Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
reports mesh peer AID to kernel.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This allows P2P Listen to be offloaded to device to enhance power
saving.
To start P2P listen offload, from wpa_cli interface, issue the command:
p2p_lo_start <freq> <period> <interval> <count>
To stop P2P listen offload, issue the command:
p2p_lo_stop
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of number of sparse warnings and also allows the
compatibility of the declarations to be verified (number of missing
const declarations are fixed here as well).
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds the necessary changes to support extraction and use of the
extended capabilities specified per interface type (a recent
cfg80211/nl80211 extension). If that information is available,
per-interface values will be used to override the global per-radio
value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new "timeout" argument to the event message if the nl80211 message
indicates that the connection failure is not due to an explicit AP
rejection message. This makes it easier for external programs to figure
out why the connection failed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This flag indicates that RRM can be used in (Re)Association Request
frames, without supporting quiet period.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Add a new function declaration that will allow wpa_supplicant to request
the driver to configure data frame filters for specific cases.
Add definitions that will allow frame filtering for stations as
required by Hotspot 2.0:
1. Gratuitous ARP
2. Unsolicited NA
3. Unicast IP packets encrypted with GTK
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
If a legacy client with no P2P PS support is trying to connect to
a P2P GO, the driver should know that, and change its PS behavior
accordingly.
Add a parameter to hostapd_sta_add_params() indicating if P2P PS is
supported by the station and pass this parameter to kernel with nl80211
driver when the station is added/set.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Interface additions/removals are not guaranteed to be for the driver
listening to the kernel events. As such, send the events to
wpa_supplicant_event_global() which can then pick the correct interface
registered with wpa_supplicant to send the event to.
Signed-off-by: Roy Marples <roy@marples.name>
If the driver supports 64-bit TX/RX byte counters, use them directly.
The old 32-bit counter extension is maintained for backwards
compatibility with older drivers.
For nl80211 driver interface, the newer NL80211_STA_INFO_RX_BYTES64 and
NL80211_STA_INFO_TX_BYTES64 attributes are used when available. This
resolves the race vulnerable 32-bit value wrap/overflow. Rework RADIUS
accounting to use these for Acct-Input-Octets, Acct-Input-Gigawords,
Acct-Output-Octets, and Acct-Output-Gigawords, these values are often
used for billing purposes.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
This provides means for determining whether the driver supports full AP
station state and setting the needed STA flags for using this
functionality.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.
Add a pbss flag to the relevant structures to support starting a PCP and
connecting to a PCP. Implement support in the nl80211 driver by using
the new PBSS flag attribute.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Need to include these headers in C++ files for adding a binder interface
to wpa_supplicant. So, fix the following C++ compiler errors in them:
1. Add explicit C-style casts in wpa_buf.h header.
2. Move the nested definition of wpa_driver_scan_ssid in driver.h
outside of wpa_driver_scan_params because it is used in another
structure below.
Signed-off-by: Roshan Pius <rpius@google.com>
Add 'scan plans' to driver scan parameters for scheduled scan.
Each 'scan plan' specifies the number of iterations to run the scan
request and the interval between iterations. When a scan plan
finishes (i.e., it was run for the specified number of iterations),
the next scan plan is executed. The last scan plan will run
infinitely.
The maximum number of supported scan plans, the maximum number of
iterations for a single scan plan and the maximum scan interval
are advertised by the driver.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This adds the driver interface commands for issuing a request to abort
an ongoing scan operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the previous design that covered only the VHT 80 MHz cases
for VHT channel flags. New functions are introduced to allow 160 MHz
bandwidth cases to determine the center channel and check availability
of a 160 MHz channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When an AP interface it created, it is also setup and subscribes
for management frames etc. However, when the interface is added by
wpa_supplicant, setting up for AP operations is redundant because
it will be done by wpa_supplicant on wpa_drv_init() when setting
the interface mode to AP.
In addition, it may cause wpa_supplicant to fail initializing the
interface as it will try to subscribe for management frames on this
interface but the interface is already registered.
Change this, so when adding an AP interface, make setting up the AP
optional, and use it only when the interface is added by hostapd but not
when it is added by wpa_supplicant.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This allows offloaded roaming to inform user space of the change in IP
subnet post roaming. The device may have roamed to a network which is in
a different subnet which will result in IP connectivity loss. Indicating
the change in subnet enables the user space to refresh the IP address or
to perform IP subnet validation if unknown status is indicated.
The driver indication is reported with a new event from wpa_supplicant
in the following format:
CTRL-EVENT-SUBNET-STATUS-UPDATE status=<0/1/2>
where
0 = unknown
1 = IP subnet unchanged (can continue to use the old IP address)
2 = IP subnet changed (need to get a new IP address)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some management frames contain CSA counters which should be updated by
kernel. Change driver op send_mlme() allowing to send a frame,
specifying an array of offsets to the CSA counters which should be
updated. For example, CSA offsets parameters should be specified when
sending Probe Response frames during CSA period.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Channel switch may be performed using both CSA and eCSA IEs together.
This may happen, for example with a P2P GO on band A with legacy
clients. Extend driver API to support up to 2 CSA counters.
This patch also includes the required implementation for nl80211.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Allow wpa_supplicant to use vendor scan (if supported by the driver)
together with the normal nl80211 scan and handling external scan events.
Since this results in possibility of concurrent scan operations, some of
the operations related to scan results need to check more carefully when
an event is relevant for a specific interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the QCA vendor specific nl80211 interface to query the preferred
frequency list from driver and add a new wpa_cli command to query this
information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Upon GO Negotiation completion, if the remote peer becomes GO, send a
hint event over QCA vendor specific interface to inform the driver of
the likely operating channel of the P2P GO.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the nl80211 interface command "driver status" to retrieve the
concurrency capabilities from the driver using the QCA vendor
extensions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When ACS is offloaded to device driver and the hw_mode parameter is set
to any, the current_mode structure is NULL which fails the ACS command.
Fix this by populating the ACS channel list with channels from all bands
when current_mode is NULL.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add vendor command to pass SET setband command to the driver and read
the updated channel list from driver when this notification succeeds.
This allows the driver to update its internal channel lists based on
setband configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Change send_mlme() API to allow sending management frames on a specific
channel, overriding the internal driver decision.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When device supports dual band operations with offloaded ACS, hw_mode
can now be set to any band (hw_mode=any) in order to allow ACS to select
the best channel from any band. After a channel is selected, the hw_mode
is updated for hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Update ACS driver offload feature for VHT configuration. In addition,
this allows the chanlist parameter to be used to specify which channels
are included as options for the offloaded ACS case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the TDLS operation request mechanism to allow TDLS
Discovery Request to be initiated by the driver similarly to the
existing Setup and Teardown requests.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This modifies the BSS selection routines to calculate SNR and estimated
throughput for each scan result and then use the estimated throughput as
a criteria for sorting the results. This extends the earlier design by
taking into account higher throughput rates if both the AP and local
device supports HT20, HT40, or VHT80. In addition, the maximum rate is
restricted based on SNR.
In practice, this gives significantly higher probability of selecting
HT/VHT APs when there are multiple BSSes in the same ESS and SNR is not
low enough to prevent higher MCS use.
Signed-off-by: Jouni Malinen <j@w1.fi>
Read p2p_go_ctwindow (0-127 TUs) from the config file, and pass it to
the driver on GO start.
Use p2p_go_ctwindow=0 (no CTWindow) by default.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Add fixed_freq=<0/1> network block parameter and pass it to the driver
when starting or joining an IBSS. If this flag is set, IBSS should not
try to look for other IBSS networks to merge with on different channels.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
When DFS offloading capability is supported by the driver, the driver
should use these events to indicate when a radar pattern has been
detected, channel availability check (CAC) has been completed, aborted
or finished after the non-occupancy period is over on a DFS channel.
Also, add a new driver.h event to be used by NL80211 to indicate CAC
Started event on a DFS channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a step towards enabling hostapd to restart AP mode functionality
if the interface is disabled and re-enabled, e.g., with ifconfig down
and up. This commit takes care of beaconining only which may be
sufficient for open mode connection, but not for WPA2 cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This modifies struct wpa_ptk to allow the length of KCK and KEK to be
stored. This is needed to allow longer keys to be used, e.g., with
Suite B 192-bit level.
Signed-off-by: Jouni Malinen <j@w1.fi>
Current mesh code uses ap_max_inactivity as inactivity timer. This patch
makes it configurable.
There is another mesh inactivity timer in mac80211. The timer works even
if user_mpm=1. So this patch sets the max value to the timer for
workaround.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Add WPA_DRIVER_FLAGS_HT_IBSS driver feature flag. Some drivers could not
set this feature and next could fail when we will enable HT support for
IBSS with error message: nl80211: Join IBSS failed: ret=-22 (Invalid
argument).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
cfg80211 dropped support for tracking BSS authentication state and
setting NL80211_BSS_STATUS_AUTHENTICATED in 'cfg80211: stop tracking
authenticated state' three years ago (starting in Linux 3.4). As such,
this workaround code in wpa_supplicant cannot be reached anymore. There
is no real need for maintaining it for older kernels either, since there
are other ways of detecting and working around state mismatches with the
actual authentication operations failing.
Signed-off-by: Jouni Malinen <j@w1.fi>
1. Add parameters to the scan command to allow MAC address
randomization during scan and scheduled scan.
2. Add capability bits to publish MAC address randomization support
in scan and scheduled scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The supplicant code does not try to control the actual channel of the
radio at any point. It simply passes the target peer and channel
parameters to the driver. It's the driver's responsibility to
periodically initiate TDLS channel-switch operations when TDLS
channel-switching is enabled.
Allow enable/disable operations to be invoked via the control interface.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Maximum number of peer links is maximum number of connecting mesh peers
at the same time. This value is 0..255 based on the
dot11MeshNumberOfPeerings range.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.
This command makes a virtual mesh interface to be used for mesh gate.
This command expects to be used like this.
wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The send_eapol() callback was used by driver_test.c, but with that
removed, there is no remaining users of the alternative EAPOL frame
transmitting mechanism in wpa_supplicant, i.e., all remaining driver
interfaces use l2_packet instead. Remove the send_eapol() to get rid of
unused code.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit introduces a QCA vendor command that allows interrogation of
the vendor-specific features supported by the device/driver. Currently
the only defined feature is the ability to offload key management.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This reduced number of unnecessarily duplicated driver interface
callback functions for sending Action frames by using the more generic
send_action() instead of FT specific send_ft_action().
Signed-off-by: Jouni Malinen <j@w1.fi>
Using QCA vendor command, allow ACS function to be offloaded to the
driver. Once channels are selected, hostapd is notified to perform OBSS
operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd was still providing couple of parameters that were used only in
the already removed driver_test.c framework.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add definitions for RRM (Radio Resource Measurement) support:
1. Flags that specify the RRM capabilities of the underlying driver
2. Flag for RRM in Capability Info field in Management frames
3. Indication in association parameters regarding an RRM connection
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
This allows adding/deleting an IPv6 neighbor entry to/from the bridge,
to which the BSS belongs. This commit adds the needed functionality in
driver_nl80211.c for the Linux bridge implementation. In theory, this
could be shared with multiple Linux driver interfaces, but for now, only
the main nl80211 interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Add add_tx_ts() and del_tx_ts() ops to notify the driver about
TSPEC add / delete.
Additionally, add wmm_ac_supported flag to indicate
whether the driver supports WMM AC.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Add a new option "mesh_ht_mode" that specifies the HT mode for the
mesh, with this option on, mesh beacons, actions frames, and probe
responses with include the appropriate HT information elements.
[original implementation by Chun-Yeow Yeoh <yeohchunyeow@gmail.com>]
[some fixes by Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
New kernels in wiphy_suspend() will call cfg80211_leave_all() that will
eventually end up in cfg80211_stop_ap() unless wowlan_triggers were set.
For now, use the parameters from the station mode as-is. It may be
desirable to extend (or constraint) this in the future for specific AP
mode needs.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This was used in driver_test.c, but that driver wrapper has been removed
and there are no remaining or expected users for EVENT_MLME_RX.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was used in hostapd driver_test.c, but that driver wrapper has been
removed and there are no remaining or expected users for
EVENT_FT_RRB_RX.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows setting a network parameter on the bridge that the BSS
belongs to.
This commit adds the needed functionality in driver_nl80211.c for the
Linux bridge implementation. In theory, this could be shared with
multiple Linux driver interfaces, but for now, only the main nl80211
interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
This allows setting a bridge port attribute. Specifically, the bridge
port in this context is the port to which the BSS belongs.
This commit adds the needed functionality in driver_nl80211.c for the
Linux bridge implementation. In theory, this could be shared with
multiple Linux driver interfaces, but for now, only the main nl80211
interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
This allows adding/deleting an IPv4 neighbor entry to/from the bridge,
to which the BSS belongs. This commit adds the needed functionality in
driver_nl80211.c for the Linux bridge implementation. In theory, this
could be shared with multiple Linux driver interfaces, but for now, only
the main nl80211 interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Add the following channel flags:
* INDOOR_ONLY: The channel can be used if and only if there is a clear
assessment that the device is operating in an indoor environment, i.e.,
it is AC power.
* CONCURRENT_GO: The channel can be used for instantiating a GO if and
only if there is an additional station interface that is currently
connected to an AP on the same channel or on the same U-NII band
(assuming that the AP is an authorized master).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Use the 'no_ir' notation instead of the 'passive scan' and
'no_ibss' notations to match the earlier change in nl80211.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Modify network mode to support mode number 5 when CONFIG_MESH is
enabled.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
This is needed for managing STA entries for mesh use cases.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Add smps_modes field, and let the driver fill it with its supported SMPS
modes (static/dynamic). This will let us start an AP with specific SMPS
mode (e.g., dynamic) that will allow it to reduce its power usage.
Signed-off-by: Eliad Peller <eliad@wizery.com>
This commit introduces a QCA vendor command and event to provide an
option to use extended versions of the nl80211 connect/roam operations
in a way that allows drivers to offload key management operations to the
driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Create init_mesh, mesh_join, and mesh_leave actions to kernel.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Convert the driver flags variable to u64 since there was no room for
more flags.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Use hostapd_freq_params instead of simple frequency parameter for driver
commands. This is preparation for IBSS configuration to allow use of
HT/VHT in IBSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Some drivers need to know the initiator of a TDLS connection in order
to generate a correct TDLS mgmt packet. It is used to determine
the link identifier IE. Pass this information to the driver.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
The network block bssid parameter can be used to force a specific BSS to
be used for a connection. It is also possible to modify this parameter
during an association. Previously, that did not result in any
notification to the driver which was somewhat problematic with drivers
that take care of BSS selection. Add a new mechanism to allow
wpa_supplicant to provide a driver update if the bssid parameter change
for the current connection modifies roaming policy (roaming
allowed/disallowed within ESS).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It's worth giving a try to fallback to re-starting BSSes at least once
hoping it works out instead of just leaving BSSes disabled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Add a new wowlan_triggers option to wpa_supplicant.conf. The triggers in
this key will be used to configure the kernel wowlan configuration.
For now, support only simple flags. More complex triggers can be added
later on.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
This provides information to allow the driver to be configured for
updated channel parameters, e.g., when dynamically changing HT20/HT40
bandwidth.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some trailing whitespace and spaces for indentation were present in the
driver wrapper and header files.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct the
VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the presence
of the respective IEs in the received TDLS Setup Response frame.
The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This uses a QCA vendor extension to determine if the driver supports
fully offloaded DFS operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
At least in nl80211, broadcast management frames like Probe Request
frames, may be processed multiple times per BSS if multi-BSS is active
and NL80211_CMD_FRAME event is used to deliver them. In the case of
Probe Request frames, hostapd will create multiple redundant Probe
Response frames which are problematic when many BSS are on one channel.
This problem is caused by driver_nl80211 generating an event for
wpa_supplicant_event() for each BSS, and hostapd_mgmt_rx() calls
ieee802_11_mgmt() for each BSS, too.
Fix this by processing broadcast events only for the BSS the driver
intended to. The behavior is not changed for drivers not setting a BSS.
Signed-hostap: Simon Wunderlich <simon@open-mesh.com>
wpa_supplicant already allowed beacon interval to be configured for AP
mode operations, but this was not passed to the driver for IBSS even
though the same parameter can used for that case. Add this for the
nl80211 driver interface to allow beacon interval to be controlled for
IBSS as well.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds an option to optimize AP teardown by leaving the
deletion of keys (including group keys) and stations to the driver.
This optimization option should be used if the driver supports stations
and keys removal when stopping an AP.
For example, the optimization option will always be used for cfg80211
drivers since cfg80211 shall always remove stations and keys when
stopping an AP (in order to support cases where the AP is disabled
without the knowledge of wpa_supplicant/hostapd).
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Add a callback to the driver interface that allows vendor specific
commands to be sent. In addition, a control interface command is added
to expose this new interface outside wpa_supplicant:
Vendor command's format:
VENDOR <vendor id> <sub command id> [<hex formatted data>]
The 3rd argument will be converted to binary data and then passed as
argument to the sub command.
This interface is driver independent, but for now, this is only
implemented for the nl80211 driver interface using the cfg80211 vendor
commands.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Many drivers support operation without GTK configured, but most (if any)
today do not advertise this. Handle this by skipping GTK cipher suite
configuration if the driver did not advertise support in order to work
around cfg80211 validation steps.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This uses the new nl80211 attributes to allow the connect command to
provide bssid and freq hints to the driver without limiting roaming to
the specific BSS/frequency. This can be used by drivers that perform
internal BSS selection (WPA_DRIVER_FLAGS_BSS_SELECTION) as a candidate
for initial association.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Commit 795baf773f ('hostapd: Filter
channel list updated events after country code change') uses the
EVENT_CHANNEL_LIST_CHANGED data pointer, but it updated only one of the
callers to provide that data. NL80211_CMD_REG_BEACON_HINT event was
still sending the event without the initiator data and resulted in NULL
pointer dereference, e.g., if a scan was run while hostapd was running
and the driver was in world roaming state and enabled a channel for
active scans.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a QCA vendor specific nl80211 event to allow the driver to
indicate a list of frequency ranges that should be avoided due to
interference or possible known co-existance constraints. Such
frequencies are marked as not allowed for P2P use to force groups to be
formed on different channels.
If a P2P GO is operating on a channel that the driver recommended not to
use, a notification about this is sent on the control interface and
upper layer code may decide to tear down the group and optionally
restart it on another channel. As a TODO item, this could also be changed
to use CSA to avoid removing the group.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's supported channel and operating class
is required for the driver to do TDLS off channel operations with a
compatible peer. Pass this information to the driver when the peer
station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Replace channel_switch_supported flag of the
wpa_driver_nl80211_data by WPA_DRIVER_FLAGS_AP_CSA inside
wpa_driver_capa.flags. It makes more sense and also can
be accessed by wpa_supplicant.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
If the BSS table within wpa_supplicant is flushed, request the driver to
flush its own scan result table during the next scan. This can avoid
unexpected old BSS entries showing up after BSS_FLUSH or FLUSH command
in cases where the driver may maintain its internal cache of scan
results (e.g., cfg80211 BSS table persists at least for 15 seconds).
In addition to doing this automatically on BSS_FLUSH/FLUSH, a new SCAN
command argument, only_new=1, can be used to request a manual scan
request to do same. Though, it should be noted that this maintains the
BSS table within wpa_supplicant. BSS_FLUSH followed by SCAN command can
be used to clear all BSS entries from both the driver and
wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
WPA_CIPHER_* and CIPHER_* are used for the exact same set of cipher
suites with the main difference being that the WPA_CIPHER_* version is
suitable to be used as a bitfield. Similarly, WPA_KEY_MGMT_* and
KEY_MGMT_* have similar design for AKMs. There is no need to maintain
two separate copies of the definitions since the bitfield compatible
version can be used for both needs. Get rid of the CIPHER_* and
KEY_MGMT_* versions to clean up the implementation by getting rid of
unnecessary mapping functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
The option of handling upper layer P2P management operations within the
driver/firmware was originally planned to be used with wpa_supplicant,
but this has not really happened and there is no clear sign of this
being needed in the near term either. This functionality has not been
completed and it is certainly not being kept up-to-date or tested. As
such, it is best to remove it for now and if this or something similar
is needed in the future, it can be brought back once a clear need for it
has been demonstrated first.
Signed-hostap: Jouni Malinen <j@w1.fi>
This driver event was used separately for some Action frames, but all
the driver wrappers converted to this from information that would have
been enough to indicate an EVENT_RX_MGMT event. In addition, the
received event was then converted back to a full IEEE 802.11 management
frame for processing in most cases. This is unnecessary complexity, so
get rid of the extra path and use EVENT_RX_MGMT for Action frames as
well as other management frame subtypes.
Signed-hostap: Jouni Malinen <j@w1.fi>
Action frame RX report through EVENT_RX_ACTION did not indicate whether
the frame was protected or not even though that information is available
in mlme_event_mgmt(). hostapd_rx_action() has a workaround for setting
the protected flag for SA Query frames, but that did not apply for other
frames, like FT Action. This broke FT-over-DS when PMF is enabled with
newer kernel versions (i.e., the ones that do not use monitor interface
for receiving management frames).
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds initial parts for supporting the new GCMP-256, CCMP-256,
BIP-GMAC-128, BIP-GMAC-256, and BIP-CMAC-256 cipher suites.
Signed-hostap: Jouni Malinen <j@w1.fi>
The BSS table, scan timeout, and related functionality should use
monotonic time since they care about relative values (age) only.
Unfortunately, these are all connected, so the patch can't be split
further. Another problem with this is that it changes the driver wrapper
API. Though, it seems only the test driver is using this.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Do not assume the driver supports QoS Mapping, but instead, advertise
support for this only if CONFIG_INTERWORKING is defined and driver
indicates support for configuring QoS Map.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Adds support for VHT by parsing bandwidth and center_freq{1,2}.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This is a mechanism used in Android to extend driver interface in vendor
specific ways. This is included only for the purpose of Android
compatibility. Proper interface commands should be used for any new
functionality.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add csa_settings struct which holds parameters for CSA. Change driver
interface for switch_channel(), so that it will receive this struct and
not only the new frequency as it was before. This allows wpa_supplicant
to provide all the required parameters (beacons, proberesp, assocresp,
CSA IE) which are required by cfg80211 implementation.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
We were not filtering the EVENT_CHANNEL_LIST_CHANGED events based on the
regulatory hint initiator. So wait for EVENT_CHANNEL_LIST_CHANGED event
after our own change was triggered even when regulatory hint initiator
was the driver. This could result in the wait for the channel list to be
updated to be terminated before the real change has occurred and as
such, old channel list remaining in use when configuring
hostapd/wpa_supplicant country parameter. Fix this by filtering the
hints according to the initiator and only regulatory hints initiated by
user will be used to stop the wait.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If hostapd is requested to set the country code and the previous country
code differs from the new one, the channel list information from the
driver may change. This change may not be instant, so wait for an
EVENT_CHANNEL_LIST_CHANGED event before continuing interface setup with
fetching of the channel list information. This fixes issues where the
selected channel is not available based on the previous regulatory data
and update through CRDA takes some time.
Signed-hostap: Jouni Malinen <j@w1.fi>
When removing and re-adding the first wlan# netdev to hostapd
dynamically, the netdev is already present and should not be removed and
re-added to maintain its state as not-added-by-hostapd so that it does
not get removed automatically.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Later on, we'll consider the availability of these
channels when starting P2P GO with VHT support.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Previously the Country element contained the max TX power the local
hardware was capable of. Change this to just use the regulatory limit.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
This allows QoS Map Set element to be added to (Re)Association Response
frames and in QoS Map Configure frame. The QoS Mapping parameters are
also made available for the driver interface.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
STATUS-DRIVER command can now be used to fetch driver interface status
information. This is mainly for exporting low-level driver interface
information for debug purposes.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds ACS support to hostapd. Currently only survey-based
algorithm is available.
To use ACS you need to enable CONFIG_ACS=y in .config and use
channel=0 (or channel=acs_survey) in hostapd.conf.
For more details see wiki page [1] or comments in src/ap/acs.c.
[1]: http://wireless.kernel.org/en/users/Documentation/acs
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
This adds survey dump support for all frequencies
and for specific desired frequencies. This will later
be used by ACS code for spectrum heuristics.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
It is possible that when trying to remove a dynamically added interface,
changing its type to station mode is not possible (since the kernel does
not support so in its interface combinations).
Since P2P interfaces are always dynamically added, avoid changing their
type to station in the deinit_ap() and deinit_p2p_client() nl80211
callbacks, assuming that the interface is about to be removed.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
This is not used anymore after the previous commits that changed the
driver interface to use number of supported concurrent channels instead
of this flag.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
Previously, drivers only reported if they support multiple concurrent
channels, but did not report the maximum number of supported channels.
Add this reporting to the driver capabilities and add the implementation
to driver_nl80211.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
The static WEP keys have to be configured for the new VLAN
interface that is created for a 4addr WDS peer, not doing so
breaks WEP functionality in nl80211/4addr based WDS links.
Signed-hostap: Sujith Manoharan <c_manoha@qca.qualcomm.com>
This allows wpa_supplicant to associate to an AP that has VHT BSS
membership selector set to indicate VHT support is required for the BSS.
Without the patch it was impossible to connect to, e.g., hostapd-based
AP that has require_vht=1. wpa_supplicant was complaining with:
hardware does not support required rate 63.0 Mbps
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Check the supported interfaces attribute to identify support for
a dedicated P2P Device interface type. If set, update the driver
capabilities flag to notify the supplicant.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add AVG_RSSI report to the signal_poll command if it is reported by
the kernel.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
