This allows previously configured network profiles to be used so
that user can indicate preference of manually configured networks.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can now be configured to filter out scan results based
on a BSSID filter. Space-separated set of allowed BSSIDs can be set
with wpa_cli set bssid_filter command. Filtering mechanism can be
disabled by setting this variable to an empty list. When set, only
the BSSes that have a matching entry in this list will be accepted
from scan results.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Extra parameter "no-connect" can now be added to the ENABLE_NETWORK
ctrl_iface command to avoid automatic connection to the enabled
network.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"wpa_cli set radio_disabled 1/0" can be used to disable/enable
radio to simulate out-of-radio-range condition in a testbed
device.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Normal scan is more reliable and faster for WPS operations and since
these are for short periods of time, the benefit of trying to use
sched_scan would be limited. This can fix WPS connectivity issues
with some drivers.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Commit d9a38716cc did this for
hostapd_eapol_tx_status() but missed the older hostapd_tx_status()
path. Address that case, too.
The TX status event may be received after a station has been
disassociated in cases where the disassociation is following a
transmission of a Data frame. Ignore such events if the STA is not
associated at the moment the event is being processed. This avoids
confusing debug entries and rescheduling of the EAPOL TX timeouts for
STAs that are still in the STA table, but are not really in active EAPOL
session.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
The SetSelectedRegistrar timeout was registered for each registrar
instance, but the only context pointer (struct subscription *) was
shared with each registrar which resulted in the timeout getting
cancelled for some of the registrar instances before the selected
registrar (ER) information was cleared.
In addition, when an ER unsubscribed from receiving events, the
selected registrar information got cleared only from a single
registrar.
Fix these issues by registering a pointer to the registrar
instance in the timeout and by iterating over all UPnP interfaces
when removing a subscription.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
eloop_sock_table_add_sock() needs to fail if pollfd array allocation
fails instead of returning success and leaving behind no buffer.
Signed-hostap: Jouni Malinen <j@w1.fi>
In IBSS RSN cfg80211/mac80211 now waits for userspace to authorize new
stations. This patch makes wpa_supplicant notify the driver when a
station can be considered authorized.
Signed-hostap: Antonio Quartulli <ordex@autistici.org>
When using more than around 200 virtual stations, we start hitting the
max number of file descriptors supported by select(). This patch adds
support for poll(), which has no hard upper limit.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Commit 3c85f144ce fixed issues with P2P
Action frame TX after disconnection by clearing wpa_s->assoc_freq.
This resulted in a regression to the post-WPS scan optimization that
used wpa_s->assoc_freq to enable fast single-channel scan. Fix this by
copying wpa_s->assoc_freq to a local variable before calling
wpa_supplicant_deauthenticate() that ends up calling
wpa_supplicant_mark_disassoc() which will clear assoc_freq.
Reported-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
intended-for: hostap-1
Signed-hostap: Jouni Malinen <j@w1.fi>
Remove the GPL notification text from files that were initially
contributed by Atheros Communications or Qualcomm Atheros.
Signed-hostap: Jouni Malinen <j@w1.fi>
Remove the GPL notification text from EAP-pwd implementation per
approval from Dan Harkins who contributed these files.
(email from Dan Harkins <dharkins@lounge.org> dated
Wed, 4 Jan 2012 16:25:48 -0800)
Signed-hostap: Jouni Malinen <j@w1.fi>
Simplify licensing terms for hostap.git by selecting the BSD license
alternative for any future distribution. This drops the GPL v2
alternative from distribution terms and from contribution requirements.
The BSD license alternative that has been used in hostap.git (the one
with advertisement clause removed) is compatible with GPL and as such
the software in hostap.git can still be used with GPL projects. In
addition, any new contribution to hostap.git is expected to be licensed
under the BSD terms that allow the changes to be merged into older
hostap repositories that still include the GPL v2 alternative.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since there is the method org.freedesktop.DBus.Properties.GetAll that
returns all properties from a specific interface, it makes more sense to
separate the properties to make it possible to get only a single
property using the method org.freedesktop.DBus.Properties.Get as well.
Signed-hostap: Flávio Ceolin <flavio.ceolin@profusion.mobi>
This fixes a build regression from commit
cd2f4ddfb9 by moving
wpa_supplicant_assoc_update_ie() outside the no-scan-processing ifdef
block.
Signed-hostap: Jouni Malinen <j@w1.fi>
In case of !defined(IEEE8021X_EAPOL) the definition of the stub
pmksa_cache_get() in rsn_supp/pmksa_cache.h is not correct. This patch
adds the missing argument to the function definition to fix a
regression from commit 96efeeb66b.
Signed-hostap: Antonio Quartulli <ordex@autistici.org>
Search (p2p_scan) could already have been started at the point
remain-on-channel end event is being processed, e.g., if an Action frame
TX is reported immediately aftet the end of an earlier remain-on-channel
operation and the response frame is sent using an offchannel operation
while p2p_find is still in progress. Avoid trying to re-run p2p_scan
while the previous one is still running.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 39185dfa54 changed the p2p_scan()
callback to return 1 in some cases, but forgot to change this p2p_scan()
call to handle that properly. Fix this by processing any non-zero value
as an error. This regression could leave the P2P module in state where
it believed a P2P scan was still running and refused to start some
operations until that scan gets completed (which would never happen
since it was not really started).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, PINs that are added with a wildcard UUID were allowed to
be used only by a single Enrollee. However, there may be more than one
Enrollee trying to connect when an AP indicates that active Registrar
is present. As a minimal workaround, allow two Enrollees to try to use
the wildcard PIN. More complete extension could use timeout and allow
larger set of Enrollees to try to connect (while still keeping in mind
PIN disabling requirement after 10 failed attempts).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The BSS ctrl_iface command can sow the age of a BSS table entry to
make it easier for external programs to figure out whether an entry
is still current depending on the use case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"BSS p2p_dev_addr=<P2P Device Address>" can now be used to fetch a
specific BSS entry based on the P2P Device Address of the GO to avoid
having to iterate through the full BSS table when an external program
needs to figure out whether a specific peer is currently operating as
a GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When a GO is operating a persistent group and invites a peer that has
been a P2P client in that persistent group, the Invitation Type in the
Invitation Request frame can be set to 1 to indicate that this is a
reinvocation of a persistent group. Do this based on the maintained
list of P2P clients that have been provided the credentials to this
group.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even though the Provision Discovery Response frame from PD-before-join
does not really provide any additional information, it can be better to
wait for it before starting the join operation. This adds a minimal
extra latency in the most common case and cleans up the sequence of
driver operations and debug log by avoiding potential processing of the
Provision Discovery Response while already running a scan for the actual
connection.
If transmission of Provision Discovery Request fails, join operation is
started without the additional wait. In addition, a new timeout is used
to start the join if Provision Discovery Response is lost for any
reason.
Signed-hostap: Jouni Malinen <j@w1.fi>
Provision Discovery is used as a notification to the GO in the case we
are about join a running group. In such case, there is not much point in
indicating the provision discovery response events to external programs
especially when the PIN-to-be-displayed was different from the one
returned for the p2p_connect command. Skip this confusing event
completely for join-a-running-group case.
Signed-hostap: Jouni Malinen <j@w1.fi>
When the GO negotiation peer is assigned, the state also cannot be IDLE,
SEARCH, or LISTEN_ONLY.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These changes account for situations where the CQM threshold
might be approximately the same as the currently received signal,
and thus CQM events are triggered often due to measurement
error/small fluctuations. This results in scanning occurring
too frequently.
Firstly, inhibit the immediate scan when the short-scan count
is at the maximum. This keeps bursts of CQM toggling from
causing a torrent of back-to-back scans. This does not inhibit
immediate scans if the CQM triggers a second time (if the signal
falls lower past the hysteresis). This reduces the scan rate in
the worst case (fast-rate toggling high/low CQM events) to the
short scan interval.
Secondly, change the behavior of the short scan count so it acts like
a "leaky bucket". As we perform short-scans, the bucket fills until
it reaches a maximal short-scan count, at which we back-off and
revert to a long scan interval. The short scan count decreases by
one (emptying the bucket) every time we complete a long scan interval
without a low-RSSI CQM event.
This reduces the impact of medium-rate toggling of high/low CQM
events, reducing the number of short-interval scans that occur before
returning to a long-interval if the system was recently doing
short scans.
Driver global init was considered a hard failure. Thus if, for example,
you used the Broadcom STA driver and didn't have nl80211 or cfg80211
loaded into the kernel, and specified a driver value of "nl80211,wext",
the nl80211 driver's global init would fail with the following message:
nl80211: 'nl80211' generic netlink not found
Failed to initialize driver 'nl80211'
but since global init was a hard failure, creating the supplicant
interface would fail and the WEXT driver would not be tried.
Give other drivers a chance instead.
Signed-hostap: Dan Williams <dcbw@redhat.com>
intended-for: hostap-1
The setter function uses the same hostapd_data structure as the getter
which causes it to crash if called on a P2P client. To overcome this
issue, the role is checked to ensure it is called on a group owner and
the pointer is examined for validity. The function will return an error
if called on a non-GO system.
Signed-hostap: Todd Previte <toddx.a.previte@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
intended-for: hostap-1
When using DBus to get group properties, a segmentation fault is
generated on P2P clients due to a NULL pointer for the ap_iface struct.
The current implementation only returns vendor extensions when called on
a P2P group owner.
The code now checks the P2P role which allows for role-specific
information to be provided. This also fixes the crash issue by only
looking for the correct structures based on the current P2P role.
Signed-hostap: Todd Previte <toddx.a.previte@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
intended-for: hostap-1
When looking for PMKSA cache entries to use with a new association, only
accept entries created with the same network block that was used to
create the cache entry.
Signed-hostap: Jouni Malinen <j@w1.fi>
The disconnection command results in disassociation and deauthentication
events which were previously processed during the scan in case of
select_network command being used while associated with another network.
While this works in most cases, it can result in confusing event
messages in ctrl_iface and debug log. Avoid this by using a short delay
between the disconnection and scan request to allow the disconnection
events to be processed prior to starting the new scan.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
This fixes a corner case where a STA that has PMKSA cache entry (or
valid FT keys) could try to use full EAPOL/EAP authentication and fail.
If the STA will then try to use the still valid PMKSA cache entry (or
FT) before the STA entry has been cleared, authFail could have been left
to TRUE. That will make EAPOL authenticator PAE state machine enter HELD
state even though authSuccess was already forced to TRUE. This results
in the STA getting disconnected even though it should be allowed to
continue with 4-way handshake. While this is unlikely to happen in
practice, it is better to get this fixed by clearing authFail when
setting authSuccess.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
The TX status event may be received after a stations has been
disassociated in cases where the disassociation is following a
transmission of a Data frame. Ignore such events if the STA is not
associated at the moment the event is being processed. This avoids
confusing debug entries and rescheduling of the EAPOL TX timeouts for
STAs that are still in the STA table, but are not really in active EAPOL
session.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
While the exponential increase in the lockout period provides an
efficient mitigation mechanism against brute force attacks, this
additional trigger to enter indefinite lockout period (cleared by
restarting hostapd) will limit attacks even further by giving maximum of
10 attempts (without authorized user action) even in a very long term
attack.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows HT capabilities overrides on kernels that
support these features.
MCS Rates can be disabled to force to slower speeds when using HT.
Rates cannot be forced higher.
HT can be disabled, forcing an 802.11a/b/g/n station to act like
an 802.11a/b/g station.
HT40 can be disabled.
MAX A-MSDU can be disabled.
A-MPDU Factor and A-MPDU Density can be modified.
Please note that these are suggestions to the kernel. Only mac80211
drivers will work at all. The A-MPDU Factor can only be decreased and
the A-MPDU Density can only be increased currently.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Now that CTRL-EVENT-TERMINATING even is sent at the end of interface
removal in case wpa_supplicant process is going to terminate, there
is no need for this duplicated event in the signal handler.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows TERMINATING ctrl_iface event to be sent at the end of the
deinit sequence to avoid race conditions with new operations that this
event may trigger while wpa_supplicant would still be running through
the deinitialization path.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This avoids issues with some external program starting to use the
interface based on the interface removal event before wpa_supplicant
has completed deinitialization of the driver interface.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This will be needed to be able to move ctrl_iface TERMINATING event to
the end of interface removal.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
