Indicate more clearly when the parsing succeeds to avoid ending the
debug prints with various internal GnuTLS internal error messages even
when the parsing actually succeeded in the end.
Signed-off-by: Jouni Malinen <j@w1.fi>
Replace the internal HMAC MD5, SHA-1, and SHA256 implementations with
the ones from libgcrypt and also add the SHA384 and SHA512 versions.
Signed-off-by: Jouni Malinen <j@w1.fi>
Replace the internal SHA256 implementation with the one from libgcrypt
and also add the SHA384 and SHA512 versions.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a shared helper function instead of implementing practically same
sequence separately for each hash function.
Signed-off-by: Jouni Malinen <j@w1.fi>
The test against use of TKIP was done only in MFP-required
(ieee80211w=2) configuration. Fix this to check the pairwise cipher for
MFP-enabled (ieee80211w=1) case as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd.conf parameter sae_require_pmf=<0/1> can now be used to
enforce negotiation of MFP for all associations that negotiate use of
SAE. This is used in cases where SAE-capable devices are known to be
MFP-capable and the BSS is configured with optional MFP (ieee80211w=1)
for legacy support. The non-SAE stations can connect without MFP while
SAE stations are required to negotiate MFP if sae_require_mfp=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set Sc to 2^16-1 when moving to Accepted state per IEEE Std 802.11-2016,
12.4.8.6.5 (Protocol instance behavior - Confirmed state). This allows
the peer in Accepted state to silently ignore unnecessary
retransmissions of the Confirm message.
Signed-off-by: Jouni Malinen <j@w1.fi>
This implements the behavior described in IEEE Std 802.11-2016,
12.4.8.6.6 (Protocol instance behavior - Accepted state) to silently
discard received Confirm message in the Accepted state if the new
message does not use an incremented send-confirm value or if the special
2^16-1 value is used. This avoids unnecessary processing of
retransmitted Confirm messages.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd.conf parameter sae_sync (default: 5) can now be used to
configure the dot11RSNASAESync value to specify the maximum number of
synchronization errors that are allowed to happen prior to
disassociation of the offending SAE peer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The patch offers alternate implementations of some functions using the
abstract cryptographic API.
This work was done in preparation for the changes to allow hostap to be
compiled with the wolfSSL cryptography and TLS library.
Signed-off-by: Sean Parkinson <sean@wolfssl.com>
This implements crypto_dh_init() and crypto_dh_derive_secret() using
os_get_random() and crypto_mod_exp() for all crypto_*.c wrappers that
include crypto_mod_exp() implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
A new vendor attribute QCA_WLAN_VENDOR_ATTR_GET_WEIGHED_PCL is added for
getting preferred channels with weight value and a flag to indicate how
the channels should be used in P2P negotiation process.
Signed-off-by: Peng Xu <pxu@qti.qualcomm.com>
Indicates the driver to use the RSNE as-is from the connect interface.
Exclusively used for the scenarios where the device is used as a testbed
device with special functionality and not recommended for production.
This helps driver to not validate the RSNE passed from user space and
thus allow arbitrary IE data to be used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously commit c79238b6a4 ('Define a
QCA vendor command to configure SAR Power limits') implemented a vendor
command interface to allow a userspace entity to dynamically control the
SAR power limits. Now implement a command to retrieve the current SAR
power limits.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new disable_fils parameter can be used to disable FILS functionality
in the driver. This is currently removing the FILS Capability bit in
Extended Capabilities and providing a callback to the driver wrappers.
driver_nl80211.c implements this using a QCA vendor specific command for
now.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external programs to get the average channel utilization.
The average channel utilization is calculated and reported through
STATUS command. Users need to configure chan_util_avg_period and
bss_load_update_period in hostapd config to get the average channel
utilization.
Signed-off-by: Bhagavathi Perumal S <bperumal@qti.qualcomm.com>
Recalculate the timeout value for each event instead of calculating this
once and then not allowing the timeout configuration to be changed
without fully stopping and restarting the interface.
This allows the bss_load_update_period configuration parameter to be
modified while a BSS continues operating.
Signed-off-by: Bhagavathi Perumal S <bperumal@qti.qualcomm.com>
Do not update the configuration parameter before having verified the
value to be in the valid range.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
owe_auth_req_process() can return NULL in error cases, but the caller
was not prepared for this. The p pointer cannot be overridden in such
cases since that would result in buffer length (p - buf) overflows. Fix
this by using a temporary variable to check the return value before
overriding p so that the hostapd_sta_assoc() ends up using correct
length for the IE buffer.
Fixes: 33c8bbd8ca ("OWE: Add AP mode handling of OWE with drivers that implement SME")
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The BoringSSL version of crypto_ecdh_init() and dpp_gen_keypair() works
fine with OpenSSL as well, so use that same implementation for both to
avoid unnecessary maintanence of multiple versions.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to go through EC_GROUP_new_by_curve_name(),
EC_KEY_new(), and EC_KEY_set_group() when a single call to
EC_KEY_new_by_curve_name() takes care of all that.
Signed-off-by: Jouni Malinen <j@w1.fi>
This reverts commit 5548453a2d since
BoringSSL added ECDSA_SIG_set0() and ECDSA_SIG_get0() in commit
8dc226ca8f1ef60737e1c1bf8cfcabf51d4068c7 ('Add some missing OpenSSL
1.1.0 accessors.') and updated X509_ALGOR_get0() prototype to match
OpenSSL 1.1.0 changes in commit e3b2a5d30d309091cab3e6a19dee7323c40d968d
('Const-correct X509_ALGOR_get0.').
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows wpa_supplicant configuration with phase1="tls_suiteb=1" to
use openssl_ciphers="ECDHE-RSA-AES256-GCM-SHA384" to further limit the
possible TLS cipher suites when using Suite B with RSA >3K keys. This
combination disables use of DHE and as such, mandates ECDHE to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
These functions are a bit awkward to use for one-off file loads, as
suggested by the tls_clear_default_passwd_cb() logic. There was also
some historical mess with OpenSSL versions and either not having per-SSL
settings, having per-SSL settings but ignoring them, and requiring the
per-SSL settings.
Instead, loading the key with the lower-level functions seems a bit
tidier and also allows abstracting away trying both formats, one after
another.
Signed-off-by: David Benjamin <davidben@google.com>
There's no need to make an extra copy of private_key_passwd for
SSL_{CTX_,}set_default_passwd_cb().
Signed-off-by: David Benjamin <davidben@google.com>
A new vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL is added
for vendor sub-command QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION.
This attribute is for setting the level of WLM.
Signed-off-by: Paul Zhang <paulz@qti.qualcomm.com>
This is needed to allow a credential to be built for GCMP-256/CCMP-256
networks that do not enable GCMP-128/CCMP-128.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the check against WPA/TKIP only configuration by adding CCMP-256
and GCMP-256 to the list of allowed ciphers. This is needed to allow WPS
to be enabled in AP configurations where neither CCMP-128 nor GCMP-128
are enabled.
Signed-off-by: Shiva Sankar Gajula <sgajula@qti.qualcomm.com>
DPP Responder selects whether mutual authentication is used. This commit
adds information about that selection to upper layers (ctrl_iface event
DPP-AUTH-DIRECTION mutual=<0/1>) on the Initiator side.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends dpp_test functionality to allow DPP exchanges to be stopped
when receiving a specified message.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This nl80211 attribute uses NLA_U8 policy in cfg80211 and wpa_supplicant
needs to use same size when writing the attribute.
This fixes mesh mode regression triggered by kernel commit "net:
netlink: Update attr validation to require exact length for some types"
in v4.15-rc1 that resulted in the following debug log entry when trying
to join a mesh:
nl80211: mesh join failed: ret=-22 (Invalid argument)
Fixes: 6c1664f605 ("nl80211: Add new commands to support mesh interfaces")
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This nl80211 attribute uses NLA_U8 policy in cfg80211 and
hostapd/wpa_supplicant needs to use same size when writing the
attribute.
This fixes AP mode regression triggered by kernel commit "net: netlink:
Update attr validation to require exact length for some types" in
v4.15-rc1 that resulted in the following debug log entry when trying to
enable beaconing:
nl80211: Beacon set failed: -34 (Numerical result out of range)
Fixes: da1080d721 ("nl80211: Advertise and configure SMPS modes")
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add QCA vendor command and attributes for vendor specific Representative
RF Operating Parameter (RROP) information. This information is intended
for optional use by external ACS. It provides guidance values for some
RF parameters that are used by the system during operation, so that
external ACS can utilize these to compare between channels, bands, etc.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
One of the event message for TX status was missing 'x' from the "0x"
prefix. Add that to make the used format consistent for all cookie debug
print cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
sha256_vector() result was ignored apart from printing out the failure
in the debug log. This is not really a normal case and it is better to
reject the full operation rather than try to continue with an incorrect
public key hash value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the second json_alloc_token() call failed to allocate memory,
json_parse() missed the first allocation on the error path. Assign the
root pointer earlier for that case to avoid the potential memory leak.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously this stopped only the DPP Authentication instance, but it is
better to clear both PKEX and Authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant was already doing this and hostapd needs to clear
hapd->dpp_auth when completing the exchange in Configurator (GAS server)
role.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
An additional TX status callback could result in processing the DPP
authentication completion another time at least with hostapd. Fix this
by clearing the dpp_auth_ok_on_ack when processing it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for a timeout from an old GAS server operation to
trigger DPP configuration failure during the subsequent DPP operation.
Fix this by verifying that the status callback is for the response
generated during the same DPP Authentication/Configuration exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Configurator signing its own Connector was previously supported only in
wpa_supplicant. This commit extends that to hostapd to allow an AP
acting as a Configurator to self-configure itself.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This moves the Configurator and Bootstrapping Information data from
struct hostapd_data (per-BSS) to struct hapd_interfaces (per-hostapd
process). This allows the information to be maintained over interface
restarts and shared between interfaces.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of using the all-zeros Initiator Bootstrapping Key Hash when no
local bootstrapping key is configuref for the Initiator, automatically
generate a temporary bootstrapping key for the same curve that the
Responder uses. If the Responder indicates that it wants to do mutual
authentication, provide the URI for the auto-generated bootstrapping key
in the DPP-RESPONSE-PENDING event for upper layers to display the QR
Code.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Avoid same interface processing nl80211 events when at least one of
IFIDX, WDEV, or WIPHY index attribute is available in the nl80211 event
message.
Previously, a same interface processes events when ifidx and wdev id
attribute were not available in the nl80211 message. This is extended to
check the presence of wiphy index attribute as well since some radar
notifications include only WIPHY index attrbute in the nl80211 message.
Signed-off-by: Sriram R <srirrama@qti.qualcomm.com>
These allow external programs to determine supported legacy, HT, and VHT
rates of an interface or a STA.
Signed-off-by: Bhagavathi Perumal S <bperumal@qti.qualcomm.com>
If fils_decrypt_assoc() were to fail on the AP side, the previous
implementation could have continued through the response generation
using left = -1. That could have resulted in unexpected processing if
this value were to be used as the length of the remaining (unencrypted)
IEs. Fix this by not updating left in the failure case.
Fixes: 78815f3dde ("FILS: Decrypt Association Request elements and check Key-Auth (AP)")
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that nothing unexpected happened with EAPOL-Key Key MIC
calculation when transmitting EAPOL-Key frames from the Authenticator.
This should not be able to happen in practice, but if if it does, there
is no point in sending out the frame without the correct Key MIC value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 03abb6b541 ('DPP: Reject unexpected
Req/Resp message based on Auth/PKEX role') used incorrect type of error
value (NULL vs. -1). Fix that.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
With the AP proto configured being WPA/RSN and SME in the
driver, the previous implementation in hostapd is to not
process hostapd_notif_assoc() due to "No WPA/RSN IE from STA",
if the (Re)Association Request frame is without the WPA/RSN IEs.
Enhance that to disassociate such station provided the AP is not using
WPS.
Signed-off-by: Hu Wang <huw@codeaurora.org>
This allows external applications to get event indication for Probe
Request frames. Extend ctrl iface cmd "ATTACH" to enable this event on
per-request basis. For example, user has to send ctrl iface cmd "ATTACH
probe_rx_events=1" to enable the Probe Request frame events.
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
If unicast Authentication Request frame is used and the peer ACKs such a
frame, but does not reply within the two second limit, there is no need
to continue trying to retransmit the request frames since the peer was
found, but not responsive.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new conf={sta,ap}-{sae,psk-sae} parameter values can now be used to
specify that the legacy configuration object is for SAE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows DPP to be used for enrolling credentials for SAE networks in
addition to the legacy PSK (WPA-PSK) case. In addition, enable FT-PSK
and FT-SAE cases automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Retransmit the PKEX Exchange Request frame if no response from a peer is
received. This makes the exchange more robust since this frame is sent
to a broadcast address and has no link layer retries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to allow more invalid attribute values to be written
into Peer Discovery Request/Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to cover a case where Config Attrib Object value is
invalid in Configuration Request frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to cover cases where DPP Status value is invalid in
Authentication Response/Confirm frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to cover cases where Initiator/Responder Bootstrap Key
Hash value in DPP Authentication frames is invalid (flip one bit).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends dpp_test to allow invalid Initiator/Responder Protocol Key
to be written into the Authentication Request/Response frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the build include SHA384, use that to derive GTK from GMK. In
addition, add more random bytes bytes to the PRF-X() context data for
longer GTK to reduce dependency on the randomness of the GMK.
GMK is 256 bits of random data and it was used with SHA256, so the
previous design was likely sufficient for all needs even with 128 bits
of additional randomness in GTK derivation. Anyway, adding up to 256
bits of new randomness and using SHA384 can be helpful extra protection
particularly for the cases using GCMP-256 or CCMP-256 as the group
cipher.
Signed-off-by: Jouni Malinen <j@w1.fi>
Unlike OpenSSL, BoringSSL returns an error from
EC_POINT_set_affine_coordinates_GFp() is not on the curve. As such, need
to behave differently here depending on which library is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While the OpenSSL version of i2d_EC_PUBKEY() seemed to be able to use
the POINT_CONVERSION_COMPRESSED setting on the EC key, that did not seem
to work with BoringSSL. Since this is not exactly robust design, replace
use of i2d_EC_PUBKEY() with a custom routine that enforces the DPP rules
on SubjectPublicKeyInfo (compressed format of the public key,
ecPublicKey OID, parameters present and indicating the curve by OID).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This routine was previously implemented twice using i2d_EC_PUBKEY().
There is no need to duplicate that implementation and especially since
it looks like this implementation needs to be replaced for BoringSSL,
start by using a shared helper function for both locations so that there
is only a single place that uses i2d_EC_PUBKEY() to build the special
DPP bootstrapping key DER encoding.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
BoringSSL restored the previously removed AES-192 ECB support in ("Add
AES-192 ECB.") commit. Since this is needed for DPP with the P-384
curve, restore support for this through EVP_aes_192_ecb().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it clearer why some AES operations fail especially with
BoringSSL where the 192-bit case is not supported.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like BoringSSL claims to have OPENSSL_VERSION_NUMBER for a
1.1.0 version, but it does not provide ECDSA_SIG_set0() or
ECDSA_SIG_get0(). For now, add the helper functions regardless of the
version BoringSSL claims to be. Similarly, include the X509_ALGOR_get0()
workaround unconditionally for BoringSSL.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
BoringSSL does not provide some of the OpenSSL API that was used here,
so update this to use similar design to what was already done with DPP
key derivation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like BoringSSL claims to have OPENSSL_VERSION_NUMBER for a
1.1.0 version, but it does not provide SSL_set_default_passwd_cb*(). For
now, comment out this regardless of the version BoringSSL claims to be.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like BoringSSL claims to have OPENSSL_VERSION_NUMBER for a
1.1.0 version, but it does not provide SSL_set1_sigalgs_list(). For now,
comment out this regardless of the version BoringSSL claims to be.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like BoringSSL claims to have OPENSSL_VERSION_NUMBER for a
1.1.0 version, but it does not provide RSA_bits(). For now, add this
backwards compatibility wrapper for BoringSSL regardless of the version
it claims to be.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd configuration parameter group_cipher can now be used to
override the automatic cipher selection based on enabled pairwise
ciphers. It should be noted that selecting an unexpected group cipher
can result in interoperability issues and this new capability is mainly
for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Fix the block comment style issue introduced as part of commit
fbfceef3af ("Add QCA vendor commands for
spectral scan").
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add sub-command QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING to flush
pending packets in firmware. The attributes are listed in enum
qca_wlan_vendor_attr_flush_pending. The QCA_WLAN_VENDOR_ATTR_PEER_ADDR
specifies the peer MAC address and the QCA_WLAN_VENDOR_ATTR_AC specifies
the access category of the pending packets.
Signed-off-by: Lin Tingting <tinlin@qti.qualcomm.com>
A new vendor attribute QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_PENDING_MSDU
is added for vendor sub-command QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET.
This attribute is for pending MSDUs corresponding to respective AC.
Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
This adds support for SAE in AP mode with the atheros driver interface.
EVENT_RX_MGMT includes SAE processing while EVENT_AUTH would require
more changes to make this work.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Undefine the __bitwise macro before defining it to avoid conflicts
with the one from linux/types.h; the same is done some lines above
when __CHECKER__ is defined. Fixes the following warning:
In file included from ../src/l2_packet/l2_packet_linux.c:15:0:
hostap/src/utils/common.h:438:0: warning: "__bitwise" redefined
#define __bitwise
In file included from /usr/include/linux/filter.h:9:0,
from ../src/l2_packet/l2_packet_linux.c:13:
/usr/include/linux/types.h:21:0: note: this is the location of the previous definition
#define __bitwise __bitwise__
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
../src/common/dpp.c: In function 'dpp_test_gen_invalid_key':
../src/common/dpp.c:5531:10: warning: return makes integer from pointer without a cast [-Wint-conversion]
return NULL;
^
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
There should be no wpa_pmk_to_ptk() calls with the cipher argument
indicating a cipher that is not allowed as a pairwise cipher. However,
it looks like that was possible to happen with wlantest. Check for this
corner case explicitly to avoid generating confusing debug logs.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is for protocol testing to check what happens if the Responser
receives an unexpected Authentication Response instead of Authentication
Confirm.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This prevents issues where an unexpected message in the DPP
Authentication exchange or PKEX could result in undefined behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant DPP implementation to retransmit DPP
Authentication Response frame every 10 seconds up to 5 times if the peer
does not reply with DPP Authentication Confirm frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this command stopped listen operation immediately, but if
there was an ongoing authentication exchange, a new listen operation was
started. This is not really expected behavior, so stop the
authentication exchange first with this command to avoid restarting
listen operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new role=either parameter can now be used with DPP_AUTH_INIT to
indicate that the initiator can take either the Configurator or Enrollee
role.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant to iterate over all available channels from
the intersection of what the peer indicates and the local device
supports when initiating DPP Authentication. In addition, retry DPP
Authentication Request frame up to five times if no response is
received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is an initial step in allowing non-operating channel operations
with DPP when hostapd is the Responder. For now, this is only used for
specifying role=configurator/enrollee and qr=mutual cases similarly to
the wpa_supplicant configuration for in Responder role. Request to use a
non-operating channel will be rejected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add the following vendor commands and their vendor attributes for
spectral scan.
1) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG
Get current values of spectral parameters.
2) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS
Get stats for spectral scan debug.
3) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO
Get the spectral hardware capability.
4) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS
Get the current status of spectral scan.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some drivers may accept the remain-on-channel command, but instead of
indicating start event for remain-on-channel, just indicate that the
operation has been canceled immediately. This listen cancel from the
WAIT_PEER_CONNECT state ended up in discontinuation of further
WAIT_PEER_IDLE/WAIT_PEER_CONNECT state transitions. Hence, delay the
subsequent IDLE state by 100 ms.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME
and QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME to record
timestamp and duration for the last MAC counters. Some user layer
application is delay sensitive. It needs to know time stamp and
measurment duration for the counters.
Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
K and z can be derived already based on information available at the
time the PKEX Exchange Request is being processed, so move these there
from the PKEX Commit-Reveal Request processing since that matches the
DPP tech spec description close and allows PKEX exchange to be aborted
earlier if anything unexpected happens.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add limit on number of failed attempts that could have used PKEX code.
If the limit (5) is reached, drop the PKEX state (including the code)
and report this on the control interface to indicate that a new code
needs to be entered due to possible attack.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Clean up the pending PKEX exchange if Commit-Reveal Request processing
indicates a mismatch in the PKEX code. Previously, the this case was
silently ignored and the session was left in pending state that
prevented new PKEX exchanges from getting initated. Now, a new attempt
is allowed to be initiated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Number of places writing BIGNUM values with left-padding were open
coding this helper functionality unnecessarily.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Report mismatching finite cyclic group with PKEX Exchange Response using
STATUS_BAD_GROUP and provide more detailed error report over the control
interface on the peer device when this happens.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The optional channel information was removed from the discovery object
in the DPP tech spec, so no need to maintain this TODO note anymore.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previously used WLAN_REASON_MICHAEL_MIC_FAILURE (14) value as a
response to Authentication frame or (Re)Association Request frame is not
correct since the resp value is encoded in the Status Code (not Reason
Code) field. Status Code 14 is WLAN_STATUS_UNKNOWN_AUTH_TRANSACTION
which is really what this value would have meant in the response frames.
There is no Michael MIC failure status code, so have to use the generic
"Unspecified failure" (1) reason code for these cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up dpp_pkex_rx_commit_reveal_req() a bit and makes it easier
to add protocol testing functionality to PKEX exchange similarly to the
previously added DPP Authentication case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up dpp_pkex_rx_exchange_resp() a bit and makes it easier to
add protocol testing functionality to PKEX exchange similarly to the
previously added DPP Authentication case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up dpp_pkex_rx_exchange_req() a bit and makes it easier to
add protocol testing functionality to PKEX exchange similarly to the
previously added DPP Authentication case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Indicate to upper layers if PKEX Commit-Reveal Request frame AES-SIV
decryption fails. That is a likely sign of the PKEX code mismatch
between the devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Build breakage was introduced by commit
d8afdb210e ('Allow EAPOL-Key messages 1/4
and 3/4 to be retransmitted for testing') for some
CONFIG_TESTING_OPTIONS=y builds without CONFIG_IEEE80211W=y.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
This provides access to the Minimum/Maximum Transmit Power Capabilitie
fileds (the nominal minimum/maximum transmit power with which the STA
is capable of transmitting in the current channel; signed integer in
units of decibels relative to 1 mW).
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
Handle OWE DH exchange and key setup when processing the association
event from a driver that implements AP SME.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While most places using this should be for cases where the hw_features
functionality is required, there seem to be some paths that are getting
exposed in new OWE related operations where that might not be the case.
Add explicit NULL pointer checks to avoid dereferencing the pointer if
it is not set when operating with driver wrappers that do not provide
sufficient information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Normally, WNM-Sleep Mode exit with management frame protection
negotiated would result in the current GTK/IGTK getting added into the
WNM-Sleep Mode Response frame. Some station implementations may have a
vulnerability that results in GTK/IGTK reinstallation based on this
frame being replayed. Add a new hostapd configuration parameter that can
be used to disable that behavior and use EAPOL-Key frames for GTK/IGTK
update instead. This would likely be only used with
wpa_disable_eapol_key_retries=1 that enables a workaround for similar
issues with EAPOL-Key. This is related to station side vulnerabilities
CVE-2017-13087 and CVE-2017-13088. To enable this AP-side workaround,
set wnm_sleep_mode_no_keys=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
When strict group rekeying is in effect, every station that leaves will
cause a rekeying to happen 0.5 s after leaving. However, if a lot of
stations join/leave, the previous code could postpone this rekeying
forever, since it always re-registers the handling with a 0.5 s timeout.
Use eloop_deplete_timeout() to address that, only registering the
timeout from scratch if it wasn't pending.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to test the WoWLAN GTK rekeying KRACK mitigation, add a
REKEY_GTK hostapd control interface command that can be used at certain
points of the test.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the Initiator to request a different channel to be used for DPP
Authentication and DPP Configuration exchanges. This commit adds support
for this in wpa_supplicant with the optional neg_freq=<freq in MHz>
parameter in DPP_AUTH_INIT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Process Authentication Confirm with the two failure cases defined in the
spec: STATUS_NOT_COMPATIBLE and STATUS_AUTH_FAILURE. This verifies the
{R-nonce}k2 part and reports more detailed failure reason if the message
is valid.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If Authentication Response processing fails due to R-capab
incompatibility or R-auth mismatch, send Authentication Confirm with
error status.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the dpp_test mechanism to allow I-nonce, R-capab, R-auth,
and I-auth values in Authentication Response/Confirm to use incorrect
values.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, Initiator decided whether to use mutual authentication on
its own based on having own and peer bootstrapping info. This prevented
Responder from selecting not to use mutual authentication in such a
case. Fix this by allowed Initiator to fall back to non-mutual
authentication based on Responder choice if the bootstrapping mechanism
allows this (PKEX does not; it mandates use of mutual authentication).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the dpp_test mechanism to allow each of the required
attributes in Authentication Confirm to be omitted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the dpp_test mechanism to allow each of the required
attributes in Authentication Response to be omitted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up old dpp_auth_build_resp() (now dpp_auth_build_resp_ok())
a bit by separating initialization steps for a DPP authentication
session from the code needed to build the frame. This allows
dpp_auth_build_resp_status() to share the helper function instead of
having to maintain a duplicated message construction implementation. In
addition, this makes it easier to remove some of the attributes for
protocol testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the dpp_test mechanism to allow each of the required
attributes in Authentication Request to be omitted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up dpp_auth_init() a bit by separating initialization steps
for a DPP authentication session from the code needed to build the
frame. In addition, this makes it easier to remove some of the
attributes for protocol testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Both the DPP-TX and DPP-TX-STATUS events are provided.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that dpp_check_attrs() takes care of verifying that no attributes
are after the Wrapped Data attribute, the duplicated checks in hostapd
and wpa_supplicant side of the implementation can be removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a generic mechanism for configuring the DPP implementation to behave
in particular different (mostly incorrect) ways for protocol testing
purposes. The new dpp_test parameter can be set to a non-zero integer to
indicate a specific behavior. This is only available in
CONFIG_TESTING_OPTIONS=y builds.
This commit include cases for an extra attribute being added after the
Wrapped Data attribute and Initiator/Responder capabilities having an
unexpected zero capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While using an external RADIUS server SUCCESS messages were not being
sent (internal was fine). Also add event messages for other states that
others might find useful, and consistency between the two.
Signed-off-by: Michael Baird <Michael.Baird@ecs.vuw.ac.nz>
Build breakage was introduced by commit
16579769ff ('Add testing functionality for
resetting PN/IPN for configured keys') for some CONFIG_TESTING_OPTIONS=y
builds.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The hostapd bss_transition parameter was previously used to control
advertisement of BSS Transition Management support, but it was not used
when processing BSS Transition Management Query/Response frames. Add an
explicit check during frame processing as well so that any misbehaving
station is ignored. In addition to bss_transition=1, allow mbo=1 to be
used to mark the functionality enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The hostapd wnm_sleep_mode parameter was previously used to control
advertisement of WNM-Sleep Mode support, but it was not used when
processing a request to use WNM-Sleep Mode. Add an explicit check during
request processing as well so that any misbehaving station is ignored.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows hostapd testing functionality to be forced to send out a
plaintext EAPOL-Key frame with the RESEND_* command. That can be useful
in seeing how the station behaves if an unencrypted EAPOL frame is
received when TK is already configured.
This is not really perfect since there is no convenient way of sending
out a single unencrypted frame in the current nl80211 design. The
monitor interface could likely still do this, but that's not really
supposed to be used anymore. For now, clear and restore TK during this
operation. The restore part is not really working correctly, though,
since it ends up clearing the TSC value on the AP side and that shows up
as replay protection issues on the station. Anyway, this is sufficient
to generate sniffer captures to analyze station behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
After an initial connection certain connection parameters may be
updated. It may be necessary to send these parameters to drivers since
these will be used in driver-initiated roaming cases. This commit
defines the driver_ops call for this and implements the needed
functionality for the nl80211 driver interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add additional attributes to specify the PMK, PMKID, and the ERP next
sequence number to the vendor subcommand
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH. These are needed in case
of an offloaded FILS roaming.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes a corner case where RSN pre-authentication candidate from
scan results was ignored if the station was associated with that BSS
just before running the new scan for the connection.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a more accurate scan result age to be fetched than the one
available through NL80211_BSS_SEEN_MS_AGO.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that TK, KCK, and KEK lengths are set to consistent values within
struct wpa_ptk before using them in supplicant. This is an additional
layer of protection against unexpected states.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a new hostapd configuration parameter
wpa_disable_eapol_key_retries=1 that can be used to disable
retransmission of EAPOL-Key frames that are used to install
keys (EAPOL-Key message 3/4 and group message 1/2). This is
similar to setting wpa_group_update_count=1 and
wpa_pairwise_update_count=1, but with no impact to message 1/4
retries and with extended timeout for messages 4/4 and group
message 2/2 to avoid causing issues with stations that may use
aggressive power saving have very long time in replying to the
EAPOL-Key messages.
This option can be used to work around key reinstallation attacks
on the station (supplicant) side in cases those station devices
cannot be updated for some reason. By removing the
retransmissions the attacker cannot cause key reinstallation with
a delayed frame transmission. This is related to the station side
vulnerabilities CVE-2017-13077, CVE-2017-13078, CVE-2017-13079,
CVE-2017-13080, and CVE-2017-13081.
This workaround might cause interoperability issues and reduced
robustness of key negotiation especially in environments with
heavy traffic load due to the number of attempts to perform the
key exchange is reduced significantly. As such, this workaround
is disabled by default (unless overridden in build
configuration). To enable this, set the parameter to 1.
It is also possible to enable this in the build by default by
adding the following to the build configuration:
CFLAGS += -DDEFAULT_WPA_DISABLE_EAPOL_KEY_RETRIES=1
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd control interface commands "RESEND_M1 <addr>" and
"RESEND_M3 <addr>" can be used to request a retransmission of the 4-Way
Handshake messages 1/4 and 3/4 witht he same or modified ANonce (in M1).
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd control interface command "RESEND_GROUP_M1 <addr>" can
be used to request a retransmission of the Group Key Handshake message
1/2 for the current GTK.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of setting the default PMK length for the cleared PMK, set the
length to 0 and explicitly check for this when deriving PTK to avoid
unexpected key derivation with an all-zeroes key should it be possible
to somehow trigger PTK derivation to happen before PMK derivation.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to understand the cases where PMK gets configured
based on information from upper layer call (e.g., a PSK).
Signed-off-by: Jouni Malinen <j@w1.fi>
Currently, reinstallations of the PTK are prevented by (1) assuring the
same TPTK is only set once as the PTK, and (2) that one particular PTK
is only installed once. This patch makes it more explicit that point (1)
is required to prevent key reinstallations. At the same time, this patch
hardens wpa_supplicant such that future changes do not accidentally
break this property.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.
This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.
Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.
Signed-off-by: Jouni Malinen <j@w1.fi>
The driver is expected to not report a second association event without
the station having explicitly request a new association. As such, this
case should not be reachable. However, since reconfiguring the same
pairwise or group keys to the driver could result in nonce reuse issues,
be extra careful here and do an additional state check to avoid this
even if the local driver ends up somehow accepting an unexpected
(Re)Association Response frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation ended up starting a new EAPOL-Key 4-way
handshake if the STA were to attempt to perform another association.
This resulted in immediate disconnection since the PTK was not ready for
configuring FILS TK at the point when EAPOL-Key msg 1/4 is sent out.
This is better than alloing the association to continue with the same TK
reconfigured, but not really ideal.
Address this potential sequence by not starting a new 4-way handshake on
the additional association attempt. Instead, allow the association to
complete, but do so without reconfiguring the TK to avoid potential
issues with PN reuse with the same TK.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows ext_mgmt_frame_handling=1 cases with hostapd to process TX
status events based on external processing. This is useful for increased
test coverage of management frame processing.
Signed-off-by: Jouni Malinen <j@w1.fi>
The driver is expected to not report a second association event without
the station having explicitly request a new association. As such, this
case should not be reachable. However, since reconfiguring the same
pairwise or group keys to the driver could result in nonce reuse issues,
be extra careful here and do an additional state check to avoid this
even if the local driver ends up somehow accepting an unexpected
Reassociation Response frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not try to reconfigure the same TPK-TK to the driver after it has
been successfully configured. This is an explicit check to avoid issues
related to resetting the TX/RX packet number. There was already a check
for this for TPK M2 (retries of that message are ignored completely), so
that behavior does not get modified.
For TPK M3, the TPK-TK could have been reconfigured, but that was
followed by immediate teardown of the link due to an issue in updating
the STA entry. Furthermore, for TDLS with any real security (i.e.,
ignoring open/WEP), the TPK message exchange is protected on the AP path
and simple replay attacks are not feasible.
As an additional corner case, make sure the local nonce gets updated if
the peer uses a very unlikely "random nonce" of all zeros.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Authenticator state machine path for PTK rekeying ended up bypassing
the AUTHENTICATION2 state where a new ANonce is generated when going
directly to the PTKSTART state since there is no need to try to
determine the PMK again in such a case. This is far from ideal since the
new PTK would depend on a new nonce only from the supplicant.
Fix this by generating a new ANonce when moving to the PTKSTART state
for the purpose of starting new 4-way handshake to rekey PTK.
Signed-off-by: Jouni Malinen <j@w1.fi>
Properly track whether a PTK has already been installed to the driver
and the TK part cleared from memory. This prevents an attacker from
trying to trick the client into installing an all-zero TK.
This fixes the earlier fix in commit
ad00d64e7d ('Fix TK configuration to the
driver in EAPOL-Key 3/4 retry case') which did not take into account
possibility of an extra message 1/4 showing up between retries of
message 3/4.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This extends the protection to track last configured GTK/IGTK value
separately from EAPOL-Key frames and WNM-Sleep Mode frames to cover a
corner case where these two different mechanisms may get used when the
GTK/IGTK has changed and tracking a single value is not sufficient to
detect a possible key reconfiguration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Track the current GTK and IGTK that is in use and when receiving a
(possibly retransmitted) Group Message 1 or WNM-Sleep Mode Response, do
not install the given key if it is already in use. This prevents an
attacker from trying to trick the client into resetting or lowering the
sequence counter associated to the group key.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Do not reinstall TK to the driver during Reassociation Response frame
processing if the first attempt of setting the TK succeeded. This avoids
issues related to clearing the TX/RX PN that could result in reusing
same PN values for transmitted frames (e.g., due to CCM nonce reuse and
also hitting replay protection on the receiver) and accepting replayed
frames on RX side.
This issue was introduced by the commit
0e84c25434 ('FT: Fix PTK configuration in
authenticator') which allowed wpa_ft_install_ptk() to be called multiple
times with the same PTK. While the second configuration attempt is
needed with some drivers, it must be done only if the first attempt
failed.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
The new sae_password hostapd configuration parameter can now be used to
set the SAE password instead of the previously used wpa_passphrase
parameter. This allows shorter than 8 characters and longer than 63
characters long passwords to be used. In addition, this makes it
possible to configure a BSS with both WPA-PSK and SAE enabled to use
different passphrase/password based on which AKM is selected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Memory allocation failures could have resulted in error paths that
dereference a NULL pointer or double-freeing memory. Fix this by
explicitly clearing the freed pointer and checking allocation results.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd configuration parameter owe_groups can be used to
specify a subset of the allowed DH groups as a space separated list of
group identifiers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows CONFIG_TESTING_OPTIONS=y builds of wpa_supplicant to
override the OWE DH Parameters element in (Re)Association Request frames
with arbitrary data specified with the "VENDOR_ELEM_ADD 13 <IE>"
command. This is only for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This additional field was added to DPP Public Action frames in DPP tech
spec v0.2.3 to support cryptographic agility in the future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This matches the change in the DPP tech spec to make this less likely to
be confused with the shared secret z.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The owe_transition_bssid and owe_transition_ssid parameters can now be
replace with owe_transition_ifname to clone the BSSID/SSID information
automatically in case the same hostapd process manages both the OWE and
open BSS for transition mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The Key MIC field value got truncated for all cases and incorrect HMAC
hash algorithm was used for the SHA512 cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends OWE support in wpa_supplicant to allow DH groups 20 and 21
to be used in addition to the mandatory group 19 (NIST P-256). The group
is configured using the new network profile parameter owe_group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends OWE support in hostapd to allow DH groups 20 and 21 to be
used in addition to the mandatory group 19 (NIST P-256).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the helper functions for determining OWE key lengths and
Key MIC values to support other DH curves beyond the mandatory group 19.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is not normally done in RSN, but RFC 8110 seems to imply that AP
has to include OWE AKM in the RSNE within these frames. So, add the RSNE
to (Re)Association Response frames when OWE is being negotiated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
sm->pmk_len was not set when deriving the PMK as part of OWE key
generation. This depending on wpa_sm_set_pmk_from_pmksa() call resetting
the value to the default. While this worked for many cases, this is not
correct and can have issues with network profile selection based on
association information. For example, the OWE transition mode cases
would hit an issue here.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new owe_transition_bssid and owe_transition_ssid parameters can be
used to configure hostapd to advertise the OWE Transition Mode element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Replace vendor-specific elements for HE capabilities and HE operation
elements with the P802.11ax defined element values. This version is
based on P802.11ax/D1.4.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These allow external programs to fetch the TX and RX rate information
and signal strength for a specific STA through the hostapd control
interface command "STA <addr>". The values of these attributes are
filled in the response of nl80211 command NL80211_CMD_GET_STATION.
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
Commit 84751b98c1 ('WPS: Allow wildcard
UUID PIN to be used twice') relaxed the constraints on how many time a
wildcard PIN can be used to allow two attempts. However, it did this in
a way that could result in concurrent attempts resulting in the wildcard
PIN being invalidated even without the second attempt actually going as
far as trying to use the PIN and a WPS protocol run.
wildcard_uuid is a flag/counter set for wildcard PINs and it is
incremented whenever the PIN is retrieved by wps_registrar_get_pin().
Eventually it causes the wildcard PIN to be released, effectively
limiting the number of registration attempts with a wildcard PIN.
With the previous implementation, when the PIN is in use and locked
(PIN_LOCKED), it is not returned from wps_registrar_get_pin() but
wildcard_uuid is still incremented which can cause the PIN to be
released earlier and stations will have fewer registration attempts with
it. Fix this scenario by only incrementing wildcard_uuid if the PIN is
actually going to be returned and used.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Add 802.11ax channel property flags for use with external ACS (QCA
vendor command). Use the remaining available bits in
qca_wlan_vendor_channel_prop_flags for the first few 11ax flags. Then
add qca_wlan_vendor_channel_prop_flags_2 as a continuation of
qca_wlan_vendor_channel_prop_flags and add the remaining 11ax flags
there. Note that qca_wlan_vendor_channel_prop_flags_ext is not used
since it is currently not intended for holding such information. Rather
it is meant for holding additional control information related to
features such as DFS, CSA, etc.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
ieee802_1x_kay_decode_mkpdu() calls ieee802_1x_mka_i_in_peerlist()
before body_len has been checked on all segments.
ieee802_1x_kay_decode_mkpdu() and ieee802_1x_mka_i_in_peerlist() might
continue and thus underflow left_len even if it finds left_len to small
(or before checking).
Additionally, ieee802_1x_mka_dump_peer_body() might perform out of bound
reads in this case.
Fix this by checking left_len and aborting if too small early.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
In fils_hlp_finish_assoc() the station is already added to the
driver so it is not needed to check the 'added_unassociated'
flag.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The FILS features on STA needs to be disabled for testing purposes to
verify the APUT behavior with non-FILS STAs. Add a QCA vendor attribute
for doing so.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update these comments based on IEEE Std 802.11-2016 to get rid of the
already resolved TODO comment regarding duplicated N_KEY use. The
implementation does not need any changes since it was already following
the fixed version in the current standard.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add checking for NULL req_ies when FILS processing a driver ASSOC event
in hostapd_notif_assoc(). This was already done in number of old code
paths, but the newer FILS path did not handle this. Though, it is
unlikely that this code path would be reachable in practice since this
is all within sta->auth_alg == WLAN_AUTH_FILS_* check.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Reject a DHE handshake if the server uses a DH prime that does not have
sufficient length to meet the Suite B 192-bit level requirement (<= 3k
(3072) bits).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The hostapd.conf tls_flags=[SUITEB-NO-ECDH] and wpa_supplicant network
profile phase1="tls_suiteb_no_ecdh=1" can now be used to configure Suite
B RSA constraints with ECDHE disabled. This is mainly to allow
the DHE TLS cipher suite to be tested.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Reject a peer certificate chain if it includes an RSA public key that
does not use sufficient key length to meet the Suite B 192-bit level
requirement (<= 3k (3072) bits).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds phase1 parameter tls_suiteb=1 into wpa_supplicant
configuration to allow TLS library (only OpenSSL supported for now) to
use Suite B 192-bit level rules with RSA when using >= 3k (3072) keys.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new psk=<hexdump> can be used as an alternative to pass=<passphrase>
when configuring the DPP Configurator with a legacy network parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These control interface event messages can be used to allow hostapd AP
to be configured for legacy WPA2-Personal configuration with DPP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While the Suite B AKM is not really going to be used with CCMP-128 or
GCMP-128 cipher, this corner case could be fixed if it is useful for
some testing purposes. Allow that special case to skip the HMAC-SHA1
check based on CCMP/GCMP cipher and use the following AKM-defined check
instead.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This part is missing from IEEE Std 802.11ai-2016, but the lack of DHss
here means there would not be proper PFS for the case where PMKSA
caching is used with FILS SK+PFS authentication. This was not really the
intent of the FILS design and that issue was fixed during REVmd work
with the changes proposed in
https://mentor.ieee.org/802.11/dcn/17/11-17-0906-04-000m-fils-fixes.docx
that add DHss into FILS-Key-Data (and PTK, in practice) derivation for
the PMKSA caching case so that a unique ICK, KEK, and TK are derived
even when using the same PMK.
Note: This is not backwards compatible, i.e., this breaks PMKSA caching
with FILS SK+PFS if only STA or AP side implementation is updated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11ai-2016 had missed a change in the Pairwise key hierarchy
clause (12.7.1.3 in IEEE Std 802.11-2016) and due to that, the previous
implementation ended up using HMAC-SHA-1 -based PMKID derivation. This
was not really the intent of the FILS design and that issue was fixed
during REVmd work with the changes proposed in
https://mentor.ieee.org/802.11/dcn/17/11-17-0906-04-000m-fils-fixes.docx
that change FILS cases to use HMAC-SHA-256 and HMAC-SHA-384 based on the
negotiated AKM.
Update the implementation to match the new design. This changes the
rsn_pmkid() function to take in the more generic AKMP identifier instead
of a boolean identifying whether SHA256 is used.
Note: This is not backwards compatible, i.e., this breaks PMKSA caching
based on the initial ERP key hierarchy setup if only STA or AP side
implementation is updated. PMKSA caching based on FILS authentication
exchange is not impacted by this, though.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
secy_init_macsec() can fail (if ->macsec_init fails), and
ieee802_1x_kay_init() should handle this and not let MKA run any
further, because nothing is going to work anyway.
On failure, ieee802_1x_kay_init() must deinit its kay, which will free
kay->ctx, so ieee802_1x_kay_init callers (only ieee802_1x_alloc_kay_sm)
must not do it. Before this patch there is a double-free of the ctx
argument when ieee802_1x_kay_deinit() was called.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Removing interface from bridge in_br
linux_br_del_if(drv->global->ioctl_sock, in_br, ifname)
but in case of failure, the error print is incorrect:
it should show error for "in_br" instead of the wrong bridge name
"brname".
Signed-off-by: Rohit Pratap Singh <rohit.s@samsung.com>
Signed-off-by: Amit Khatri <amit.khatri@samsung.com>
ubsan reported:
../src/crypto/random.c:69:30: runtime error: shift exponent 32 is too large for 32-bit type 'unsigned int'
Explicitly check for the ROL32(x, 0) case which is supposed to be a
no-op.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
After KDF negotiation, must check only requested change occurred in the
list of AT_KDF attributes. If there are any other changes, the peer must
behave like the case that AT_MAC had been incorrect and authentication
is failed. These are defined in EAP-AKA' specification RFC 5448, Section
3.2.
Add a complete check of AT_KDF attributes and send Client-Error if a
change which is not requested is included in it.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sony.com>
AT_KDF attributes need to be included in Synchronization-Failure
according to EAP-AKA' specification RFC 5448.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sony.com>
pmksa_cache_add_entry() may actually free old_entry if the PMKSA cache
is full. This can result in the PMKSA cache containing entries with
corrupt expiration times.
Signed-off-by: Andrew Elble <aweits@rit.edu>
The "FILS: No pending HLP DHCP exchange with hw_addr" debug message was
missing a space before the following MAC address, so add that there to
make the message more readable.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like these parameters related to FT have never been used, so
remove them from causing confusion. The separate update_ft_ies()
callback is used to provide the FT elements.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new sae_commit_override=<hexdump> parameter can be used to force
hostapd to override SAE commit message fields for testing purposes. This
is included only in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow hostapd to be configured to perform SAE reflection attack for SAE
testing purposes with sae_reflection_attack=1 configuration parameter.
This is included only in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add PMKID into EAPOL-Key 1/4 when using SAE and fix the PMK-from-PMKSA
selection in some cases where PSK (from passphrase) could have been
used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was previously defined inconsistently (H() vs. SHA256()), but it is
now clarified in the draft tech spec to use SHA256(), so update
implementation to do that.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
NL80211_ATTR_AUTH_TYPE needs to be skipped if multiple auth_alg options
are included. The previous list missed the new FILS auth_alg here and
ended up not doing so if OPEN and FILS were included.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
DPP tech spec changed the contents of these frames by replacing the
public key hash attributes with a Transaction ID attribute that gets
copied from the request to the response to identify the transaction in a
simpler manner.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use the SSL_get_SSL_CTX() helper instead of dereferencing SSL* since
struct ssl_st is not exposed in public header files anymore.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is an event indicating to the user space that the driver has
detected an internal failure. The driver is expected to recover from
such a failure automatically, e.g., by resetting the device. This event
carries the information indicating the reason that triggered this
detection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previous implementation was able to parse arrays of objects, but not
arrays of other types of items.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The two channel width bits in the VHT capability field can be decoded in
following values (IEEE Std 802.11ac-2013 8.4.2.160.2 VHT Capabilities
Info field):
* 0: no 160 or 80+80 MHz support
* 1: 160 MHz support
* 2: 160 and 80+80 MHz support
* 3: (reserved)
The check must therefore not be done bitwise but instead it must checked
whether the capabilities announced by the driver are at least the ones
requested by the user.
Fixes: c781eb8428 ("hostapd: Verify VHT capabilities are supported by driver")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Previously, CONFIG_WNM enabled build that supports WNM for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode WNM is required and there is no need for AP mode WNM.
Add support to differentiate between station mode WNM and AP mode
WNM in wpa_supplicant builds by adding CONFIG_WNM_AP that should be
used when AP mode WNM support is required in addition to station mode
WNM. This allows binary size to be reduced for builds that require
only the station side WNM functionality.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
X509_ALGOR_get0() was modified to use const ** pointer as the first
argument in OpenSSL 1.1.0, so need to use different type here to avoid
compilation issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the pointer to strdup passwd was left in OpenSSL library
default_passwd_cb_userdata and even the default_passwd_cb was left set
on an error path. To avoid unexpected behavior if something were to
manage to use there pointers, clear them explicitly once done with
loading of the private key.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since OpenSSL version 1.1.0f, SSL_use_PrivateKey_file() uses the
callback from the SSL object instead of the one from the CTX, so let's
set the callback on both SSL and CTX. Note that
SSL_set_default_passwd_cb*() is available only in 1.1.0.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Add a build option to select different default ciphers for OpenSSL
instead of the hardcoded default "DEFAULT:!EXP:!LOW".
This new option is useful on distributions where the security level
should be consistent for all applications, as in Fedora [1]. In such
cases the new configuration option would be set to "" or
"PROFILE=SYSTEM" to select the global crypto policy by default.
[1] https://fedoraproject.org/wiki/Changes/CryptoPolicy
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Add OCE IE in Beacon, Probe Response, and (Re)Association Response
frames if OCE is enabled in the configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Check if device supports OCE STA/STA-CFON/AP specific mandatory
features. This commit includes checking based on the QCA vendor
attributes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This request ID was wrongly referred from the REQUEST_ID in
enum qca_wlan_vendor_attr_gscan_config_params which is mapped to
QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM in PNO Config.
Hence define a different attribute to represent the request ID
for PNO Config.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In case of incorrect HT40 configuration as part of an attempt to create
a 80 MHz AP, iface->conf->vht_oper_centr_freq_seg0_idx and
iface->conf->vht_oper_centr_freq_seg1_idx are zero'ed, but
iface->conf->vht_oper_chwidth remains VHT_CHANWIDTH_80MHZ. This causes
the logic in dfs_get_start_chan_idx to fail.
Fix this by setting iface->conf->vht_oper_chwidth to
VHT_CHANWIDTH_USE_HT when zero'ing the center frequency parameters.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
dpp.h file requires openssl in order to compile, which breaks
compilation on systems without it.
Move DPP_OUI_TYPE to ieee802_11_defs.h and don't include dpp.h when
not really needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add changes to control interface command get_capability to advertize
FILS capability, FILS AKMs suites, and FILS Authentication algorithms
based on the driver capabilities.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The attribute is QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE, not
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd did not add a new PMKSA cache entry when FILS shared key
authentication was used, i.e., only the initial full authentication
resulted in a PMKSA cache entry being created. Derive the PMKID for the
ERP case as well and add a PMKSA cache entry if the ERP exchange
succeeds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The EAP message included in FILS Wrapped Data from the non-AP STA to the
AP is EAP-Initiate/Re-auth.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The DPP Configurator can use this new command to generate its own signed
connector for the network that it manages.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the hostapd control interface to support the
DPP_BOOTSTRAP_INFO command that was recently added for wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The default value for GTK rekeying period was previously hardcoded to
600 seconds for all cases. Leave that short value only for TKIP as group
cipher while moving to the IEEE 802.11 default value of 86400 seconds
(once-per-day) for CCMP/GCMP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This updates the previously copied implementation to be up-to-date with
the more recent wpa_supplicant changes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow hostapd to initiate and respond with PKEX bootstrapping similarly
to how this was implemented in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These need to be compatible for the JWS protected header signing to be
valid, so add an explicit check to confirm this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of trying to share the existing definitions for NIST curves,
start using unique strings for Brainpool curves.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements genric PKEX functionality in src/common/dpp.c and glue
code to use this in wpa_supplicant (i.e, hostapd DPP implementation does
not yet support PKEX).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use helper functions to cover all three different hash algorithm options
for DPP operations instead of having separate calls to each function at
every location a hash operation based on the curve is needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to notice a reason for failure in cases a connector
string has been truncated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This function is used for parsing both the C-sign-key and netAccessKey,
so better not imply that all cases are C-sign-key in the debug prints.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Set temporary disallowed BSSID list to the driver so that the driver
doesn't try to connect to any of the blacklisted BSSIDs during
driver-based roaming operation. This commit includes support only for
the nl80211 driver interface using a QCA vendor command for this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
ERP key was previously derived immediately after the availability of
EMSK and Session-Id and the ERP key hierarchy was saved even if the
authentication resulted in failure eventually. Instead, derive the ERP
key only after a successful EAP authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS to specify
the active Type Of Service on the specific interface. This can be used
to modify some of the low level scan parameters (off channel dwell time,
home channel time) in the driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
New AKM suites like FILS-SHA256 do not use KCK and hence KCK length can
be zero. Add changes to include KCK attribute in rekey data only if the
length is non-zero.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can now be configured to generate a network profile
automatically based on DPP configuration. The following
dpp_config_processing values can be used to specify the behavior:
0 = report received configuration to an external program for
processing; do not generate any network profile internally (default)
1 = report received configuration to an external program and generate
a network profile internally, but do not automatically connect
to the created (disabled) profile; the network profile id is
reported to external programs
2 = report received configuration to an external program, generate
a network profile internally, try to connect to the created
profile automatically
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend hostapd configuration to include parameters needed for the DPP
AKM: dpp_connector, dpp_netaccesskey, dpp_netaccesskey_expiry,
dpp_csign, dpp_csign_expiry.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external programs to generate and add PMKSA cache entries
into hostapd. The main use for this is to run external DPP processing
(network introduction) and testing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds DPP bootstrapping, authentication, and configuration into
hostapd similarly to how the design was integrated in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for DPP Configuration Protocol using GAS. Full
generation and processing of the configuration object is not included in
this commit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add wpa_supplicant control interface commands for parsing the bootstrap
info URI from a QR Code (get peer public key) and to generate a new
bootstrap info with private key for local use. The optional
key=<hexdump> argument to the DPP_BOOTSTRAP_GEN command can be used to
specify the bootstrapping private key in OpenSSL ECPrivateKey DER
encoding format. This results in the local bootstrapping information
entry being created with the specified key instead of generating a new
random one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Introduction of the new base64 helper function changed the backtraces
for these OOM test cases and resulted in test failures. Update the test
scripts to work with the new implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The additional SHA-384 and SHA-512 functionality is needed to support
DPP with various ECC curves.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the eap_proxy mechanism to be used with multiple SIMs by
following the configured sim_num to index which SIM to use for when
fetching the IMSI through eap_proxy.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
For proxy based EAP methods, the EAP identity is constructed in
eap_proxy layer from IMSI when required. Realm information from identity
is used to do ERP eventually, hence construct the realm for proxy based
methods from IMSI in core wpa_supplicant to enable the ERP use case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant tries to reinitialize an interface when a previously
removed netdev is restored (e.g., re-insert a USB dongle). If that
initialization fails (e.g., driver ejects ifconfig UP), the previous
implementation resulted in leaving the interface in incomplete state
while still claiming to upper layers that the interface status has
changed back to functional one.
Fix this by skipping the interface status update if reinitialization
fails. In other words, remain in INTERFACE_DISABLED state if the
interface cannot be re-enabled successfully.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds support for deriving ERP key information in EAP Proxy
based EAP method implementations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd processes a received 20/40 BSS Coexistence management frame, but
if no separate callbacks are registered for handling Public Action
frames it eventually sends a reply with MSB of category code set to 1
thinking that the received frame is an invalid frame. This could happen
based on whether hostapd was built and enabled with functionality using
the callback functions.
Fix this by explicitly returning 1 from the function when the 20/40 BSS
Coexistence Management frame is processed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new acs_exclude_dfs=1 parameter can be used to request hostapd to
exclude all DFS channels from ACS consideration. This is mainly of use
for cases where the driver supports DFS channels, but for some reason a
non-DFS channel is desired when using automatic channel selection.
Previously, the chanlist parameter could have been used for this, but
that required listing all the acceptable channels. The new parameter
allows this to be done without such a list.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit renames the vendor attribute
QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_OFFCHANNEL to
QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL as intended by the
original commit d506c35efc ('Set Wi-Fi
Configuration attribute to restrict offchannel operations').
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit defines an attribute to
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION -
QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL which can be used to
restrict offchannel operations on the AP/GO interface.
The goal is to restrict any operations which would cause the AP/GO to
leave its operating channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds changes to not generate ERP information if the domain
name is not specified in the EAP identity. keyName-NAI needs the realm
part and as such, it is reasonable to require the main EAP configuration
to provide that realm.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 3e0272ca00 ('nl80211: Re-read MAC
address on RTM_NEWLINK') added the detection of external changes to MAC
address when the interface is brought up.
If the interface state is changed quickly enough, wpa_supplicant may
receive the netlink message for the !IFF_UP event when the interface
has already been brought up and would ignore the next netlink IFF_UP
message, missing the MAC change.
Fix this by also reloading the MAC address when a !IFF_UP event is
received with the interface up, because this implies that the
interface went down and up again, possibly changing the address.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
This is to comply with uniform spreading requirement for ETSI domain
(section 4.7.2.7 in EN 301 893 - V1.8.1). ETSI uniform spreading
requires equal probability for the usable channels. The previous channel
selection logic after a radar detection did not fully comply with the
uniform spreading requirement for the domain by ignoring DFS channels.
Consider DFS channels also during channel selection when the current DFS
domain is ETSI.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Current DFS domain information of the driver can be used in ap/dfs
to comply with DFS domain specific requirements like uniform spreading
for ETSI domain.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
This commit introduces the following two attributes to
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH events:
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS - Indicates the status of
re-association requested by user space
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION - Indicates whether
the old association was maintained when a re-association
is requested by user space and that re-association attempt
fails (i.e., cannot connect to the requested BSS, but can
remain associated with the BSS with which the association was
in place when being requested to roam).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit defines an attribute
QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL which allows the currently
used listen interval to be updated using
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION. This update applies
only during the association and is done without updating the AP about
the change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only SHA1 hash -based server certificate matching was used,
but the OCSP response may use SHA256 instead of SHA1, so check the match
with both hash functions, if needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only SHA1 hash -based server certificate matching was used,
but the OCSP response may use SHA256 instead of SHA1, so check the match
with both hash functions, if needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In some practical cases, it is useful to suppress joining to node in the
distance. The new field mesh_rssi_threshold could be used as RSSI
threshold for joining.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This needs to allow all 20 MHz channel numbers to be converted even
though the Annex E table lists only channel _center_ frequencies 50 and
114. Neighbor Report (see IEEE Std 802.11-2016, 9.4.2.37 Neighbor Report
element) uses Channel Number field with "last known primary channel of
the AP" which refers to the 20 MHz channel and not the channel center
frequency.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Derive PMK-R0 and the relevant key names when using FILS authentication
for initial FT mobility domain association.
Signed-off-by: Jouni Malinen <j@w1.fi>
Derive PMK-R0 and the relevant key names when using FILS authentication
for initial FT mobility domain association. Fill in the FT IEs in
(Re)Association Request frame for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends fils_pmk_to_ptk() to allow FILS-FT to be derived. The
callers do not yet use that capability; i.e., actual use will be added
in separate commits.
Signed-off-by: Jouni Malinen <j@w1.fi>
The conditional gSTA and gAP (DH public keys) were not previously
included in Key-Auth derivation, but they are needed for the PFS case.
Signed-off-by: Jouni Malinen <j@w1.fi>
The conditional gSTA and gAP (DH public keys) were not previously
included in Key-Auth derivation, but they are needed for the PFS case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add support to set ignore assoc disallow to the driver so that the
driver ignores assoc disallowed bit set by APs while connecting. This is
used by drivers that handle BSS selection and roaming internally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Enable use of FT RRB without configuring each other AP locally. Instead,
broadcast messages are exchanged to discover APs within the local
network.
When an R0KH or R1KH is discovered, it is cached for one day.
When a station uses an invalid or offline r0kh_id, requests are always
broadcast. In order to avoid this, if r0kh does not reply, a temporary
blacklist entry is added to r0kh_list.
To avoid blocking a valid r0kh when a non-existing pmk_r0_name is
requested, r0kh is required to always reply using a NAK. Resend requests
a few times to ensure blacklisting does not happen due to small packet
loss.
To free newly created stations later, the r*kh_list start pointer in
conf needs to be updateable from wpa_auth_ft.c, where only wconf is
accessed.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This adds a counter and adds sequence numbering to FT RRB packets. The
sequence number is checked against r0kh/r1kh sequence number cache.
Special attention is needed in case the remote AP reboots and thus loses
its state. I prefer it to recover automatically even without synchronized
clocks. Therefore an identifier called dom is generated randomly along the
initial sequence number. If the dom transmitted does not match or the
sequence number is not in the range currently expected, the sender is asked
for a fresh confirmation of its currently used sequence numbers. The packet
that triggered this is cached and processed again later.
Additionally, in order to ensure freshness, the remote AP includes an
timestamp with its messages. It is then verified that the received
messages are indeed fresh by comparing it to the older timestamps
received and the time elapsed since then. Therefore FT_RRB_TIMESTAMP is
no longer needed.
This assigns new OUI 00:13:74 vendor-specific subtype 0x0001 subtypes:
4 (SEQ_REQ) and 5 (SEQ_RESP).
This breaks backward compatibility, i.e., hostapd needs to be updated
on all APs at the same time to allow FT to remain functional.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Convert FT RRB into a new TLV based format. Use AES-SIV as AEAD cipher
to protect the messages.
This needs at least 32 byte long keys. These can be provided either
by a config file change or letting a KDF derive the 32 byte key used
from the 16 byte key given.
This breaks backward compatibility, i.e., hostapd needs to be updated on
all APs at the same time to allow FT to remain functional.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Replace the previously used extension of IEEE 802.11 managed Ethertype
89-0d (originally added for Remote Request/Response in IEEE 802.11r)
with Ethertype 88-b7 (OUI Extended EtherType) for FT inter-AP
communication. The new design uses a more properly assigned identifier
for the messages.
This assigns the OUI 00:13:74 vendor-specific subtype 0x0001 for the new
hostapd AP-to-AP communication purposes. Subtypes 1 (PULL), 2 (RESP),
and 3 (PUSH) are also assigned in this commit for the R0KH-R1KH
protocol.
This breaks backward compatibility, i.e., hostapd needs to be updated on
all APs at the same time to allow FT to remain functional.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The check for erp->keyname_nai within eap_erp_get_key() is apparently
too difficult for some static analyzers to notice. Add an explicit check
for os_strchr() return value being non-NULL to avoid false reports.
Signed-off-by: Jouni Malinen <j@w1.fi>
These functions can potentially be called with ie == NULL and ie_len ==
0. Check explitcitly for the ie == NULL case to avoid confusing
memcpy(dst, NULL, 0) calls.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 941caed980 ('MBO: Add MBO
ANQP-element processing on AP') changed the design by using the
rx_anqp_vendor_specific() function to process all ANQP vendor specific
elements. However, the caller for this was within ifdef CONFIG_HS20
block. Fix this by calling the function even in CONFIG_HS20=y is not
included in the build. This fixes CONFIG_MBO=y builds without
CONFIG_HS20=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
When starting AP in HT40 mode and both HT40+ and HT40- options are
specified in hostapd.conf, select a valid secondary channel for the AP
automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a string "FILS_HLP_SENT" to connect event when HLP is sent
as part of ASSOC/CONNECT request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
ieee802_1x_kay_move_live_peer() did not check
ieee802_1x_kay_get_potential_peer() result explicitly and a static
analyzer reported a warning about the possible NULL result. This cannot
really happen in practice since the only caller of
ieee802_1x_kay_move_live_peer() verifies that the specific peer entry is
available. Anyway, it is easy to silence the false warning by adding an
explicit check here and cover any other potential case if another caller
is added.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow this function to be called from outside ieee802_11.c and with the
final steps replaced through a callback function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This function does not need the frame header, so pass in only the IE
area to make it easier to share this for driver-based AP SME handling.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is used with partial AP SME in driver cases to enable FILS
association (AES-SIV) processing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to allow the driver SME to perform the needed AES-SIV
operations during FILS association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to add more parameters without having to change the
callback function prototype.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This will be used to determine what type of operations to use for STA
authentication and association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit defines an attribute
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to signify the preferred
channel list policy for external ACS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the uuid configuration parameter is not set, wpa_supplicant generates
an UUID automatically to allow WPS operations to proceed. This was
previously always using an UUID generated from the MAC address. This
commit adds an option to use a random UUID instead. The type of the
automatically generated UUID is set with the auto_uuid parameter: 0 =
based on MAC address (default; old behavior), 1 = random UUID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While responding to EAPOL-Key message 1/2 with EAPOL-Key message 2/2
when using FILS AKM suites the ENCRYPTED bit is not set in key info of
2/2 which causes AP to drop 2/2. Fix this by setting the ENCRYPTED bit
since FILS AKM based connection uses AEAD encryption/decryption.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
GTK rekeying was rejected if a prior 4-way handshake is not done.
Fix this by allowing GTK rekey to happen in case of a FILS connection
since it does not involve a 4-way handshake.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new PMKSA cache entry within wpa_supplicant if a driver event from
offloaded FILS shared key authentication indicates a new PMKSA entry was
created.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update the internal fils_completed state when offloading FILS shared key
authentication to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows ERP keys to be managed by external entities, e.g., when
offloading FILS shared key authentication to a driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for setting and deleting PMKSA cache entries based on FILS Cache
Identifer. Also additionally add support for sending PMK as part of
SET_PMKSA to enable driver to derive keys in case of FILS shared key
offload using PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed for configuring PMKSA cache entries to the driver with
the FILS Cache Identifier and SSID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for FILS shared key offload for drivers which advertize
FILS shared key support using NL80211_CMD_CONNECT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add new vendor commands for starting and stoppping spectral scan. Add
vendor attributes for configuring spectral scan parameters as part of
the start command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
MDE was already added with RSNE, but FTE needed to be added to the FILS
Authentication frame for the FT initial mobility domain association
using FILS authentication case.
Signed-off-by: Jouni Malinen <j@w1.fi>
When using FILS for FT initial mobility domain association, add MDE to
the Authentication frame from the STA to indicate this special case for
FILS authentication.
Signed-off-by: Jouni Malinen <j@w1.fi>
The last SD Response frame fragment is not going to be followed by
another Action frame from the peer, so remove the 200 ms wait time from
the offchannel TX command in that case. This avoids leaving a 200 ms
lock on the radio to remain on the channel unnecessarily.
This is similar to commit 7655bd7388
('P2P: Do not use wait_time for SD Response TX without fragmentation').
Signed-off-by: Jouni Malinen <j@w1.fi>
With AP-AP communication, when hapd0 sends a packet, hapd1 can receive
it immediately and send a response. But hapd0 will only read and process
the response after it has returned from the sending context, that is
entered eloop again. So one does not need to consider the RX function of
the reply to run for the request sending hapd before the send calling
function has returned.
Previously, with intra-process communication, the packet is not
scheduled through eloop. Thus the RX handler of the reply might be run
while the sending context of the original request has not returned.
This might become problematic, e.g., when deferring a management frame
processing until an RRB response is received and then have the request
restarted and finished before the original request handling has been
stopped.
I'm not aware of any concrete bug this is currently triggering but came
across it while thinking of FT RRB AP-AP sequence numbering.
I think the non-eloop scheduling approach might be error-prone and thus
propose to model it more closely to the way the message would be
received from a socket. Additionally, this ensures that the tests model
AP-AP communication more closely to real world.
Solution: queue these packets through eloop.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
With multiple interface like AP and station which is already
associated to some other AP, when we try to do channel switch
for the AP mode (different from the operation channel support of
station) and if the AP channel switch fails continously (including
the fallback channel switch), results in a crash due to NULL pointer
dereference. This is because hostapd_deinit_driver() assigns the
driver context (drv_priv) to NULL as we are not able to bring up
the interface with a new channel
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Add attribute for TA max duration after last TA received. So that local
time is synchromous to other communicating OCB STAs. If the duration
expires, OCB STA without UTC time source is not in sync to other STAs
and stop scheduling DSRC channel switch after max duration.
Signed-off-by: Zhaoyang Liu <zhaoyang@codeaurora.org>
Signed-off-by: Ferry Zhou <tianguiz@codeaurora.org>
Document QCA vendor OCB commands about IEEE Std 802.11 communication
outside the context of a basic service set. Also define all attributes
for the specific OCB commands.
Signed-off-by: Zhaoyang Liu <zhaoyang@codeaurora.org>
Signed-off-by: Ferry Zhou <tianguiz@codeaurora.org>
This change fixes the following compilation error:
wpa.c:2465: error: undefined reference to 'crypto_ecdh_deinit'
in builds where CONFIG_ECC does not get defined.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes the following compiler warning:
wpa_auth.c:4249:34: error: address of array 'a->conf.fils_cache_id'
will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not accept a link-local IPv4 address when waiting for a valid DHCP
address. This helps with hs20-osu-client use cases where DHCP response
has not yet been received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the Value node was not added if value of a node could not be
fetched. This can cause interoperability issues, so address that in the
same way as an empty length value, i.e., by adding a Value node with
zero-length contents.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In case wpa_supplicant is using driver_macsec_linux, but macsec module
is not (yet) loaded in the kernel, nl_socket_alloc() fails and drv->sk
is NULL. In this case, don't call libnl functions rntl_link_add() or
rtnl_link_change() using such NULL pointer, to prevent program from
getting segmentation faults like:
Program received signal SIGSEGV, Segmentation fault.
nl_socket_get_local_port (sk=sk@entry=0x0) at socket.c:365
365 if (sk->s_local.nl_pid == 0) {
(gdb) p sk
$1 = (const struct nl_sock *) 0x0
(gdb) bt
#0 nl_socket_get_local_port (sk=sk@entry=0x0) at socket.c:365
#1 0x00007ffff79c56a0 in nl_complete_msg (sk=sk@entry=0x0,
msg=msg@entry=0x55555595a1f0) at nl.c:491
#2 0x00007ffff79c56d1 in nl_send_auto (sk=sk@entry=0x0,
msg=msg@entry=0x55555595a1f0) at nl.c:522
#3 0x00007ffff79c652f in nl_send_sync (sk=sk@entry=0x0,
msg=0x55555595a1f0) at nl.c:556
#4 0x00007ffff755faf5 in rtnl_link_add (sk=0x0,
link=link@entry=0x55555595b0f0, flags=flags@entry=1024) at route/link.c:1548
#5 0x000055555567a298 in macsec_drv_create_transmit_sc (priv=0x55555593b130,
sc=0x55555593b320, conf_offset=<optimized out>) at ../src/drivers/driver_macsec_linux.c:998
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
ieee802_1x_kay_deinit_transmit_sc() frees the transmit secure channel
data, but secy_delete_transmit_sc() still needs it. Since this functions
are called sequentially, secy_delete_transmit_sc() can be called from
ieee802_1x_kay_deinit_transmit_sc() before txsc is freed.
Fixes: 128f6a98b3 ("mka: Fix the order of operations in secure channel deletion")
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
ieee802_1x_kay_deinit_receive_sc() frees the receive secure channel data,
but secy_delete_receive_sc() still needs it. Since these two functions
are always called sequentially, secy_delete_receive_sc() can be called
from ieee802_1x_kay_deinit_receive_sc() before rxsc is freed.
Fixes: 128f6a98b3 ("mka: Fix the order of operations in secure channel deletion")
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
1. Add new attribute to report corresponding antenna information to the
chain RSSI which is used in subcmd
QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI.
2. Add a series of attr to support the new wmi interface
WMI_PDEV_PARAM_ANT_DIV_USRCFG which export parameters setting of antenna
diversity algorithm to userspace.
Signed-off-by: Li Feng <lifeng@qti.qualcomm.com>
QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY is added to set
propagation delay's absolute value. This is a more detailed version of
QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY.
Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
If a P2P_FIND command is issued for running the initial full scan and
the attempt to start that full scan fails, the previous behavior was to
wait for the ongoing scan to complete and then continue p2p_find scan
iterations. However, this continued with the social channels scan
instead of the initial full scan. This could end up missing the full
scan completely.
Fix this by marking the full scan pending if the new scan cannot be
started immediately. Then start the initial full scan after the ongoing
scan completes before moving to social channel only scan iterations.
This applies both for the P2P_FIND_START_WITH_FULL (no specific
frequency set) and P2P_FIND_PROGRESSIVE cases since both of them start
with a single full scan round.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the "P2P_FIND freq=<MHz>" operation more robust by continuing
to include the specified frequency in the consecutive scan rounds
instead of including it only once in the first scan. In other words, the
first scan is only for the specified frequency just like the previous
behavior, but the following scans include all the social channels and
the specified frequency instead of just the previously used social
channels.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds an option to configure wpa_supplicant to use the perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime network profile parameter fils_dh_group is used to enable
this by specifying which DH group to use. For example, fils_dh_group=19
would use FILS SK PFS with a 256-bit random ECP group.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds an option to configure hostapd to enable use of perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime configuration parameter fils_dh_group is used to enable this
by specifying which DH group to use. For example, fils_dh_group=19 would
allow FILS SK PFS to be used with a 256-bit random ECP group.
Signed-off-by: Jouni Malinen <j@w1.fi>
draft-harkins-owe-07.txt does not specify these parameters, so need to
pick something sensible to use for the experimental implementation. The
Suite B 128-bit level AKM 00-0F-AC:11 has reasonable parameters for the
DH group 19 case (i.e., SHA256 hash), so use it for now. This can be
updated if the OWE RFC becomes clearer on the appropriate parameters
(KEK/KCK/MIC length, PRF/KDF algorithm, and key-wrap algorithm).
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds STA side addition of OWE Diffie-Hellman Parameter element into
(Re)Association Request frame and processing it in (Re)Association
Response frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds AP side processing for OWE Diffie-Hellman Parameter element in
(Re)Association Request frame and adding it in (Re)Association Response
frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
The KDF define in RFC 5295 is very similar to HKDF-Expand() defined in
RFC 5869. Allow a NULL label to be used to select the RFC 5869 version
with arbitrary seed (info in RFC 5869) material without forcing the
label and NULL termination to be included. HKDF-Expand() will be needed
for OWE.
Signed-off-by: Jouni Malinen <j@w1.fi>
These allow ECDH to be used with compressed public key encoding (only
x-coordinate). This is needed for FILS PFS and OWE.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a helper function that parses candidate list from command line
arguments.
This function will be used (in the following commits) to add
a candidate list to BSS transition management query.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This extends the GAS/ANQP parser in wpa_supplicant to process MBO
ANQP-elements and indicate received Cellular Data Connection Preference
values over the control interface.
When a valid MBO ANQP-element is received, the following control
interface message is sent:
RX-MBO-ANQP <BSSID> cell_conn_pref=<value>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the GAS server to process MBO ANQP-elements and reply to a
query for the Cellular Data Connection Preference (if configured). The
new configuration parameter mbo_cell_data_conn_pref can be used to set
the value (0, 1, or 255) for the preference to indicate.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
MBO techspec v0.0_r27 changed the MBO ANQP-element format. The MBO
element in ANQP query should now include an MBO Query List element that
contains a list of MBO elements to query.
Add API to add the MBO Query List to an ANQP query.
Format:
ANQP_GET <addr> <info_id>[,<info_id>]...[,mbo:<subtype>...]
Example for querying neighbor report with MBO cellular data
connection preference:
ANQP_GET <bssid> 272,mbo:2
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
As FCC DFS requirement does not explicitly mention about the validity of
the (pre-)CAC when channel is switched, it is safe to assume that the
pre-CAC result will not be valid once the CAC completed channel is
switched or radar detection is not active on the (CAC completed) channel
within a time period which is allowed (10 seconds - channel switch time)
as per FCC DFS requirement.
Use the new driver event to allow the driver to notify expiry of the CAC
result on a channel. Move the DFS state of the channel to 'usable' when
processing pre-CAC expired event. This means any future operation on
that channel will require a new CAC to be completed. This event is
applicable only when DFS is not offloaded to the kernel driver.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Process the new nl80211 event NL80211_RADAR_PRE_CAC_EXPIRED to allow the
driver to notify expiry of the CAC result on a channel.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
When DFS channel state is shared across multiple radios on the system it
is possible that a CAC completion event is propagated from other radio
to us. When in enabled state, do not proceed with setup completion upon
processing CAC completion event with devices where DFS is not offloaded,
when in state other than enabled make sure the configured DFS channel is
in available state before start the AP.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
The userspace may want to delay the the first scheduled scan.
This enhances sched_scan to add initial delay (in seconds) before
starting first scan cycle. The driver may optionally choose to
ignore this parameter and start immediately (or at any other time).
This uses NL80211_ATTR_SCHED_SCAN_DELAY to add this via user
global configurable option: sched_scan_start_delay.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This leads to cleaner code overall, and also reduces the size
of the hostapd and wpa_supplicant binaries (in hwsim test build
on x86_64) by about 2.5 and 3.5KiB respectively.
The mechanical conversions all over the code were done with
the following spatch:
@@
expression SIZE, SRC;
expression a;
@@
-a = os_malloc(SIZE);
+a = os_memdup(SRC, SIZE);
<...
if (!a) {...}
...>
-os_memcpy(a, SRC, SIZE);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be used to clean the code and reduce size by converting
os_malloc() followed by os_memcpy() cases to use a single function call.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add driver interface command using the QCA vendor extensions to check
the driverr whether to accept or reject a BSS transition candidate. For
the reject case, report an MBO reject reason code.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
radius_server_session_free() does not remove the session from the
session list and these radius_server_get_new_session() error paths ended
up leaving a pointer to freed memory into the session list. This
resulted in the following operations failing due to use of freed memory.
Fix this by using radius_server_session_remove() which removes the entry
from the list in addition to calling radius_server_session_free().
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible to hit a double-free on the l2_packet socket if
initialization of DHCP/NDISC snoop failed on a hostapd interface that
had previously had those enabled successfully. Fix this by clearing the
l2_packet pointers during deinit.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT for setting the number
of antennas that will be active in different modes for each connection.
Signed-off-by: Alexei Avshalom Lazar <qca_ailizaro@qca.qualcomm.com>
Define a new attribute QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH.
This attribute can set a station device to work in 5 or 10 MHz channel
width while in disconnect state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd.conf parameter country3 can now be used to configure the
third octet of the Country String that was previously hardcoded to ' '
(= 0x20).
For example:
All environments of the current frequency band and country (default)
country3=0x20
Outdoor environment only
country3=0x4f
Indoor environment only
country3=0x49
Noncountry entity (country_code=XX)
country3=0x58
IEEE 802.11 standard Annex E table indication: 0x01 .. 0x1f
Annex E, Table E-4 (Global operating classes)
country3=0x04
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When ASLR is enabled, like it is by default on many distros now,
the trace code doesn't work right.
Fix this by looking up the start of the executable mapping and
subtracing it from all the lookups.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
CONFIG_TLS=linux can now be used to select the crypto implementation
that uses the user space socket interface (AF_ALG) for the Linux kernel
crypto implementation. This commit includes some of the cipher, hash,
and HMAC functions. The functions that are not available through AF_ALG
(e.g., the actual TLS implementation) use the internal implementation
(CONFIG_TLS=internal).
Signed-off-by: Jouni Malinen <j@w1.fi>
These operations may fail with some crypto wrappers, so allow the
functions to report their results to the caller.
Signed-off-by: Jouni Malinen <j@w1.fi>
When getting the channel number from a frequency, all supported modes
should be checked rather than just the current mode. This is needed when
hostapd switches to a channel in different band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The __FAVOR_BSD macro was previously used in netinet/udp.h to select
between two different names of the variables in struct udphdr. Define
that to force the versions with the uh_ prefix. In addition, use the
same style consistently within fils_hlp.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new broadcast_deauth parameter can be used to disable sending of the
Deauthentication frame whenever AP is started or stopped. The default
behavior remains identical to the past behavior (broadcast_deauth=1).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 01e2231fdc ('hostapd: Skip some
configuration steps for mesh cases') removed some operations based on
hapd->iface->mconf being NULL. This was within #ifdef CONFIG_MESH, so it
should not impact hostapd, but it can impact AP mode with
wpa_supplicant. That does not sound intentional, so make these
conditional on hapd->conf->mesh being enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows PMKSA cache entries for FILS-enabled BSSs to be shared
within an ESS when the BSSs advertise the same FILS Cache Identifier
value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The RSN supplicant implementation needs to be updated to use the new
BSSID whenever doing FILS authentication. Previously, this was only done
when notifying association and that was too late for the case of
reassociation. Fix this by providing the new BSSID when calling
fils_process_auth(). This makes PTK derivation use the correct BSSID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows PMKSA cache entries to be shared between all the BSSs
operated by the same hostapd process when those BSSs use the same FILS
Cache Identifier value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The correct order of deleting a secure channel is to purge all the
secure associations in the channel before actually deleting the secure
channel.
Signed-off-by: Badrish Adiga H R <badrish.adigahr@gmail.com>
The RSN pre-authentication case ended up ignoring the initial
startPeriod value and delayed EAPOL-Start message by two seconds. Fix
this by forcing the first EAPOL-Start message to be sent when running
pre-authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds reason for timeout in event CTRL-EVENT-ASSOC-REJECT whenever
connection failure happens because of timeout. This extends the
"timeout" parameter in the event to include the reason, if available:
timeout=scan, timeout=auth, timeout=assoc.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE 802.11ax HE changes to include HE IEs in Beacon and Probe Response
frames. These elements are using vendor specific forms for now since the
IEEE 802.11ax draft is not yet finalized and the element contents is
subject to change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add IEEE 802.11ax definitions for config, IEEE structures, and
constants. These are still subject to change in the IEEE process.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Let mesh STA A be a STA which has config disable_ht=0 and disable_vht=1.
Let mesh STA B be a STA which has config disable_ht=0 and disable_vht=0.
The mesh STA A and B was connected.
Previously, the mesh STA A sent frame with VHT rate even though its VHT
was disabled. This commit fixes the issue by checking the local BSS VHT
configuration.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Let mesh STA A be a STA which has config disable_ht=1.
Let mesh STA B be a STA which has config disable_ht=0.
The mesh STA A and B was connected.
Previously, the mesh STA A sent frame with HT rate even though its HT
was disabled. This commit fixes the issue by checking the local BSS HT
configuration.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This function is called only from locations within ifdef
CONFIG_EAP_PROXY, so there is no need to try to cover the not-defined
case here and the function can simply be removed completely if
CONFIG_EAP_PROXY=y is not used.
Signed-off-by: Jouni Malinen <j@w1.fi>
This debug print can include GTK and IGTK, so use wpa_hexdump_key()
instead of wpa_hexdump() for it to avoid undesired exposure of keys in
debug log.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While the FILS authentication cases were already using the proper PMK
length (48 octets instead of the old hardcoded 32 octet), the initial
association case had not yet been updated to cover the new FILS SHA384
AKM and ended up using only a 32-octet PMK. Fix that to use 48-octet PMK
when using FILS SHA384 AKM.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
sha384_prf() is used both with Suite B and FILS, so add CONFIG_FILS as
another alternative to building in this functionality.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a copy of the internal HMAC-SHA256 implementation with the hash
block size and output length updated to match SHA384 parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
The output length was incorrect (32 from the copy-pasted SHA256
version). Fix this to return the correct number of octets (48) for
SHA384. This fixes incorrect key derivation in FILS when using the
SHA384-based AKM.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
HTTP response was previously sent as a plaintext without the HTTP header
on port 12345. By default Android webview/Chrome assumes plaintext as
HTTP/0.9 data. Android webview/Chrome has removed support of HTTP/0.9
request/response on non-standard ports, i.e., other than port 80. This
results in error while opening URL 'http://localhost:12345/'.
Fix this by prefixing the HTTP response with the HTTP/1.1 header.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously the peer operating channel preference was accepted if the
indicated frequency was listed in the local preference list from the
driver. This was assuming that the driver included only channels that
are currently enabled for GO operation. Since that might not be the
case, filter the local preference list by doing an explicit validation
of the indicated channels for P2P support.
This moves the similar validation steps from two other code paths in
p2p_check_pref_chan_recv() and p2p_check_pref_chan_no_recv() into a
common filtering step in p2p_check_pref_chan() for all three cases.
This avoids issues to start the GO in cases where the preferred
frequency list from the driver may include channels that are not
currently enabled for P2P GO use (e.g., 5 GHz band in world roaming
configuration).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new P2P_SET parameter uses <op_class>:<channel> format and is used
mainly for testing purposes to allow overriding the value of the GO
Negotiation Response frame Operating Channel attribute.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, any potential (even if very unlikely) local operation error
was ignored. Now these will result in aborting the negotiation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The url argument to ieee802_11_send_bss_trans_mgmt_request() was
hardcoded to NULL in the only caller, so this code cannot be reached.
wnm_send_bss_tm_req() construct the same frame with more generic
parameters, including option for including the URL, so
ieee802_11_send_bss_trans_mgmt_request() can be simplified.
Signed-off-by: Jouni Malinen <j@w1.fi>
The length of the WNM-Sleep element was not verified before using it.
This could result in reading the subfields in this element (total of
four octets) beyond the end of the buffer. Fix this by ignoring the
element if it is not long enough to contain all the subfields.
Signed-off-by: Jouni Malinen <j@w1.fi>
The struct wpa_stsl_negotiation seemed to have been for some kind of
tracking of state of PeerKey negotiations within hostapd. However,
nothing is actually adding any entries to wpa_auth->stsl_negotiations or
using this state. Since PeerKey does not look like something that would
be deployed in practice, there is no justification to spend time on
making this any more complete. Remove the dead code now instead of
trying to figure out what it might be used for.
Signed-off-by: Jouni Malinen <j@w1.fi>
