Always set SNonce cookie and enable RSN Override elements validation
irrespective of the RSN Selection element usage in (Re)Association
Request frame when RSN overriding supported.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
STA needs to skip validating RSN Override elements when RSN overriding
is not used since AP will not send RSN Override elements in EAPOL-Key
message 3/4. This is handled correctly in non-MLO case but in MLO case
wpa_supplicant always validates RSN Override link KDEs. Fix validating
RSN Override elements in MLO case as well.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
A STA that supports RSN overriding will always use the SNonce cookie. An
AP that does not advertise RSN overriding elements must not enforce that
SNonce cookie is used with RSN Selection element since a STA includes
the latter only when it sees the AP advertising RSN overriding elements.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Modify wpa_supplicant code based on the updated driver interface for RSN
overriding capability indication.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Be more specific on how the QCA_WLAN_VENDOR_ATTR_FEATURE_FLAGS attribute
is used in the response.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add QCA_NL80211_VENDOR_SUBCMD_CONNECT_EXT to send additional information
such as RSN overriding support of the supplicant for the (re)association
attempts with NL80211_CMD_CONNECT.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Use separate interfaces for indicating driver and supplicant RSN
overriding support. Modifying this interface is fine since this feature
is still under development.
Subsequent commit will define the interface for indicating supplicant
RSN overriding support to the driver.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
wpa_auth_get_seqnum() for ML group rekeying needs to be skipped in the
same way as it is done for non-ML cases to avoid indicating old values
and resulting in group frames being dropped as replays. The simple check
for gsm->wpa_group_state != WPA_GROUP_SETKEYS (as is done for non-ML) is
not sufficient for this since the per-link Authenticator states are not
strictly synchronized and the state change happens in the middle of this
step.
Fixes: 137b855092 ("MLO: Mechanism for fetching group key information for the links")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
At present, group key update is not confined only on the association
link as originally intended. Hence, ensure now that the group key update
is only performed on the association link for non-AP MLDs.
This was missed during adding support for group rekeying for MLO.
Fixes: 12acda633b ("AP MLD: Support group rekeying for MLO")
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
The AP MLD change to use a helper function for this broke the design
that depends on the value for sm->group (i.e., the currently assigned
VLAN) being used instead of the sm->wpa_auth->group. Restore previous
behavior to fix GKeyDoneStations tracking when VLANs are used.
Fixes: 78adbf2c08 ("AP MLD: Mark GKeyDone completed for STAs in a helper function")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The new test case for an AP MLD in a bridge was supposed to use a unique
test name to avoid hiding an existing test case.
Fixes: c4f9279267 ("tests: AP MLD with two links in a bridge")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
In the current hostapd flow, AP_VLAN net device is added to a bridge
before the interface is brought up.
Interface up event is used in mac80211 layer for setting device context
in the driver. Vendor specific datapath offload configurations for net
device might also be set up in interface up event context. Adding
AP_VLAN interface to a bridge before the UP event could cause
inconsistent state for datapath offload context setup in a vendor
driver.
Change the sequence to add AP_VLAN interface to a bridge after the
interface is set up. This makes the interface up and bridge add sequence
for AP_VLAN to be consistent with that of a regular AP interface.
Signed-off-by: Radha Krishna Simha Jiguru <quic_rjiguru@quicinc.com>
During FT, RRB messages are getting dropped at bridge on an AP MLD since
bridge doesn't know all the link address, so roaming gets failed.
Add AP MLD's each link address to the bridge FDB, so that RRB frames
get forwarded through bridge to hostapd.
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
bss->flink could be NULL when wpa_driver_nl80211_del_beacon() is called
if wpa_driver_nl80211_drv_init() fails early through the 'failed' label
and jumps to wpa_driver_nl80211_deinit() with bss->flink unset.
Fixes: 47269be36e ("nl80211: Refactor i802_bss to support multiple links")
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
Currently, channel is selected from the current hw_mode. However, not
all channels under current hw_mode might be available for the current
operating underlying hardware.
Add logic to check if the selected channel falls under the current
operating hardware index and only if so, continue with the selected
channel.
Co-developed-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
When a driver consolidates several hardware components under a single
radio, it provides details about these components via the
NL80211_CMD_GET_WIPHY command.
Parse this information and store it. A subsequent change will use this
information for validation in certain scenarios.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Whenever there is only one BSS left and if the number of links is one,
is_shared_drv() returns false assuming no one else is sharing the driver
interface. However, when the number of links is one, this does not
guarantee that the caller's link ID is the only active link ID. If this
is not the case and false is returned, the caller calls hapd_deinit()
which will free the driver interface. However, when the actual active
link_id reaches deinit path, this leads to dereferencing a NULL pointer
ultimately leading to segmentation fault.
To prevent this, pass the link ID into the is_drv_shared() ops and match
it with only with active link IDs. Only return false if they are same.
Signed-off-by: Ganesh Kariganuru Mahabalesh <quic_gkarigan@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
In function driver_nl80211_link_remove(), when there is no active links,
interface is removed. This will free the BSS pointer. A copy of the BSS
pointer is also stored in each of the affiliated links' hapd->drv_priv
member.
driver_nl80211_link_remove() is called via multiple paths, e.g., via
NL80211_CMD_STOP_AP and via driver_nl80211_ops. When called when
handling an nl80211 event, links will be removed and when count reaches
zero, the interface will be removed. However, core hostapd will be
unaware of this removal. Hence, if it tries to access its drv_priv
pointer, this can lead to segmentation fault at times since the pointer
is now pointing to freed memory.
Prevent this by adding a new notification event
(EVENT_MLD_INTERFACE_FREED). Whenever the interface is freed, this
notification will be sent. hostapd will process this notification and
will set all affliated links' hapd->drv_priv to NULL.
Signed-off-by: Naveen S <quic_naves@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Currently, a stop AP event is processed always on the first BSS in the
drv. However, with multi-link operation, it can come on any interface
and there is need to process it for the intended BSS. Also, the event
has a link ID attribute during MLO which is not used and still the event
is passed to the first link BSS.
Process the event for the intended BSS and for the intended link BSS
during MLO.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
No functionality changes.
This is needed to support STOP_AP events for MLD interface in a
subsequent change.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
When an interface is enabled, keys are reconfigured, if required, and
beaconing is started again. With MLO, this needs to be done for each of
the affiliated links. Before starting the beaconing, the link needs to
be added back first.
Similarly, when the interface is disabled, hostapd removes the keys and
set the BSS state to disabled. However, for an AP MLD interface, this
needs to be done for each of the affiliated link BSS.
Handle the interface enable/disable driver event for AP MLD.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Driver events for interface enable/disable are currently handled on
interface level with one hostapd_data instance under consideration. In
order to extend it for MLO, this needs to be done for each of the
affiliated links. Hence, refactor the code into a helper function which
can be used later.
No functionality change. Support for MLO will be added in a subsequent
change.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Store the full set of AP's RSNE/RSNXE variants to wpa_sm while
processing association event. Commit 521374b978 did this for the cases
that were needed for SME-in-wpa_supplicant cases, but forgot to update
the cases needed for SME-in-driver. Convert those to the updated
protocol design as well.
Fixes: 521374b978 ("RSNO: Include all RSNE/RSNXE variants in EAPOL-Key message 3/4")
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Some APs do not advertise operating classes correctly for BSS Transition
Management. Try to determine the most likely operating frequency based
on the channel number (1..14 --> 2.4 GHz; 36..177 --> 5 GHz) if invalid
op_class == 255 is received in a BSS Transition Management Request. This
speeds up the following operating by avoiding a full scan due to an
unknown channel.
This extends the workaround that was added in commit 80ce804e88 ("WNM:
Workaround for broken AP operating class behavior") for invalid
operating class 0 to cover another observed case with invalid operating
class 255.
Signed-off-by: Yu Zhang(Yuriy) <quic_yuzha@quicinc.com>
Currently MLO CSA test case supports CSA only on the first link.
However, now it can be extended to other links as well.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
During channel switch handling for AP MLD, if link ID is incorrect,
there is no point in proceeding till end and failing or returning from
there. Hence sanitize it in the initial time itself and return if it is
incorrect. Throw a warning print if it is not correct as well.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Channel switch operation fails if 'eht' option is given without 'he'
as hostapd_config_check() returns following error:
"Cannot set ieee80211be without ieee80211ax"
The issue is seen only when switching within/to DFS channels because
hostapd_switch_channel_fallback() does not set 'ieee80211ax' in
hostapd configuration unless 'he_enabled' is set for the new channel.
Set 'he_enabled' in struct hostapd_freq_params for channel switch
when EHT is enabled.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Now that per STA profile is cached already, there is no need to form it
dynamically on every Probe Request frame.
Use the cached one instead.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
As per IEEE P802.11be/D7.0, 35.3.3.5.1 (Inheritance in the Per-STA
Profile subelement of Basic Multi-Link element), Note 1, if there exists
one or more Vendor Specific elements carried in a Management frame that
includes the Basic Multi-Link element containing a per-STA profile for a
reported STA, and the contents of the Information field for at least one
of the Vendor Specific elements is not the same as that of at least one
Vendor Specific element that applies to the reported STA, then each
Vendor Specific element that applies to the reported STA is included in
its Per-STA Profile subelement.
Handle this.
Signed-off-by: Arunpandi Kannan <quic_arunpand@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
There can be an element in the reporting BSS which is not there in the
reported BSS. This element should not be inherited in the per STA
profile. Hence to indicate this, the corresponding per STA profile
should include a Non-Inheritance element in the per STA profile.
Include Non-Inheritance element in the per STA profiles when needed.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
If an element is present in the reporting BSS and it is also present in
the reported BSS and the contents are same, ideally, the reported BSS
need not carry such element in its per STA profile. Such elements are
assumed to be inherited from the reporting BSS.
Intersect the reported BSS profile with the reporting BSS and avoid such
element inclusion.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
There are certain elements which should not be included in a per STA
profile.
Ignore such elements.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Currently, upon receiving a Probe Request frame, per STA profile is
generated and added to the Probe Response frame. However, the per STA
profile remains unchanged unless there’s a property change in one of the
affliated link of the AP MLD. This approach introduces unnecessary delay
in forming and sending out the Probe Response frame.
To optimize this process, generate the per STA profile for each link at
the start and store it. When needed, it can be simply copied into the
Probe Response frame. Additionally, whenever there’s a change in the
link’s properties, re-generate the per STA profiles for all affiliated
links of the AP MLD.
As an initial step, copy the complete per STA profile and store it
within the links. The intersection with reporting BSS and inheritance
will be addressed in a subsequent change. Then finally, this will be
used to generate the Probe Response frame. As of this commit, no change
in adding per STA profiles in the Probe Response frame.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
At present, the mld_link_info structure is nested within the mld_info
structure. However, a future modification will require mld_link_info to
be outside of mld_info. To address this, move the mld_link_info
structure to hostapd.h so that it can be accessed both in the current
context and in the location needed for the upcoming change.
No functional changes.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Prior to initiating communication on a DFS channel, channel availability
check needs to be performed. During this period, the AP does not beacon.
Hence, no channel switch was allowed during this period. However, if a
user wishes to switch to a non-DFS channel during the potentially long
CAC period and start transmission immediately, there is no provision to
do that currently.
Extend the existing CHAN_SWITCH control interface command to allow
channel switch even when the AP is in CAC state. To do this, first
disable the interface to abort the CAC in progress and then configure
the interface with the new parameters and finally re-enable the
interface.
Signed-off-by: Amith A <quic_amitajit@quicinc.com>
In the send_assoc_resp() function, there’s a chance that the sta
argument could be NULL. Therefore, it’s crucial not to directly
dereference sta without first checking whether it’s a valid pointer.
However, commit 58ac46baf7 (“WNM: AP configuration to allow BSS max
idle period requests”) introduces direct dereferencing of max idle
period from sta, which might lead to a NULL pointer dereference. Fix
this now.
Fixes: 58ac46baf7 ("WNM: AP configuration to allow BSS max idle period requests")
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
The Bandwidth Indication subelement contains channel bandwidth, channel
center frequency, and optionally punctured subchannels.
As per IEEE P802.11be/D7.0, 35.15.3 (Channel switching methods for an
EHT BSS), if a Channel Switch Announcement element or an Extended
Channel Switch Announcement element is used to announce a switch to an
EHT BSS operating channel width wider than 160 MHz or to an EHT BSS
operating channel width including at least one punctured 20 MHz
subchannel, the Bandwidth Indication subelement in the Channel Switch
Wrapper element shall be present in the same frame.
Hence, add it into the Beacon and Probe Response frames under the above
mentioned conditions.
Signed-off-by: Karthik M <quic_karm@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
The Wide Bandwidth Channel Switch subelement was directly appended in
the Channel Switch Wrapper element function
hostapd_eid_wb_chsw_wrapper(). However, a subsequent change would add
Bandwidth Indication subelement in the Channel Switch Wrapper element.
Hence using the same function name would be confusing.
Hence, refactor the current code into two functions. The first function
hostapd_eid_chsw_wrapper() forms the channel switch wrapper element.
This calls hostapd_eid_wb_channel_switch() to add a Wide Bandwidth
Channel Switch subelement inside it.
No functionality change.
Signed-off-by: Karthik M <quic_karm@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
During MLO, an nl80211_cqm_event may be received by any BSS. Directing
this event to the first BSS may not be suitable as it might not
correspond to the link the event is meant for. Hence, there is a need to
handle this on per-BSS basis.
Therefore, handle nl80211_cqm_event per BSS. The event handler further
uses the address information present in the event to fetch the intended
link BSS if no matching STA entry was found based on the initial
ap_get_sta() call.
Signed-off-by: Manish Dharanenthiran <quic_mdharane@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
The hostapd_find_by_sta() function may be utilized by multiple driver
events. Therefore, it should be declared at the outset to ensure
accessibility by all event handlers.
No functional changes.
Signed-off-by: Manish Dharanenthiran <quic_mdharane@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
The Max Channel Switch Time element indicates the time delta between the
time the last beacon is transmitted by the AP in the current channel and
the expected time of the first Beacon frame transmitted by the AP in the
new channel.
IEEE P802.11be/D7.0, 35.3.11 (ML procedures for (extended) channel
switching and channel quieting) indicates that if an AP affiliated with
an AP MLD is switching channel, Max Channel Switch Time element shall be
included in every Beacon and Probe Response frame it transmits.
Add support to include the Max Channel Switch Time element in Beacon and
Probe Response frames during channel switch announcement for an AP
affiliated with an AP MLD.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
