To implement an action script that listens for DPP push button events
and for example blinks a LED it is useful to know when push button has
started. Emit an event when push button starts.
Signed-off-by: Evan Benn <evan.benn@morsemicro.com>
This is needed to allow some cases where puncturing prevents HT/VHT/HE
from using the full channel bandwidth.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is needed to be able to check validity of the channel parameters
for cases where EHT puncturing impacts what can be enabled for
HT/VHT/HE.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The testing functionality for overriding EHT puncturing bitmap was
applied only for the EHT elements. The mac80211 has been updated to
enforce compartibility between EHT and HT/VHT information and that made
the related test cases fail. Apply the override value for VHT element
generation to avoid some of those issues.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
A previous workaround was used to move the special operating class 130
to the end of the Supported Operating Classes element to avoid getting
any following entry being ignored or misunderstood. That is not really
the correct way of encoding the special cases, i.e., 80+80 MHz channels
that use two nonadjacent frequency segments.
Add support for encoding the 80+80 MHz channel with the 2-octet
operating class design using the Operating Class Duple sequence field of
the Supported Operating Classes element instead of listing the operating
classes that have the 80+ behavior limit set indication in Table E-4
(i.e., opclass 130 and 135) as 1-octet operating classes in the
Operating Classes field.
Fixes: a92660a00e ("Work around Supported Operating Classes element issues for 6 GHz")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Commit 085a3fc76e ("EHT: Add 320 channel width support") added this in
various places, but it did not cover everything. Extend this support to
be more complete. In particular, this allows wpa_supplicant to report
the operating class 137 in the Supported Operating Classes element and
to use it when processing beacon requests.
Signed-off-by: Ainy Kumari <quic_ainykuma@quicinc.com>
short_ssid in the own neighbor report might get out of sync, causing
advertising RNR element based on the old SSID, when SSID is changed
either with control interface command SET or with SIGHUP. Therefore,
sync the own report entry by removing the old entry and setting own
report again if the short SSID value has changed.
Signed-off-by: Nikita Chernikov <nchernikov@maxlinear.com>
Once the non-AP MLD is added to the driver, the driver handles the
address translation so that hostapd receives Management frames with
SA/DA being translated into MLD MAC addresses.
If the Authentication frmae is retransmitted with transaction being 1,
SA of the retransmitted Authentication frame is translated into the MLD
MAC address by the driver, and then in the function handle_auth(),
sta->mld_info.links[].peer_addr would be replaced by the MLD MAC address
even though it is supposed to be the link address.
Therefore, update the MLD information only when the STA has not yet been
added into the driver to avoid replacing the previously determined link
address with the MLD MAC address.
Fixes: bcbe80a66 ("AP: MLO: Handle Multi-Link element during authentication")
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
In theory, os_snprintf() could return a negative value and as such,
os_snprintf_error() should be used in all cases where the buffer might
not be large enough.
Signed-off-by: Jouni Malinen <j@w1.fi>
The event indicating expiration of an offchannel TX is useful for cases
where the wait is for a frame that was explicitly requested to have the
pending cookie to be saved.
Signed-off-by: Jouni Malinen <j@w1.fi>
Most places in the codebase use a valid_links bitmask with an array.
Switch the bss->links array to use the same design with the Link ID
being used as the array index instead of having a link_id inside.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
This was done using the below semantic patch. There are a few more
places that were missed due to variable declarations or additional
checks in the for loop.
@@
iterator name for_each_link;
identifier max_links =~ "MAX_NUM_MLD_LINKS|MAX_NUM_MLO_LINKS";
expression links;
expression further_tests;
identifier i;
statement stmt;
@@
-for (i = 0; i < max_links; i++)
+for_each_link(links, i)
{
(
- if (!(links & BIT(i)))
- continue;
...
|
- if (!(links & BIT(i)) || further_tests)
+ if (further_tests)
continue;
...
|
- if (further_tests || !(links & BIT(i)))
+ if (further_tests)
continue;
...
|
- if (links & BIT(i))
stmt
|
- if (further_tests && (links & BIT(i)))
+ if (further_tests)
stmt
|
- if ((links & BIT(i)) && further_tests)
+ if (further_tests)
stmt
)
}
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
This is a simple macro iterating the given bitmask using the given
variable. Having the macro avoids the for loop-continuation making it
more readable overall.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
In some places the wrong index variable was used to access the link
configuration. Fix this by simply using link_id instead of i.
With this, the i loop variable is not needed anymore. We can simply
always pass 0 to nla_nest_start(). Also, the kernel does not care about
the order that the links are provides, so just remove the special
handling for the association link.
Fixes: a2c4c0b1b6 ("nl80211: Support MLD association request")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
When a device supports both the 5 GHz band and the 6 GHz band,
these are reported as two separate modes, both with mode set to
HOSTAPD_MODE_IEEE80211A. However, as these are different modes,
each with its own characteristics, e.g., rates, capabilities etc.,
specifically differentiate between them by adding a flag to indicate
whether the mode describes a 6 GHz band capabilities or not.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
When wpa_supplicant assigns the IP address (WFA EAPOL IP address
allocation feature), the assigned IP address of the P2P Client on the GO
side is notified in the AP-STA-CONNECTED event. So to obtain the IP info
to external programs, modify the STA authorized event to include the the
assigned IP address of the P2P Client.
Test: Establish P2P connection and verified from the logs that
the P2P Client IP address is notified.
Signed-off-by: Sunil Ravi <sunilravi@google.com>
For AP MLD cases, the link id is required to determine the correct link
to stop in the stop_ap() driver op.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
The check for the non-AP MLD link being valid can be done one level
outside the loop that tries to find a matching AP link.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
For non-AP MLDs, clear STA entry from all affiliated links.
For legacy non-MLO case, find association link to clear the STA entry.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
This adds initial parts for RADIUS/TLS support in the RADIUS client.
This can be used with eapol_test and hostapd. This functionality is not
included by default and CONFIG_RADIUS_TLS=y in .config can be used to
enable it.
This version does not yet include all the needed functionality for TLS
validation and the rules for dropping a TCP connection based on invalid
RADIUS attributes.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is only one connection in use in parallel to a RADIUS
authentication server (and similarly to a RADIUS accounting server). As
such, there is not really any need to maintain separate open IPv4 and
IPv6 sockets. Instead, open the socket for the appropriate IP version
only when actually connecting to a specific server.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need for passing the sock and sock6 parameters separately
since they were always the same values for auth == 0 or auth == 1 cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
ETHER_VLAN_ENCAP_LEN does not seem to be defined in macOS
net/ethernet.h, so define that, if needed, to avoid build issues.
Fixes: 5b21f4861c ("l2_packet_freebsd: Enable receiving priority tagged (VID=0) frames")
Signed-off-by: Jouni Malinen <j@w1.fi>
When the station (non-AP MLD) is associated with an AP MLD the link ID
for TDLS setup is derived from the discovery response frame and the link
ID is used in TDLS setup operation when acting as initiator. The driver
sends the received discovery response frame followed by the TDLS setup
request event. But the discovery response frame is received after the
setup request event leading to use incorrect link ID value for TDLS
setup operation causing the setup failure. Process the TDLS setup
request if the discovery response frame is received, else defer the
process until the discovery response frame is received and process the
setup request after discovery response frame is processed.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When the CHAN_SWITCH command is executed during multi BSSID case (say
BSS1, BSS2, and BSS3), if one of the BSS is disabled (say BSS2), the
CHAN_SWITCH command returns an error in BSS2 and does not proceed to the
next BSS (BSS3).
The CHAN_SWITCH command handler iterates over all configured BSSs and
attempts to send the switch_channel to each one. However, if any one of
the BSSs fails, the entire command is aborted and returns a failure.
Continue the iteration even if one BSS is failing to make sure the
configuration is applied to other BSSs.
Signed-off-by: Haribabu Krishnasamy <quic_hkr@quicinc.com>
During high battery voltage scenario, higher MCS data rate leads to poor
EVM accuracy which causes poor user experience. Hence to provide better
user experience, EVM accuracy needs to be improved by adjusting TX power
for MCS rate of specific band/radio chain. To achieve this, add a new
vendor command to configure required parameters in the WLAN driver.
Signed-off-by: Mukul Sharma <quic_mukul@quicinc.com>
Add hostapd support for interacting with the NAN discovery engine to
allow single-channel (i.e., the AP's operating channel) USD as Publisher
or Subscriber.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add wpa_supplicant support for interacting with the NAN discovery engine
to allow USD as Publisher or Subscriber.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add NAN discovery engine and wpa_supplicant interface to use it for the
subset of NAN functionality that is needed for USD.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This was missing a check for the Category field and could have matched
other Action frames than Public Action frames.
Fixes: 9c2b8204e6 ("DPP: Integration for hostapd")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The standard is somewhat unclear on whether the PMKIDs used in
(Re)Association Request frame (i.e., potential PMKIDs that could be used
for PMKSA caching during the initial mobility domain association) are to
be retained or removed when generating EAPOL-Key msg 2/4.
wpa_supplicant has replaced the PMKID List contents from (Re)Association
Request frame with PMKR1Name when generating EAPOL-Key msg 2/4 for FT.
Allow it to be configured (ft_prepend_pmkid=1) to prepend the PMKR1Name
without removing the PMKIDs from (Re)Association Request frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
The standard is somewhat unclear on whether the PMKIDs used in
(Re)Association Request frame (i.e., potential PMKIDs that could be used
for PMKSA caching during the initial mobility domain association) are to
be retained or removed when generating EAPOL-Key msg 2/4.
hostapd used to require that only the PMKR1Name is included in the PMKID
List of RSNE in EAPOL-Key msg 2/4. Extend this to allow the PMKIDs that
were included in the (Re)Association Request frame to be present as long
as the correct PMKR1Name is also present. This would allow PMKSA caching
to be used in initial mobility domain association with supplicant
implementations that insert the PMKR1Name without removing the PMKIDs
used in the (Re)Association Request frame. wpa_supplicant did not use to
that, but other implementations might.
Signed-off-by: Jouni Malinen <j@w1.fi>
For some implementation, there is no link id in EAPOL event, e.g., use
drv_event_eapol_rx for receiving. Current design for such case is switch
to a link that stores the peer. However, this is error-prone because for
non-AP MLD case, sta_info is stored in all valid links but EAPOL sm is
only initialized in the association link. If EAPOL RX event is handled
in a non-association link, it will be discarded and this leads to EAPOL
timeout.
So find the association link to handle received EAPOL frame in such
case. This replaces the previously used workaround for RSN/wpa_sm for
the no link id specified case.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
Disabling the first interface calls hapd_deinit(), which causes some
issues, e.g., failure when trying to disable other interfaces due to
NULL drv_priv.
So check that all other interfaces are already disabled before disable
the first interface.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
When association is handled in hostapd, a non-AP MLD's info is stored in
all valid links. This should be the same when SME is offloaded to the
driver.
Also skip some operations that are already done by the driver
when SME is offloaded.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
Return the result from the first hostapd_is_usable_chan() call instead
of the following attempts in case of ht40_plus_minus_allowed to have
consistent behavior with the case where only one option is specified.
This allows the fallback to 20 MHz to work in additional cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When ACS offloaded to the driver, the channel selected event carries
link id to specify the link if operating as AP MLD.
Find the specified link to handle this event.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
ACS is triggered per link, so link id is needed for the driver to handle
when the ACS operation is offloaded.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
Currently, AID is not allocated properly in hostapd for legacy non-MLD
STA in case of an AP MLD. All such stations have same AID.
Fix this issue by allocating AID properly in hostapd when operating as
an AP MLD and the STA is not an MLD.
Fixes: d924be3bd0 ("AP: AID allocation for MLD")
Signed-off-by: Harish Rachakonda <quic_rachakon@quicinc.com>
This is an event indicating to the user space to disassociate with
peer based on the peer MAC address provided.
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
OpenSSL 3.2 added support for HPKE. Use that implementation when
possible. At least for now, the internal version needs to be included as
well to be able to cover the special DPP use case with brainpool curves.
Signed-off-by: Jouni Malinen <j@w1.fi>
The use of a MAC KDE in the Key Data field of an EAPOL-Key Request frame
was only for the STAKey handshake. That handshake was implemented in
2005 as an experimental functionality and it was then removed in 2006.
However, this part of the functionality was forgotten. This does not do
anything in practice, so simplify the implementation and remove it.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Encrypted Key Data field need to be set to 1 whenever using an AEAD
cipher. Without this, the Authenticator would discard the EAPOL-Key
request frame when using FILS.
Signed-off-by: Jouni Malinen <j@w1.fi>
EAPOL-Key request is accepted only if the MIC has been verified, so PTK
must have already been derived and Secure=1 needs to be used. Check the
Secure bit explicitly for completeness even though the MIC verification
is already taking care of validating that the sender is in the
possession of valid keys.
Signed-off-by: Jouni Malinen <j@w1.fi>
While the Authenticator state machine conditions are already checking
for sm->EAPOLKeyRequest, it seems clearer to explicitly discard any
EAPOL-Key Request frame that is received unexpectedly during a 4-way
handshake.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to try to process the EAPOL-Key frame if it has an
unexpected Key Descriptor Version value. Move these checks to happen
earlier in the sequence. In adition, use a separate helper function for
this to simplify wpa_receive() a bit.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check that the EAPOL-Key frame Key Descriptor Version value is one of
the defined values explicitly instead of failing to process the Key Data
field later (or end up ignoring the unexpected value if no processing of
Key Data is needed).
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2020 describes the rule based on not-TKIP for value 2
and no pairwise cipher condition on value 3, so use that set of more
generic rules here.
Signed-off-by: Jouni Malinen <j@w1.fi>
In hostapd_set_freq_params(), if center_segment0 is 2, call
ieee80211_chan_to_freq() with operating class 136 instead of 131.
This is needed because, channel 2 is an exception in the 6 GHz band. It
comes before channel 1 and is part of operating class 136.
Channels order in 6 GHz:
2 (Operating Class 136)
1 5 9 .... (Operating Class 131)
Signed-off-by: Thirusenthil Kumaran J <quic_thirusen@quicinc.com>
Add a new attribute for
%QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION subcommand. This
attribute is an 8 bit unsigned value used to specify whether an
associated peer is a QCA device.
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
If a GAS response is received for a pending SD query, process it even if
the TX status event for the query has not yet been received. It is
possible for the TX status and RX events to be reordered especially when
using UML time-travel, so this is needed to avoid race conditions to
make SD more robust.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
If both 6 GHz and S1G channels are included, the previously used timeout
was not long enough at least with mac80211_hwsim. Increase the initial
timeout to allow such a scan to be completed.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This makes it a bit easier to understand what happens with random
channel selection after radar detection.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
QCA_WLAN_VENDOR_ATTR_CONFIG_AP_ALLOWED_FREQ_LIST needs be to set per
link if operating as an AP MLD.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
It looks like best might be NULL in some cases, so check for this
explicitly before trying to dereference it for a debug print.
Fixes: 733de85680 ("ACS: Fix not selecting the best channel in the segment")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
key_data_buf is already freed on the common exit path, so do not try to
free it here on error.
Fixes: 4abc37e67b ("Support Key Data field decryption for EAPOL-Key msg 2/4 and 4/4")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
src/ap/ap_config.c is not really supposed to call directly into a
function in hostapd/config_file.c. Furthermore, the wrapper through
ap_config.c did not really have any real value since it just called a
function that is within hostapd/*.c and that wrapper was called from
hostapd/*.c.
Instead of the wrapper, just call the function directly within the
hostapd directory.
Fixes: 392114a179 ("FT: Add dynamic reload of RxKH definitions from file")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
peerkey from EVP_PKEY_new() needs to be freed on all error paths.
Fixes: b062507670 ("OpenSSL: Implement crypto_ecdh routines without EC_KEY for OpenSSL 3.0")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
If the driver fetch for the current sequency number fails, do not try to
print the value in a debug print without having cleared it.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Radar detection event could have resulted in the driver interface
instance getting deinitialized and the related memory freed in the
middle of the loop. This was not an issue when the event was passed only
into a single interface, but it became an issue when the loop tried to
send it to all interfaces. If the driver were removed, that loop check
would have used freed memory. Avoid this by explicitly checking that the
driver interface instance is still valid.
Fixes: f136837202 ("nl80211: Pass wiphy events to all affected interfaces")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The TX status handler for DPP Authentication Confirm message might have
resulted in use-after-free if the start of a GAS query were to fail,
e.g., due to being somehow unable to transmit the initial request. Avoid
this by explicitly confirming that the authentication session was not
removed.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The current connection (struct dpp_connection) might get removed during
the dpp_tcp_send_msg() call, so the code setting the
on_tcp_tx_complete_remove flag needs to check whether that happened to
avoid a potential use-after-free.
Fixes: 33cb47cf01 ("DPP: Fix connection result reporting when using TCP")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When removing the bootstrap info for the PB context, all the possible
pointers to that information needs to be cleared to avoid accesses to
freed memory.
Fixes: 37bccfcab8 ("DPP3: Push button bootstrap mechanism")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When the privacy protected itentity is used for EAP-SIM/AKA, the buffer
containing the identity was freed just before its use. Fix that by
reordering the operations.
Fixes: 881cb4198b ("EAP-SIM/AKA peer: Simplify identity selection for MK derivation")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
nl_socket_get_cb() increases cb_refcnf for the cb that is bound to a
socket and as such, nl_cb_put() needs to be used with the returned cb
after having cloned it to avoid leaking memory due to cb_refcnt never
getting back to 0.
Fixes: da0d51fee7 ("nl80211: Use socket cb instead of global->nl_cb in send_and_recv()")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The OpenSSL 3.x version of crypto_ec_key_parse_priv using
OSSL_DECODER_CTX missed the call to free the context. Fix it to avoid a
memory leak.
Fixes: 4f4479ef9e ("OpenSSL: crypto_ec_key_parse_{priv,pub}() without EC_KEY API")
Signed-off-by: Jouni Malinen <j@w1.fi>
Use smaller variables when possible and reorder the variables to avoid
unnecessary padding. This drops struct mld_link_info size from 64 to 48
bytes and removes 240 bytes from struct sta_info.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function has been used only within beacon.c and it got accidentally
converted to a global function.
Fixes: 6b5e00a80e ("AP: Use a struct for Probe Response generation in/out params")
Signed-off-by: Jouni Malinen <j@w1.fi>
Replace the fixed length maximum buffer size for STA profile with
dynamically allocated buffers for active links. This reduces struct
mld_link_info size by almost 16 kB and drops the per-STA information in
struct sta_info to a more reasonable size to avoid the almost 10x
increase from MLO support.
In addition, free the resp_sta_profile buffers as soon as the ML element
has bee generated for (Re)Association Response frame since those buffers
are not needed after that.
Signed-off-by: Jouni Malinen <j@w1.fi>
The singleton RADIUS client design did not address the deinit path
properly. Since hapd->radius could be shared with another links, the
pointer on all those other links needs to be cleared before freeing the
RADIUS client context. Without this, deinit path could have ended trying
to use freed memory when clearing STA entries from other links and
trying to flush any pending RADIUS client messages.
Fixes: a213fee11d ("AP: MLO: Make IEEE 802.1X SM, authserv, and RADIUS client singletons")
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow the Timeout Interval Type field in the Timeout Interval element to
be overridden with a different value for testing purposes to be able to
bypass the association comeback processing in mac80211. This allows the
wpa_supplicant internal functionality to be tested.
Signed-off-by: Jouni Malinen <j@w1.fi>
- CMAC and GMAC modes
- 128-bit and 256-bit modes
- normal BIP and BIP using BCE
- test vectors with minimum and optional additional header elements in
S1G beacon frames
- S1G Beacon Compatibility element in some cases, no other beacon body
components
Signed-off-by: Henry Ptasinski <henry@e78com.com>
Signed-off-by: Andrew Pope <andrew.pope@morsemicro.com>
Signed-off-by: David Goodall <dave@morsemicro.com>
hostapd reads the list of Rx Key Holders from hostapd.conf file.
However, for systems where topology changes dynamically, the update
of RxKHs list is required without reloading the whole configuration.
Introduce a new source of RxKH definition with original syntax:
- rxkh_file - Path to a file containing a list of RxKHs.
In addition, add a control interface command RELOAD_RXKHS to
reload RxKHs definition from the file specified in `rxkh_file`.
This allows hostapd to properly distribute Rx keys even after topology
change (assuming rxkh_file is updated and reload_rxkhs command issued).
Syntax of rxkh_file is the same as extraction of r0kh and r1kh options
from original hostapd.conf file.
```
r0kh=ff:ff:ff:ff:ff:ff * 00112233445566778899aabbccddeeff
r0kh=ff:ff:ff:ff:ff:ff * 00112233445566778899aabbccddeeff
r1kh=00:00:00:00:00:00 00:00:00:00:00:00 00112233445566778899aabbccddeef
r1kh=00:00:00:00:00:00 00:00:00:00:00:00 00112233445566778899aabbccddeef
r1kh=00:00:00:00:00:00 00:00:00:00:00:00 00112233445566778899aabbccddeef
```
Signed-off-by: Dariusz Kopka <dariusz@plume.com>
Smartcard support uses the ENGINE API of OpenSSL, which has been
deprecated as of OpenSSL 3. Rather than migrating the code to the new API
or pretending that we do not support OpenSSL 3, accept that we use
deprecated functionality.
Signed-off-by: Jouke Witteveen <j.witteveen@gmail.com>
NL80211_WPA_VERSION_3 was only added in kernel 5.2 so it should not be
set for older kernel versions. There is no direct way to check if the
value is supported. However, we can use the new infrastructure to check
whether the kernel has the NL80211_ATTR_SAE_PASSWORD attribute. It is
related and was added at the same time.
Fixes: 6cc78b3945 ("nl80211: Set NL80211_WPA_VERSION_2 vs. _3 based on AKM")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Now that we have a more advanced check for the differences within the
Key Data field, nonzero Key Data Length case can be determined to be
EAPOL-Key msg 4/4 if there is no RSNE in the Key Data field.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow the Key Data field to be encrypted in EAPOL-Key msg 2/4 and 4/4.
This is for testing purposes to enable a convenient mechanism for
testing Authenticator behavior with either potential future extensions
or unexpected Supplicant behavior.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend RSN authenticator to be able to process EAPOL-Key msg 2/4 and 4/4
messages in cases where the Key Data field is encrypted using AES key
wrapping (i.e., non-AEAD cipher). While there is not yet any defined
case where such encryption would be used in IEEE Std 802.11-2020,
extensions are considered to be added to use such constructions (e.g.,
in IEEE P802.11bh). As such, it is good to extend the parsing and
processing rules in the authenticator to be ready for such
functionality.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow additional elements and KDEs to be added to EAPOL-Key msg 2/4 and
4/4. This is for testing purposes to enable a convenient mechanism for
testing Authenticator behavior with either potential future extensions or
incorrect Supplicant behavior.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The initial Authenticator implementation depended on the Key Data field
being empty for EAPOL-Key msg 4/4. This worked fine for years in
practice, but in theory, vendor specific elements or KDEs could have
been added inti EAPOL-Key msg 4/4 and that would have broken this
design. In addition, the MLD case did introduce a KDE into EAPOL-Key msg
4/4 and required changes here.
As an initial step to make this more robust for future extensions,
recognize a received EAPOL-Key message as msg 4/4 if it is for RSN
(i.e., not WPAv1), has Secure=1, contains an unencrypted Key Data field,
and does not include RSNE.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow additional elements and KDEs to be added to EAPOL-Key msg 1/4 and
3/4 and allow EAPOL-Key msg 3/4 Key Data field to be not encrypted.
These are for testing purposes to enable a convenient mechanism for
testing supplicant behavior with either potential future extensions or
incorrect Authenticator behavior.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Handle the center frequency to channel mapping more cleanly by skipping
the cases where the center frequencies are not set and verifying that
the mapping succeeds when they are set.
Signed-off-by: Jouni Malinen <j@w1.fi>
seg0 and seg1 variables can have any initial value, but they may cause
the BSS to have a wrong configuration later on in cases where the
separate center frequencies are not set.
Signed-off-by: Baligh Gasmi <gasmibal@gmail.com>
When p2p->state == P2P_LISTEN_ONLY, the statement before it
'p2p->cfg->is_p2p_in_progress(p2p->cfg->cb_ctx)' will be true, too, so
this function will print a message "Operation in progress" and return;
the workaround to handle listen failure will be never reached.
I met such an error when the 'remain-on-channel' command failed, then
the function p2p_ext_listen_timeout() just printed 'Operation in
progress' again and again, and the listen operation was not started
anymore.
Fixes: 0f1034e388 ("P2P: Refrain from performing extended listen during P2P connection")
Signed-off-by: zhuhai <zhuhai.mail@163.com>
There are multiple redundant MIN macro declarations, some of which are
not protecting against side effects. Move it to common.h instead.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The kernel will reject commands if newer attributes are included even
though they should not be. Add appropriate checks in set_ap().
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Older kernel versions may not support all attributes and may refuse
commands that include them. To avoid sending too new attributes query
the highest supported attribute. This allows adding appropriate checks
where needed.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Previously, we would only pass the event to the first interface that
matches. However, one wiphy can have multiple interfaces and each one
needs to get the event delivered. Without this, it could e.g. happen
that a radar detection event is forwarded to p2p-dev-wlan0 and not to
the wlan0 interface which actually needs it.
As such, keep iterating if we are processing a wiphy match and send the
event to all affected BSSs.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
The dpp_test DPP_TEST_STOP_AT_AUTH_CONF case is supposed to prevent the
GAS exchange from happening. It was possible to bypass that testing
functionality if the TX status event for the Authentication Confirm
message was lost or delayed long enough for the GAS Request to be
proessed first. This could happen at least with UML time travel.
Work around this by checking for the special dpp_test case within GAS
request handling.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was done with spatch using the following semantic patch and minor
manual edits to clean up coding style and avoid compiler warnings in
driver_wext.c:
@@
expression a,b;
@@
- os_memcmp(a, b, ETH_ALEN) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- os_memcmp(a, b, ETH_ALEN) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !os_memcmp(a, b, ETH_ALEN)
+ ether_addr_equal(a, b)
Signed-off-by: Jouni Malinen <j@w1.fi>
Missing array referencing ended up only the first entry in the list to
be compared.
Fixes: 31fcea931d ("WPS 2.0: Add support for AuthorizedMACs attribute")
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes a code more readable for the large number of cases that use
os_memcmp() to check whether two ethernet addresses are equal.
Signed-off-by: Jouni Malinen <j@w1.fi>
If CONFIG_FILS isn't set, the compiler complains about unused variables.
Fix it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Fix commit 5545d995b3 which could use undefined symbol
testing_fail_alloc() in os_malloc() if CONFIG_WPA_TRACE=y is used
without CONFIG_WPA_TRACE_BFD=y.
Fixes: 5545d995b3 ("trace: Share common implementation for TEST_FAIL and TEST_ALLOC_FAIL")
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
The AP MLD MAC address is meant to be preserved here, but since it's
reset to zeroes before attempting to authenticate in
nl80211_mark_disconnected(), we can't just point to the AP MLD MAC
address in drv->auth_ap_mld_addr. Fix it by using a copy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a station tries to authenticate to an AP that is affiliated with an
AP MLD, we need to remove all station instances from all the APs.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
If the station is not an MLO station do not attempt to find the
association station and return false in the ML specific disconnection
processing.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This avoids unnecessary code duplication and adds the sta->wpa_sm deinit
calls for deauthentication while it was previously done only in the
disassociation case.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Set the current value instead of hardcoded 1.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
cfg80211 requires the link ID to be specified for requests to start a
remain-on-channel operation during an ML association. This feels wrong
since the ROC operation is in most cases unrelated to the
association. However, that requirement has been in place since kernel
commit 7b0a0e3c3a88 ("wifi: cfg80211: do some rework towards MLO link
APIs") from April 2022, and as such, it looks necessary to have
wpa_supplicant work around this by specifying the currently used link ID
that would seem to match the ROC channel most closely.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Commit 31e025c033 ("AP: When sending Action frames, use the AP MLD MAC
address if needed") added this for hostapd_drv_send_action(), but the
A3=BSSID variant of that function needs similar changes for GAS to work
correctly with STAs that are currently associated with MLO.
Signed-off-by: Jouni Malinen <j@w1.fi>
Invert the check on hapd->conf->mld_ap on the affiliated links to
actually call the link specific callback handler. This is needed to set
the STA associated.
Fixes: 55038680a6 ("AP: MLO: Handle association callback")
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to allow RSN operations, like PTK rekeying, to be
completed on the correct STA entry. The previous design worked by
accident since it was using the WLAN_STA_ASSOC flag and the code that
was supposed to set that flag did not work correctly and left it unset
for the interfaces that were not used for the initial 4-way handshake.
That needs to be fixed, so this search need to be extended to be able to
prefer the STA entry that has sta->wpa_sm set instead of just the
WLAN_STA_ASSOC flag.
Signed-off-by: Jouni Malinen <j@w1.fi>
The change to use a helper function for checking he_6ghz_reg_pwr_type
missed the difference between two types of checks for different values:
indoor AP vs. SP AP. Fix this by introducing another helper function to
cover the indoor (i.e., SP and non-SP indoor cases).
Fixes: 121ccadeb4 ("AP: A helper function for determining whether the AP is an SP AP")
Signed-off-by: Jouni Malinen <j@w1.fi>
There are bandwidth 320 MHz-1 and 320 MHz-2 channelization in EHT mode.
When using ACS, user might prefer one of the channelization or both, but
original ACS was unable to take such preference.
Another problem is that the original ACS returns only the ideal channel
but no 320 MHz channelization. The function acs_get_bw_center_chan()
also could not correctly return the center frequency of bandwidth 320
MHz that is decided by ACS.
For example, if ACS decide the ideal channel is channel 37 with
channelization 320 MHz-2 (center frequency 6265 MHz),
acs_get_bw_center_chan() returns 6105 MHz, which is 320 MHz-1.
Extend the support for 320 MHz so that ACS can choose the best channel
according to the user's preference. Also, after calling
acs_find_ideal_chan_mode(), the best channel and bandwidth can be
derived.
The changes are:
- bw_type ACS_BW320 is divided into ACS_BW320_1 and ACS_BW320_2
- in bandwidth 320 MHz, find the best channel and bandwidth according to
user's perference (320 MHz-1, 320 Mhz-2 or both are OK)
- before acs_find_ideal_chan_mode() returns, update bw320_offset in
iface->conf so that the best channel's channelization is recorded.
- get the best center frequency from bw320_offset
Co-developed-by: Money Wang <money.wang@mediatek.com>
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Introduce a new configuration option, "eht_bw320_offset", which enables
devices to specify a preferred channelization for 320 MHz BSSs when
using automatic channel selection (ACS). This option is applicable only
when the channel is not already decided and the bandwidth is set to 320
MHz.
The value and meaning of the option:
0: auto-detected by ACS
1: 320 MHz-1
2: 320 MHz-2
Co-developed-by: Money Wang <money.wang@mediatek.com>
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Fix the following bugs about selecting the best channels in the segment:
1. If the 'update_best' once became false, it never becomes true again.
In other word, if one of the channels in the segment is not usable,
the remaining channels in the segment were never able to be the best
channel.
2. The primary channel in the segment might not be usable due to the
insufficient survey data. Therefore, it cannot be the best channel and
we cannot take its factor/weight into account.
Co-developed-by: Money Wang <money.wang@mediatek.com>
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Allow ACS to pick a HT40- channel in the 2.4 GHz band in addition to the
previously hardcoded HT40+ case.
Co-developed-by: Money Wang <money.wang@mediatek.com>
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
This allows the function to be used outside the context of the
wpa_supplicant control interface implementation.
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
Previously only the SHA-1 -based AKM was supported. Extend that to cover
all PSK AKMs so that the PSK configuration to the driver happens for all
the possible cases during AP start.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
If the regulatory client EIRP PSD values advertised by an AP that is a
standard power AP or indoor standard power AP are insufficient to ensure
that regulatory client limits on total EIRP are always met for all
transmission bandwidths within the bandwidth of the AP’s BSS, the AP
shall also send a TPE element in Beacon and Probe Response frames as
that depicts the regulatory client EIRP limit.
Add support for this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
According to IEEE P802.11-REVme/D4.0, E.2.7 (6 GHz band), two Transmit
Power Envelope (TPE) elements need to be included by Indoor Standard
Power (Indoor SP) APs. Extend the code to support this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
According to IEEE P802.11-REVme/D4.0, 9.4.2.169.2 (Neighbor AP
Information field), the 20 MHz PSD subfield in the TBTT Information
field is a signed value with valid range of -127 to +126, while +127
indicates "no maximum transmit power is specified". Fix the default
value advertised.
Fixes: 3db24e4eef ("RNR: Define element format")
Fixes: a7c152d6b8 ("RNR: Add data from neighbor database")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add configuration options for setting the Tx Power value
in the Transmit Power Envelope for 6 GHz:
- The Tx power value for default client where the transmit
power interpretation is "Regulatory Client EIRP PSD"
- The Tx power value for subordinate client where the transmit
power interpretation is "Regulatory Client EIRP PSD"
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Update the HE regulatory information AP types based on IEEE
P802.11-REVme/D4.0. Set the default AP type to VLP. Check for valid
values when setting 'he_6ghz_reg_pwr_type' in the interface
configuration.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
In cases of SAE failure and testing, mgmt->sa was used for sending the
Authentication frame. Fix these to use the station address (which is
the MLD MAC address in cases of non-AP MLDs).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add a testing configuration such that the AP would be reported as
disabled in the RNR TBTT information MLD parameters included by other
affiliated APs of the AP MLD.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
An affiliated AP of an AP MLD can temporarily be disabled. Other
affiliated APs of the AP MLD indicate this in the Reduced Neighbor
Report (RNR) elements added to their Beacon and Probe Response frames.
When an affiliated AP is disabled, it should be included in the
association exchange, but can be activated only after it is enabled.
Add support identifying disabled APs and propagate the information
to the driver within the associate() callback.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add support for overriding EHT Operation element puncturing mask
for testing purposes.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
STA EHT MCS and NSS set field size shouldn't depend on AP HE operation
channel width. Fix it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
If the interface initialization fails, no links might be set when
calling the deinit functions. Those functions need to be prepared for
bss->n_links being 0.
Fixes: 859cbc396f ("nl80211: Remove links when stopping AP MLD in hostapd")
Signed-off-by: Jouni Malinen <j@w1.fi>
If the interface initialization fails, no links might be set when
calling the deinit functions. Those functions need to be prepared for
bss->flink being NULL.
Fixes: 47269be36e ("nl80211: Refactor i802_bss to support multiple links")
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a vendor attribute for EHT testbed STA to configure the
SCS traffic description support in the EHT capabilities of an
Association Request frame.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is an event indicating to the user space firmware page fault
summary report that the driver has generated from firmware indications.
This summary report is used to analyze major cause of page faults and
associated debug information.
Signed-off-by: Mukul Sharma <quic_mukul@quicinc.com>
Reorder the Element ID List to fill in the values in increasing order to
match the way the Element ID List is defined.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Currently while deciding to create a new Multiple BSSID element based on
the condition when the length reaches 255, the length value being used
is the total element length (including the length of the Element ID and
Length fields as well). However, the value in the length field denotes
the number of octets following it and excluding itself. Hence including
the total length is wrong. This leads to incorrect count of Multiple
BSSID elements.
And while filling the data, the length is considered porperly as it
should be hence we are filling more data in a single go and all data is
filled in MBSSID count which is less than originally calculated. This
ultimately leads to incorrect length calculation during nla_put() and
setting the beacon to the driver fails while putting the Multiple BSSID
element data into the netlink socket buffer.
Fix this issue by considering the length excluding the Element ID and
Length field sizes.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Share VLAN info in RRB when the driver advertises support for VLAN
offload (WPA_DRIVER_FLAGS_VLAN_OFFLOAD). sta->vlan_desc is unused in
this case, only sta->vlan_id is used. Skip the checks that are based on
sta->vlan_desc.
Signed-off-by: Sai Pratyusha Magam <quic_smagam@quicinc.com>
This helper is of no real use anymore, so get rid of it. This completes
send_and_recv*() cleanup. What remains is the most generic
send_and_recv() and two wrappers for it to cover the most common simpler
cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is a variant for the second most common case of send_and_recv() needs:
send a command with a special response handling.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is a variant for the most common case of send_and_recv() needs:
send a command without needing a special response handling. In addition,
move the helper functions into driver_nl80211.h since these are now
simple wrappers for the more flexible send_and_recv().
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is not really that helpful as a separate helper function, so get
rid of one of the many send_and_recv() variants.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is not helpful as a separate helper function anymore, so get rid of
one of the many send_and_recv() variants.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is independent of the NL80211_ATTR_SOCKET_OWNER use, so add these
attributes from a separate helper function that is called only from
locations that actually start an operation that uses EAPOL frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Doing this based on driver support for control port RX or SAE seems like
undesired extra complexity. Just use this in all cases where the special
handle for a longer term operation, like connection or AP mode
operation, is needed.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is a step towards cleaning up all the workarounds that have showed
up over the years and made the design difficult to understand. This
removes use of the separate registration of process_bss_event() as
NL_CB_VALID for the individual commands since the use of the appropriate
cb (i.e., the one from nl80211_init_bss() in these cases) will already
point to the correct handler.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is a workaround for some race conditions where the hardcoded use of
global->nl_cb in send_and_recv() ends up getting events delivered
through unexpected context when they happen to arrive at the time when a
command is being processed.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Avoid potential read of one or two octets beyond the end of the
subelement when verifying that there is sufficient amount of data
included in each subelement/element within the MLE in Association
Request frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of rejecting the Multi-Link element, skip unknown subelements to
be less likely to cause interop issues for future. IEEE P802.11be/D5.0
allows other optional subelements to be included here.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function is both updating the hostapd-internal sta->flags value and
sending out the AP-STA-CONNECTED control interface message. When
authorizing a STA, the call to this function is followed by a driver
command to update the flags of the STA entry in the driver. That has a
race condition at least for UML time-travel since the AP-STA-CONNECTED
event is used as a message to wait for before running a connectivity
test or some other operation that depends on the data connection being
in working condition.
Split the function into two steps so that the driver STA entry update
can be done between those two steps for the cases where it matters for
the race condition. In other words, send the AP-STA-CONNECTED message
only after having authorized the STA in the driver.
Signed-off-by: Jouni Malinen <j@w1.fi>
The check for extra data was not dereferencing the pointer, but avoid
complaints about such uses by freeing the decrypted data only after the
check. The hexdump could have read freed memory, so that needs to be
before the freeing.
Fixes: 54ac6ff8c4 ("PKCS 1: Add function for checking v1.5 RSA signature")
Signed-off-by: Jouni Malinen <j@w1.fi>
Even though this function is documented to always return 1, be more
consistent in checking that to avoid warnings from static analyzers.
Signed-off-by: Jouni Malinen <j@w1.fi>
This memcpy was causing warnings from static analyzers since it is being
misinterpreted as copying all the data into the lnkid.bssid[] array
instead of that and the following arrays. Since the copy is not needed
at all, just use the original pointer to get rid of these warnings.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that sta is not NULL before calling
hostapd_process_assoc_ml_info() that references this parameter. In
theory, sta might be NULL here if addition of the STA entry failed in
the 60 GHz case.
Signed-off-by: Jouni Malinen <j@w1.fi>
This line seemed to trigger SIGSEGV in some code coverage testing cases.
It is not exactly clear how that was possible, but just in case, check
that iface->current_mode is set before using it here.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the BSS TM Request for imminent BSS temoval is for a non-AP MLD that
has multiple affiliated links, do not schedule full disconnection since
other links remain associated.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow link removal imminent indication to be added with the new
link_removal_imminent=1 parameter to BSS_TM_REQ.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Based on IEEE P802.11be/D5.0, when a station is non-AP MLD with more
than one link the combination of the Link Removal Imminent field set to
1 and the BSS Termination Included field set to 1 means than only one of
the links is removed while the other links will remains associated.
Handle this case without starting a scan to find another BSS.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When the AP MLD sends an Action frame to a non-AP MLD, use the AP MLD
MAC address instead of the local AP address (BSSID).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When the AP is configured to operate as an AP MLD, use the AP MLD MAC
address when needed for transmission of WNM Action frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
If ioctl() returns EBUSY on the command SIOCBRADDIF, the interface might
have already been added to the bridge by an external operation (e.g.,
netifd in OpenWrt), and linux_br_add_if() should not indicate an error.
Check whether the interface is correctly brigded when ioctl()
returns EBUSY and if so, report success.
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Remove a spurious \tab char in hostapd_eid_rnr() between arguments to a
function.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In case the TBTT information is reporting about an AP in the same AP MLD
as the current AP, the AP MLD ID in the MLD Parameters subfield should
be set to 0.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Link ID needs to be specified for MLD case when doing channel switch.
Add it to the driver command.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
There are different CHAN_SWITCH flows for DFS and non-DFS channels.
Non-DFS one saves previous BW value in iface->conf, but DFS flow
replaces it with a new user requested value. Setting a non-DFS channel
after a DFS one with BW = 160 would have resulted in a mismatch between
the saved BW and vht_capab (if VHT160 was not included by default). This
would have led to a check fail in the hostapd_set_freq_params()
function.
Signed-off-by: Dmitrijs Martinovs <dmartinovs@maxlinear.com>
It is possible for the start_listen() callback to be called to request
the driver to start a driver operation and stop_listen() called
immediately after that (e.g., due to a request to transmit a P2P Public
Action frame) before the driver has had time to start ROC and send an
event to notify of that. Such a sequence could result in
p2p->pending_listen_freq being left to a nonzero value without getting a
call to p2p_listen_cb() to clear it. This would stop an ongoing P2P
listen operation since no following p2p_listen() call would start the
listen due to the pending command being assumed to be in effect.
Fix this by detecting this particular sequence and clearing
p2p->pending_listen_freq.
This was found with the p2p_listen_and_offchannel_tx test case with the
new kernel scheduled and UML time-travel.
Signed-off-by: Jouni Malinen <j@w1.fi>
With changes to optimize scan for specific BSSID, there arises a
scenario where in nl80211_trigger_scan() is called with a scan
randomization enabled. A combination of NL80211_ATTR_MAC for BSSID and
scan randomization, which uses NL80211_ATTR_MAC for a different purpose,
results in invalid error for the scan request. To fix the issue use
attribute NL80211_ATTR_BSSID instead of NL80211_ATTR_MAC.
NL80211_ATTR_BSSID was introduced in kernel commit 2fa436b3a2a7
("nl80211: Use different attrs for BSSID and random MAC addr in scan
req") in 2016. Prior to that, only NL80211_ATTR_MAC could be used for
specifying the target BSSID. For backwards compatibility, add the
NL80211_ATTR_MAC attribute as well when not using a random MAC address.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
The underlying driver can reject only specific links in an association
request. In that case we will only ignore the corresponding BSS. Add a
test for this flow by simulating an association failure on the second
link specifically.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
All the station flags other than WPA_STA_SHORT_PREAMBLE are relevant
only for the MLD station and not to the link stations (as these flags
are related to the MLD state and not the link state).
As for the WPA_STA_SHORT_PREAMBLE, since the station is an EHT
station, it must have short preamble.
Thus, do not propagate the flags change for link stations to the driver.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add additional check for 6 GHz operating class. Otherwise this results
in setting incorrect segment 0 index for 5 GHz 40 MHz channel 157-161,
which has the same center segment 0 index 159 as 6 GHz 320 MHz expected
channel.
Fixes: 085a3fc76e ("EHT: Add 320 channel width support")
Signed-off-by: Mikelis Vuls <mvuls@maxlinear.com>
Add a new QCA subcommand QCA_NL80211_VENDOR_SUBCMD_REGULATORY_TPC_INFO
and related attributes qca_wlan_vendor_attr_tpc_links,
qca_wlan_vendor_attr_tpc definition to query transmit power information
on STA interface from the driver for a connected AP.
The information includes regulatory max transmit power limit, AP local
power constraint advertised from AP's Beacon and Probe Response frames.
For PSD power mode, the information includes PSD power levels for each
subchannel of operating bandwidth. The information is driver calculated
power limits based on current regulatory domain, AP local power
constraint and other IEs. The information will be set to target. Target
will decide final TX power based on this and chip specific power
conformance test limits (CTL), and SAR limits.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
For AP MLD case, HT-scan and ACS happens per link. To determine the
correct link, link id is required.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
Removing radio measurements and supported operating class indication
might be needed to reduce binary size for a memory constrained system
that does not need more advanced features. However, removing these is
not recommended since they can help the AP manage the network and STA
steering.
By default this functionality is enabled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Beacon hinting is a feature that can temporarily change the regulatory
rule flags on the channel where the radio hears the beacon. Add a new
event CTRL-EVENT-REGDOM-BEACON-HINT to notify the wpa_supplicant user
about an important update to the regulatory rules including which
frequencies are impacted, new power limit, and new rule flags.
Signed-off-by: Jun Yu <junyuu@chromium.org>
Do not allow offchannel operation for action frame transmission if
no frequency is specified, as this doesn't make sense.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The length of the PMK ended up getting lost when a PMKSA cache entry was
added based on externally managed information. Set the PMK length in SAE
context to get the correct length stored into the actual PMKSA cache
entry that gets created in this path.
Signed-off-by: Jouni Malinen <j@w1.fi>
According to this message https://marc.info/?l=binutils&m=165363679302282
the type bfd_hostptr_t is dropped in favor of uintptr_t.
Replace the use of this type in the code.
Signed-off-by: Jaap Keuter <jaap.keuter@xs4all.nl>
USe the link ID information to determine the specific affiliated link
when processing channel switch events on an AP MLD.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
There is an issue when starting a non-MLD AP on the same interface that
previous operated as an AP MLD. When the previous AP MLD got stopped,
links were not removed when using hostapd. Next non-MLD AP will fail to
start because some nl80211 operations still require link id (e.g., set
freq).
Remove links when AP MLD is stop to avoid such issue. This was already
done in the deinit_ap() handler when using wpa_supplicant, but hostapd
needs to do same.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Do include group MLO KDEs for links for which the information is
missing.
In addition, set the KDE buffer length based on the added data.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The tag is inserted as the first item in the stack trace, making it
trivial to match against it from the test.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Refactor the backtrace matching a bit in order to allow triggering
multiple failures in one test.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Get rid of more or less duplicated implementation of backtrace matching
for the two testing failure cases.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Move the hostapd and wpa_supplicant control interface handlers into a
shared functions instead of duplicated implementation.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
When processing a (Re)Association Request frame and no corresponding
station is found, try to find the station using the station MLD MAC
address from the Basic ML element, as it is possible that the station
is trying to re-associate but with a different link address (in such
a case the underlying driver would not perform address translations).
When sending the (Re)Association Response frame, use the addresses from
the (Re)Association Request frame and not the AP MLD MAC address, again,
to avoid the address translation done in the driver.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
IEEE P802.11be/D4.0, 9.4.2.312.2.3 states that the AP MLD ID should only
be included in some ML probe responses. Beacon frames shouldn't include
AP MLD ID.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This responds by simply embedding most of the IEs from the other links
into the ML element. This is not correct really, as inheritance rules
should be applied and an inheritance element may need to be added.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add a simple for_each_mld_link helper that sets first variable to the
hapd data for every link. It takes the interfaces and MLD ID as
arguments and two extra integers as scratch variables (for the interface
and bss offsets).
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
This adds the parsing of ML probe requests. Handling will be added by a
later commit.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
To support ML probe request we will need to include IEs from the other
hapd instances in the response. Split the function to allow just
generating the per-instance IEs separately.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This effectively moves setting the csa/ecsa/cca position to happen
only when a Probe Response template for offloading is generated.
One could probably avoid the global variable altogether, as the
value is immediately consumed into struct {csa,cca}_settings.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
If a link specific error occured, mark the offending link within the
association parameters.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The kernel may report the link that caused an error by setting
NLMSGERR_ATTR_OFFS pointing to the NL80211_ATTR_MLO_LINKS element
that was the reason for the error.
Parse this information if the optional struct nl80211_err_info is
passed to send_and_recv_msgs().
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When the TX link rejects the association, return a status code for all
requested links. For simplicity, just return "TX link not accepted" so
that clients may try to connect to other links. This could be improved
to explicitly reject each link if directly associating to the link will
not work either.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add the new status code that had not yet been defined.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add support for testing ML link removal to hostapd. While such support
should inherently be integrated with the underlining driver, simulate
the inclusion of the ML reconfiguration element in hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Parsing multiple RNR elements already exists in
wpa_bss_parse_basic_ml_element(), so wpas_ml_element() just duplicates
the same code. Combine the functionality of both these functions and
remove the duplicate.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Three functions were provided for defragmentation. First
ieee802_11_defrag(), ieee802_11_defrag_mle() and then
ieee802_11_defrag_data() which would do the actual job. With
ieee802_11_defrag() picking the member in the elements struct for an
EID. The problem with this is, that for the Multi-Link element, there
are multiple entries in the elems struct depending on its type. As such,
remove the intermediate function and simply pass the correct members
directly.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This Presence Bitmap field is B4..B15 of the Multi-Link Control field
and the value used here is for that full 16-bit field, not just within
the Presence Bitmap field.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
With nl80211 we need to supress the kernel generated event for any
disconnect and deauthenticate. This code is a bit fragile, as it
assumes that an event will happen. Commit b898b65582 ("nl80211: Do
not ignore disconnect event in case of !drv->associated") changed this
to only disconnect when the driver knows it is associated (apparently
required for P2P), however, deauthentication may also occur without
being associated yet.
Looking at the issue, what we are really interested in is whether the
event belongs to a disconnect/deauth command that we have send
ourselves. Any event happening after the disconnect/deauth completes
should not be suppressed (or after the next connect/auth as that would
be sufficient). We therefore need to know from the event stream
whether events were generated before or after disconnect/deauth
command completion.
To do so, send a simple command on the nl_event socket. As this will
be returned back to us in the correct order with regard to the events.
We can therefore use it to safely reset our internal
ignore_next_local_{deauth,disconnect} variables.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Handling of port authorized event for STA currently handles the
connected BSSID. This needs additional handling to support the AP MLD
address in case of MLO connection. The connected_addr expected by
cfg80211_port_authorized() is mld_addr for ML connection case.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
Enable support for ACS in the IEEE 802.11be/320 MHz case. To do so we
just:
- add channel definitions for the 320 MHz blocks of the 6 GHz band
- handle CONF_OPER_CHWIDTH_320MHZ in the different cases
- restrict 320 MHz to ieee80211be=1 only
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Fix for the HE Channel Center Freq Seg0/Seg1 within the HE 6GHz
Operation Information field. As downgrade of bandwidths for VHT and HE
when using puncturing is TODO for 320 MHz and/or if puncturing is
disabled and bandwidth is 320 MHz, the same rules as for 160 MHz should
be applied for Channel Center Freq Seg0/Seg1 within 6 GHz Operation
Information field.
Signed-off-by: Jurijs Soloveckis <jsoloveckis@maxlinear.com>
Include EHT Operation Information field only if the operating bandwidth
is 320 MHz or there is at least one punctured 20 MHz subchannel. This
behavior is defined in IEEE P802.11be/D4.0, 35.15.1 (Basic EHT BSS
operation).
Signed-off-by: Jurijs Soloveckis <jsoloveckis@maxlinear.com>
The prime_len variable is used as the length in bytes but it is set as
the length in bits. This fixes the sae DH group tests with wolfSSL.
Fixes: f8f20717f8 ("SAE: Use const_time selection for PWE in FFC")
Signed-off-by: Juliusz Sosinowicz <juliusz@wolfssl.com>
