Setting 4addr mode on fronthaul BSS breaks WPS association on backhaul
STA which is still on 3addr mode.
Fix the interop issue by not setting 4addr mode on fronthaul BSS with
WPS instead of setting by default for multi-ap case.
Fronthaul BSS for non-WPS STA shall continue to use 4addr mode.
Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Some of the information elements added in IEEE Std 802.11ax-2013 for VHT
purposes have since then been taken into use for other cases and renamed
to remove the "VHT" prefix in the standard. Update the defines for those
elements in the implementation to match the names used in the current
standard.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add validatation of center frequency, and filling of appropriate
bandwidth in the channel switch wrapper when the channel switch is done
to a 320 MHz channel.
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
As per IEEE Std 802.11ax-2021, 11.1.3.8.3 Discovery of
a nontransmitted BSSID profile, an EMA AP that transmits a Beacon
frame carrying a partial list of nontransmitted BSSID profiles
should include in the frame a Reduced Neighbor Report element
carrying information for at least the nontransmitted BSSIDs that
are not present in the Multiple BSSID element carried in that frame.
Add this support by splitting the reduced neighbor report (RNR) in as
many elements as the number of multiple BSSID elements. Each RNR element
excludes the non-transmitting profiles already included in the MBSSID
element at the same index. If present, the last additional group will
have the data common for all EMA beacons such as neighbor AP information
gathered through neighbor reports.
The hwsim test case he_ap_ema demonstrates this support.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Do not include interfaces on the same radio in reduced neighbor
report elements (RNR) as multiple BSSID elements from the same
management frame already include these if MBSSID feature is enabled.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Add preamble puncturing bitmap to the EHT Operation element as per IEEE
P802.11be/D3.0, Figure 9-1002c (EHT Operation Information field format).
Bits set to 1 indicate that the subchannel is punctured, otherwise
active.
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Legacy modes (VHT, HE) should advertise downgraded bandwidth if
RU puncturing is enabled in EHT mode. This is required for the legacy
stations which cannot parse the EHT Operation elements hence do not
support EHT RU puncturing.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Ramanathan Choodamani <quic_rchoodam@quicinc.com>
As a preparation for processing an association request with
ML element, split the function such that the elements checking
would be separate from parsing.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The received Service Discovery Response frame follows the ap_mgmt_rx()
path in P2P GO mode. If gas_query_rx_frame() doesn't process the frame,
call the Public Action frame callbacks if any are registered for further
processing of the RX frame.
Fixes: 9c2b8204e6 ("DPP: Integration for hostapd")
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Authentication frames include several fixed body parts (see Table 9-68
(Authentication frame body) and Table 9-69 (Presence of fields and
elements in Authentication frames) in IEEE P802.11-REVme/D2.0).
To be able to parse the IE part, these fields need to be skipped. Since
SAE logic already implements this parsing, change SAE authentication
handling functions to return the offset to the IE part. This preparation
is needed for future MLD patches that need to parse out the ML related
elements in the Authentication frames.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add the ability to require HE, advertising that via the
BSS membership selector as well as rejecting association
without HE.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Indicate whether the collocated BSS in the RNR is a part of a multiple
BSSID set and whether it is a transmited BSSID.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
As described in IEEE Std 802.11-2020, 11.1.3.8 Multiple BSSID procedure,
set the lowest AID value assigned to any client equal to 2^n, where n is
the maximum BSSID indicator of the MBSSID set.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Process the Known BSSID elements if included by non-AP stations. The
format is described in IEEE Std 802.11ax-2021, 9.4.2.261.
Non-AP stations may include this element in directed Probe Request
frames to indicate which of the multiple BSSIDs they have already
discovered. AP should exclude these profiles from the Probe Response
frame.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Set extended capabilities as described in IEEE Std 802.11ax-2021,
9.4.2.26. Reset the capability bits to 0 explicitly if MBSSID and/or EMA
is not enabled because otherwise some client devices fail to associate.
Bit 80 (complete list of non-tx profiles) is set for all Probe Response
frames, but for Beacon frames it is set only if EMA is disabled or if
EMA profile periodicity is 1.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Add data per IEEE Std 802.11-2020, 9.4.2.240. Current implementation is
added for the security and extended supported rates only.
For the Extended rates element, add a new member 'xrates_supported'
which is set to 1 only if hostapd_eid_ext_supp_rates() returns success.
Without this change, there are cases where this function returns before
adding the element for the transmitting interface resulting in incorrect
addition of this element inside the MBSSID Non-Inheritance element.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Add Multiple BSSID element data per IEEE Std 802.11ax-2021, 9.4.2.45.
Split the BSSes into multiple elements if the data does not fit in
the 255 bytes allowed for a single element.
Store the total count of elements created and the offset to the start
of each element in the provided buffer.
Set the DTIM periods of non-transmitted profiles equal to the EMA
profile periodicity if those are not a multiple of the latter already as
recommended in IEEE Std 802.11ax-2021, Annex AA (Multiple BSSID
configuration examples).
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
IEEE Std 802.11-2020, 12.4.7.6 says that status code CHALLENGE_FAILURE,
needs to be sent in case the verification action fails for SAE Confirm
message frame from a STA: "An SAE Confirm message, with a status code
not equal to SUCCESS, shall indicate that a peer rejects a previously
sent SAE Confirm message. An SAE Confirm message that was not
successfully verified is indicated with a status code of
CHALLENGE_FAILURE."
hostapd, however, did not use this status code for this case. In
ieee802_11.c the function sae_check_confirm() is called and in case of
verification failure (-1 is returned), the response is set to
WLAN_STATUS_UNSPECIFIED_FAILURE (status code = 1). Fix this to use
CHALLENGE_FAILURE.
Signed-off-by: Koen Van Oost <koen.vanoost@airties.com>
Signed-off-by: Mert Ekren <mert.ekren@airties.com>
When the RADIUS server requests a STA to be deauthenticated imminently
without providing a reason URL, there is no need to allow the STA spend
any additional time associated. Deauthenticate the STA immediately after
it has ACK'ed the WNM-Notification frame indicating imminent
deauthentication or at latest two seconds after having processes the
Access-Accept message.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Using separate variables for BSSID and peer address is needed to support
Wi-Fi Aware (NAN) use cases where the group address is used as the BSSID
and that could be different from any other peer address. The
infrastructure BSS cases will continue to use the AP's BSSID as both the
peer address and BSSID for the PASN exchanges.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Make sure the elements were present before trying to parse them. This
was already done for most cases, but be consistent and check each item
explicitly before use.
Signed-off-by: Jouni Malinen <j@w1.fi>
struct wpas_pasn is common to both initiator and responder, so rename it
to pasn_data to avoid the "wpas_" prefix that could be seen as a
reference to wpa_supplicant (PASN initiator).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
PASN responder validates auth 1 frame and sends auth 2 frame to the
initiator. It analyses the auth 3 frame and verifies successful
authentication. Wi-Fi Aware modules can reuse this functionality through
a shared library libpasn.so generated from this code. Move the PASN
functionality that is now decoupled from the hapd context into a
separate file in a common directory to make it easier to build such a
library.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is helpful in being able to get the functionality needed for SAE
into a separate library (libpasn.so) without needing all of the
ieee802_11.c functionality.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wi-Fi Aware R4 specification defines Beacon RSNE/RSNXE to be same as
RSNE/RSNXE present in Auth2 frame. So, MIC validation should be done
with the RSNE and RSNXE received in Auth2 frame.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wi-Fi Aware R4 specification introduces a custom PMKID derived from
Nonce and TAG. This custom PMKID is included in PASN Authentication
frames during pairing verification. So, allow use of a custom PMKID in
PASN frames and validate it using a function handler. Wi-Fi Aware
component that uses libpasn.so should take care of validating the custom
PMKID.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Introduce a function handler to transmit PASN Authentication frames to
the driver. This removes the hapd dependency for sending the frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
PTK is stored in the PTKSA cache following a successful PASN handshake,
however AKMP is removed upon a WPA PASN reset. The PASN handshake is
used in the Wi-Fi Aware R4 specification to define the pairing setup
process. KDK is used to generate a new set of keys, while AKMP is
required for key derivation for pairing. So, keep AKMP in the PTKSA
cache.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This makes hostapd use the struct defines from pasn_common.h so that the
same struct is shared with wpa_supplicant.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Make struct wpas_pasn common for both the initiator and the responder by
adding required parameters for responder to the existing struct
wpas_pasn. This makes both hostapd and wpa_supplicant share the same
structure definitions in preparation for allowing PASN functionality to
be built into a separate library.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Provide enough information to allow the FTE to be built using the
correct MIC field length based on the used AKM and key length.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
bss->conf->bssid may be kept unset and will cause an empty BSSID field
in RNR. Fix this to use own_addr instead.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Signed-off-by: moran.daori <moran.daori@celeno.com>
AP as a responder, on successful completion of PASN authentication
configures the required keys by using the command
QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT to the driver.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add an option for an alternative processing of PTKSA life time expiry.
Register a callback in wpa_supplicant to handle the life time expiry of
the keys in PTKSA cache. Send PASN deauthentication when a PTKSA cache
entry expires.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
On successful PASN handshake or 4-way handshake with a peer, PTK is
derived using the local and peer MAC addresses as input. Store the own
MAC address that is used for key derivation in PTKSA cache to maintain
that state over potential MAC addresses changes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use separate capabilities for AP and STA modes for P802.11az security
parameters secure LTF support, secure RTT measurement exchange support,
and protection of range negotiation and measurement management frames
support.
P802.11az security parameters are considered to be supported for both
station and AP modes if the driver sets NL80211_EXT_FEATURE_SECURE_LTF,
NL80211_EXT_FEATURE_SECURE_RTT, and
NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE flags. The driver can
advertize capabilities specific to each mode using
QCA_WLAN_VENDOR_FEATURE_SECURE_LTF*,
QCA_WLAN_VENDOR_FEATURE_SECURE_RTT*, and
QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE* flags.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The new SAE AKM suites are defined to use H2E, so ignore the sae_pwe
value when these AKM suites are used similarly to the way H2E gets
enabled when SAE Password Identifiers are used.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Define new WPA_KEY_MGMT_* values for the new SAE AKM suite selectors
with variable length keys. This includes updates to various mapping and
checking of the SAE key_mgmt values.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Move most of CHANWIDTH_* definitions from ieee80211_defs.h to defs.h as
the definitions are getting used mostly for internal purpose only. Also
change prefix of the definitions to CONF_OPER_CHWIDTH_* and update in
all the files accordingly.
Leave the couple of VHT-specific exceptions to use the old defines (the
reason why they were originally added as VHT values), to avoid use of
clearly marked configuration values in information elements. In
addition, use the defines instead of magic values where appropriate.
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
This information was already available from the nl80211 control port RX
path, but it was not provided to upper layers within wpa_supplicant and
hostapd. It can be helpful, so parse the information from the driver
event.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_validate_wpa_ie() might update sm->* values, so it should not be
allowed for an existing STA entry if that STA has negotiated MFP to be
used for the association. Fix this by first checking whether an SA Query
procedure needs to be initiated. In particular, this prevents a
potential bypass of the disconnection protection.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support for EHT capabilities in the addition of a new station entry
to the driver.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Parse EHT capabilities sent by a non-AP STA in (Re)Association Request
frames. Validate the length of the element, matching MCS rates between
AP TX and STA RX. Store the capabilities in the station info structure.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
