This adds a test case for the server fragmenting an EAP-IKEv2 message.
In addition, the fragmentation threshold is made shorter to trigger
fragmentation for all messages.
Signed-off-by: Jouni Malinen <j@w1.fi>
The BSS id numbers were assumed to start from 0 at the beginning of this
test case, but that is only the case if this is run as the first test
after starting wpa_supplicant. Fix the test case to figure out the id
values dynamically to avoid false errors.
Signed-off-by: Jouni Malinen <j@w1.fi>
Extend EAP-SIM/AKA/AKA' test coverage by setting up another
authentication server instance to store dynamic SIM/AKA/AKA' information
into an SQLite database. This allows the stored reauth/pseudonym data to
be modified on the server side and by doing so, allows testing fallback
from reauth to pseudonym/permanent identity.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows control interface issues to be caught in a bit more readable
way in the debug logs. In addition, dump pending monitor socket
information more frequently and within each test case in the log files
to make the output clearer and less likely to go over the socket buffer
limit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the scan to miss a Probe Response frame especially
under heavy load, so try again to avoid reporting invalid failures.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for a scan to fail to see Probe Response or Beacon frame
under heavy load (e.g., during a parallel-vm.sh test run) since the
dwell time on a chanenl is quite short. Make the test cases using
INTERWORKING_SELECT more robust by trying again if the first attempt
does not find a matching BSS.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for the final step of the test case to fail under load
(e.g., when using parallel-vm.sh with large number of VMs), so run
through additional scan iterations if the WPS-AUTH flag does not get
removed immediately.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that AP acts on 40 MHz intolerant STA association/disassociation
and on 20/40 co-ex report indicating 40 MHz intolerant AP showed up and
removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It turned out that the initial test case found the GO based on the
initial full scan instead of the progressive search part. Fix this by
started the GO only after the initial full scan.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can fail if Probe Response frame is missed and Beacon frame was
used to fill in the BSS entry. This can happen, e.g., during heavy load
every now and then and is not really an error, so try to workaround by
runnign another scan.
Signed-off-by: Jouni Malinen <j@w1.fi>
It seems like it is possible for a CTRL-EVENT-REGDOM-CHANGE event from a
previous test case to "leak" through to the execution of this test case.
That can result in the validation steps here failing, so wait a bit and clear the pending events before starting the test.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_multi_bss_acs test case was failing if it was executed immediately
after a test case that used 5 GHz band since the current mac80211_hwsim
channel survey implementation is very limited and reports only a single
channel. For this test case, that channel has to be from the 2.4 GHz
band.
Signed-off-by: Jouni Malinen <j@w1.fi>
run-tests.py now takes an optional --long parameter that can be used to
enable running of test cases that take a long time (multiple minutes).
By default, such test cases are skipped to avoid making the normal test
run take excessive amounts of time.
As an initial long test case, verify WPS PBC walk time expiration (two
minutes).
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not report missing PBC overlap detection as an issue in this test
case since the sequence can miss the overlap due to per-SSID scan used
during group formation. In addition, increase AP beaconing frequency to
make it more likely for a Beacon frame to be seen during the optimized
scan.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds some helper definitions and functions to allow cfg80211 to be
tested with raw nl80211 messages built in the test scripts. The first
test case shows a case where station disassociates instead of
deauthenticates (which is the wpa_supplicant behavior).
Signed-off-by: Jouni Malinen <j@w1.fi>
These are similar to the previous cases, but with supported rate set
limited to allow the BSS membership selector to fit into that element
instead of Ext Supp Rates.
Signed-off-by: Jouni Malinen <j@w1.fi>
The 5 GHz cases are not yet complete due to missing mac80211_hwsim
functionality. The current test cases allow the ACS operation to fail
for those cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies P2P Client scanning behavior during group re-invocation in
a case where old scan results are not available to allow the scan to be
skipped completely.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Wait for the AP to be ready before initiating the scan to avoid
unnecessary five second extra wait. In addition, disconnect the station
to avoid possibility of starting a new scan at the end of the test case.
These remove unnecessary wait time from the test cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
"parallel-vm.sh <number of VMs> [arguments..]" can now be used to run
multiple VMs in parallel to speed up full test cycle significantly. In
addition, the "--split srv/total" argument used in this design would
also make it possible to split this to multiple servers to speed up
testing.
Signed-off-by: Jouni Malinen <j@w1.fi>
The optional third argument to the test case functions can now be used
to receive additional parameters from run-tests.py. As the initial
parameter, logdir value is provided so that test cases can use it to
review the debug logs from the test run.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previusly, the responding device was left in p2p_find state as a
consequence of using discover_peer() if the peer was not already known.
This was not the sequence that was supposed to be used here. Go to
listen-only state when waiting for the peer to initiate a previously
authorized GO Negotiation.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was found through a mac80211 bug which didn't correctly accept a
center segment 0 value of zero, so the test will fail until the mac80211
bug is fixed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows a critical error to be noticed more quickly and reported
more clearly in the test log.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some kernel debugging options (especially
CONFIG_DEBUG_KOBJECT_RELEASE=y) can add significant blocking time to
interface removal with NL80211_CMD_DEL_INTERFACE and
SIOCGIFBR(BRCTL_DEL_BRIDGE) block for 1-8 seconds. This could result in
the VLAN test cases failing due to a wpaspy timeout on the REMOVE
command even though the issue was only in the kernel debugging code
making the operations significantly slower. Work around this by using a
longer timeout for that control interface command to allow this type of
debug kernel to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If trace-cmd command does not exist, run-tests.py could end up hanging
in a loop waiting for input. Fix this simply by checking whether the
trace-cmd command can be executed sucessfully and exiting the script if
not.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
Both the output file path and the current working directory included the
log directory and this failed if log directory was not absolute (e.g.,
when using the default logs/current in the case a VM is not used).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The return value was lost and GCMP, CCMP-256, and GCMP-256 test cases
were reporting PASS instead of SKIP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that session information is stored from Access-Accept and sent to
the station at the requested timeout. Verify that station processes this
notification.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that hostapd can add extra RADIUS attributes using
radius_auth_req_attr and radius_acct_req_attr.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Fix updating of the current symbolic link when LOGDIR is already set.
The current symbolic link was only set, if LOGDIR has not been
previously defined. If the user had chosen to cancel the running test
iteration and run it again by running start.sh again, the current
symbolic link was not updated.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
This commit includes number of test frames for attribute parsing.
Invitation Request and Provision Discovery processing is also covered.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is the older design that some drivers may still use if they do not
support offloaded offchannel TX operations.
Signed-off-by: Jouni Malinen <j@w1.fi>
A bit different code path is used to match the first three different
locations of roaming consortium OI within Beacon frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait a bit between WPS_CONFIG command and the first scan. This can avoid
an extra five second wait due to having to scan again if the initial
scan operations happens to be quick enough to happen before the AP has
updated its configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that 'INTERWORKING_SELECT auto' is able to pick the
correct network based on priority configuration when connected to a
lower priority network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
test_ap_hs20_multi_cred_sp_prio verifies that two credentials
provisioned by a single SP are selected properly based on sp_priority
when a single BSS matches both credentials.
test_ap_hs20_multi_cred_sp_prio2 does the same when there a separate BSS
for each credential.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that 'INTERWORKING_SELECT auto' is able to roam to a
higher priority network when executed while connected to a lower
priority network.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a new option to set the use_chanctx flag when creating a radio.
While at it, refactor the arguments parsing code to use argparse.
Signed-hostap: Luciano Coelho <luciano.coelho@intel.com>
This seems to be needed in some cases to avoid issues in test cases that
assume there are no other ERs running.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the script check the environment for the current python
interpreter in use instead of assuming that the python executable points
to a python 2 interpreter.
Signed-off-by: Roger Zanoni <roger.zanoni@openbossa.org>
Only run-tests.py is actually executed, so there is no need to specify
the interpreter in all the helper files and test script files.
Signed-off-by: Jouni Malinen <j@w1.fi>
CONFIG_MODULE_TESTS=y build option can now be used to build in module
tests into hostapd and wpa_supplicant binaries. These test cases will be
used to get better testing coverage for various details that are
difficult to test otherwise through the control interface control. A
single control interface command is used to executed these tests within
the hwsim test framework. This commit adds just the new mechanism, but no
module tests are yet integrated into this mechanism.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify cases both with multiple peers (one of which not advertising any
services) and with multiple SD queries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like some of the discovery_* test cases have been failing every
now and then on the virtual server and the one second timeout could have
been a bit too short to cover some possible timing cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Enable hostapd control interface for the RADIUS server instance and
verify that the RADIUS server MIB counters are incremented.
Signed-off-by: Jouni Malinen <j@w1.fi>
This improves accuracy of the code coverage reports with hostapd-as-AS
and hlr_auc_gw getting analyzed separately.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a password that uses one, two, and three octet encoding
for UTF-8 characters. The value is tested against a pre-configured
hash to verify that utf8_to_ucs2() function works correctly.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like get_status() has failed in some test runs because of a
STATUS command returning an line without '=' on it. Instead of stopping
there on exception, report the unexpected line in the log and ignore it
to allow test to continue.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that NFC connection handover can be used in a case where
hostapd has an enabled password token.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that PD Request followed by GO Negotiation Request is enough to
learn the Listen frequency of the peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
To test the code under the influence of time jumps, add the option
(--timewarp) to the VM tests to reset the clock all the time, which
makes the wall clock time jump speed up 20x, causing gettimeofday()
to be unreliable for timeout calculations.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Since wlantest is a separate process that is not synchronized with rest
of the test components, there can be some latency in it having the STA
entries and counters updated. There is a race condition between this
happening and then test script clearing or fetching data. Make this race
condition less likely to cause bogus test failures by adding some wait
between these operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
In addition to running the FLUSH command again, the pending monitor
interface events need be cleared in case the driver was running a scan
when reset() is called. This avoids issues, e.g., with discovery_dev_id
failing due to an unexpected P2P-DEVICE-FOUND event that was generated
by the pending scan operation that had not yet complete when the first
dump_monitor() call in reset() happened.
Signed-hostap: Jouni Malinen <j@w1.fi>
The vm-config in the subdirectory is less useful as it
will get removed by "git clean" and similar, so read a
config file from ~/.wpas-vm-config in addition.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It looks like slow virtual machines may have issues to complete some EAP
authentication cases (e.g., EAP-EKE in ap_ft_eap) within the 10 second
timeout under load. Double the timeout to avoid incorrect test failures.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the previous test case to leave unexpected BSS or
P2P peer table entries if a scan was in progress when the FLUSH command
was used. This could result in test failures, e.g., when running
discovery_dev_type_go followed by discovery_group_client where a P2P
peer was discovered on another channel at the end of the former test
case from a scan that was running durign the FLUSH operation that was
supposed to remove all P2P peers. This could result in
discovery_group_client failing due to dev[2] trying to send the
discoverability frame on incorrect channel (the one learned in the
previous test case) since discover_peer() skipped a new device
discovery. Fix this by running FLUSH operation again if a pending scan
operation is detected during the first FLUSH operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In addition, add the earlier tests in the new test_ssid.py file that was
forgotten from the previous commit
d78f33030d.
Signed-hostap: Jouni Malinen <j@w1.fi>
WPS-ER-AP-REMOVE event from the ER is sent before HTTP UNSUBSCRIBE has
been completed. As such, it was possible for the following scan
validation step to be started before the AP has had a chance to react to
the ER status change. Makes this less likely to fail by waiting 200 ms
before starting the last scan.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was possible for the AP to report two enrollees in this test case
(i.e., both the expected wlan1 device and also the ER device on wlan0).
The previous test script would fail if the wlan0 device is reported
first. Fix this by allowed the expected target to be found in either the
first or the second WPS-ER-ENROLLEE-ADD event.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was possible for this test case to fail if P2P_FLUSH was issued
during a search scan and that scan adding back the peer. Avoid this by
forcing p2p_find to be started regardless of the current P2P peer table
contents for each round of service discovery.
Signed-hostap: Jouni Malinen <j@w1.fi>
With the extra latencies removed from run-tests.py operations, it was
possible to hit race conditions in pairwise cipher configuration at the
end of the 4-way handshake. In some cases, the EAPOL-Start frame from
the station was not received by the AP and that could result in these
test cases failing. Since there are not really trying to test the race
condition, wait for the AP side to complete key configuration prior to
initiating the reauthentication sequence.
Signed-hostap: Jouni Malinen <j@w1.fi>
When a thread is used to follow P2P group formation progress, it is
better to return a clear failure indication from the thread instead of
allowing an exception to be thrown from the thread.
Signed-hostap: Jouni Malinen <j@w1.fi>
Leave couple of cases to use full scan for better test coverage, but
change all other places to use a single channel scan with
INTERWORKING_SELECT to reduce the time it takes to execute the tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is possible that wlantest has not yet created the BSS entry in all
cases, so interpret failures (no BSS entry being the most likely cause)
as zero counters. Similarly, ignore clear_bss_counters errors since they
are most likely reporting that the BSS was not found and as such, there
was no need to clear the counters anyway.
Signed-hostap: Jouni Malinen <j@w1.fi>
The FLUSH command clears disallow_aps, p2p_disabled, and
p2p_per_sta_psk, so there is no need to clear them separately.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace the fixed 100 ms waits with a select()-based wait and timeout
for full wait based on monotonic time to optimize wait_event().
Signed-hostap: Jouni Malinen <j@w1.fi>
Do not run a full scan in gas_generic since this is not really needed.
Dump pending event messages after long wait to make logs clearer.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it easier to build a web page for analyzing failures without
having to fetch the log files themselves from the test server.
Signed-hostap: Jouni Malinen <j@w1.fi>
No need to run a full scan as the first step since it only needs to find
the AP from a known channel for the GAS operation.
Signed-hostap: Jouni Malinen <j@w1.fi>
Now that wpa_supplicant requests the driver (cfg80211) to clear its scan
cache automatically after each BSS_FLUSH/FLUSH command, the previously
used ignore_old_scan_res workaround should not be needed for the hwsim
test cases anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is not really perfect, but something to get a bit more testing
coverage.. For proper discoverability mechanism validation, the P2P
client would need to go to sleep to avoid acknowledging the GO
Negotiation Request frame. Offchannel Listen mode operation on the P2P
Client with mac80211_hwsim is apparently not enough to avoid the
acknowledgement on the operating channel, so need to disconnect from the
group which removes the GO-to-P2P Client part of the discoverability
exchange in practice.
Signed-hostap: Jouni Malinen <j@w1.fi>
These were somewhat more hidden to avoid direct use, but there are now
numerous places where these are needed and more justification to make
the extern int declarations available from wpa_debug.h. In addition,
this avoids some warnings from sparse.
Signed-hostap: Jouni Malinen <j@w1.fi>
It did not look like open mode association completed with WEXT.. I'm
commenting that test case out for now since WPA2-PSK worked. If you care
about WEXT, feel free to fix it and submit a patch to remove the
"REMOVED_" prefix here..
Signed-hostap: Jouni Malinen <j@w1.fi>
Add test cases to use connect command instead of auth+assoc commands and
AP mode operations using the old monitor interface design.
Signed-hostap: Jouni Malinen <j@w1.fi>
The actual data connection does not seem to work with mac80211_hwsim, so
the hwsim_test results are ignored for now.
Signed-hostap: Jouni Malinen <j@w1.fi>
NOTE: Actual use of the direct link (DLS) is not supported in
mac80211_hwsim, so this operation fails at setting the keys after
successfully completed 4-way handshake. This test case does allow the
key negotiation part to be tested for coverage, though.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was previously not obvious from the <test case>.log file that a test
case was marked failed based on kernel issues. Make this very clear to
avoid wasting time on figuring out what caused the failure.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use a more robust design for collecting the gcov logs from the case
where test cases are run within a virtual machine. This generates a
writable-from-vm build tree for each component separately so that the
lcov and gcov can easily find the matching source code and data files.
In addition, prepare the reports automatically at the end of the
vm-run.sh --codecov execution.
Signed-hostap: Jouni Malinen <j@w1.fi>
It takes some time for hostapd to complete AP startup. In some cases,
this could potentially result in station starting a scan before the AP
is beaconing or ready to reply to probes. To avoid such race conditions,
wait for AP-ENABLED before going ahead with the test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it easier to enable various testing parameters and
functionality in build configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds number of test cases to go through various possible EAP
configurations for Interworking network selection.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since the venue information in the Interworking element is optional,
include both the cases of it included and not included in the test
cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
This verifies that IP packets with various DSCP values are mapped to the
correct TID both with default mapping and with custom QoS mappings.
Signed-hostap: Jouni Malinen <j@w1.fi>
In order to handle regulatory domain requests, crda needs to be
installed on the host, but we also need to install a uevent helper in
the VM so that it gets executed (since we don't run udev).
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This verifies that QoS Map configuration and update can be completed.
Actual QoS mapping for Data frames within mac80211/cfg80211 is not yet
verified.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there's code coverage analysis data, copy it out of the VM
to be able to analyse it later. Also add a description to the
README file about how to use it.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
These were not really used in practice and better quality test cases for
concurrent P2P operations are now available in tests_p2p_concurrency.py
using the standard test framework design. Remove the special concurrent
option for start.sh and the run-all.sh concurrent and
concurrent-valgrind operations to clean up scripts.
Signed-hostap: Jouni Malinen <j@w1.fi>
This extends P2P test coverage to include the case of separate group
interface use with autonomous GO and group formation through GO
negotiation.
Signed-hostap: Jouni Malinen <j@w1.fi>
Lockdep complaints are never good, so check for them in the
kernel messages, not just for warnings and bugs.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
There's no reason to format the failed tests as a python
list, just print a (space-separated) list of test names.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This allows the build.sh script to be used to rebuild binaries based on
existing configuration in addition to the initial case of preparing
suitable build configuration.
Signed-hostap: Jouni Malinen <j@w1.fi>
LOGDIR directory is created automatically if LOGDIR variable was not
set. If the variable is set, that directory is expected to exist.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_supplicant configuration files had a hardcoded GROUP=admin. The
start.sh script failed on a system without admin group (some systems
have it named adm).
Generate configuration files with appropriate GROUP in the log dir
and use them.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Add a CHANNELS configuration to the script running the VM
that can be added to the vm-config file to allow running
the tests with hwsim devices supporting more than a single
channel.
Eventually, with the (hopefully) upcoming dynamic work in
mac80211_hwsim, this might go away entirely, but for now
this allows testing more code paths.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
These verify that hostapd is able to remove a BSS while the radio is
still in the progress of the initial channel parameter determination.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since removal of the primary BSS is now going to remove all the BSSs
for a radio, these two test cases need changes to not trigger false
failures.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Catch exceptions from operations that try to remove hostapd interface
and rename the log file. If these operations fail due to socket
connection issues, hostapd has likely died or gotten stuck somewhere.
Report the test case as a failure and stop test run cleanly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These are still disabled by default since they require mac80211_hwsim
changes that are not yet in the upstream kernel and because the test
cases do not fully work yet. Anyway, they are quite convenient for
development use, so good to have them available in the main repository.
Signed-hostap: Jouni Malinen <j@w1.fi>
This extends the Hostapd class to support monitor interface events and
STATUS command similarly to the WpaSupplicant class so that internal
hostapd state can be verified in more detail.
Signed-hostap: Jouni Malinen <j@w1.fi>
Verify that a single configuration file can be used to initiate multiple
BSSes in hostapd and that these BSSes can then be dynamically removed.
Signed-hostap: Jouni Malinen <j@w1.fi>
This fixes the user.key file (incorrect key was copied previously) and
adds a test case for EAP-TLS with WPA2-Enterprise.
Signed-hostap: Jouni Malinen <j@w1.fi>
This increases EAP method coverage for WPA2-Enterprise to include
EAP-pwd, EAP-GPSK, EAP-SAKE, EAP-EKE, EAP-IKEv2, EAP-PAX, and EAP-PSK.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to request the previously used default behavior where
the devices are not stopped at the end of a test case if a single test
case is run.
Signed-hostap: Jouni Malinen <j@w1.fi>
Verify that hostapd handles ENABLE command on invalid configuration
correctly and allows the configuration to be fixed or the interface to
be removed.
Signed-hostap: Jouni Malinen <j@w1.fi>
Remove the -l command like option from run-tests.py and always enable
writing of debug level logs to files. The stdout debug verbosity is
controlled independently of the debug log files.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is needed to avoid invalid PBC session overlap detection when
the previous test case used active PBC mode and the old BSS entry
in cfg80211 may still be valid when starting the next test case.
Signed-hostap: Jouni Malinen <j@w1.fi>
A full scan in these specific test cases does not add anything to the
coverage, so use a single channel scan for the station connection to
remove undesired extra time needed for a full scan.
Signed-hostap: Jouni Malinen <j@w1.fi>
This optional argument can be used to randomize the order in which the
test cases are run. This can provide more coverage on testing
interactions of common use cases in various different sequences. Such
issues have already been found even with the fixed order of test cases,
but being able to reorder the tests makes this more efficient.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is easier than to copy/paste from the README. We may
want to extend it later to change the .config for some
common differences between systems (e.g., libnl/libbfd).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, e.g., with the VM tests if the VM crashes, it
can be useful to know which tests should have run but didn't
(or didn't finish). In order to catch these more easily, add
an option to prefill the database with all tests at the very
beginning of the testing (in a new NOTRUN state) and use the
option in the VM tests.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Create a results.db in the output directory when running
the tests in a VM. To make that easier, create the tables
in the python script if they don't exist.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Refactor the test reporting to treat the different results
(success/skip/failure) identically. This makes the timing
seem a bit longer, but cleans up the code which will allow
for adding more checks (e.g., on the captured data files)
later.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Rather than just having KERNELDIR, allow setting KERNEL directly.
Also remove the -s option that prevents running multiple machines
at the same time, but add a KVMARGS= variable that can be used to
restore that if needed.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
test_ap_bss_add_remove verifies hostapd behavior when BSSes are
added/removed in multi-BSS configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows run-tests.py to use the same logs/<date> default logdir as
start.sh which is quite convenient for manual test runs.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The run-tests.py -l argument does not take an argument value anymore.
Instead, debug output is directed to a separate file <test>.log for each
test case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is unnecessary extra complexity for user, so use the 'test_' prefix
only internally within the python scripts and file names.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is unnecessary extra complexity for user and reports, so use the
'test_' prefix only internally within the python scripts.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to run a separate tcpdump process to capture frames
from hwsim0 since wlantest is already doing that can write the results
to a file.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This file was used for adding debug info into the buildbot logs. The new
sqlite database-based design will replace that, so there is no need to
create last-debug and getting rid of it will make it easier to split the
run log into per-test case files.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 781b65cfbb ended up accidentally
changing this from an integer to a string. Fix this by not converting
the variable into a string.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of running on the host, it can be useful to run in a
VM, particularly to test kernel rather than userspace changes,
so add a few scripts that allow doing so easily.
The basic idea is that the VM kernel is the same architecture
as the host kernel, so the host's root filesystem can be used
(in read-only mode) to run everything. Only a log filesystem
is mounted read-write and will get all the test output.
The kernel console output is collected to a special 'console'
file in the logs directory and kernel crashes are detected.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
If running in a VM with the logs going to a host filesystem
chown isn't actually possible, silence any warnings from it.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Resetting at the beginning causes the reset logging/tracing
data to leak from the previous test into the next, and the
last one being missed at all - reset at the end of each run
instead. Also reset before all tests just in case running a
test actually crashed the python script.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
In addition to tracing, allow collecting dmesg. There's no
provision for actually looking at it and finding problems
in it yet though.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Instead of passing the log directory for each option
(-l, -r, -e, and -T) pass it once and make the other
options just take the filename (optionally, even).
This will also make it easier to extend later.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Instead of logging many files called "<timestamp>-*", log into
a new "<timestamp>/*" in the logs/ subdirectory and only put
the last-debug file into logs/. If a LOGDIR is specified in the
environment, instead just put everything into that directory
(so the caller should make sure to give it a timestamp or so)
and skip the creation of last-debug entirely.
Also clean up a bit and pass the LOGDIR from run-all.sh to
start.sh rather than having start.sh create the timestamp and
run-all.sh detect the latest one when having run start.sh.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
In order to get tracing per test, allow run-tests.py to start
and stop tracing per test case. This is implemented using a
python 'with' context so it starts/stops automatically at the
right spots.
Instead of starting global tracing, also use it from run-all.sh
and put the trace files into the log dir.
Note that this only works right if you use a separate log dir
for all test runs as the trace files aren't timestamped.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Just like wpa_supplicant, give hostapd the -T option to
send all debug messages into the Linux tracing buffer.
Enable this option for hwsim test builds by default.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Allow run-all to pass on extra arguments from the command
line that aren't built by the script itself.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Reuse the code rather than duplicating the implementation
of starting the tests. To make that easier, allow passing
multiple modules with -f to run-tests.py.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Instead of hard-coding four different cases, use variables
(and printf) to reduce the duplication.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Instead of re-implementing a command-line parser, use the
argparse module.
The only real change (I hope) is that the test module must
now be given to the -f option without the .py suffix.
Also, --help now works, and if a test module/test name is
given that doesn't exist, the valid list is printed.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Instead of hardcoding logs/, allow putting LOGDIR into
the environment. This helps run tests in a VM where the
rootfs might be mounted read-only.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
test_ap_change_ssid verifies that the SET and RELOAD control interface
commands can be used to change the SSID of a hostapd-controlled WPA2-PSK
AP, i.e., for a case where the PSK needs to be derived again after the
SSID change.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The test_ap_hs20_username* test cases verify that a username/password
credential can be used for Hotspot 2.0 connection and that the network
type is reported correctly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
test_ap_hs20_ext_sim_roaming is otherwise identical with
test_ap_hs20_ext_sim, but the network is operated by a roaming partner.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that the network type (home/roaming/unknown) is available
and set properly in the test_ap_hs20_ext_sim test case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the scripts must be run from the source directory to
find the tests to run, they can use a relative path to the
wpaspy module instead of requiring it to be installed.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
"run-tests.py -S <db file> -L" can now be used to update a database
table with the current set of test cases and their descriptions.
Signed-hostap: Jouni Malinen <j@w1.fi>
cfg80211 may keep some state (e.g., regulatory domain), so make sure
this gets cleared between each full testing cycle.
Signed-hostap: Jouni Malinen <j@w1.fi>
test_p2p_go_invite_auth is similar to test_p2p_go_invite with the main
difference being in the peer device pre-authorizing the invitation
instead of processing invitation at upper layers after having received
it.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no point trying to go through a test case if the NOTE command
to write TEST-START entry does not succeed. This avoids some excessive
waits on buildbot trying to forcefully kill the programs on its timeout
if wpa_supplicant gets stuck waiting for something (like the current
issue with libnl events and commands having a chance of hitting a
blocking wait on netlink messages).
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds more coverage to testing by forcing the GO to be found with an
older entry in the BSS table and with that entry having a different
operating channel. Such a case has found issues with PD retries and
scanning if incorrect frequency and SSID is selected for the group.
Instead of relying on the old BSS entry with different operating channel
to happen based on a specific test case sequence, force this to happen
for this test case every time.
Signed-hostap: Jouni Malinen <j@w1.fi>
This verifies network selection using 3GPP Network Information and
connection using EAP-SIM with GSM authentication handled by an external
program.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is in preparation for supporting multiple domain values after which
setting the domain value does not replace the old value, but adds a new
one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a test run is terminated forcefully, hlr_auc_gw could have been left
running and/or some of the control interface files could still remain.
This could result in hlr_auc_gw not starting again for the next test
run.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Do not fail the EAP-SIM/AKA/AKA' test cases if hlr_auc_gw is not
available since hlr_auc_gw is not considered required part for the test
setup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some older systems used admin group, but adm group seems to be more
common nowadays, so detect this automatically rather than assume admin
group is used.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used by test cases that depend on some external component
that may not always be available to indicate clearly that a test case
was skipped rather than passed or failed.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no point trying to go through the tests if hostapd and
wpa_supplicant processes cannot be started properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
cfg80211/mac80211 seems to getting stuck with scans every now and then.
Check for this special state and delay return from reset() until the
driver has stopped the scan operation. This reduces likelihood of
failing multiple test cases in a row because of a single error.
Signed-hostap: Jouni Malinen <j@w1.fi>
test_p2p_go_invite verifies that GO can invite a peer in a case where
the operating channel and peer's listen channel are different.
Signed-hostap: Jouni Malinen <j@w1.fi>
run-all.sh and start.sh scripts can now take 'trace' command line
argument to request Linux tracing information from mac80211, cfg80211,
and wpa_supplicant to be recorded.
Signed-hostap: Jouni Malinen <j@w1.fi>
This avoids some issues with the global control interface socket
getting stuck with send buffer limit reached if test cases did not
use wait_global_event().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some test runs have resulted in wpa_supplicant being unresponsive or
very slow on the control interface. Check for that type of issues as
part of the reset sequence that is done between each test case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
test_persistent_group_invite_removed_client verifies that a client
that is removed from a group can rejoin based on new invitation.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use test_autogo to verify that P2P client is able to notice explicit
group session termination message from the GO. This would have caught
the regression in processing P2P deauthentication notifications.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is another one of the test cases that can time out frequently
under valgrind during WPS exchange. Increase the timeout to make
false error reports less likely to occur.
Signed-hostap: Jouni Malinen <j@w1.fi>
Number of crypto operations seem to take very long time in the valgrind
tests (about five seconds for public key generation for M1 and M2 on a
virtual server) and this is enough to push the test runs to hit the
timeout frequently even when there is no real error. Make this less
frequent by increasing WPS test case timeout from 15 to 30 seconds to
avoid issues based on the test scripts.
Signed-hostap: Jouni Malinen <j@w1.fi>
Number of crypto operations seem to take very long time in the valgrind
tests (about five seconds for passphrase to PSK mapping and for public
key generation for M1 and M2 on a virtual server) and this is enough to
push the test runs to hit the timeout frequently even when there is no
real error. Make this less frequent by increasing group formation
timeout from 15 to 20 seconds to avoid issues based on the test scripts
(15 + config time seconds timeout in the protocol may still kick in,
though).
Signed-hostap: Jouni Malinen <j@w1.fi>
Wait a bit longer for wpa_supplicant/hostapd to exit and clear control
interface files separately if either any of the cleanup steps fail to do
so.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of waiting for a fixed duration, poll hostapd/wpa_supplicant
through the control interface until they are ready to reply in order to
avoid starting test case execution too early. This is like commit
b76579e0c0 but for the concurrent P2P test
cases that were forgotten from that commit.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like mac80211 does not always manage to join the same IBSS and
this can result in test_ibss_rsn failures. Detect this case and try to
get the IBSSes to merge by running a scan prior to continuing with the
test case.
Signed-hostap: Jouni Malinen <j@w1.fi>
The handshake between STA2 and STA1 was not tracked previously. For
completeness, include that in the list of handshakes that are explicitly
waited for to complete prior to starting the connectivity tests. Since
all key setup should be done at this point, remove the extra wait before
the last connectivity test between STA1 and STA2.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like there may not be enough time to complete this test case in
15 seconds under valgrind on a virtual host every time, so increase the
timeout to 30 seconds to get more consistent test results.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of waiting for a fixed duration, poll hostapd/wpa_supplicant
through the control interface until they are ready to reply in order to
avoid starting test case execution too early.
Signed-hostap: Jouni Malinen <j@w1.fi>
Try to make sure new testing can be started by forcing
hostapd/wpa_supplicant to be killed with SIGKILL if needed. In addition,
wait a bit longer when killing the processes to avoid issues with the
next test run starting before the old one has been fully terminated.
Signed-hostap: Jouni Malinen <j@w1.fi>
The previous design of having to provide valgrind parameter to
stop-wifi.sh did not work since the new test setup may no match the
previous one. Instead of trying to figure out what needs to be stopped
based on previous run, stop all wpa_supplicant/hostapd processes running
under valgrind unconditionally to avoid cases where new set of processes
cannot be started due to existing processed.
Signed-hostap: Jouni Malinen <j@w1.fi>
test_ibss_rsn has been failing pretty frequently due to various issues
in getting all connections up. Try to address this initially by avoiding
concurrent operations and explicitly waiting for 4-way handshake
completion before testing data connection. Once this test case is
workign more robustly, a more difficult case with concurrent operations
can be added as a separate test case.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it easier to figure out what failed and allows builbot to
integrate multiple logs and state information about the test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like some virtual host setups are too slow to get
wpa_supplicant initialized under valgrind and this was triggering test
failures. Work around this by using even a longer wait before test case
execution.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like valgrind could not under buildbot with the default file
mode. Fix this by making wpa_supplicant and hostapd binaries readable
and executable by everyone.
Signed-hostap: Jouni Malinen <j@w1.fi>
./run-all.sh can now take an optional argument to select whether to run
all test cases as before (default), to run these under valgrind
("valgrind"), to run P2P test cases with concurrent station interface
("concurrent"), or the concurrent P2P test cases under valgrind
("concurrent-valgrind").
valgrind cases report errors if a test case fails or valgrind reports an
error.
Signed-hostap: Jouni Malinen <j@w1.fi>
print and logger.info() were directing output to different locations
(stdout and stderr, respectively) which resulted in buildbot showing
reordered entries. Use logger consistently to avoid that.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like the NOTE commands can time out in some cases. Avoid
stopping the test run in such a case to get more coverage if this is a
temporary issue.
Signed-hostap: Jouni Malinen <j@w1.fi>
The design for launching AP mode interfaces was changed, but
start-p2p-concurrent.sh was not updated with matching changes.
Signed-hostap: Jouni Malinen <j@w1.fi>
Make sure the connection between each STA and the AP is in working state
between each TDLS setup/teardown operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows more consistent interface to be used regardless of which
P2P driver design is used (especially for P2P management operations
over netdev vs. dedicated P2P_DEVICE).
Signed-hostap: Jouni Malinen <j@w1.fi>
The scan results from old test cases showing different SSID on the AP
can result in false failures, so avoid those by ignoring old scan
results from cfg80211.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Stopping the AP first was not ideal for the test cases since it could
result in wpa_supplicant trying to connect back and start a scan at the
end of a test case and cause problems for the following test case that
tried to scan in the beginning while the previously started scan was
still in progress.
Signed-hostap: Jouni Malinen <j@w1.fi>
Do not print the potentially long list of passed test cases. In case of
failure(s), make sure the failed test list is the last item in the
report.
Signed-hostap: Jouni Malinen <j@w1.fi>
The WPS tests are more prone to fail if scan results from the previous
test cases are allowed to remain in the wpa_supplicant BSS table during
the consecutive test since the test setup uses the same BSSID for the
test APs that change their configuration. Avoid these mostly bogus
issues by enforcing wpa_supplicant to drop and ignore old scan results
during the WPS test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
This removes the unnecessary separation of P2P (no hostapd) and AP
tests. The same scripts can be used to prepare for these tests and to
execute the tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
