The STA can get disconnected event before the AP processed the
deauthentication frame, resulting in GET_FAIL command being sent too
early. Fix this by waiting for AP-STA-DISCONNECTED on AP side, too.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Import vht_supported from test_ap_vht to fix the following issue:
rrm_beacon_req_table_vht run failed: global name 'vht_supported' is not defined
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
ubsan reported:
../src/crypto/random.c:69:30: runtime error: shift exponent 32 is too large for 32-bit type 'unsigned int'
Explicitly check for the ROL32(x, 0) case which is supposed to be a
no-op.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
After KDF negotiation, must check only requested change occurred in the
list of AT_KDF attributes. If there are any other changes, the peer must
behave like the case that AT_MAC had been incorrect and authentication
is failed. These are defined in EAP-AKA' specification RFC 5448, Section
3.2.
Add a complete check of AT_KDF attributes and send Client-Error if a
change which is not requested is included in it.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sony.com>
AT_KDF attributes need to be included in Synchronization-Failure
according to EAP-AKA' specification RFC 5448.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sony.com>
pmksa_cache_add_entry() may actually free old_entry if the PMKSA cache
is full. This can result in the PMKSA cache containing entries with
corrupt expiration times.
Signed-off-by: Andrew Elble <aweits@rit.edu>
This introduces a new interface for mesh and adds a signal that
is similar to the control interface event MESH-GROUP-STARTED.
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
The "FILS: No pending HLP DHCP exchange with hw_addr" debug message was
missing a space before the following MAC address, so add that there to
make the message more readable.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like these parameters related to FT have never been used, so
remove them from causing confusion. The separate update_ft_ies()
callback is used to provide the FT elements.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to post-process frame capture files if frames need
to be decrypted in test cases that do not configure wlantest with the
PMK directly (i.e., mainly the cases when a RADIUS server is used).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Try to derive PTK when FILS shared key authentication is used without
PFS. The list of available PMKs is interpreted as rMSK for this purpose
and PMK and PTK is derived from that. If the resulting PTK (KEK) can be
used to decrypt the encrypted parts of (Re)Association Request/Response
frames, mark the PTK as derived so that encrypted frames during the
association can be decrypted. In addition, write a decrypted version of
the (Re)Association Request/Response frames into the output file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new "SET sae_commit_override <hexdump>" control interface command
can be used to force wpa_supplicant to override SAE commit message
fields for testing purposes. This is included only in
CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new sae_commit_override=<hexdump> parameter can be used to force
hostapd to override SAE commit message fields for testing purposes. This
is included only in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow hostapd to be configured to perform SAE reflection attack for SAE
testing purposes with sae_reflection_attack=1 configuration parameter.
This is included only in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add PMKID into EAPOL-Key 1/4 when using SAE and fix the PMK-from-PMKSA
selection in some cases where PSK (from passphrase) could have been
used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was previously defined inconsistently (H() vs. SHA256()), but it is
now clarified in the draft tech spec to use SHA256(), so update
implementation to do that.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
NL80211_ATTR_AUTH_TYPE needs to be skipped if multiple auth_alg options
are included. The previous list missed the new FILS auth_alg here and
ended up not doing so if OPEN and FILS were included.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Wait for the configuration step to complete before forcefully
terminating DPP listen. Previous version was causing failures for this
test case sequence:
dpp_qr_code_auth_initiator_enrollee dpp_pkex_config2
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
DPP tech spec changed the contents of these frames by replacing the
public key hash attributes with a Transaction ID attribute that gets
copied from the request to the response to identify the transaction in a
simpler manner.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use the SSL_get_SSL_CTX() helper instead of dereferencing SSL* since
struct ssl_st is not exposed in public header files anymore.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is an event indicating to the user space that the driver has
detected an internal failure. The driver is expected to recover from
such a failure automatically, e.g., by resetting the device. This event
carries the information indicating the reason that triggered this
detection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previous implementation was able to parse arrays of objects, but not
arrays of other types of items.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
