Make wpas_dbus_handler_interworking_select() conditional on
CONFIG_INTERWORKING to avoid compilation issues.
Fixes: c8e4283f90 ("D-Bus: Interworking network selection")
Signed-off-by: Alex Kiernan <alexk@zuma.ai>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Add the "InterworkingSelect" method to the DBus API to trigger an
Interworking scan with ANQP fetches. When a BSS that matches a
configured credential is found, the result is emitted using the signal
"InterworkingAPAdded". Completion of the full InterworkingSelect
operation is indicated with the "InterworkingSelectDone" signal.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
Add "AddCred", "RemoveCred", and "RemoveAllCreds" methods to the D-Bus
API of the network interface to allow the caller to manipulate a set of
Interworking credentials similarly to the way this was enabled through
the control interface.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
The P2P DBus interface was using the wrong interface name when calling
wpas_p2p_invite_group(). Capture the group interface name before calling
the method to fix this.
Signed-off-by: Hicham Hassoubi <Hicham_hassoubi@bose.com>
Introduce a new allow_6ghz parameter with P2P_CONNECT, P2P_GROUP_ADD,
and P2P_INVITE commands for P2P connection on the 6 GHz channels when
Wi-Fi Display is enabled on both the devices. This commit is only adding
the interface change without changing any actual P2P functionality.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Previously, the 6 GHz channels were disabled for P2P operations.
Introduce a new include_6ghz parameter for the P2P_FIND command to
configure P2P discovery on the 6 GHz channels.
However, the p2p_6ghz_disable parameter in the configuration takes a
higher priority. If the p2p_6ghz_disable parameter is not set in the
configuration, include_6ghz parameter can be used to enable or disable
the discovery operation in the 6 GHz channels for the P2P_FIND command.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
The roam D-Bus and ROAM control itnerface commands flip the reassociate
bit before calling wpa_supplicant_connect(). wpa_supplicant connect
eventually aborts ongoing scans (if any), which causes scan results to
be reported. Since the reassociate bit is set, this will trigger a
connection attempt based on the aborted scan's scan results and cancel
the initial connetion request. This often causes wpa_supplicant to
reassociate to the same AP it is currently associated to instead of the
explicitly requested roaming target.
Add a roam_in_progress flag to indicate that we're currently attempting
to roam via an explicitly request to a specific BSS so that we don't
initiate another connection attempt based on the possibly received scan
results from a scan that was in progress at the time the roam command
was received.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Rename the network profile parameters bssid_blacklist and
bssid_whitelist to bssid_ignore and bssid_accept to use more specific
names for the configuration of which BSSs are ignored/accepted during
BSS selection. The old parameter names are maintained as aliases for the
new names to avoid breaking compatibility with previously used
configurations.
Signed-off-by: Jouni Malinen <j@w1.fi>
The wpa_bss structure's last element is an empty array. The forgotten
code here assumed that the array of IEs was contiguous to the wpa_bss
structure. This is not always the case anymore. Update this missed case
to use the new wpa_bss_ie_ptr() wrapper to send the correct array of IEs
over DBus.
Fixes: be7ee264f6 ("BSS: Use wrapper function for getting a pointer to the IE buffer")
Signed-off-by: Brad Kemp <brad at beechwoods.com>
Export a new 'suiteb192' capability to indicate that wpa_supplicant was
built with WPA-EAP-SUITE-B-192 support and accepts
'key_mgmt=WPA-EAP-SUITE-B-192'.
Signed-off-by: Antonio Cardace <acardace@redhat.com>
Report failures at lower layer to the upper layer D-Bus handling of
socket registration to allow failures to be addressed more cleanly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The D-Bus implementation of RemoveAllNetworks differs wildly from the
CLI implementation. Let's share the implementations.
This resolves use-after-free bugs I noticed, where we continue to use
the 'wpa_s->current_ssid' wpa_ssid object after freeing it, because we
didn't bother to disconnect from (and set to NULL) current_ssid before
freeing it.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Add D-Bus interface for ROAM command, imitating the existing wpa_cli
command.
Chromium OS has been carrying a form of this patch for a very long time.
I've cleaned it up a bit and documented it.
Signed-off-by: Brian Norris <briannorris@chromium.org>
This is needed for clearing previously set parameters in a similar
manner that was already available through the control interface
SET_NETWORK command.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Teach wpa_supplicant to {de,}initialize bgscans when bgscan parameters
are set after initial connection.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Currently, wpa_config_set(), the function that sets wpa_supplicant
per-network properties, returns 1 when a property it attempts to set is
unchanged. Its global parallel, wpa_config_process_global(), doesn't do
this even though much of the code is very similar. Change this, and
several of the parser functions, to resemble the per-network parser and
setter functions.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
When network properties are updated via dbus, wpa_config_set() is used
to update the property in the wpa_ssid struct. If it returns 1, the
property was not changed and there's no need to perform any of the
update actions.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
D-Bus clients can call CreateInterface() once and use the resulting
Interface object to connect multiple times to different networks.
However, if the network interface gets added to a bridge, clients
currently have to remove the Interface object and create a new one.
Improve this by supporting the change of the BridgeIfname property of
an existing Interface object.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
ignore_broadcast_ssid is supported when using with the config
file. But it generates an error if you try to set it via the
DBus interface.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
It was apparently possible to hit the 20000 octet limit in some cases,
so increase the limit to avoid process termination due to insufficient
room for preparing a response to Introspect calls.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a build flag CONFIG_NO_TKIP=y to remove all TKIP functionality from
hostapd and wpa_supplicant builds. This disables use of TKIP as both the
pairwise and group cipher. The end result does not interoperate with a
WPA(v1)-only device or WPA+WPA2 mixed modes.
Signed-off-by: Disha Das <dishad@codeaurora.org>
Support Extended Key ID in wpa_supplicant according to
IEEE Std 802.11-2016 for infrastructure (AP) associations.
Extended Key ID allows to rekey pairwise keys without the otherwise
unavoidable MPDU losses on a busy link. The standard is fully backward
compatible, allowing STAs to also connect to APs not supporting it.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
These are theoretical cases with 32-bit integers, but cases that could
potentially hit an integer overflow with 16-bit int.
Signed-off-by: Jouni Malinen <j@w1.fi>
This will be present when the driver supports SAE and it's included in
the wpa_supplicant build.
Signed-off-by: Brian Norris <briannorris@chromium.org>
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
This array had not been updated for years (since it was initially added)
and it was missing new network profile parameters that were not quoted
strings (but also not integers that could be set as integer types). Add
those missing non-quoted-strings to allow them to be set through the
DBus interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
These parameters are global parameters, not network profile parameters,
and as such, do not below in dont_quote[] which is used to determine
whether a network profile parameter needs to be quoted.
Signed-off-by: Jouni Malinen <j@w1.fi>
These properties were in the wpas_dbus_bss_properties array when they
should have been in the wpas_dbus_interface_properties array. Move them
to the right place. This is the logical location for these properties
and it matches both the other parts of the implementation (e.g., being
in enum wpas_dbus_prop, not in enum wpas_dbus_bss_prop) and what
was originally documented for the interface in dbus.doxygen.
Fixes: 2bbad1c7c9 ("dbus: Export roam time, roam complete, and session length")
Fixes: 80d06d0ca9 ("dbus: Export BSS Transition Management status")
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
This allows a P2P connection over P802.11ay EDMG channels to achieve the
highest link speed that the standard allows for channel bonding (CB) up
to CB4.
Let each P2P peer add its EDMG channels to the Supported Channels IE
advertised in P2P GO negotiation. Give EDMG channels priority when peers
negotiate for operating channel.
User may add 'edmg' parameter to p2p_connect, p2p_add_group, and
p2p_invite commands to prefer an EDMG channel for the P2P link. User may
also set p2p_go_edmg=1 in wpa_supplicant configuration file to prefer
EDMG.
When EDMG is used, P2P will try to find the highest channel bonding
supported channel that matches the frequency parameter, if the devices
do not support EDMG, the P2P connection will use a legacy (1-6) 60 GHz
channel.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Add D-Bus property:
* MACAddressRandomizationMask: a{say}
which configure random MAC address functionality in the Wi-Fi
driver via netlink.
Signed-off-by: Eric Caruso <ejcaruso@chromium.org>
Export a new 'owe' capability to indicate that wpa_supplicant was
built with OWE support and accepts 'key_mgmt=OWE'. Also, support 'owe'
in the array of BSS' available key managements.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
When the P2P management interface is deleted, P2P is then disabled and
global->p2p_init_wpa_s is set to NULL. After that, other interfaces can
still trigger P2P functions (like wpas_p2p_find()) using D-Bus. This
makes wpa_supplicant terminate with SIGSEGV, because it dereferences a
NULL pointer. Fix this by adding proper checks, like it's done with
wpa_cli.
CC: Beniamino Galvani <bgalvani@redhat.com>
CC: Benjamin Berg <benjamin@sipsolutions.net>
Reported-by: Vladimir Benes <vbenes@redhat.com>
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
wpa_s->dbus_groupobj_path is always NULL so suppress to show it.
This was found by gcc 9.2.1 warning.
dbus/dbus_new.c: In function ‘wpas_dbus_unregister_p2p_group’:
dbus/dbus_new.c:4793:3: warning: ‘%s’ directive argument is null [-Wformat-overflow=]
4793 | wpa_printf(MSG_DEBUG,
| ^~~~~~~~~~~~~~~~~~~~~
4794 | "%s: Group object '%s' already unregistered",
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
4795 | __func__, wpa_s->dbus_groupobj_path);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Hardcode this to be defined and remove the separate build options for
PMF since this functionality is needed with large number of newer
protocol extensions and is also something that should be enabled in all
WPA2/WPA3 networks.
Signed-off-by: Jouni Malinen <j@w1.fi>
We intentionally don't emit property-changed signals on every property
update -- for "less timing critical" messages we delay up to 5
milliseconds waiting to see if we can batch them together. When the
timer hits, we emit the signal anyway and (potentially) log this
message. This amounts to effectively tracing every property update,
which can be quite excessive.
Lower this to MSGDUMP, so MSG_DEBUG can remain slightly more sane.
Signed-off-by: Brian Norris <briannorris@chromium.org>
wpa_dbus_dict_close_write() was not called if
fill_dict_with_properties() fails and that could result in leaking
memory. Fix this in two cases. There might be other missing calls to
jouni@codeaurora.org() on error paths, but those will need to be handled
separately with more complex changes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This drops support for the fi.epitest.hostap.WPASupplicant D-Bus name
along with the associated CONFIG_CTRL_IFACE_DBUS option. Nothing should
really be using this since 2010.
This is a just a straightforward removal. Perhaps the dbus_common.c and
dbus_new.c can be merged now. Also, the "_NEW" suffix of the config
option seems to make even less sense than it used to.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
The Wi-Fi Alliance Multi-AP Specification v1.0 allows onboarding of a
backhaul STA through WPS. To enable this, the backhaul STA needs to add
a Multi-AP IE to the WFA vendor extension element in the WSC M1 message
that indicates it supports the Multi-AP backhaul STA role. The Registrar
(if it support Multi-AP onboarding) will respond to that with a WSC M8
message that also contains the Multi-AP IE, and that contains the
credentials for the backhaul SSID (which may be different from the SSID
on which WPS is performed).
Introduce a new parameter to wpas_wps_start_pbc() and allow it to be
set via control interface's new multi_ap=1 parameter of WPS_PBC call.
multi_ap_backhaul_sta is set to 1 in the automatically created SSID.
Thus, if the AP does not support Multi-AP, association will fail and
WPS will be terminated.
Only wps_pbc is supported.
This commit adds the multi_ap argument only to the control socket
interface, not to the D-Bus interface.
Since WPS associates with the fronthaul BSS instead of the backhaul BSS,
we should not drop association if the AP announces fronthaul-only BSS.
Still, we should only do that in the specific case of WPS. Therefore,
add a check to multi_ap_process_assoc_resp() to allow association with a
fronthaul-only BSS if and only if key_mgmt contains WPS.
Signed-off-by: Davina Lu <ylu@quantenna.com>
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Cc: Marianna Carrera <marianna.carrera.so@quantenna.com>
The previous implementation assumed the first entry coming out from the
dict is always service_type. That may not be the case, so properly
iterate over all dict entries in one loop instead of assuming what the
first entry is.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is probably not ideal, since it would be better if it ended up
being autogenerated somehow, but at least it's somewhat of an
improvement.
Also added a comment that encourages keeping the docs in sync.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
If we call p2p_flush from ctrl_iface, before calling p2p_flush() it
calls wpas_p2p_stop_find(). Add the same call to the matching D-Bus
method to clear all pending operations.
Signed-off-by: Amit Khatri <amit7861234@gmail.com>
An optional parameter "he" is added to p2p_connect, p2p_group_add, and
p2p_invite to enable 11ax HE support. The new p2p_go_he=1 configuration
parameter can be used to request this to be enabled by default.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wpa_s->bss_tm_status is within #ifdef CONFIG_WNM, so need to access it
through matching condition.
Fixes: 80d06d0ca9 ("dbus: Export BSS Transition Management status")
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_supplicant currently logs CTRL-EVENT-AUTH-FAILED errors when
authentication fails, but doesn't expose any property to the D-Bus
interface related to this.
This change adds the "AuthStatusCode" property to the interface, which
contains the IEEE 802.11 status code of the last authentication.
Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
Add new Interface properties "BSSTMStatus", which carries the status of
the most recent BSS Transition Management request. This property will be
logged in UMA to measure 802.11v success.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
