
added and as well later during ML reconfiguration support.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
When the interface was removed, the added links were not removed. While
removing the interface, kernel has removed the stale links but hostapd
has not. This is wrong since hostapd should remove and do the clean ups
properly while removing the interface.
Hence, remove the links when interface is removed.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Construct the nl80211 remove link command using the per-BSS approach
instead of per-driver (drv->first_bss).
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
nl80211_remove_links() iterated over all active links in the given BSS
and removed all of them. However, at times it is required to remove only
one link and not all links.
Add a helper function nl80211_remove_link() which will remove just the
given link_id from the passed BSS. nl80211_remove_links() will use this
and will call this for each of the active links to be removed.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
wpa_driver_nl80211_set_ap() called nl80211_put_freq_params() twice if AP
is an AP MLD. It called once while putting the MLO link ID and the other
time in the normal flow if frequency info is present. Doing this twice
is not required.
Call put_freq once during the normal flow only and separately of that,
add the link ID for AP MLD.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
This call was added within a conditional CONFIG_IEEE80211AX block even
though this can apply without that build option. Move this outside that
conditional block.
Fixes: b3921db426 ("nl80211: Add frequency info in start AP command")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Cache the corresponding hostapd_data struct context into the link entry
within the driver wrapper. This will be useful for driver events
callback processing.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Currently, whenever a new BSS is created, if it is an EHT BSS it is tied
to a corresponding MLD structure. If the structure does not exist
already, a new one is created and tied to it. Accordingly, the link ID
is assigned as well. However, when the BSS is deleted, the MLD structure
is not freed and when it is again created the next time, the link ID is
incremented further and the BSS gets a wrong link ID.
For example, 2.4 GHz single link AP MLD case: First ADD, link ID 0 would
be assigned and MLD interface wlan0 would be created. When REMOVE is
issued, the BSS would be deleted but MLD wlan0 will not. When ADD is
issued again, the BSS will tie back to MLD wlan0 but this time the link
ID will be incremented again and 1 would be assigned. Hence, at
subsequent REMOVE/ADD, the link ID keeps on incrementing.
Since the link ID remains same for the full lifetime of the BSS and MLD,
the next link ID counter cannot be just reset back to 0 when a BSS is
deleted. Otherwise, in interleaved link enable/disable case, the link ID
would be changed.
To overcome this situation, whenever a BSS is deleted, if the MLD is not
referenced by any other existing BSS, delete the MLD structure itself.
To know how many BSSs are referring a given MLD, introduce a new member
refcount in MLD. If the value is 0 it is safe to delete the MLD.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link ID was assigned when BSS is going through setup and the driver
interface init. Later if interface is disabled and enabled again, setup
BSS is called which will give a new link ID to it. However, Link ID
should be same for a BSS affliated to an AP MLD for the full lifetime of
the BSS.
Hence, assign the link ID during BSS creation itself. And it will remain
until BSS entry is completely freed. Hence, link ID will not change as
part of disable/enable.
Also, since link ID would be decided now, it will help in creating link
level control sockets in a subsequent patch.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
MLD level structure is present to store the MLD level information.
Add changes to use the MLD structure instead of link specific struct
hostapd_data to get/set the MLD level information.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
MLD level information like MLD MAC address, next link ID, etc. was
stored in each BSS. However, only the first link BSS assigns values to
these members and the other link BSSs store references to the first BSS.
However, if the first BSS is disabled, the first BSS reference in all
BSS should be updated which is an overhead. Also, this does not seem to
scale.
Instead, a separate MLD level structure can be maintained which can
store all this ML related information. All affiliated link BSSs can keep
reference to this MLD structure.
This commit adds that MLD level structure. However, assigning values to
it and using that instead of BSS level members will be done in
subsequent commits.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
mld_id was provided as a user configuration to identify partner BSS
belonging to the same AP MLD. The same id is used at the protocol level
also to indicate the AP MLD ID of the MLD.
But, in general mld_id is a relative reference of the MLD where 0 is
used as the mld_id to represent the self MLD and in case of MLO MBSSID
mld_id of a non transmitted BSS affiliated to an AP MLD is based on the
relative BSS index of the non transmitted BSS from the transmitted BSS.
Hence mld_id need not be fetched from users, rather it can be identified
wherever required.
To verify if the partners belong to the same AP MLD the interface name
can be checked, since all link BSS partners of the same AP MLD belong to
the same interface.
Hence, remove use of mld_id user config and instead introduce two
functions hostapd_is_ml_partner() and hostapd_get_mld_id(). The former
is used to verify whether partners belong to the same AP MLD and the
latter is used to get the MLD ID of the BSS.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
This is needed to avoid failures due to previous test cases having left
sae_groups set to something else than the default.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
In the code review, it was found that param->freq is accessed without
NULL check in wpa_driver_nl80211_set_ap(), while in other sections of
the code, freq is accessed only after NULL validation. This situation
could result in a segmentation fault at least in theory.
Add a NULL check for freq before accessing it to be consistent with the
other uses.
Fixes: 0c6c948047 ("nl80211: Support setting up an AP on a specified link")
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
This wrapper function was not used at all, so remove it to make it
clearer that the set_ap() driver op is called only from hostapd code.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
mlme_event() calls nl80211_get_link_id_by_freq() to determine the link
to handle reported events. However, in channel switch event it is always
setting freq to the default link that leads to the issue that all other
events that go to mlme_event() will be handled in the default link.
Fix this by setting freq to the correct link specified by the link ID
when processing the event for a completed channel switch.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
This cleans up the implementation and makes stopping of sigma_dut (and
cleanup after some parameters it might leave behind) more robust.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for this test case to fail if a previously executed test
case left another BSS entry for the BSSID used by the second AP here.
That could have skipped the needed scan with scan_for_bss(bssid2). Force
this command to run a new scan to discover the second AP correctly.
Signed-off-by: Jouni Malinen <j@w1.fi>
The NL80211_CMD_DEL_BEACON command was always sent to the main interface
of the radio instead of the desired BSS interface, e.g., when sending a
STOP_AP control interface command from upper layer.
Signed-off-by: Nikita Chernikov <nchernikov@maxlinear.com>
In case we run command like:
wpa_cli -g <global_ctrl_path> command
don't print
"Selected interface " message.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Define attribute QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_LINK_ID in
enum qca_wlan_vendor_attr_ratemask_params to configure ratemask
per MLO link. If the attribute is not provided, ratemask will be
applied for setup link.
Signed-off-by: Shailendra Singh <quic_shasing@quicinc.com>
Add a new QCA vendor sub-command
QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_COMPLETE which will be used as a
netlink event to indicate the completion of a spectral scan request.
This event can also be sent incase of the spectral scan request timeout.
To be able to configure the timeout the value, add a new vendor
attribute QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COMPLETION_TIMEOUT in
enum qca_wlan_vendor_attr_spectral_scan.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a vendor attribute QCA_WLAN_VENDOR_ATTR_SPECTRAL_DATA_TRANSPORT_MODE
to indicate the current spectral data transport mechanism to be used to
get spectral scan samples from the driver to userspace.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
These test cases check the BSS entry information and if the kernel scan
cache maintains an old BSS entry for a previous test case for the same
BSSID this can result in a false failure.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When wpa_supplicant needed to update the internal BSS table with the
latest scan results from the driver, it fetched all BSSs and processed
them all. This is unnecessary for cases where an update is needed only
for a specific BSS. Optimize this by filtering out the unnecessary
entries from the results.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Commit 117e812d06 ("Update BSS table entry if roaming event indicates
frequency change") added wpa_supplicant BSS table update based on the
latest driver scan results whenever processing an association event that
results in the current operating channel changing. While that is needed
to cover the case where an AP changes its own operating channel (and
that is noticed as a roam or new connection instead of a channel switch
event), this should not really be needed for cases where the
wpa_supplicant entry for the new BSS is already up to date.
Skip the full BSS table update on association event if the event is for
a roaming case to a different BSS and the BSS entry for the target is
already available and for the current operating channel. This avoids
undesired latency when processing the association event.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Update EAP-WSC parameters to include Multi-AP profile info to pass the
profile information through the provisioning steps. This is needed for
provisioning the STA configuration when different profiles are used.
Signed-off-by: Manoj Sekar <quic_sekar@quicinc.com>
Add support to fill "multi_ap_vlanid" info to the hostapd config file.
Add the Multi-AP Default 802.1Q Setting subelement into Multi-AP element
generating and parsing.
Signed-off-by: Manoj Sekar <quic_sekar@quicinc.com>
Add a new config option "multi_ap_client_disallow" to control allowing
backhaul STA with certain profiles alone to associate. This is done to
adhere to Wi-Fi EasyMesh specification which defined rules to
allow/disallow association of backhaul STA of certain profiles.
Signed-off-by: Manoj Sekar <quic_sekar@quicinc.com>
Allow both hostapd and wpa_supplicant to be configured with the
supported Multi-AP profile. The configured value will be advertised in
the Multi-AP element.
Signed-off-by: Manoj Sekar <quic_sekar@quicinc.com>
This makes it more convenient to handle extensions to the element and
allows code to be shared between hostapd and wpa_supplicant.
Signed-off-by: Manoj Sekar <quic_sekar@quicinc.com>
Replace the hardcoded buffer length with the actually number of
remaining bytes on the buffer. This is needed to be able to do real
buffer size validation within add_multi_ap_ie().
Furthermore, make hostapd_eid_multi_ap() static since it is not used
outside this file.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This makes the test care less likely to fail due to another STA
happening to be listening for Public Action frames and replying to the
P2P GO Negotiation Request.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check that each test case function includes a title in __doc__ and also
verify that the same test case is not added multiple times from
different files.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not disable HT support on the GO and wait for the channel switch
event on the P2P Client before proceeding with connectivity test.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add ANQP fields to the BSS properties to allow DBus clients to be
notified and obtain the values when it changes.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
Add a D-Bus method to perform ANQP get requests. The new method is
equivalent to the "anqp_get" command available in wpa_cli.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
