Define MAC address fetching for OS X (by reusing the existing FreeBSD
implementation) to allow full compile testing of the WPS implementation
on a more BSD-like platform.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
struct ifreq does not include the ifr_netmask alternative on FreeBSD, so
replace that more specific name with ifr_addr that works with both Linux
and FreeBSD.
Fixes: 5b78c8f961 ("WPS UPnP: Do not allow event subscriptions with URLs to other networks")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
While it is appropriate to try to retransmit the event to another
callback URL on a failure to initiate the HTTP client connection, there
is no point in trying the exact same operation multiple times in a row.
Replve the event_retry() calls with event_addr_failure() for these cases
to avoid busy loops trying to repeat the same failing operation.
These potential busy loops would go through eloop callbacks, so the
process is not completely stuck on handling them, but unnecessary CPU
would be used to process the continues retries that will keep failing
for the same reason.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
More than about 700 character URL ended up overflowing the wpabuf used
for building the event notification and this resulted in the wpabuf
buffer overflow checks terminating the hostapd process. Fix this by
allocating the buffer to be large enough to contain the full URL path.
However, since that around 700 character limit has been the practical
limit for more than ten years, start explicitly enforcing that as the
limit or the callback URLs since any longer ones had not worked before
and there is no need to enable them now either.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The UPnP Device Architecture 2.0 specification errata ("UDA errata
16-04-2020.docx") addresses a problem with notifications being allowed
to go out to other domains by disallowing such cases. Do such filtering
for the notification callback URLs to avoid undesired connections to
external networks based on subscriptions that any device in the local
network could request when WPS support for external registrars is
enabled (the upnp_iface parameter in hostapd configuration).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use value 2 to point to RFC 5480 which describes the explicit
indicatiotion of the public key being in compressed form.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is in preparation of implementation changes to check SAE-PK
password length more accurately based on the Sec value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new sae_commit_status and sae_pk_omit configuration parameters and
an extra key at the end of sae_password pk argument can be used to
override SAE-PK behavior for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is mainly for testing purposes to allow more convenient checking of
station behavior when a transition mode is disabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wpa_supplicant disables PMKSA caching with FT-EAP by default due to
known interoperability issues with APs. This is allowed only if the
network profile is explicitly enabling caching with
ft_eap_pmksa_caching=1. However, the PMKID for such PMKSA cache entries
was still being configured to the driver and it was possible for the
driver to build an RSNE with the PMKID for SME-in-driver cases. This
could result in hitting the interop issue with some APs.
Fix this by skipping PMKID configuration to the driver fot FT-EAP AKM if
ft_eap_pmksa_caching=1 is not used in the network profile so that the
driver and wpa_supplicant behavior are in sync for this.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define QCA vendor attribute in SET(GET)_WIFI_CONFIGURATION to
dynamically configure capabilities for dynamic bandwidth adjustment.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Define QCA vendor attribute in SET(GET)_WIFI_CONFIGURATION to
dynamically configure capabilities for channel width.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Add support for missing driver AKM capability flags from the list of
RSN_AUTH_KEY_MGMT_* flags and make these available through the
'GET_CAPABILITY key_mgmt' control interface command.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new QCA vendor attributes to configure RSNXE Used (FTE), ignore CSA,
and OCI frequency override with QCA vendor command
QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION for STA testbed role.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This maintains knowledge of whether H2E or PK was used as part of the
SAE authentication beyond the removal of temporary state needed during
that authentication. This makes it easier to use information about which
kind of SAE authentication was used at higher layer functionality.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
There is no need to update the WPS IE in Beacon frames when a
subscription is removed if that subscription is not for an actual
selected registrar. For example, this gets rids of unnecessary driver
operations when a subscription request gets rejected when parsing the
callback URLs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
While this is not explicitly defined as the limit, lambda=8 (i.e., 9
characters with the added hyphen) is needed with Sec=5 to reach the
minimum required resistance to preimage attacks, so use this as an
implicit definition of the password length constraint.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Lambda >= 12 is needed with Sec = 2, so drop the shorter password
lengths in the sae_pk and module_wpa_supplicant test cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
While the current implementation forces these groups to be same, that is
not strictly speaking necessary and the correct group to use here is
K_AP, not the SAE authentication group.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds AP side functionality for SAE-PK. The new sae_password
configuration parameters can now be used to enable SAE-PK mode whenever
SAE is enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds core SAE functionality for a new mode of using SAE with a
specially constructed password that contains a fingerprint for an AP
public key and that public key being used to validate an additional
signature in SAE confirm from the AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Convert the previously used text log entries to use the more formal
OCV-FAILURE prefix and always send these as control interface events to
allow upper layers to get information about unexpected operating channel
mismatches.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add hostapd configuration parameters oci_freq_override_* to allow the
OCI channel information to be overridden for various frames for testing
purposes. This can be set in the configuration and also updated during
the runtime of a BSS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
OSEN STAs are not authenticated, so do not send the actual BIGTK for
them so that they cannot generate forged protected Beacon frames. This
means that OSEN STAs cannot enable beacon protection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not include the actual GTK/IGTK value in FT protocol cases in OSEN or
with DGAF disabled (Hotspot 2.0). This was already the case for the
EAPOL-Key cases of providing GTK/IGTK, but the FT protocol case was
missed. OSEN cannot really use FT, so that part is not impacted, but it
would be possible to enable FT in a Hotspot 2.0 network that has DGAF
disabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not include the actual GTK/IGTK value in WNM Sleep Mode Response
frame if WNM Sleep Mode is used in OSEN or in a network where use of GTK
is disabled. This was already the case for the EAPOL-Key cases of
providing GTK/IGTK, but the WNM Sleep Mode exit case was missed.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When a single hostapd process manages both the OWE and open BSS for
transition mode, owe_transition_ifname can be used to clone the
transition mode information (i.e., BSSID/SSID) automatically. When both
BSSs use ACS, the completion of ACS on the 1st BSS sets state to
HAPD_IFACE_ENABLED and the OWE transition mode information is updated
for all the other BSSs. However, the 2nd BSS is still in the ACS phase
and the beacon update messes up the state for AP startup and prevents
proper ACS competion.
If 2nd BSS is not yet enabled (e.g., in ACS), skip beacon update and
defer OWE transition information cloning until the BSS is enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an attribute QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED
to get the response for the queried data.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that all associated STAs that claim support for OCV initiate an
SA Query after CSA. If no SA Query is seen within 15 seconds,
deauthenticate the STA.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the OCV-FAILURE control interface event to notify upper layers of
OCV validation issues in FT and FILS (Re)Association Request frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the OCV-FAILURE control interface event to notify upper layers of
OCV validation issues in EAPOL-Key msg 2/4 and group 2/2.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new OCV-FAILURE control interface event to notify upper layers of
OCV validation issues. This commit adds this for SA Query processing in
AP mode.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make reporting of OCV validation failure reasons more flexible by
removing the fixed prefix from ocv_verify_tx_params() output in
ocv_errorstr so that the caller can use whatever prefix or encapsulation
that is most appropriate for each case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
To support the STA testbed role, the STA has to use specified channel
information in OCI element sent to the AP in EAPOL-Key msg 2/4, SA Query
Request, and SA Query Response frames. Add override parameters to use
the specified channel while populating OCI element in all these frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It was possible for the RSN state machine to maintain old PMKSA cache
selection (sm->cur_pmksa) when roaming to another BSS based on
driver-based roaming indication. This could result in mismatching state
and unexpected behavior, e.g., with not generating a Suite B PMKSA cache
entry.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define QCA vendor attributes for SET(GET)_WIFI_CONFIGURATION to
dynamically configure capabilities for TX A-MSDU and RX A-MSDU.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Add a QCA vendor subcommand QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC
to add and delete TSPEC in STA mode.
The attributes defined in enum qca_wlan_vendor_attr_config_tspec
are used to encapsulate required information.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Add new QCA vendor attributes to configure misbehavior for PMF
protection for Management frames and to inject Disassociation frames.
These attributes are used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an attribute that can be used with
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION vendor command to
configure different PHY modes to the driver/firmware.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wpa_supplicant registered to process the Radio Measurement Request
frames unconditionally. This would prevent other location based
applications from handling these frames. Enable such a use case by
allowing wpa_supplicant to be configured not to register to process
these frames. This can now be done by adding "no_rrm=1" to the
driver_param configuration parameter.
In addition, wpa_driver_nl80211_init() does not have the provision to
take driver_params. Hence, resubscribe again with cfg80211 when this
driver parameter "no_rrm=1" is set after the initial setup steps.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process HE 6 GHz band capabilities in (Re)Association Request frames and
pass the information to the driver.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Construct HE 6 GHz Band Capabilities element (IEEE 802.11ax/D6.0,
9.4.2.261) from HT and VHT capabilities and add it to Beacon, Probe
Response, and (Re)Association Response frames when operating on the 6
GHz band.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
The VHT Operation Information subfield is conditonally present, so do
not hardcoded it in struct ieee80211_he_operation. These members of the
struct are not currently used, so these can be removed without impact to
functionality.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Defines IEEE P802.11ax/D6.0, 9.4.2.261 HE 6 GHz Band Capabilities
element and 6 GHz Operation Information field of HE Operation element
(IEEE P802.11ax/D6.0, Figure 9-787k).
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Use a shared wpa_alg_bip() function for this and fix the case in
nl_add_key() to cover all BIP algorithms. That fix does not change any
behavior since the function is not currently used with any BIP
algorithm, but it is better to avoid surprises should it ever be needed
with IGTK.
Signed-off-by: Jouni Malinen <j@w1.fi>
IGTK is the key that is used a BIP cipher. WPA_ALG_IGTK was the
historical name used for this enum value when only the AES-128-CMAC
based BIP algorithm was supported. Rename this to match the style used
with the other BIP options.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation used mp_rand_prime() to generate a random
value in range 0..m. That is insanely slow way of generating a random
value since mp_rand_prime() is for generating a random _prime_ which is
not what is needed here. Replace that implementation with generationg of
a random value in the requested range without doing any kind of prime
number checks or loops to reject values that are not primes.
This speeds up SAE and EAP-pwd routines by couple of orders of
magnitude..
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit dd74ddd0df ("nl80211: Handle AKM suite selectors for AP
configuration") added warning log message "nl80211: Not enough room for
all AKM suites (num_suites=X > NL80211_MAX_NR_AKM_SUITES)" which in some
cases fills logs every 3 seconds, so fix this by increasing the log
message level to debug.
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Ref: https://patchwork.ozlabs.org/project/openwrt/patch/20200504130757.12736-1-ynezz@true.cz/#2429246
Fixes: dd74ddd0df ("nl80211: Handle AKM suite selectors for AP configuration")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
It is possible for drivers to report received Management frames while AP
is going through initial setup (e.g., during ACS or DFS CAC). hostapd
and the driver is not yet ready for actually sending out responses to
such frames at this point and as such, it is better to explicitly ignore
such received frames rather than try to process them and have the
response (e.g., a Probe Response frame) getting dropped by the driver as
an invalid or getting out with some incorrect information.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows nl80211-based drivers to get the frame out. The old earlier
location resulted in the driver operation getting rejected before the
kernel was not ready to transmit the frame in the BSS context of the AP
interface that has not yet been started.
While getting this broadcast Deauthentication frame transmitted at the
BSS start is not critical, it is one more chance of getting any
previously associated station notified of their previous association not
being valid anymore had they missed previous notifications in cases
where the AP is stopped and restarted.
Signed-off-by: Jouni Malinen <j@w1.fi>
cfg80211 takes care of key removal when link/association is lost, so
there is no need to explicitly clear old keys when starting AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
Linux bridging code does not allow a station mode WLAN interface in a
bridge and this prevents the AP mode scan workaround from working if the
AP interface is in a bridge and scanning can be only done by moving to
STA mode. Extend this workaround to remove the interface from the bridge
temporarily for the duration of the scan, i.e., for the same duration as
the interface needs to be moved into the station.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new hostapd control interface command "DPP_CHIRP own=<BI ID>
iter=<count>" to request chirping, i.e., sending of Presence
Announcement frames, to be started. This follows the model of similar
wpa_supplicant functionality from commit 562f77144c ("DPP2: Chirping
in wpa_supplicant Enrollee"). The hostapd case requires the AP to be
started without beaconing, i.e., with start_disabled=1 in hostapd
configuration, to allow iteration of channels needed for chirping.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Clean struct hapd_interfaces pointers and interface count during
deinitialization at the end of theh ostapd process termination so that a
call to hostapd_for_each_interface() after this does not end up
dereferencing freed memory. Such cases do not exist before this commit,
but can be added after this, e.g., for DPP needs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When hostapd is started without beaconing (start_disabled=1), Public
Action frame transmission command through nl80211 needs to allow
offchannel operations regardless of the operating channel configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This file needs the EVP_PKEY_get0_EC_KEY() compatibility wrapper just
like other DPP source code files using this function.
Fixes: 21c612017b ("DPP: Move configurator backup into a separate source code file")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The driver can advertise supported AKMs per wiphy and/or per interface.
Populate per interface supported AKMs based on the driver advertisement
in the following order of preference:
1. AKM suites advertised by NL80211_ATTR_IFTYPE_AKM_SUITES
2. AKM suites advertised by NL80211_ATTR_AKM_SUITES
If neither of these is available:
3. AKMs support is assumed as per legacy behavior.
In addition, extend other driver interface wrappers to set the
per-interface values based on the global capability indication.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Since this functionality was not used for anything in practice, it is
easier to simply remove this functionality completely to avoid potential
conflicts in using the kernel tree upstream commit ab4dfa20534e
("cfg80211: Allow drivers to advertise supported AKM suites").
This is practically reverting the commit 8ec7c99ee4 ("nl80211: Fetch
supported AKM list from the driver").
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
This allows DPP_AUTH_INIT to be used with tcp_addr=<dst> argument and
Configurator parameters to perform Configurator initiated DPP
provisioning over TCP. Similarly, DPP_CONTROLLER_START can now be used
to specify Configurator/Enrollee roles and extend Controller to work in
Enrollee role.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Recognize the Reconfig Announcement message type and handle it similarly
to the Presence Announcement in the Relay, i.e., send it to the first
Controller if the local Configurator does not have matching C-sign-key.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use the new struct dpp_authentication instance when setting Configurator
parameters for authentication exchange triggered by Presence
Announcement. conn->auth is NULL here and would cause dereferencing of a
NULL pointer if dpp_configurator_params is set.
Fixes: fa5143feb3 ("DPP2: Presence Announcement processing in Controller")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend Enrollee functionality to process Reconfig Authentication
Confirm message and start GAS client.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend Configurator functionality to sign a special Connector for
reconfiguration and reply with Reconfig Authentication Request frame
when Reconfig Announcement frame is received with a matching C-sign key
hash value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check if there is a matching Configurator and be ready to initiate
Reconfig Authentication (which itself is not included in this commit).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend DPP chirping mechanism to allow Reconfig Announcement frames to
be transmitted instead of the Presence Announcement frames. Add a new
wpa_supplicant control interface command "DPP_RECONFIG <network id>" to
initiate reconfiguration for a specific network profile.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Split ke derivation into two parts so that the previously used
internal-only PRK gets stored as the bk in the authentication state.
This new key will be needed for deriving additional keys with DPP R2.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This removes unnecessary allocations and simplifies the implementation
by not having to remember to free the cloned reference.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Fix a copy-paste error in parsing the version info.
Fixes: 7dd768c3ca ("DPP2: Version information in bootstrapping info URI")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the local supported version information into the bootstrapping
information (V=2 in the URI) and parse this from received URI.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Report MUD URL and bandSupport from config request if those optional
nodes are included. For now, these are mainly for testing purposes since
there is no mechanism to delay sending of config response.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When DPP v2 implementation is hardcoded to behave as v1 for testing
purposes, leave out the Protocol Version attribute form Authentication
Request instead of including it there with indication for v1.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This simplifies dpp_build_conf_obj_dpp() and makes it easier to share
the signing functionality for other purposes like reconfiguration where
the Configurator needs to sign a dppCon object for itself without
generating the encapsulating config object.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"SET dpp_version_override <ver>" can now be used to request
wpa_supplicant and hostapd to support a subset of DPP versions. In
practice, the only valid case for now is to fall back from DPP version 2
support to version 1 in builds that include CONFIG_DPP2=y.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not allow association to continue if the local configuration enables
PFS and the station indicates it supports PFS, but PFS was not
negotiated for the association.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not allow association to continue if the local configuration enables
PFS and the station indicates it supports PFS, but PFS was not
negotiated for the association.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new "dpp_pfs=1" entry can be used to determine whether PFS was used
during derivation of PTK when DPP AKM is negotiated for an association.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check AP's DPP Protocol Version during network introduction and mark the
PMKSA cache as suitable for PFS use with version 2 or newer. This avoids
unnecessary attempt of negotiating PFS with version 1 APs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This can be used to determine whether to try to negotiate PFS (only
available with version 2 or higher).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE 802.11 defines reason codes for indicating 4-way handshake and
group key handshake timeouts. Use those reason codes instead of the more
generic one for these particular cases in the Authenticator state
machine.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Convert driver indications to internal events to allow invalid Beacon
frames to be reported to the AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update frame processing registration for DPP Public Action frames to
include multicast reception when in DPP listen mode and the driver
indicates support for this type of explicit request.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Documentation of the return values for wpa_parse_vendor_specific() and
wpa_parse_generic() were not accurate and the parsing results from these
were not really handled appropriately. There is no point in calling
wpa_parse_vendor_specific() if wpa_parse_generic() recognizes a KDE. Not
that this would break anything in practice, but still, it looks
confusing.
The part about handling wpa_parse_vendor_specific() return value can, at
least in theory, break some cases where an unexpectedly short KDE/vendor
specific element were present and something would need to be recognized
after it. That does not really happen with any standard compliant
implementation and this is unlikely to cause any real harm, but it is
clearer to handle this more appropriately even for any theoretical case,
including misbehavior of a peer device.
Instead of stopping parsing on too short vendor specific element,
continue parsing the following KDEs/IEs. Skip the
wpa_parse_vendor_specific() call when a KDE has been recognized. Also
fix the return value documentation for wpa_parse_generic() and remove
the useless return value from wpa_parse_vendor_specific().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
We have practically started requiring some C99 features, so might as
well finally go ahead and bring in the C99 bool as well.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
EVP_PKEY_get0_EC_KEY() compatibility wrapper is used only within
CONFIG_DPP2 blocks, so define it with matching condition.
Signed-off-by: Jouni Malinen <j@w1.fi>
This has no changes to the function itself, i.e., it is just moved to a
location that is above the first caller.
Signed-off-by: Jouni Malinen <j@w1.fi>
drv->eapol_sock is used only for receiving EAPOL frames in AP mode, so
it is not needed when using control port for EAPOL frame RX.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since this nl80211 mechanism for sending EAPOL frames does not currently
support TX status notification, disable it by default of AP mode where
the Authenticator state machine uses those notifications to optimize
retransmission. The control port TX can be enabled for AP mode with
driver param control_port_ap=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use and/or set socker owner where necessary to allow EAPOL frames to be
received using the nl80211 control port. This is done when the driver
indicates support for the control port without previous hardcoded
reception of RSN preauth frames.
Use methods which set or use the connection owner nl_sock * where
necessary. Initial operations need to register with the SOCKET_OWNER
attribute set (e.g., connect for STA mode). Final operations need to use
the socket which holds the owner attribute (e.g., disconnect for STA
mode).
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
This commit creates a connect nl_sock * for every bss unconditionally.
It is used in the next commit for nl80211 control port RX.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
nl80211 control port event handling previously did not differentiate
between EAPOL and RSN preauth ethertypes. Add checking of the ethertype
and report unexpected frames (only EAPOL frames are supposed to be
delivered through this path).
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
This is needed since the initial implementation of the control port
mechanism in the kernel mixed in RSN pre-authentication ethertype
unconditionally (and IMHO, incorrectly) into the control port.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a build flag CONFIG_NO_TKIP=y to remove all TKIP functionality from
hostapd and wpa_supplicant builds. This disables use of TKIP as both the
pairwise and group cipher. The end result does not interoperate with a
WPA(v1)-only device or WPA+WPA2 mixed modes.
Signed-off-by: Disha Das <dishad@codeaurora.org>
Allow hostapd to be requested to override the RSNXE Used subfield in FT
reassociation case for testing purposes with "ft_rsnxe_used=<0/1/2>"
where 0 = no override, 1 = override to 1, and 2 = override to 0.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The only l2_packet use within this file was removed by commit
d12dab4c6f ("nl80211: Use non-receiving socket for EAPOL TX").
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow wpa_supplicant to be requested to override the RSNXE Used subfield
in FT reassociation case for testing purposes with "SET ft_rsnxe_used
<0/1/2>" where 0 = no override, 1 = override to 1, and 2 = override to
0.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Discard the FT Reassociation Request frame instead of rejecting it
(i.e., do not send Reassociation Response frame) if RSNXE Used is
indicated in FTE, but no RSNXE is included even though the AP is
advertising RSNXE.
While there is not really much of a difference between discarding and
rejecting the frame, this discarding behavior is what the standard says
for this type of an error case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an attribute QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FREQUENCY_2
for describing the secondary 80 MHz span of agile spectral scan.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The "FT: Ignore extra data in end" hexdump is quite confusing since it
shows all the IEs that were actually either processed or forwarded.
There is no code path that could reach this debug print with actual real
extra data. Remove it and the dead increment of pos to avoid warnings
from static analyzers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow STA entry to be removed and re-added to the driver with PMF is
used with FT. Previously, this case resulted in cfg80211 rejecting STA
entry update after successful FT protocol use if the association had not
been dropped and it could not be dropped for the PMF case in
handle_auth().
Signed-off-by: Jouni Malinen <j@w1.fi>
Mark own bootstrap information as having been used in NFC negotiated
connection handover and do not accept non-mutual authentication when
processing Authentication Response from the peer when such bootstrapping
information is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Connector alone is not sufficient for authentication during
reconfiguration, so store the netAccessKey as well.
Fixes: e4eb009d98 ("DPP2: Add Connector and C-sign-key in psk/sae credentials for reconfig")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
While the Diffie-Hellman Parameter element is defined in RFC 8110
explicitly for use witht he OWE AKM, it has now been proposed to be used
with another AKM (DPP). Should any other AKM be extended in similar
manner in the future, the check against unexpected use could result in
additional interoperability issues. Remove that and instead, ignore the
unexpected Diffie-Hellman Parameter element if it is included in
(Re)Association Request frame when any other AKM is negotiated.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the Enrollee indicates support for DPP R2 or newer, add Connector and
C-sign-key in psk/sae credentials (i.e., cases where DPP AKM is not
enabled) for reconfiguration. Extend processing of such credentials in
wpa_supplicant network profile addition to handle this new case
correctly by not setting key_mgmt=DPP based on Connector being present,
but by looking at the actual akm value in the config object.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a driver interface event for Beacon frame protection failures.
Report such events over the control interface and send a
WNM-Notification Request frame to the AP as well.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add HE override support under the build parameter CONFIG_HE_OVERRIDES=y.
The disable_he=1 network profile parameter can be used to disable HE.
This requires a fallback to VHT on the 5 GHz band and to HT on the 2.4
GHz band.
There is no nl80211 support for configuring the driver to disable HE, so
for now, this applies only to IBSS and mesh cases.
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
In repeater mode remote AP may request channel switch to a new channel.
Check if DFS is required for the new channel before proceeding with
normal AP operations. Start CAC procedure if radar detection is required
and channel is not yet marked as available.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Add a new hostapd_is_dfs_overlap() helper function to DFS module. This
function tells whether the selected frequency range overlaps with DFS
channels in the current hostapd configuration. Selected frequency reange
is specified by its center frequency and bandwidth.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Rename DFS helper hostapd_config_dfs_chan_available() to
hostapd_is_dfs_chan_available(). Enable access to this helper function
from other hostapd components.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
EVP_PKEY_get0_EC_KEY() was added in OpenSSL 1.1.0, so add a
compatibility wrapper for it when building with OpenSSL 1.0.2.
Fixes: c025c2eb59 ("DPP: DPPEnvelopedData generation for Configurator backup")
Fixes: 7d9e320054 ("DPP: Received Configurator backup processing")
Signed-off-by: Jouni Malinen <j@w1.fi>
The new skip_prune_assoc=1 parameter can be used to configure hostapd
not to prune associations from other BSSs operated by the same process
when a station associates with another BSS. This can be helpful in
testing roaming cases where association and authorization state is
maintained in an AP when the stations returns.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new driver param full_ap_client_state=0 can be used to test
functionality with the driver capability for full AP client state being
forced to be disabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use local variables to avoid sm->wpa_auth->conf type of dereferences
where multiple instances within a function can be cleaned up.
Signed-off-by: Jouni Malinen <j@w1.fi>
Drivers that trigger roaming need to know the lifetime and reauth
threshold time of configured PMKSA so that they can trigger full
authentication to avoid unnecessary disconnection. To support this, send
dot11RSNAConfigPMKLifetime and dot11RSNAConfigPMKReauthThreshold values
configured in wpa_supplicant to the driver while configuring a PMKSA.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
The new hostapd configuration parameter dpp_pfs can be used to specify
how PFS is applied to associations. The default behavior (dpp_pfs=0)
remains same as it was previously, i.e., allow the station to decide
whether to use PFS. PFS use can now be required (dpp_pfs=1) or rejected
(dpp_pfs=2).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add definition for HE bit in neighbor report BSSID Information field
from IEEE P802.11ax/D6.0, 9.4.2.36 Neighbor Report element.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
This functionality was repeated for multiple different frames. Use a
shared helper function to avoid such duplication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process the received Presence Announcement frames in Controller. If a
matching bootstrapping entry for the peer is found, initiate DPP
authentication to complete provisioning of the Enrollee.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process the received Presence Announcement frames in AP/Relay. If a
matching bootstrapping entry for the peer is found in a local
Configurator, that Configurator is used. Otherwise, the frame is relayed
to the first configured Controller (if available).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process received Presence Announcement frames and initiate
Authentication exchange if matching information is available on the
Configurator.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new hostapd configuration parameter
dpp_configurator_connectivity=1 to request Configurator connectivity to
be advertised for chirping Enrollees.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wpa_supplicant control interface command "DPP_CHIRP own=<BI
ID> iter=<count>" to request chirping, i.e., sending of Presence
Announcement frames, to be started.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new identifier definitions for presence announcement,
reconfiguration, and certificate enrollment.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"DPP_BOOTSTRAP_SET <ID> <configurator parameters..>" can now be used to
set peer specific configurator parameters which will override any global
parameters from dpp_configurator_params.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a more convenient way of addressing cases where a
Configurator/Controller may store a large number of peer bootstrapping
information instances and may need to manage different configuration
parameters for each peer while operating as the Responder.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Set the global pointer and msg_ctx when allocating struct
dpp_authentication instead of needing to pass these to
dpp_set_configurator().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd (and wpa_supplicant in AP mode) was internally updating the STA
flags on disconnection cases to remove authorization and association.
However, some cases did not result in immediate update of the driver STA
entry. Update all such cases to send out the update to the driver as
well to reduce risk of race conditions where new frames might be
accepted for TX or RX after the port authorization or association has
been lost and configured keys are removed.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check whether the Transition Disable KDE is received from an
authenticated AP and if so, whether it contains valid indication for
disabling a transition mode. If that is the case, update the local
network profile by removing the less secure options.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new hostapd configuration parameter transition_disable can now be
used to configure the AP to advertise that use of a transition mode is
disabled. This allows stations to automatically disable transition mode
by disabling less secure network profile parameters.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the OUI Type and bitmap values for Transition Disable KDE. These
will be shared by both the AP and STA implementations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA_WLAN_VENDOR_CFR_NDPA_NDP_ALL in enum
qca_wlan_vendor_cfr_capture_type. This capture type requests all NDPA
NDP frames to be filtered.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd will trigger EDMG auto channel selection by setting
QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED. The 60 GHz driver will be
called to start an auto channel selection and will return the
primary channel and the EDMG channel.
Signed-off-by: Noam Shaked <nshaked@codeaurora.org>
Addition of chan_2ghz_or_5ghz_to_freq() broke 60 GHz ACS, because it
assumes reported ACS channel is on either 2.4 or 5 GHz band. Fix this
by converting chan_2ghz_or_5ghz_to_freq() to a more generic
chan_to_freq(). The new function uses hw_mode to support 60 GHz.
Fixes: 41cac481a8 ("ACS: Use frequency params in ACS (offload) completed event interface")
Signed-off-by: Noam Shaked <nshaked@codeaurora.org>
The parameters that need to be applied are symmetric to those of VHT,
however the validation code needs to be tweaked to check the HE
capabilities.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Enhanced channel frequency response supports capturing of channel status
information based on RX. Define previous CFR as version 1 and enhanced
CFR as version 2. If target supports both versions, two versions can't
be enabled at same time. Extend attributes for enhanced CFR capture in
enum qca_wlan_vendor_peer_cfr_capture_attr.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Support Extended Key ID in wpa_supplicant according to
IEEE Std 802.11-2016 for infrastructure (AP) associations.
Extended Key ID allows to rekey pairwise keys without the otherwise
unavoidable MPDU losses on a busy link. The standard is fully backward
compatible, allowing STAs to also connect to APs not supporting it.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Support Extended Key ID in hostapd according to IEEE Std 802.11-2016.
Extended Key ID allows to rekey pairwise keys without the otherwise
unavoidable MPDU losses on a busy link. The standard is fully backward
compatible, allowing an AP to serve STAs with and without Extended Key
ID support in the same BSS.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
This is more consistent with the other eloop registrations and avoids a
theoretical integer overflow with 16-bit int should more than 32767
sockets/signals/events be registered.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is more consistent with the other eloop registrations and avoids a
theoretical integer overflow with 16-bit int should more than 32767
sockets be registered (which is not really going to happen in practice).
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids a theoretical integer overflow with 16-bit unsigned int
should a certificate be encoded with more that 65535 friendly names or
icons.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is more consistent with the other eloop registrations and avoids a
theoretical integer overflow with 16-bit int (not that there would ever
be more that 32767 signal handlers getting registered).
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no point in starting a huge number of pending SA Queries, so
limit the number of pending queries to 1000 to have an explicit limit
for how large sa_query_count can grow.
Signed-off-by: Jouni Malinen <j@w1.fi>
While RADIUS messages are limited to 4 kB, use size_t to avoid even a
theoretical overflow issue with 16-bit int.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the kernel rtm_newlink or rtm_dellink send the maximum length of
ifname (IFNAMSIZ), the event handlers in
wpa_driver_nl80211_event_rtm_addlink() and
wpa_driver_nl80211_event_rtm_dellink() did not copy the IFLA_IFNAME
value. Because the RTA_PAYLOAD (IFLA_IFNAME) length already includes the
NULL termination, that equals the IFNAMSIZ.
Fix the condition when IFNAME reach maximum size.
Signed-off-by: Ouden <Ouden.Biz@gmail.com>
Add more hang reason codes for the hang reason in the
QCA_NL80211_VENDOR_SUBCMD_HANG events. This also introduces the
attribute QCA_WLAN_VENDOR_ATTR_HANG_REASON_DATA to carry the required
data for the respective hang reason. This data is expected to contain
the required dump to analyze the reason for the hang.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Some APs have managed to add two SSID elements into Beacon frames and
that used to result in picking the last one which had incorrect data in
the known examples of this misbehavior. Pick the first one to get the
correct SSID.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was not supposed to be conditional on CONFIG_FILS.
Fixes: ecbf59e693 ("wpa_supplicant configuration for Beacon protection")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
int_array_concat() and int_array_add_unique() could potentially end up
overflowing the int type variable used to calculate their length. While
this is mostly theoretical for platforms that use 32-bit int, there
might be cases where a 16-bit int overflow could be hit. This could
result in accessing memory outside buffer bounds and potentially a
double free when realloc() ends up freeing the buffer.
All current uses of int_array_add_unique() and most uses of
int_array_concat() are currently limited by the buffer limits for the
local configuration parameter or frame length and as such, cannot hit
this overflow cases. The only case where a long enough int_array could
be generated is the combination of scan_freq values for a scan. The
memory and CPU resource needs for generating an int_array with 2^31
entries would not be realistic to hit in practice, but a device using
LP32 data model with 16-bit int could hit this case.
It is better to have more robust checks even if this could not be
reached in practice, so handle cases where more than INT_MAX entries
would be added to an int_array as memory allocation failures instead of
allowing the overflow case to proceed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter no_beacon_rsnxe=1 can be used to
remove RSNXE from Beacon frames. This can be used to test protection
mechanisms for downgrade attacks.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous design for adding RSNXE into FT was not backwards
compatible. Move to a new design based on 20/332r3 to avoid that issue
by not include RSNXE in the FT protocol Reassociation Response frame so
that a STA not supporting RSNXE can still validate the FTE MIC
correctly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous design for adding RSNXE into FT was not backwards
compatible. Move to a new design based on 20/332r3 to avoid that issue
by not include RSNXE in the FT protocol Reassociation Request frame so
that an AP not supporting RSNXE can still validate the FTE MIC
correctly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that the AP included RSNXE in Beacon/Probe Response frames if it
indicated in FTE that RSNXE is used. This is needed to protect against
downgrade attacks based on the design proposed in 20/332r3.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that the STA includes RSNXE if it indicated in FTE that RSNXE is
used and the AP is also using RSNXE. This is needed to protect against
downgrade attacks based on the design proposed in 20/332r3.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a workaround needed to keep FT protocol backwards compatible for
the cases where either the AP or the STA uses RSNXE, but the other one
does not. This commit adds setting of the new field to 1 in
Reassociation Request/Response frame during FT protocol when the STA/AP
uses RSNXE in other frames. This mechanism is described in 20/332r3.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add key configuration parameters needed to support Extended Key ID with
pairwise keys. Add a driver capability flag to indicate support forusing
this.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
wpa_parse_kde_ies(), i.e., the only caller to wpa_parse_generic(),
verifies that there is room for KDE Length field and pos[1] (that
length) octets of payload in the Key Data buffer. The PMKID KDE case
within wpa_parse_generic() was doing an unnecessary separate check for
there being room for the Length, OUI, and Data Type fields. This is
covered by the check in the calling function with the combination of
verifying that pos[1] is large enough to contain RSN_SELECTOR_LEN +
PMKID_LEN octets of payload.
This is confusing since no other KDE case was checking remaining full
buffer room within wpa_parse_generic(). Clean this up by removing the
unnecessary check from the PMKID KDE case so that all KDEs are handled
consistently.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_parse_generic() can now recognize the Key ID KDE that will be needed
to deliver the Key ID of the pairwise key when Extended Key ID is used.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
KEY_FLAG_MODIFY was initial added for the planned Extended Key ID
support with commit a919a26035 ("Introduce and add key_flag") and then
removed with commit 82eaa3e688 ("Remove the not yet needed
KEY_FLAG_MODIFY") to simplify commit e9e69221c1 ("Validity checking
function for key_flag API").
Add it again and update check_key_flag() accordingly.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The actual TX status (whether ACK frame was received) was not included
in the debug log in AP mode. Add that for all cases. In addition, add
some more details in the debug log to make the log more helpful in
debugging issues related to frame delivery.
Signed-off-by: Jouni Malinen <j@w1.fi>
While 13.7.1 (FT reassociation in an RSN) in P802.11-REVmd/D3.0 did not
explicitly require this to be done, this is implied when describing the
contents of the fourth message in the FT authentication sequence (see
13.8.5). Furthermore, 20/332r2 is proposing an explicit validation step
to be added into 13.7.1.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 5f9b4afd ("Use frequency in HT/VHT validation steps done before
starting AP") modified hostapd_is_usable_edmg() to use freq instead of
channel numbers. Unfortunately, it did not convert the frequency
calculation correctly and this broke EDMG functionality.
Fix the frequency calculation so that EDMG channel 9 works again.
Fixes: 5f9b4afdfa ("Use frequency in HT/VHT validation steps done before starting AP")
Signed-off-by: Hrishikesh Vidwans <hvidwans@codeaurora.org>
Check whether an error is reported from any of the functions that could
in theory fail and if so, do not proceed with the partially filled SAE
commit buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
In theory, hmac_sha256() might fail, so check for that possibility
instead of continuing with undetermined index value that could point to
an arbitrary token entry.
Signed-off-by: Jouni Malinen <j@w1.fi>
The return value from nl80211_send_monitor() is not suitable for use
with strerror(). Furthermore, nl80211_send_monitor() itself is printing
out a more detailed error reason.
Signed-off-by: Jouni Malinen <j@w1.fi>
send_and_recv_msgs() returns a negative number as the error code and
that needs to be negated for strerror().
Fixes: 8759e9116a ("nl80211: Control port over nl80211 helpers")
Signed-off-by: Jouni Malinen <j@w1.fi>
send_auth_reply() could be called with sta == NULL in certain error
conditions. While that is not applicable for this special test
functionality for SAE, the inconsistent checks for the sta pointer could
result in warnings from static analyzers. Address this by explicitly
checking the sta pointer here.
Signed-off-by: Jouni Malinen <j@w1.fi>
mode->he_capab is an array and as such, there is no point in checking
whether it is NULL since that cannot be the case. Check for the
he_supported flag instead. In addition, convert the TWT responder
capability bit into a fixed value 1 to avoid any surprising to the
callers. In practice, neither of these changes results in different
behavior in the current implementation, but this is more robust.
Signed-off-by: Jouni Malinen <j@w1.fi>
There was a copy-paste error in this code that would be adding the
connectorTemplate once that becomes available. In practice, this was not
reachable code, but anyway, this should be ready for potential addition
of connectorTemplate in the future.
Signed-off-by: Jouni Malinen <j@w1.fi>
While there may have initially been cases where the RSNE from
Beacon/Probe Response frames was not available from some drivers, it is
now more valuable to notice if such a case were to be hit with drivers
that are always expected to have such information available. As such,
make it a fatal error if the scan results for the current AP are not
available to check the RSNE/RSNXE in EAPOL-Key msg 3/4.
Signed-off-by: Jouni Malinen <j@w1.fi>
Avoid printing confusing FT debug entries from wpa_sm_set_ft_params()
when FT is not actually used for the connection.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use the same reason code to indicate that IE different in 4-way
handshake and also print a hexdump of RSNXE in both Beacon/ProbeResp and
EAPOL-Key msg 3/4 in the log.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter rsne_override_eapol can now be
used similarly to the previously added rsnxe_override_eapol to override
(replace contents or remove) RSNE in EAPOL-Key msg 3/4. This can be used
for station protocol testing to verify sufficient checks for RSNE
modification between the Beacon/Probe Response frames and EAPOL-Key msg
3/4.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previous implementation was determining whether the override value was
set based on its length being larger than zero. Replace this with an
explicit indication of whether the parameter is set to allow zero length
replacement, i.e., remove of RSNXE from EAPOL-Key msg 3/4.
In addition, move IE replacement into a more generic helper function to
allow this to be used with other IEs as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
The 4-address frames WDS design in mac80211 uses VLAN interfaces
similarly to the way VLAN interfaces based on VLAN IDs are used. The EAP
authentication case ended up overriding the WDS specific assignment even
when the RADIUS server did not assign any specific VLAN for the STA.
This broke WDS traffic.
Fix this by skipping VLAN assignment to VLAN ID 0 for STAs that have
been detected to use 4-address frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
The resource-load-started cannot be used to replace the older
resource-request-starting signal and as such, the final redirect to the
special http://localhost:12345/ URL did not work. Use the decide-policy
signal for navigation action instead.
Also remove the attempt to modify the request URI from
resource-load-started since that is not going to work either. This is
not really critical for functionality, but could eventually be replaced
with a handler for the WebKitWebPage send-request signal.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_tdls_set_key() did set the key_id to -1 to avoid a useless
NL80211_CMD_SET_KEY call that the updated nl80211 driver no longer
carries out. Remove the no longer required workaround.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
After a radar signal is detected, the AP should switch to another
channel, but in the case of 80+80 MHz, channel switch failed because
hostapd did not select the secondary channel in the process. Fix this by
selecting a secondary channel in the case of 80+80 MHz.
Signed-off-by: Xin Wang <xwangw@codeaurora.org>
Signed-off-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
The initial implementation of the PTK derivation workaround for
interoperability with older OWE implementations forced
WPA_KEY_MGMT_PSK_SHA256 to be used for all of PTK derivation. While that
is needed for selecting which hash algorithm to use, this was also
changing the length of the PTK components and by doing so, did not
actually address the backwards compatibility issue.
Fix this by forcing SHA256 as the hash algorithm in PTK derivation
without changing the PTK length calculation for OWE when
owe_ptk_workaround is enabled.
Fixes: 65a44e849a ("OWE: PTK derivation workaround in AP mode")
Fixes: 8b138d2826 ("OWE: PTK derivation workaround in STA mode")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Migrate nl80211 driver to key_flag API and add additional sanity checks.
I'm still not sure why we install unicast WEP keys also as default
unicast keys. Based on how I understand how mac80211 handles that it
should be pointless. I just stuck to how we do things prior to the patch
for WEP keys to not break anything. After all other drivers may need it.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Always report an error when NL80211_CMD_SET_KEY can't set a key to
default.
The old ioctl-based design used a single command to add, set, and delete
a key and had to ignore ENOENT for key deletions. It looks like that
special handling was also ported for NL80211_CMD_NEW_KEY and
NL80211_CMD_SET_KEY instead only for NL80211_CMD_DEL_KEY.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Calling NL80211_CMD_NEW_KEY with NL80211_KEY_DEFAULT_TYPES attributes is
pointless. The information is not expected and therefore the kernel
never forwards it to the drivers. That attribute is used with
NL80211_CMD_SET_KEY.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Allow to abort key installations with different error codes and fix one
misleading return code.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Turns out we are sometime providing a seq when deleting the key. Since
that makes no sense on key deletion let's stop forwarding that to the
driver at least.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Add masks for each key type to define which flags can be combined and
add a helper function to validate key_flag values.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
I decided to drop KEY_FLAG_MODIFY instead of allowing flag combinations not
yet used in the code and will simply recreate it with the Extended Key
ID patches once we get there. For that reason I also did not renumber
the flags.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
hostapd_broadcast_wep_set() can be called without a WEP key set.
Don't try to install a default key in that case.
This patch is not critical for the new API. With key_flag we just would
report an (ignored) error and do nothing. With the patch we simply do
nothing.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The unicast parameter in set_wep_key() is only expected to be set to 0
or 1. Without this patch we set unicast to 0x80 instead of 1. Since
unicast is used as boolean that is working fine but violates the
documented API.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
This clears the AuthorizedMACs advertisement immediately when the
Selected Registrar timeout is hit and no more active PINs are present.
Previously, the AuthorizedMACs advertisement could remain in place
indefinitely since expired PINs were removed only when actually trying
to find a PIN for a new WPS exchange.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it easier to understand what is happening when a new channel
needs to be selected based on a radar detection event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Upon radar detection we used to search channels with the same bandwidth.
This way we might not find any other channels. If there are no channels
available with that bandwidth the AP service will be stopped. To avoid
this problem, also search a suitable channel by downgrading the
bandwidth. This scenario is applicable during CAC as well.
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
In the normal case hostapd_disable_iface() and hostapd_enable_iface()
will be done while switching to another DFS channel upon radar
detection. In certain scenarios radar detected event can come while
hostapd_disable_iface() is in progress and iface->current_mode will be
NULL in that scenario. Previously, we did not check for this scenario
and proceeded with the radar detection logic which can trigger a
segmentation fault. To fix this, avoid proceeding the radar detection
event if iface->current_mode is NULL.
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
The commit a34ca59e (SAE: Allow SAE password to be configured separately
(STA)) added sae_password configuration option. We should also consider
sae_password in the wpa_config_write() function which stores the valid
network block details to an external database.
Fixes: a34ca59e4d ("SAE: Allow SAE password to be configured separately (STA)")
Signed-off-by: Sachin Shelke <sachin.shelke@nxp.com>
Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
There is no support for using the control port for sending out EAPOL
frames through privsep yet, so mask out this capability to fall back to
the l2_packet based design.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add support for element defragmentation as defined in IEEE
P802.11-REVmd/D3.0, 10.28.12 (Element defragmentation).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
IEEE P802.11az/D2.0 renamed the FILS Wrapped Data element,
removing the FILS prefix. Change the code accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
To support PASN authentication flow, where Authentication frames are
sent by wpa_supplicant using the send_mlme() callback, modify the logic
to also send EVENT_TX_STATUS for Authentication frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
PASN authentication can be performed while a station interface is
connected to an AP. To allow sending PASN frames while connected, extend
the send_mlme() driver callback to also allow a wait option. Update the
relevant drivers and wpa_supplicant accordingly.
hostapd calls for send_mlme() are left unchanged, since the wait option
is not required there.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
If the driver requires external SAE authentication, it would result in
registration for all Authentication frames, so even non-SAE
Authentication frames might be forwarded to user space instead of being
handled internally. Fix this by using a more strict match pattern,
limiting the registration to the SAE authentication algorithm only.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
WEP provisioning was removed from WPS v2, so this workaround
functionality has not been applicable. Remove it completely.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was already supported in the offload ACS case and this commit
completes support for this with the internal ACS algorithm.
Signed-off-by: Neo Jou <neojou@gmail.com>
Set iface->current_mode and iface->conf->hw_mode when completing ACS
based on the selected channel in the hw_mode=any case.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
Add suitable channel frequencies from all modes into the scan parameters
when a single mode is not specified for ACS. This is preparation for
being able to support hw_mode=any to select the best channel from any
supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
While the users of os_random() do not really need strong pseudo random
numebrs, there is no significant harm in seeding random() with data from
os_get_random(), i.e., /dev/urandom, to get different sequence of not so
strong pseudo random values from os_random() for each time the process
is started.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since SAE PMK can be updated only by going through a new SAE
authentication instead of being able to update it during an association
like EAP authentication, do not allow PMKSA entries to be used for
caching after the reauthentication threshold has been reached. This
allows the PMK to be updated without having to force a disassociation
when the PMK expires if the station roams between the reauthentication
threshold and expiration timeout.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Since SAE PMK can be updated only by going through a new SAE
authentication instead of being able to update it during an association
like EAP authentication, do not allow PMKSA entries to be used for OKC
after the reauthentication threshold has been reached. This allows the
PMK to be updated without having to force a disassociation when the PMK
expires if the station roams between the reauthentication threshold and
expiration timeout.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
SAE authentication derives PMKID differently from the EAP cases. The
value comes from information exchanged during SAE authentication and
does not bind in the MAC addresses of the STAs. As such, the same PMKID
is used with different BSSIDs. Fix both the hostapd and wpa_supplicant
to use the previous PMKID as is for OKC instead of deriving a new PMKID
using an incorrect derivation method when using an SAE AKM.
This fixes use of opportunistic key caching with SAE.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wpa_ctrl.h can be installed separately with libwpa_client, so
utils/common.h won't be available to its users.
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Add an attribute QCA_WLAN_VENDOR_ATTR_SCAN_DWELL_TIME for specifying
dwell time in the QCA vendor scan command. This is a common value which
applies across all frequencies requested in the scan.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This attribute enables/disables the host driver to send roam reason
information in the Reassociation Request frame to the AP in the same
ESS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Couple of the attributes were defined with inconsistent prefix in the
name (missing "CONFIG_"). Fix these to use the common prefix for all
enum qca_wlan_vendor_attr_config values. Add defined values for the
incorrect names to avoid issues with existing users.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new capability flag based on the nl80211 feature advertisement and
start using the new default key type for Beacon protection. This enables
AP mode functionality to allow Beacon protection to be enabled. This is
also enabling the previously added ap_pmf_beacon_protection_* hwsim test
cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The cookie values for UDP control interface commands was defined as a
static global array. This did not allow multi-BSS test cases to be
executed with UDP control interface. For example, after
hapd1 = hostapd.add_bss(apdev[0], ifname1, 'bss-1.conf')
hapd2 = hostapd.add_bss(apdev[0], ifname2, 'bss-2.conf')
hapd1->ping() did not work.
Move those cookie values to per-instance location in struct
hapd_interfaces and struct hostapd_data to fix this.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Rekeying a pairwise key using only keyid 0 (PTK0 rekey) has many broken
implementations and should be avoided when using or interacting with
one. The effects can be triggered by either end of the connection and
range from hardly noticeable disconnects over long connection freezes up
to leaking clear text MPDUs.
To allow affected users to mitigate the issues, add a new configuration
option "wpa_deny_ptk0_rekey" to replace all PTK0 rekeys with fast
reconnects.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Rekeying a pairwise key using only keyid 0 (PTK0 rekey) has many broken
implementations and should be avoided when using or interacting with
one. The effects can be triggered by either end of the connection and
range from hardly noticeable disconnects over long connection freezes up
to leaking clear text MPDUs.
To allow affected users to mitigate the issues, add a new hostapd
configuration option "wpa_deny_ptk0_rekey" to replace all PTK0 rekeys
with disconnection. This requires the station to reassociate to get
connected again and as such, can result in connectivity issues as well.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The CAN_REPLACE_PTK0 flag provided by nl80211 can be used to detect if
the card/driver is explicitly indicating capability to rekey STA PTK
keys using only keyid 0 correctly.
Check if the card/driver supports it and make the status available as a
driver flag.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The MBO PMF check for AP SME in the driver case was added into a
location that is skipped for WPS processing. That was not really the
correct place for this since the skip_wpa_check label was supposed to
remain immediately following the WPA checks. While this does not really
have much of a practical impact, move the check around so that the
skip_wpa_check label remains where it is supposed to be.
Fixes: 4c572281ed ("MBO: Mandate use of PMF for WPA2+MBO association (AP)")
Signed-off-by: Jouni Malinen <j@w1.fi>
Save RM enabled capability element of an associating station when
hostapd use the device AP SME similarly to how this information is saved
with SME-on-hostapd cases. This allows radio measurement operations
(e.g., REQ_BEACON) to be used.
Signed-off-by: Ouden <Ouden.Biz@gmail.com>
This element is not used in Beacon or Probe Response frames (which is
the reason why the standard does not indicate where exactly it would be
in those frames..); HT Operation element has this information and so
does Extended CSA element.
In practice, this reverts the functionality added in commit 76aab0305c
("Add secondary channel IE for CSA").
Signed-off-by: Jouni Malinen <j@w1.fi>
Hardcoded CONFIG_IEEE80211N to be included to clean up implementation.
More or less all new devices support IEEE 802.11n (HT) and there is not
much need for being able to remove that functionality from the build.
Included this unconditionally to get rid of one more build options and
to keep things simpler.
Signed-off-by: Jouni Malinen <j@w1.fi>
Split the IEs from WPA authenticator state machine into separately added
IEs so that the exact location between these and other elements can be
controlled. This fixes the location of MDE and RSNXE in Beacon and Probe
Response frames. In addition, this swaps the order of BSS Load and RM
Enabled Capabilities elements in Beacon frames to get them into the
correct order (which was already used for Probe Response frames).
Furthermore, this fixes the buffer end checks for couple of elements to
make the implementation more consistent (though, in practice, there is
no impact from this since the old size limit was smaller than needed,
but still sufficiently large to have room for these).
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a new wpa_supplicant network profile configuration parameter
beacon_prot=<0/1> to allow Beacon protection to be enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new hostapd configuration parameter beacon_prot=<0/1> to allow
Beacon protection to be enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
nla_nest_start() might fail, so need to check its return value similarly
to all the other callers.
Fixes: a84bf44388 ("HE: Send the AP's OBSS PD settings to the kernel")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously only couple of AKM suite selectors were converted into
NL80211_ATTR_AKM_SUITES. Add rest of the AKM suites here. However, since
the current kernel interface has a very small limit
(NL80211_MAX_NR_AKM_SUITES = 2), add the attribute only when no more
than that limit entries are included. cfg80211 would reject the command
with any more entries listed.
This needs to be extended in cfg80211/nl80211 in a backwards compatible
manner, so this seems to be the best that can be done for now in user
space. Many drivers do not use this attribute, so must not reject the
configuration completely when larger number of AKM suites is configured.
Such cases may not work properly with drivers that depend on
NL80211_ATTR_AKM_SUITES value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to work around a missing attribute that would cause
cfg80211 to reject some nl80211 commands (e.g.,
NL80211_ATTR_VENDOR_DATA) with new kernel versions that enforce netlink
attribute policy validation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use a single block each for webkit and webkit2 signal handlers. This
cleans up browser.c to have clear sections for each webkit API version.
Signed-off-by: Jouni Malinen <j@w1.fi>
Avoid unnecessary warnings from webkit on calling gtk_main_quit() more
than once for a single gtk_main() call. This is also fixing an issue for
a corner case where the very first URL has special purpose (osu:// or
http://localhost:12345).
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation of hovering-over-link signal handler did not
really work with webkit2, so replace this with mouse-target-changed
handler.
Signed-off-by: Jouni Malinen <j@w1.fi>
hs20_web_browser() was previously hardcoded to not perform strict TLS
server validation. Add an argument to this function to allow that
behavior to be configured. The hs20-osu-client users are still using the
old behavior, i.e., not validating server certificates, to be usable for
testing purposes.
Signed-off-by: Jouni Malinen <j@w1.fi>
SM Power Save was described in somewhat unclear manner in IEEE Std
802.11n-2009 as far the use of it locally in an AP to save power. That
was clarified in IEEE Std 802.11-2016 to allow only a non-AP STA to use
SMPS while the AP is required to support an associated STA doing so. The
AP itself cannot use SMPS locally and the HT Capability advertisement
for this is not appropriate.
Remove the parts of SMPS support that involve the AP using it locally.
In practice, this reverts the following commits:
04ee647d58 ("HT: Let the driver advertise its supported SMPS modes for AP mode")
8f461b50cf ("HT: Pass the smps_mode in AP parameters")
da1080d721 ("nl80211: Advertise and configure SMPS modes")
Signed-off-by: Jouni Malinen <j@w1.fi>
Set the proper bits inside the extended capabilities field to indicate
support for TWT responder.
Tested-by: John Crispin <john@phrozen.org>
Signed-off-by: Mikhail Karpenko <karpenko@fastmail.com>
The HE Operation field for BSS color consists of a disabled, a partial,
and 6 color bits. The original commit adding support for BSS color
considered this to be a u8. This commit changes this to the actual
bits/values.
This adds an explicit config parameter for the partial bit. The disabled
is set to 0 implicitly if a bss_color is defined.
Interoperability testing showed that stations will require a BSS color
to be set even if the feature is disabled. Hence the default color is 1
when none is defined inside the config file.
Signed-off-by: John Crispin <john@phrozen.org>
Commit 2bab073dfe ("WPS: Add new PSK entries with wps=1 tag") added
this when writing the new entry into a file, but the in-memory update
did not get the tag. Add it there as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
Now that hostapd wpa_psk_file has a new tag for identifying PSKs that
can be used with WPS, add that tag to new entries for PSKs from WPS.
This makes it clearer where the PSK came from and in addition, this
allows the same PSK to be assigned if the same Enrollee goes through WPS
provisioning again.
Signed-off-by: Jouni Malinen <j@w1.fi>
By default, when configuration file set wpa_psk_file, hostapd generated
a random PSK for each Enrollee provisioned using WPS and appended that
PSK to wpa_psk_file.
Changes that behavior by adding a new step. WPS will first try to use a
PSK from wpa_psk_file. It will only try PSKs with wps=1 tag.
Additionally it'll try to match enrollee's MAC address (if provided). If
it fails to find an appropriate PSK, it falls back to generating a new
PSK.
Signed-off-by: Tomasz Jankowski <tomasz.jankowski@plume.com>
In the function owe_assoc_req_process(), values assigned to the reason
argument imply that it should be renamed to status. Rename 'reason' to
'status' and modify the uses of owe_assoc_req_process() accordingly.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
This commit adds new attributes for getting the Probe Response frame
IEs, Beacon frame IEs and the disconnection reason codes through
get_sta_info vendor command.
The host driver shall give this driver specific reason code through
the disconnection reason code attribute
QCA_WLAN_VENDOR_ATTR_GET_STA_DRIVER_DISCONNECT_REASON.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This acts as an event from the host driver to the user space to notify
the driver specific reason for a disconnection. The host driver
initiates the disconnection for various scenarios (beacon miss, Tx
Failures, gateway unreachability, etc.) and the reason codes from
cfg80211_disconnected() do not carry these driver specific reason codes.
Host drivers should trigger this event immediately prior to triggering
cfg80211_disconnected() to allow the user space to correlate the driver
specific reason code with the disconnect indication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This acts as a vendor event and is used to update the information
of a station from the driver to userspace.
Add an attribute for the driver to update the channels scanned in
the last connect/roam attempt.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Some of the operating classes added in the 6 GHz band have a larger
number of channels included in them (e.g., operating class 131 has 59
channels). Increase the maximum number of channels per operating class
so that all channels will get populated.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This attribute aims to configure the STA to send the Beacon Report
Response with failure reason for the scenarios where the Beacon Report
Request cannot be handled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This ugly hack for being able to search for optional arguments with
space before them was quite inconvenient and unexpected. Clean this up
by handling this mess internally with a memory allocation and string
duplication if needed so that the users of wpa_supplicant control
interface do not need to care about such details.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
As qca_vendor.h alone can be included by other applications, define
macro BIT() in qca_vendor.h itself if not yet defined, e.g., by
including utils/common.h before qca_vendor.h.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wlantest build did not define build options to determine key management
values for SAE, OWE, and DPP. Add those and the needed SHA512 functions
to be able to decrypt sniffer captures with PMK available from an
external source.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
(Re)Association Response frames should include radio measurement
capabilities in order to let stations know if they can, e.g., use
neighbor requests.
I tested this commit with a Samsung S8, which does not send neighbor
requests without this commit and sends them afterwards.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
A driver supports FT if it either supports SME or the
NL80211_CMD_UPDATE_FT_IES command. When selecting AKM suites,
wpa_supplicant currently doesn't take into account whether or not either
of those conditions are met. This can cause association failures, e.g.,
when an AP supports both WPA-EAP and FT-EAP but the driver doesn't
support FT (wpa_supplicant will decide to do FT-EAP since it is unaware
the driver doesn't support it). This change allows an FT suite to be
selected only when the driver also supports FT.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
The new sae_pwe=3 mode can be used to test non-compliant behavior with
SAE Password Identifiers. This can be used to force use of
hunting-and-pecking loop for PWE derivation when Password Identifier is
used. This is not allowed by the standard and as such, this
functionality is aimed at compliance testing.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This was not supposed to set the constructed bit in the header. Fix this
to avoid parsing issues with other ASN.1 DER parsers.
Fixes: c025c2eb59 ("DPP: DPPEnvelopedData generation for Configurator backup")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make Configurator provisioning require explicit conf parameter enabling
similarly to the previously used conf=ap-* and conf=sta-* cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This avoids unexpected behavior if GAS query fails and the Config
Response does not get processed at all. Previously, this could result in
configuration being assumed to be successful instead of failure when
Config Response object was not received at all. That could result in
undesired Config Result frame transmission with DPP Rel 2 and not
clearing the ongoing DPP session.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, unexpected Authentication Confirm messages were ignored in
cases where no Authentication Confirm message was expected at all, but
if this message was received twice in a state where it was expected, the
duplicated version was also processed. This resulted in unexpected
behavior when authentication result was processed multiple times (e.g.,
two instances of GAS client could have been started).
Fix this by checking auth->waiting_auth_conf before processing
Authetication Confirm. That boolean was already tracked, but it was used
only for other purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Only one peer-commit-scalar value was stored for a specific STA (i.e.,
one per MAC address) and that value got replaced when the next SAE
Authentication exchange was started. This ended up breaking the check
against re-use of peer-commit-scalar from an Accepted instance when
anti-clogging token was requested. The first SAE commit message (the one
without anti-clogging token) ended up overwriting the cached
peer-commit-scalar value while leaving that instance in Accepted state.
The second SAE commit message (with anti-clogging token) added ended up
getting rejected if it used the same value again (and re-use is expected
in this particular case where the value was not used in Accepted
instance).
Fix this by using a separate pointer for storing the peer-commit-scalar
value that was used in an Accepted instance. There is no need to
allocate memory for two values, i.e., it is sufficient to maintain
separate pointers to the value and move the stored value to the special
Accepted state pointer when moving to the Accepted state.
This fixes issues where a peer STA ends up running back-to-back SAE
authentication within couple of seconds, i.e., without hostapd timing
out the STA entry for a case where anti-clogging token is required.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, hostapd ignored the secondary channel provided by ACS if
both HT40+ and HT40- are set in hostapd.conf. This change selects such
channel for HT40 if it's valid, which is more reasonable.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The internal WMM AC parameters use just the exponent of the CW value,
while nl80211 reports the full CW value. This led to completely bogus
CWmin/CWmax values in the WMM IE when a regulatory limit was present.
Fix this by converting the value to the exponent before passing it on.
Fixes: 636c02c6e9 ("nl80211: Add regulatory wmm_limit to hostapd_channel_data")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
nl80211 uses a different queue mapping from hostap, so AC indexes need
to be converted.
Fixes: 636c02c6e9 ("nl80211: Add regulatory wmm_limit to hostapd_channel_data")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The size of a single route(4) message cannot be derived from
either the size of the AF_INET or AF_INET6 routing tables.
Both could be empty or very large.
As such revert back to a buffer size of 2048 which mirrors
other programs which parse the routing socket.
Signed-off-by: Roy Marples <roy@marples.name>
Now that both hostapd and wpa_supplicant react to interface flag
changes, there is no need to set or remove IFF_UP.
It should be an administrative flag only.
Signed-off-by: Roy Marples <roy@marples.name>
There is little point in having both and it brings interface
addition/removal and IFF_UP notifications to hostapd.
Signed-off-by: Roy Marples <roy@marples.name>
When external authentication is used, the station send mlme frame (auth)
to the driver may not be able to get the frequency (bss->freq) after
hostap.git commit b6f8b5a9 ("nl80211: Update freq only when CSA
completes"). Use the assoc_freq to send the MLME frame when SAE external
authentication is used to avoid this issue.
Signed-off-by: Ouden <Ouden.Biz@gmail.com>
This commit introduces additional stats to query through
QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds support for generating an encrypted backup of the local
Configurator information for the purpose of enrolling a new
Configurator. This includes all ASN.1 construction and data encryption,
but the configuration and connector template values in
dpp_build_conf_params() are not yet complete.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process the received DPPEnvelopedData when going through Configurator
provisioning as the Enrollee (the new Configurator). This parses the
message, derives the needed keys, and decrypts the Configurator
parameters. This commit stores the received information in
auth->conf_key_pkg, but the actually use of that information to create a
new Configurator instance will be handled in a separate commit.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
There is no need for the Protocol Version attribute in Authentication
Response if the peer is a DPP R1 device since such device would not know
how to use this attribute. To reduce risk for interoperability issues,
add this new attribute only if the peer included it in Authentication
Request.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an attribute QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY_FREQUENCY for
primary channel center frequency in the definition for Representative
Tx Power List (RTPL) list entry instance. This is required for 6 GHz
support, since the 6 GHz channel numbers overlap with existing 2.4 GHz
and 5 GHz channel numbers thus requiring frequency values to uniquely
identify channels.
Mark QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY as deprecated if both the
driver and user space application support 6 GHz. For backward
compatibility, QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY is still used if
either the driver or user space application or both do not support the
6 GHz band.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The recent addition of the X.509v3 certificatePolicies parser had a
copy-paste issue on the inner SEQUENCE parser that ended up using
incorrect length for the remaining buffer. Fix that to calculate the
remaining length properly to avoid reading beyond the end of the buffer
in case of corrupted input data.
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=20363
Fixes: d165b32f38 ("TLS: TOD-STRICT and TOD-TOFU certificate policies")
Signed-off-by: Jouni Malinen <j@w1.fi>
Make the selected channel available for upper layer software to use,
e.g., when starting DPP listen operation during NFC negotiated
connection handover.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new control interface commands "DPP_NFC_HANDOVER_REQ own=<id>
uri=<URI>" and "DPP_NFC_HANDOVER_SEL own=<id> uri=<URI>" to support NFC
negotiated connection handover. These commands are used to report a DPP
URI received from a peer NFC Device in Handover Request and Handover
Select messages. The commands return peer bootstrapping information ID
or FAIL on failure. The returned ID is used similarly to any other
bootstrapping information to initiate DPP authentication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new dpp_gen_uri() helper function can be used to build the
bootstrapping URI from locally stored information. This can be used to
make it easier to update the URI, e.g., for NFC negotiated connection
handover cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This increases the limit of how many data fragments can be supported
with the internal HMAC implementation. The previous limit was hit with
some FT use cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit introduces the vendor event
QCA_NL80211_VENDOR_SUBCMD_REQUEST_SAR_LIMITS_EVENT.
Host drivers can request user space application to set SAR power
limits with this event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new QCA vendor attribute to set thermal level to the driver from
userspace. The driver/firmware takes actions requested by userspace to
mitigate high temperature such as throttling TX etc. The driver may
choose the level of throttling and other actions for various thermal
levels set by userspace.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
