178 lines
5.1 KiB
ReStructuredText
178 lines
5.1 KiB
ReStructuredText
User Manual
|
|
###########
|
|
|
|
This manual is an early work in progress, not least because Liminix is
|
|
not yet ready for users who are not also developers.
|
|
|
|
Configuring for your use case
|
|
*****************************
|
|
|
|
You need to create a ``configuration.nix`` that describes your router
|
|
and the services that you want to run on it. Start by copying
|
|
``vanilla-configuration.nix`` and adjusting it, or look in the `examples`
|
|
directory for some pre-written configurations.
|
|
|
|
If you want to create a configuration that can be installed on
|
|
a hardware device, be sure to include the "flashable" module.
|
|
|
|
.. code-block: nix
|
|
|
|
imports = [
|
|
./modules/flashable.nix
|
|
]
|
|
|
|
|
|
|
|
Building and flashing
|
|
*********************
|
|
|
|
An example command to build Liminix might look like this:
|
|
|
|
.. code-block:: console
|
|
|
|
nix-build -I liminix-config=./tests/smoke/configuration.nix \
|
|
--arg device "import ./devices/qemu" -A outputs.default
|
|
|
|
In this command ``<liminix-config>`` points to your
|
|
``configuration.nix``, ``device`` is the file for your hardware device
|
|
definition, and ``outputs.default`` will generate some kind of
|
|
Liminix image output appropriate to that device.
|
|
|
|
For the qemu device in this example, ``outputs.default`` is an alias
|
|
for ``outputs.vmbuild``, which creates a directory containing a
|
|
squashfs root image and a kernel. You can use the `mips-vm` command to
|
|
run this.
|
|
|
|
For the currently supported hardware devices, ``outputs.default``
|
|
creates a directory containing a file called ``firmware.bin``. This
|
|
is a raw image file that can be written directly to the firmware flash
|
|
partition.
|
|
|
|
|
|
Flashing with :command:`flashcp`
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
This requires an existing Liminix system, or perhaps some other
|
|
operating system on the device which provides the :command:`flashcp`
|
|
command. You need to locate the "firmware" partition, which you can do
|
|
with a combination of :command:`dmesg` output and the contents of
|
|
:file:`/proc/mtd`
|
|
|
|
.. code-block:: console
|
|
|
|
<5>[ 0.469841] Creating 4 MTD partitions on "spi0.0":
|
|
<5>[ 0.474837] 0x000000000000-0x000000040000 : "u-boot"
|
|
<5>[ 0.480796] 0x000000040000-0x000000050000 : "u-boot-env"
|
|
<5>[ 0.487056] 0x000000050000-0x000000060000 : "art"
|
|
<5>[ 0.492753] 0x000000060000-0x000001000000 : "firmware"
|
|
|
|
# cat /proc/mtd
|
|
dev: size erasesize name
|
|
mtd0: 00040000 00001000 "u-boot"
|
|
mtd1: 00010000 00001000 "u-boot-env"
|
|
mtd2: 00010000 00001000 "art"
|
|
mtd3: 00fa0000 00001000 "firmware"
|
|
mtd4: 002a0000 00001000 "kernel"
|
|
mtd5: 00d00000 00001000 "rootfs"
|
|
|
|
Then you can copy the image to the device with :command:`ssh`
|
|
|
|
.. code-block:: console
|
|
|
|
build-machine$ tar chf - result/firmware.bin | \
|
|
ssh root@the-device tar -C /run -xvf -
|
|
|
|
and then connect to the device and run
|
|
|
|
|
|
.. code-block:: console
|
|
|
|
flashcp firmware.bin /dev/mtd3
|
|
|
|
|
|
|
|
Flashing from OpenWrt (untested)
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
If your device is running OpenWrt then it probably has the
|
|
:command:`mtd` command installed and you can use it as follows:
|
|
|
|
.. code-block:: console
|
|
|
|
mtd -r write /tmp/firmware_image.bin firmware
|
|
|
|
For more information, please see the `OpenWrt manual <https://openwrt.org/docs/guide-user/installation/sysupgrade.cli>`_
|
|
|
|
|
|
Flashing from the boot monitor
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
If you are prepared to open the device and have a TTL serial adaptor
|
|
or some kind to connect it to, you can probably flash it using U-Boot.
|
|
This is quite hardware-specific: please refer to the Developer Manual.
|
|
|
|
|
|
|
|
Updates to running devices
|
|
**************************
|
|
|
|
To mitigate the risk of flashing a new configuration and potentially
|
|
render the device unresponsive if the configuration is unbootable or
|
|
doesn't bring up a network device, Liminix has a
|
|
"try before write" mode.
|
|
|
|
To test a configuration without writing it to flash, import the
|
|
``kexecboot`` module and build ``outputs.kexecboot`` instead of
|
|
``outputs.default``. This generates a directory containing the root
|
|
filesystem image and kernel, along with an executable called `kexec`
|
|
and a `boot.sh` script that runs it with appropriate arguments.
|
|
|
|
For example
|
|
|
|
.. code-block:: console
|
|
|
|
nix-build --show-trace -I liminix-config=./examples/arhcive.nix \
|
|
--arg device "import ./devices/gl-ar750"
|
|
-A outputs.kexecboot && \
|
|
(tar chf - result | ssh root@the-device tar -C /run -xvf -)
|
|
|
|
and then login to the device and run
|
|
|
|
.. code-block:: console
|
|
|
|
cd /run/result
|
|
sh ./boot.sh .
|
|
|
|
|
|
This will load the new kernel and map the root filesystem into a RAM
|
|
disk, then start executing the new kernel. *This is effectively a
|
|
reboot - be sure to close all open files and finish anything else
|
|
you were doing first.*
|
|
|
|
If the new system crashes or is rebooted, then the device will revert
|
|
to the old configuration it finds in flash. Thus, by combining kexec
|
|
boot with a hardware watchdog you can try new images with very little
|
|
chance of bricking anything. When you are happy that the new
|
|
configuration is correct, build and flash a flashable image of it.
|
|
|
|
|
|
|
|
Module options (tbd)
|
|
**************
|
|
|
|
|
|
|
|
Foo module
|
|
==========
|
|
|
|
Module docs will go here. This part of the doc should be autogenerated.
|
|
|
|
|
|
Bar module
|
|
==========
|
|
|
|
Baz module
|
|
==========
|
|
|
|
Quuz net device
|
|
===============
|