Only run-tests.py is actually executed, so there is no need to specify
the interpreter in all the helper files and test script files.
Signed-off-by: Jouni Malinen <j@w1.fi>
CONFIG_MODULE_TESTS=y build option can now be used to build in module
tests into hostapd and wpa_supplicant binaries. These test cases will be
used to get better testing coverage for various details that are
difficult to test otherwise through the control interface control. A
single control interface command is used to executed these tests within
the hwsim test framework. This commit adds just the new mechanism, but no
module tests are yet integrated into this mechanism.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify cases both with multiple peers (one of which not advertising any
services) and with multiple SD queries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like some of the discovery_* test cases have been failing every
now and then on the virtual server and the one second timeout could have
been a bit too short to cover some possible timing cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Enable hostapd control interface for the RADIUS server instance and
verify that the RADIUS server MIB counters are incremented.
Signed-off-by: Jouni Malinen <j@w1.fi>
This improves accuracy of the code coverage reports with hostapd-as-AS
and hlr_auc_gw getting analyzed separately.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a password that uses one, two, and three octet encoding
for UTF-8 characters. The value is tested against a pre-configured
hash to verify that utf8_to_ucs2() function works correctly.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like get_status() has failed in some test runs because of a
STATUS command returning an line without '=' on it. Instead of stopping
there on exception, report the unexpected line in the log and ignore it
to allow test to continue.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that NFC connection handover can be used in a case where
hostapd has an enabled password token.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that PD Request followed by GO Negotiation Request is enough to
learn the Listen frequency of the peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
To test the code under the influence of time jumps, add the option
(--timewarp) to the VM tests to reset the clock all the time, which
makes the wall clock time jump speed up 20x, causing gettimeofday()
to be unreliable for timeout calculations.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Since wlantest is a separate process that is not synchronized with rest
of the test components, there can be some latency in it having the STA
entries and counters updated. There is a race condition between this
happening and then test script clearing or fetching data. Make this race
condition less likely to cause bogus test failures by adding some wait
between these operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
In addition to running the FLUSH command again, the pending monitor
interface events need be cleared in case the driver was running a scan
when reset() is called. This avoids issues, e.g., with discovery_dev_id
failing due to an unexpected P2P-DEVICE-FOUND event that was generated
by the pending scan operation that had not yet complete when the first
dump_monitor() call in reset() happened.
Signed-hostap: Jouni Malinen <j@w1.fi>
The vm-config in the subdirectory is less useful as it
will get removed by "git clean" and similar, so read a
config file from ~/.wpas-vm-config in addition.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It looks like slow virtual machines may have issues to complete some EAP
authentication cases (e.g., EAP-EKE in ap_ft_eap) within the 10 second
timeout under load. Double the timeout to avoid incorrect test failures.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the previous test case to leave unexpected BSS or
P2P peer table entries if a scan was in progress when the FLUSH command
was used. This could result in test failures, e.g., when running
discovery_dev_type_go followed by discovery_group_client where a P2P
peer was discovered on another channel at the end of the former test
case from a scan that was running durign the FLUSH operation that was
supposed to remove all P2P peers. This could result in
discovery_group_client failing due to dev[2] trying to send the
discoverability frame on incorrect channel (the one learned in the
previous test case) since discover_peer() skipped a new device
discovery. Fix this by running FLUSH operation again if a pending scan
operation is detected during the first FLUSH operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In addition, add the earlier tests in the new test_ssid.py file that was
forgotten from the previous commit
d78f33030d.
Signed-hostap: Jouni Malinen <j@w1.fi>
WPS-ER-AP-REMOVE event from the ER is sent before HTTP UNSUBSCRIBE has
been completed. As such, it was possible for the following scan
validation step to be started before the AP has had a chance to react to
the ER status change. Makes this less likely to fail by waiting 200 ms
before starting the last scan.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was possible for the AP to report two enrollees in this test case
(i.e., both the expected wlan1 device and also the ER device on wlan0).
The previous test script would fail if the wlan0 device is reported
first. Fix this by allowed the expected target to be found in either the
first or the second WPS-ER-ENROLLEE-ADD event.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was possible for this test case to fail if P2P_FLUSH was issued
during a search scan and that scan adding back the peer. Avoid this by
forcing p2p_find to be started regardless of the current P2P peer table
contents for each round of service discovery.
Signed-hostap: Jouni Malinen <j@w1.fi>
With the extra latencies removed from run-tests.py operations, it was
possible to hit race conditions in pairwise cipher configuration at the
end of the 4-way handshake. In some cases, the EAPOL-Start frame from
the station was not received by the AP and that could result in these
test cases failing. Since there are not really trying to test the race
condition, wait for the AP side to complete key configuration prior to
initiating the reauthentication sequence.
Signed-hostap: Jouni Malinen <j@w1.fi>
When a thread is used to follow P2P group formation progress, it is
better to return a clear failure indication from the thread instead of
allowing an exception to be thrown from the thread.
Signed-hostap: Jouni Malinen <j@w1.fi>
Leave couple of cases to use full scan for better test coverage, but
change all other places to use a single channel scan with
INTERWORKING_SELECT to reduce the time it takes to execute the tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is possible that wlantest has not yet created the BSS entry in all
cases, so interpret failures (no BSS entry being the most likely cause)
as zero counters. Similarly, ignore clear_bss_counters errors since they
are most likely reporting that the BSS was not found and as such, there
was no need to clear the counters anyway.
Signed-hostap: Jouni Malinen <j@w1.fi>
The FLUSH command clears disallow_aps, p2p_disabled, and
p2p_per_sta_psk, so there is no need to clear them separately.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace the fixed 100 ms waits with a select()-based wait and timeout
for full wait based on monotonic time to optimize wait_event().
Signed-hostap: Jouni Malinen <j@w1.fi>
Do not run a full scan in gas_generic since this is not really needed.
Dump pending event messages after long wait to make logs clearer.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it easier to build a web page for analyzing failures without
having to fetch the log files themselves from the test server.
Signed-hostap: Jouni Malinen <j@w1.fi>
No need to run a full scan as the first step since it only needs to find
the AP from a known channel for the GAS operation.
Signed-hostap: Jouni Malinen <j@w1.fi>
Now that wpa_supplicant requests the driver (cfg80211) to clear its scan
cache automatically after each BSS_FLUSH/FLUSH command, the previously
used ignore_old_scan_res workaround should not be needed for the hwsim
test cases anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
