IEEE 802.11be enables multiple links between STA and AP. Each of the
link has its own set of statistics. Add additional attributes required
to fetch link layer statistics per MLO link.
For MLO connection, per MLO link statistics will be sent with the new
attribute QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. Also, cumulative
statistics of all the MLO links will be sent outside
QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK to be compatible with legacy user
space.
For non-MLO connection, the statistics will be sent without being nested
inside QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK attribute.
Co-authored-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
The attributes QCA_WLAN_VENDOR_ATTR_LL_STATS_PAD and
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NF_CAL_VAL were allocated the same
attribute number in error. QCA_WLAN_VENDOR_ATTR_LL_STATS_PAD attribute
is known to not be used; thus, it is safe to be renumbered.
Fixes: 1491fc64a8 ("Define QCA vendor per-enum 64-bit pad attributes")
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
When user space triggers a scan, the firmware aborts background scan,
and uses the roam status QCA_ROAM_FAIL_REASON_CURR_AP_STILL_OK instead
of "Invalid roam failures reason".
Signed-off-by: Chunquan Luo <quic_chunquan@quicinc.com>
Define bitmap values used by LL_STATS vendor command
and update the corresponding kernel documentation.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Print correct expected AP MLD address information when the AP MLD
address validation fails in Authentication frames during external
authentication.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Fail MLD address validation only if Authentication frames IE parsing
actually failed, i.e., ignore all unknown IEs.
This is needed to avoid authentication failure when the Authentication
frames include IEs which are not handled by ieee802_11_parse_elems(),
e.g., AKM Suite Selector IE.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
hostapd start AP flow changed in commit 931e5d4f9e. However, that
could cause a regression in a legacy AP driver where the set key
operation for GTK, IGTK, and BIGTK before AP start (set beacon) would
cause the driver to ignore the key set command. Restore the flow of the
set beacon and WPA key init operations to make sure drivers can receive
and set group keys correctly.
Fixes: 931e5d4f9e ("mbssid: Configure all BSSes before beacon setup")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Export the "he" network profile item to be configurable from external
client side, like wpa_cli or NetworkManager. This follows the earlier
changes to allow the previously internal-only parameter (e.g., vht) to
be used for additional purposes for AP mode.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Add support to configure the allowed frequency list for AP operation
using a QCA vendor interface before NL80211_CMD_NEW_BEACON/
NL80211_CMD_START_AP. hostapd generates the allowed frequency list by
intersecting user configured frequency list and all the frequencies
advertised by the driver including disabled channels. If user doesn't
specify allowed frequency list, all the frequencies advertised by the
driver, including disabled channels, will be configured.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
At least some of the previous versions have expired, so need to re-sign
these to avoid EAP test case failures. This contains updates from
running tests/hwsim/auth_server/update.sh.
Signed-off-by: Jouni Malinen <j@w1.fi>
In theory, each device that supports WMM (or the IEEE 802.11 QoS for
that matter) is expected to advertise how many replay counters it
supports and the peer device is supposed to use that information to
restrict the total number of different MSDU priorities (AC/UP) that
might be used. In practice, this is not really done in deployed devices
and instead, it is just assumed that everyone supports the eight
different replay counters so that there is no need to restrict which
MSDU priorities can be used.
hostapd implementation of WMM has advertised support for 16 PTKSA replay
counters from the beginning while wpa_supplicant has not had any code
for setting the supported replay counter fields in RSNE, i.e., has left
the value to 0 which implies that only a single replay counter is
supported. While this does not really result in any real issues with
deployed devices, this is not really correct behavior based on the
current IEEE 802.11 standard and the WMM specification.
Update wpa_supplicant to use similar design to the hostapd RSNE
generation by setting the number of supported PTKSA replay counters to
16 whenever WMM is enabled. For now, this is done based on the
association being for HT/VHT/HE/EHT and also based on the AP supporting
WMM since it is much more likely for the local device to support WMM and
eight replay counters (which can be indicated only with the value that
implies support for 16 counters since there is no separate value for 8).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add new nested netlink attribute, NL80211_ATTR_EMA_RNR_ELEMS, to send
the reduced neighbor report (RNR) elements to the driver when EMA is
enabled. This attribute includes the count of RNR elements and data at
each index. While generating EMA beacons, the driver will include RNR
group at a given index along with MBSSID group. The last element, if
present, has RNR data common for all EMA beacons such as neighbor APs.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
As per IEEE Std 802.11ax-2021, 11.1.3.8.3 Discovery of
a nontransmitted BSSID profile, an EMA AP that transmits a Beacon
frame carrying a partial list of nontransmitted BSSID profiles
should include in the frame a Reduced Neighbor Report element
carrying information for at least the nontransmitted BSSIDs that
are not present in the Multiple BSSID element carried in that frame.
Add this support by splitting the reduced neighbor report (RNR) in as
many elements as the number of multiple BSSID elements. Each RNR element
excludes the non-transmitting profiles already included in the MBSSID
element at the same index. If present, the last additional group will
have the data common for all EMA beacons such as neighbor AP information
gathered through neighbor reports.
The hwsim test case he_ap_ema demonstrates this support.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Do not include interfaces on the same radio in reduced neighbor
report elements (RNR) as multiple BSSID elements from the same
management frame already include these if MBSSID feature is enabled.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Add a vendor feature flag for the driver to indicate support for allowed
frequency configuration in AP mode.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add a new vendor command to trigger computation of connected channel
statistics such as channel utilization in STA mode.
Signed-off-by: Ainy Kumari <quic_ainykuma@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Define a new attribute QCA_WLAN_VENDOR_ATTR_CONFIG_AP_ALLOWED_FREQ_LIST
to configure the full list of allowed frequencies for the AP operation.
The configuration is valid only from the next BSS start until the BSS is
stopped. The drivers shall filter out channels on top of this list of
channels based on regulatory or other constraints. This can be used to
specify user's choice of frequencies, allowed list of channels with
static puncturing feature, etc.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add the channels 165 and 173 in allowed channels for ht40_plus. Also add
the allowed frequency 5825 (channel 165; channel center frequency index
171) for 80 MHz bandwidth.
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
center_idx_to_bw_6ghz() does not return the bandwidth in MHz and as
such, the check here against 20 (MHz) is never true. The returned value
is greater than 0 for the over 20 MHz cases.
Fixes: 15742566fd ("6 GHz: Fix operating class in Supported Operating Classes element")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The following command does not return FAIL, but it fails to update the
beacon since the center frequency used in the command is not valid for
80 MHz bandwidth.
hostapd_cli -i wlan0 chan_switch 5 6315 sec_channel_offset=1 \
center_freq1=6345 bandwidth=80 he
Add condition check to validate the center frequency.
Also, if user doesn't provide HE parameter in the hostapd_cli
chan_switch command, by default HE should be enabled for 6 GHz
frequency range. This is because, 6 GHz does not support legacy
mode.
Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Co-developed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
The STATUS command showed the interface state as SCANNING even if mesh
bringup fails. This incorrect interface status can mislead
scripts/applications that rely on interface status to bring up different
type of virtual interfaces (AP/MESH) on a single radio.
Fix this by setting the interface status as INACTIVE if mesh bringup
fails.
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
hostapd_cli did not clean up the sockets and attachments to receive
hostapd events when SIGTERM was used to terminate it in action script
mode.
Do proper cleanup by convering the action script processing
functionality to use eloop similarly to the wpa_cli changes in commit
13f6f617ee ("wpa_cli: Fix process termination in wpa_cli action mode
case") and by registering the process termination signal handler for all
cases instead of just for the interactive mode.
Signed-off-by: Sai Pratyusha Magam <quic_smagam@quicinc.com>
Find a STA entry based on MLO affiliated link addresses for the case
where an unprotected Data frame is being processed. This extends the
changes in commit 228420e2d9 ("wlantest: Find a STA entry based on MLO
affiliated link addresses") to cover the unencrypted case. This is
needed in particular for the Null frames used for managing the power
save state to avoid generating duplicate STA entries that can mess up
key information for the following frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
These are needed to allow the Suite B 192-bit negotiation to succeed
when using TLS 1.3 (which is still disabled by default).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_WIDTH to configure 320 MHz
bandwidth to the driver/firmware.
Signed-off-by: Ainy Kumari <quic_ainykuma@quicinc.com>
Add a new option 'punct_acs_threshold' where the value indicates
the percentage of ideal channel average interference factor above
which a channel should be punctured. Default is set to 0 which disables
the puncturing for ACS.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Retrieve the puncturing bitmap sent by the driver in channel switch
events and add a new member punct_bitmap in struct ch_switch to store
it.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Send the user configured puncturing bitmap to the driver.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Add preamble puncturing bitmap to the EHT Operation element as per IEEE
P802.11be/D3.0, Figure 9-1002c (EHT Operation Information field format).
Bits set to 1 indicate that the subchannel is punctured, otherwise
active.
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Legacy modes (VHT, HE) should advertise downgraded bandwidth if
RU puncturing is enabled in EHT mode. This is required for the legacy
stations which cannot parse the EHT Operation elements hence do not
support EHT RU puncturing.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Ramanathan Choodamani <quic_rchoodam@quicinc.com>
Add a new option to configure the disabled subchannel bitmap as per
IEEE P802.11be/D3.0, Figure 9-1002c (EHT Operation Information
field format).
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Retrieve the driver support for preamble puncturing.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Maximum NSS calculation assumed the host to be little endian while
retrieving MCS values from HE capabilities which is incorrect. Use
WPA_GET_LE16() instead.
Add a check for HE as the current NSS calculation assumes HE support.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
FILS discovery frame generation currently assumes HE support for
calculating the number of spatial streams. Add a check to reject
the configuration if the feature is enabled without enabling HE.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Once ACS picks a channel, iface->freq and iface->conf->channel are
updated. So, AP comes up in the last operating channel when 'ENABLED'
after 'DISABLED' though ACS is configured.
But this will fail for 6 GHz APs since configured_fixed_chan_to_freq()
checks if iface->conf->channel is filled or not irrespective of ACS
configuration, and the checks inside configured_fixed_chan_to_freq()
fail the AP setup. Fix this by clearing iface->freq and
iface->conf->channel in AP setup for ACS configuration.
Fixes: bb781c763f ("AP: Populate iface->freq before starting AP")
Signed-off-by: Pooventhiran G <quic_pooventh@quicinc.com>
If wiphy idx not provided, kernel returns global reg domain when
processing NL80211_CMD_GET_REG. To obtain the correct country code for
the self-managed regulatory cases, put wiphy idx into nl_msg when
sending this command to kernel.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When writing 64-bit attributes into the netlink buffer, senders may
add a padding attribute to allow the payload of the 64-bit attribute
to be 64-bit aligned. For QCA vendor attributes, currently the
attribute QCA_WLAN_VENDOR_ATTR_PAD in enum qca_wlan_vendor_attr is
defined for this purpose.
Unfortunately, when adding attributes to the netlink buffer, all
attributes at a given level of nesting must be defined in the same
enum so that they can be unambiguously parsed. This means that
QCA_WLAN_VENDOR_ATTR_PAD can only be used to pad 64-bit attributes
defined in enum qca_wlan_vendor_attr.
There are many other QCA vendor enums which define 64-bit attributes,
so add a pad attribute to all of them so that the 64-bit attributes
can be unambiguously padded.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Add a new vendor command and attributes to control and fetch the state
information of the MLO links affiliated with a specific interface.
This will enable user space to dynamically control the MLO links states
based on the latency, throughput and power save requirements.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Add mesh_eht_enabled and eht ssid configuration parameters to include
EHT Capability and EHT Operation elements in mesh PLINK Action frames.
Update mesh_eht_enabled from EHT capability advertised for mesh mode.
Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
This is needed to derive the PTK correct when Secure LTF support is used
and the additional KDK component needs to be taken into account.
Signed-off-by: Adil Saeed Musthafa <quic_adilm@quicinc.com>
