Fast Session Transfer (FST) is the transfer of a session from a channel
to another channel in a different frequency band. The term "session"
refers to non-physical layer state information kept by a pair of
stations (STAs) that communicate directly (i.e., excludes forwarding).
The FST is implemented in accordance with IEEE Std 802.11ad-2012.
Definitions
* FST interface - an interface for which FST functionality is enabled
* FST group - a bunch of FST interfaces representing single
multi-band STA
* FST peer - a multi-band capable STA connected
* FST module - multi-band operation functionality implemented in
accordance with IEEE Std 802.11ad-2012 (see 10.32
Multi-band operation) as a part of hostapd/wpa_supplicant
* FST manager - an external application that implements custom FST
related logic, using the FST module's interfaces
accessible via CLI or D-Bus
This commit introduces only the FST module. Integration of the FST
module into the hostapd/wpa_supplicant and corresponding CLI/D-Bus
interfaces and FST related tests are covered in separate commits.
FST manager application is out of scope of these commits.
As FST aggregates a few interfaces into FST group, the FST module uses
global CLI for both commands and notifications. It also exposes
alternative non-interface based D-Bus subtree for this purposes.
Configuration and Initialization
* FST functionality can enabled by compilation flag (CONFIG_FST)
* hostapd/wpa_supplicant controlling multiple interfaces are used for
FST
* once enabled by compilation, the FST can be enabled for specific
interfaces in the configuration files
* FST interfaces are aggregated in FST groups (fst_group_id config file
entry), where each FST group:
- represents one multi-band device
- should have two or more FST interfaces in it
* priority (fst_priority config file entry) must be configured for each
FST interface. FST interface with higher priority is the interface FST
will always try to switch to. Thus, for example, for the maximal
throughput, it should be the fastest FST interface in the FST setup.
* default Link Loss Timeout (LLT) value can be configured for each FST
interface (fst_llt config file entry). It represents LLT to be used
by FST when this interface is active.
* FST interfaces advertise the Multi-band capability by including the
Multi-band element in the corresponding frames
FST CLI commands:
* fst list_groups - list FST groups configured.
* fst list_ifaces - list FST interfaces which belong to specific group
* fst iface_peers - list Multi-Band STAs connected to specific interface
* fst list_sessions - list existing FST sessions
* fst session_get - get FST session info
* fst session_add - create FST session object
* fst session_set - set FST session parameters (old_iface, new_iface,
peer_addr, llt)
* fst session_initiate - initiate FST setup
* fst session_respond - respond to FST setup establishemnt attempt by
counterpart
* fst session_transfer - initiate FST switch
* fst session_teardown - tear down FST Setup but leave the session object
for reuse
* fst session_remove - remove FST session object
FST CLI notifications:
* FST-EVENT-PEER - peer state changed (CONNECT/DISCONNECT)
* FST-EVENT-SESSION - FST session level notification with following
sub-events:
- EVENT_FST_SESSION_STATE - FST session state changed
- EVENT_FST_ESTABLISHED - previously initiated FST session became
established
- EVENT_FST_SETUP - new FST session object created due to FST session
negotiation attempt by counterpart
All the FST CLI commands and notifications are also implemented on D-Bus
for wpa_supplicant.
IEEE 802.11 standard compliance
FST module implements FST setup statemachine in compliance with IEEE
802.11ad (P802.11-REVmc/D3.3), as it described in 10.32 Multi-band
operation (see also Figure 10-34 - States of the FST setup protocol).
Thus, for example, the FST module initiates FST switch automatically
when FST setup becomes established with LLT=0 in accordance with
10.32.2.2 Transitioning between states.
At the moment, FST module only supports non-transparent STA-based FST
(see 10.32.1 General).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The FT-specific check for valid group cipher in wpa_ft_gen_req_ies() was
not up-to-date with the current list of supported ciphers. Fix this by
using a generic function to determine validity of the cipher. In
practice, this adds support for using CCMP-256 and GCMP-256 as the group
cipher with FT.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to have separate return statements for these corner
cases that are unlikely to be hit in practice.
Signed-off-by: Jouni Malinen <j@w1.fi>
The cwmin/cwmax parameters were limited more than is needed. Allow the
full range (0..15 for wmm_ac_??_{cwmin,cwmax} and 1..32767 for
tx_queue_data?_{cwmin,cwmax}) to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The current P802.11 description of SAE uses "1 < element < p" as the
required range. However, this is not correct and does not match the
Dragonfly description of "1 < element < p-1". SAE definition will need
to change here. Update the implementation to reject p-1 based on the
correct rule here.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2012 description of SAE does not require this, i.e., it
describes the requirement as 0 < scalar < r for processing the Commit
message. However, this is not correct and will be changes to 1 < scalar
< r to match the Dragonfly description so that a trivial secret case
will be avoided explicitly.
This is not much of an issue for the locally generated commit-scalar
since it would be very unlikely to get the value of 1. For Commit
message processing, a peer with knowledge of the password could
potentially force the exchange to expose key material without this
check.
Signed-off-by: Jouni Malinen <j@w1.fi>
This provides more information to upper layer programs on what happens
with connection attempts in cases where the enabled networks are not
found in scan results.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
If PWE is discovered before the minimum number of loops (k) is reached,
the extra iterations use a random "password" to further obfuscate the
cost of discovering PWE.
Signed-off-by: Jouni Malinen <j@w1.fi>
This replaces the earlier IEEE Std 802.11-2012 algorithm with the design
from P802.11-REVmc/D4.0. Things brings in a blinding technique for
determining whether the pwd-seed results in a suitable PWE value.
Signed-off-by: Jouni Malinen <j@w1.fi>
draft-irtf-cfrg-dragonfly recommends implementation to set the security
parameter, k, to a value of at least 40. This will make PWE generation
take significantly more resources, but makes it more likely to hide
timing differences due to different number of loops needed to find a
suitable PWE.
Signed-off-by: Jouni Malinen <j@w1.fi>
This check explicitly for reflection attack and stops authentication
immediately if that is detected instead of continuing to the following
4-way handshake that would fail due to the attacker not knowing the key
from the SAE exchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to have separate return statements for these corner
cases that are unlikely to be hit in practice.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to have a separate "fail silently" case for wpa_ie_len
== 0. That condition does not seem to be reachable and even if it were,
the following "ie len too short" case will result in the exact same
return value.
Signed-off-by: Jouni Malinen <j@w1.fi>
As far as IEEE 802.11 standard is concerned, WEP is deprecated, but at
least in theory, allowed as a group cipher. This option is unlikely to
be deployed anywhere and to clean up the implementation, we might as
well remove all support for this combination.
Signed-off-by: Jouni Malinen <j@w1.fi>
CA country code was included mistakenly (copy-paste..) in cn_op_class_cc
while it was supposed to be included only in us_op_class_cc. In
practice, this did not result in incorrect operation due to the
us_op_class_cc list being checked first. Anyway, better fix
cn_op_class_cc to avoid confusion here.
Signed-off-by: Jouni Malinen <j@w1.fi>
This increases code coverage for gas.c testing to cover areas that
cannot be reached with pure hwsim test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add operating class 125 (channels 149..169) to the list of P2P supported
channels. This allows the 5 GHz channels 161 and 169 to be used for P2P
GO when those channels are allowed for AP mode in the current regulatory
domain.
Signed-off-by: Amr BEN ABDESSALEM <amrx.ben.abdessalem@intel.com>
When device supports dual band operations with offloaded ACS, hw_mode
can now be set to any band (hw_mode=any) in order to allow ACS to select
the best channel from any band. After a channel is selected, the hw_mode
is updated for hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Link Property query vendor command shall facilitate the information
of the Wi-Fi link. MAC address of the Wi-Fi peer is given as an input
for querying the link properties.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Remove the length field from struct ieee802_11_elems since the only
allowed element length is five and that is checked by the parser.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the only allowed element length is one.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the only allowed element length is one.
Signed-off-by: Jouni Malinen <j@w1.fi>
All the existing users of these elements were already validating the
element length. However, it is clearer to validate this already at the
parser for extra layer of protection for any future changes.
Signed-off-by: Jouni Malinen <j@w1.fi>
This program can be used to run fuzzing tests for areas related to P2P
message parsing and processing. p2p-fuzzer allows data files to be used
to inject Probe Response and Action frames for processing by the P2P
module.
Signed-off-by: Jouni Malinen <j@w1.fi>
The SSID element is defined to have a valid length range of 0-32. While
this length was supposed to validated by the users of the element
parser, there are not really any valid cases where the maximum length of
32 octet SSID would be exceeded and as such, the parser itself can
enforce the limit as an additional protection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Both Android's libc and glibc support _FORTIFY_SOURCE, a compiler
and libc feature which inserts automatic bounds checking into
common C functions such as memcpy() and strcpy(). If a buffer
overflow occurs when calling a hardened libc function, the
automatic bounds checking will safely shutdown the program and
prevent memory corruption.
Android is experimenting with _FORTIFY_SOURCE=3, a new fortify
level which enhances memcpy() to prevent overflowing an element
of a struct. Under the enhancements, code such as
struct foo {
char empty[0];
char one[1];
char a[10];
char b[10];
};
int main() {
foo myfoo;
int n = atoi("11");
memcpy(myfoo.a, "01234567890123456789", n);
return 0;
}
will cleanly crash when the memcpy() call is made.
Fixup hostap code to support the new level. Specifically:
* Fixup sha1_transform so it works with the enhanced bounds checking.
The old memcpy() code was attempting to write to context.h0, but that
structure element is too small and the write was extending (by design)
into h1, h2, h3, and h4. Use explicit assignments instead of
overflowing the struct element.
* Modify most of the structures in ieee802_11_defs.h to use ISO C99
flexible array members (https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html)
instead of a zero length array. Zero length arrays have zero length,
and any attempt to call memcpy() on such elements will always overflow.
Flexible array members have no such limitation. The only element not
adjusted is probe_req, since doing so will generate a compile time error,
and it's not obvious to me how to fix it.
Signed-off-by: Nick Kralevich <nnk@google.com>
wpa_ctrl.c gets sys/stat.h inherited from
private/android_filesystem_config.h it should
not rely on this in the future. The intent is
to move fs_config function into libcutils and
thus deprecate any need for sys/stat.h in this
include file.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
The new network profile parameter mem_only_psk=1 can be used to specify
that the PSK/passphrase for that network is requested over the control
interface (ctrl_iface or D-Bus) similarly to the EAP network parameter
requests. The PSK/passphrase can then be configured temporarily in a way
that prevents it from getting stored to the configuration file.
For example:
Event:
CTRL-REQ-PSK_PASSPHRASE-0:PSK or passphrase needed for SSID test-wpa2-psk
Response:
CTRL-RSP-PSK_PASSPHRASE-0:"qwertyuiop"
Note: The response value uses the same encoding as the psk network
profile parameter, i.e., passphrase is within double quotation marks.
Signed-off-by: Jouni Malinen <j@w1.fi>
Old code defaulted to WEP for an AP advertising OSEN. Show as OSEN
instead. Re-use most of the RSN parsing logic since all but the header
is the same.
Example output:
[root@ath9k-f lanforge]# ./local/bin/wpa_cli -i sta0 scan_results
bssid / frequency / signal level / flags / ssid
00:0e:8e:6f:40:49 2462 -23 [OSEN-OSEN-CCMP][ESS] ben-138
Signed-off-by: Ben Greear <greearb@candelatech.com>
Update ACS driver offload feature for VHT configuration. In addition,
this allows the chanlist parameter to be used to specify which channels
are included as options for the offloaded ACS case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the AP/Authenticator receives an EAPOL-Key msg 2/4 for an association
that negotiated use of PSK and the EAPOL-Key MIC does not match, it is
likely that the station is trying to use incorrect PSK/passphrase.
Report this with "AP-STA-POSSIBLE-PSK-MISMATCH <STA addr>" control
interface event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Channel 140 is needed as allowed HT40 channel pair to use
channel 144 introduced in 802.11ac for VHT40 and VHT80.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Add handling logic for DFS offloaded case, and add a helper function
that takes the frequency (MHz) as a param and returns 1 if given channel
requires DFS, or 0 otherwise.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These values were previously used only for sorting the scan results, but
it may be useful to provide access to the used values through the BSS
entries.
Signed-off-by: Jouni Malinen <j@w1.fi>
When DFS offloading capability is supported by the driver, the driver
should use these events to indicate when a radar pattern has been
detected, channel availability check (CAC) has been completed, aborted
or finished after the non-occupancy period is over on a DFS channel.
Also, add a new driver.h event to be used by NL80211 to indicate CAC
Started event on a DFS channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When DFS offloading capability is supported by the driver, the driver
should use this event to indicate when channel availability check (CAC)
is started on a DFS channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds testing code (for CONFIG_TESTING_OPTIONS=y builds only) to
send an nl80211 vendor command and report a test vendor event in case
the driver supports this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Send MESH-SAE-AUTH-BLOCKED event if SAE authentication is blocked. The
BLOCK state will finish when a new peer notification event is sent for
the same MAC address.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
SAE authentication fails likely with wrong password. This commit adds a
notification of the failure to the upper application (UI) so that the
application can notify suspection of a wrong password to the user. The
control interface monitor even for this is "MESH-SAE-AUTH-FAILURE
addr=<peer>".
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This modifies struct wpa_ptk to allow the length of KCK and KEK to be
stored. This is needed to allow longer keys to be used, e.g., with
Suite B 192-bit level.
Signed-off-by: Jouni Malinen <j@w1.fi>
The ANQP verification/parsing is done only after the GAS_DONE indication
is sent over the control interface. This means that in case the ANQP
parsing fails there is no indication to the upper layers. Add an
ANQP-QUERY-DONE event that reports the status of the ANQP parsing.
Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
A new "CTRL-EVENT-EAP-PEER-ALT depth=<i> <alt name>" event is now used
to provide information about server certificate chain alternative
subject names for upper layers, e.g., to make it easier to configure
constraints on the server certificate. For example:
CTRL-EVENT-EAP-PEER-ALT depth=0 DNS:server.example.com
Currently, this includes DNS, EMAIL, and URI components from the
certificates. Similar information is priovided to D-Bus Certification
signal in the new altsubject argument which is a string array of these
items.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new VENDOR_ELEM value 13 can now be used to add a vendor element
into all (Re)Association Request frames, not just for P2P use cases like
the previous item was for.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows vendor specific information element to be used to advertise
support for VHT on 2.4 GHz band. In practice, this is used to enable use
of 256 QAM rates (VHT-MCS 8 and 9) on 2.4 GHz band.
This functionality is disabled by default, but can be enabled with
vendor_vht=1 parameter in hostapd.conf if the driver advertises support
for VHT on either 2.4 or 5 GHz bands.
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
There should not be a mesh-specific mechanism for setting up channel
parameters since that will just result in duplicated code. IBSS, mesh,
and AP mode can use the same data structures and parameters for setting
up such parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add the t0 retransmission timer as specified by IEEE Std 802.11-2012,
11.3.8.4. This makes SAE much more likely to succeed in the case of lost
frames.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
There is no need to keep temporary keys in memory beyond the end of the
association, so explicitly clear any SAE buffers that can contain keys
as soon as such keys are not needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
struct wpa_driver_associate_params moved to using struct
hostapd_freq_params instead of just frequency. Need to update wpa_priv
to do same.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit introduces a QCA vendor command that allows interrogation of
the vendor-specific features supported by the device/driver. Currently
the only defined feature is the ability to offload key management.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This converts os_snprintf() result validation cases to use
os_snprintf_error() for cases that were note covered by spatch and
semantic patches.
Signed-off-by: Jouni Malinen <j@w1.fi>
Using QCA vendor command, allow ACS function to be offloaded to the
driver. Once channels are selected, hostapd is notified to perform OBSS
operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit inserts Finite Cyclic Group to Anti-Clogging Token request
frame because IEEE Std 802.11-2012, Table 8-29 says "Finite Cyclic Group
is present if Status is zero or 76".
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The mesh anti-clogging functionality is implemented partially. This
patch fixes to parse anti-clogging request frame and use anti-clogging
token.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Some static analyzers had problems understanding "left < count * len"
(CID 62855, CID 62856), so convert this to equivalent "count > left /
len" (len here is fixed to 4, so this can be done efficiently).
Signed-off-by: Jouni Malinen <j@w1.fi>
Static analyzers may not have understood the bounds checking on
data->num_pmkid. Use a local, temporary variable and validate that that
value is within length limits before assining this to data->num_pmkid to
make this clearer. (CID 62857, CID 68126)
Signed-off-by: Jouni Malinen <j@w1.fi>
Send link measurement response when a request is received. Advertise
only RCPI, computing it from the RSSI of the request. The TX power field
is left to be filled by the driver. All other fields are not published.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add NEIGHBOR_REP_REQUEST command to the wpa_supplicant ctrl_iface.
This command triggers the sending of a Neighbor Report Request to the
associated AP.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Add the ability to send a Neighbor Report Request (part of
RRM). Requester is then notified once the report arrives.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
In case the AP we are associating with advertises support for RRM,
advertise our own RRM support in the (Re)Association Request frame. This
is done by adding an RRM Capabilities IE. The underlying driver is
expected to further add a Power Capabilities IE to the request, and set
the Radio Measurement flag in the Capability Info field. At this point
the RRM Capabilities IE advertises no measurement support.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
ieee80211_chan_to_freq() is a generic function that replaces and extends
the previous P2P-specific p2p_channel_to_freq(). The new function
supports both the global operating class table as well as the additional
US, EU, JP, and CN operating class tables.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible that a station device might miss an ACK for an
authentication, association, or action frame, and thus retransmit the
same frame although the frame is already being processed in the stack.
While the duplicated frame should really be dropped in the kernel or
firmware code where duplicate detection is implemented for data frames,
it is possible that pre-association cases are not fully addressed (which
is the case at least with mac80211 today) and the frame may be delivered
to upper layer stack.
In such a case, the local AP will process the retransmitted frame although
it has already handled the request, which might cause the station to get
confused and as a result disconnect from the AP, blacklist it, etc.
To avoid such a case, save the sequence control of the last processed
management frame and in case of retransmissions drop them.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add the TSPEC to the driver on successful TSPEC ADDTS response. Delete
the TSPEC when receiving DELTS action.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Initialize WMM AC data structures upon successful association
with an AP that publishes WMM support, and deinitialize the data
structure when the association is no longer valid.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Android 4.4 uses "BSS" command instead of "SCAN_RESULT" command.
So this patch add the mesh scan result for BSS command.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Parse MESH_GROUP_ADD/REMOVE commands on ctrl interface and call
wpa_supplicant routines. These commands are used to start or
join and leave a mesh network.
The mesh id is given in the configuration file, therefore there is
no need to scan before joining a mesh network. We reuse the
connect_without_scan construct used by P2P for that same purpose.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Add a new option "mesh_ht_mode" that specifies the HT mode for the
mesh, with this option on, mesh beacons, actions frames, and probe
responses with include the appropriate HT information elements.
[original implementation by Chun-Yeow Yeoh <yeohchunyeow@gmail.com>]
[some fixes by Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
This adds support for AKM 00-0F-AC:11 to specify the integrity and
key-wrap algorithms for EAPOL-Key frames using the new design where
descriptor version is set to 0 and algorithms are determined based on
AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new AKM uses a different mechanism of deriving the PMKID based on
KCK instead of PMK. hostapd was already doing this after the KCK had
been derived, but wpa_supplicant functionality needs to be moved from
processing of EAPOL-Key frame 1/4 to 3/4 to have the KCK available.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds definitions for the 128-bit level Suite B AKM 00-0F-AC:11. The
functionality itself is not yet complete, i.e., this commit only
includes parts to negotiate the new AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed since the SCAN command with radio work returns before the
actual driver operation to trigger a scan has been executed and as such,
cannot return result of that operation.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
These can be convenient for upper layer programs to determine if the
hostapd interface gets disabled/re-enabled, e.g., due to rfkill
block/unblock.
Signed-off-by: Jouni Malinen <j@w1.fi>
The mesh peering manager establishes and maintains links among
mesh peers, tracking each peer link via a finite state machine.
This implementation supports open mesh peerings.
[assorted fixes from Yu Niiro <yu.niiro@gmail.com>]
[more fixes from Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-hostap: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
This commit introduces a QCA vendor command and event to provide an
option to use extended versions of the nl80211 connect/roam operations
in a way that allows drivers to offload key management operations to the
driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The definition of wpa_ctrl_get_remote_ifname is conditional on
CONFIG_CTRL_IFACE_UDP. This change makes the header declaration of
this function also conditional on the same define.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Commit 4fdc8def88 changed the wpa_ctrl
socket to be be non-blocking, so the comment about wpa_ctrl_recv()
blocking is not valid anymore.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows updating roaming policy for drivers that select the BSS
internally so that wpa_supplicant (based on bssid parameter
configuration) and the driver remain in sync.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds hostapd support for the new WLAN-Pairwise-Cipher,
WLAN-Group-Cipher, WLAN-AKM-Suite, and WLAN-Group-Mgmt-Pairwise-Cipher
attributes defined in RFC 7268. These attributes are added to RADIUS
messages when the station negotiates use of WPA/RSN.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows external programs to use vendor specific information from
P2P peers without wpa_supplicant having to be able to parse and
understand all such vendor specific elements.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds following new control interface commands to allow arbitrary
vendor elements to be added into number of frames:
VENDOR_ELEM_ADD <frame id> <hexdump of elem(s)>
VENDOR_ELEM_GET <frame id>
VENDOR_ELEM_REMOVE <frame id> <hexdump of elem(s)>
VENDOR_ELEM_REMOVE <frame id> *
The following frames are supported in this commit (additional frames can
be added in the future):
0 = Probe Request frame in P2P device discovery
1 = Probe Response frame from P2P Device role
2 = Probe Response frame from P2P GO
3 = Beacon frame from P2P GO
4 = PD Req
5 = PD Resp
6 = GO Neg Req
7 = GO Neg Resp
8 = GO Neg Conf
9 = Invitation Request
10 = Invitation Response
11 = P2P Association Request
12 = P2P Association Response
One or more vendor element can be added/removed with the commands. The
hexdump of the element(s) needs to contain the full element (id, len,
payload) and the buffer needs to pass IE parsing requirements to be
accepted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the randomly generated bignum does not meet the validation steps, the
iteration loop in sae_get_rand() did not free the data properly. Fix the
memory leak by freeing the temporary bignum before starting the next
attempt at generating the value.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the NL80211_ATTR_AKM_SUITES was skipped if either of these
SHA256-based AKMs was negotiated.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
Extend the minimal HT 20/40 co-ex support to include dynamic changes
during the lifetime of the BSS. If any STA connects to a 2.4 GHz AP with
40 MHz intolerant bit set then the AP will switch to 20 MHz operating
mode.
If for a period of time specified by OBSS delay factor and OBSS scan
interval AP does not have any information about 40 MHz intolerant STAs,
the BSS is switched from HT20 to HT40 mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Move the definitions that depended in common.h into a separate header
file so that qca-vendor.h can be copied and used as-is in other
projects.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allocates a QCA vendor subcmd for extended statistics
functionality and also an attribute for delivering the payload
for extended statistics.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
