Use zero value with QCA_WLAN_VENDOR_ATTR_CONFIG_EHT_MLO_MAX_NUM_LINKS to
restore the device default maximum number of allowed MLO links
capability.
Also, as per IEEE 802.11be/D3.0, the maximum number of allowed links for
an MLO connection is 15. Update the documentation of the attribute to
indicate the same.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Define a struct to hold MLD station info and implement publishing of the
Basic Multi-Link element. Add it into Beacon and Probe Response frames.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
- Include RNR element in Beacon frames of AP MLDs.
- Whenever a new interface is added to an AP MLD, reconfigure
the Beacon frame templates for all other interfaces, to allow
updating their RNR elements.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
AP cannot come up in channels that are marked as NO_IR. If AP moves to
HAPD_IFACE_DISABLED state, it will deinitialize the nl80211 driver
interface and sockets.
Hence, introduce a new state called HAPD_IFACE_NO_IR, for 6 GHz APs to
handle NO_IR scenarios, such as AFC, where the channels not allowed by
AFC will have HOSTAPD_CHAN_NO_IR flag set. In this state, AP is still
kept in a non-operational state (stopped) without deinitializing the
nl80211 driver interface. wiphy reg change event can then update the
channels and bring up the AP in a valid channel.
Signed-off-by: Pooventhiran G <quic_pooventh@quicinc.com>
Define a QCA vendor command to configure MLO link id to the driver on
which the TDLS discovery response frame needs to be transmitted when the
local station is connected in MLO mode. This command is configured to
the driver the prior to every TDLS discover frame transmission when the
station is connected in MLO mode. If the station is connected in non-MLO
mode this command is not configured to the driver for TDLS discovery
frame transmission.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support to indicate link reconfiguration event reported by the QCA
vendor interface to the wpa_supplicant control interface.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support to indicate TID-to-link mapping changes reported by the QCA
vendor interface to the wpa_supplicant control interface.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Add a new vendor command and attributes to notify TID-to-link mapping
changes to the userspace.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Define a new QCA vendor attribute to configure channel bandwidth to the
driver for CTS frame transmission. This is used for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN in
enum qca_wlan_vendor_features to indicate the device supports enhanced
audio experience over WLAN feature.
Also, update the documentation where other subcommand(s) or attribute(s)
require this new feature flag. These subcommand(s) and attributes are
under development and would be restricted to the supported drivers
advertising QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN.
As such, it is still acceptable to introduce a new requirement for the
previously defined interface.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Add vendor attributes for EHT testbed STA configuration.
This includes enabling STR MLMR mode and forcing power save
on active MLO links for a defined number of beacon periods.
Signed-off-by: Gururaj Pandurangi <quic_panduran@quicinc.com>
Add vendor attributes related to MLO and EMLSR mode
capability configuration for EHT testbed STA. It includes
EHT OM control support and EMLSR padding delay configuration.
Also, generalise the naming of HE OMI control enumeration to
OMI control as it now consists of both HE and EHT OMI control
fields.
Signed-off-by: Gururaj Pandurangi <quic_panduran@quicinc.com>
Add vendor attributes related to MLO and EMLSR mode
capability configuration for EHT DUT. This includes forcing
active MLO links and invoking EMLSR mode entry or exit.
Signed-off-by: Gururaj Pandurangi <quic_panduran@quicinc.com>
Some of the information elements added in IEEE Std 802.11ax-2013 for VHT
purposes have since then been taken into use for other cases and renamed
to remove the "VHT" prefix in the standard. Update the defines for those
elements in the implementation to match the names used in the current
standard.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
IEEE 802.11be enables multiple links between STA and AP. Each of the
link has its own set of statistics. Add additional attributes required
to fetch link layer statistics per MLO link.
For MLO connection, per MLO link statistics will be sent with the new
attribute QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. Also, cumulative
statistics of all the MLO links will be sent outside
QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK to be compatible with legacy user
space.
For non-MLO connection, the statistics will be sent without being nested
inside QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK attribute.
Co-authored-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
The attributes QCA_WLAN_VENDOR_ATTR_LL_STATS_PAD and
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NF_CAL_VAL were allocated the same
attribute number in error. QCA_WLAN_VENDOR_ATTR_LL_STATS_PAD attribute
is known to not be used; thus, it is safe to be renumbered.
Fixes: 1491fc64a8 ("Define QCA vendor per-enum 64-bit pad attributes")
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
When user space triggers a scan, the firmware aborts background scan,
and uses the roam status QCA_ROAM_FAIL_REASON_CURR_AP_STILL_OK instead
of "Invalid roam failures reason".
Signed-off-by: Chunquan Luo <quic_chunquan@quicinc.com>
Define bitmap values used by LL_STATS vendor command
and update the corresponding kernel documentation.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a vendor feature flag for the driver to indicate support for allowed
frequency configuration in AP mode.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add a new vendor command to trigger computation of connected channel
statistics such as channel utilization in STA mode.
Signed-off-by: Ainy Kumari <quic_ainykuma@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Define a new attribute QCA_WLAN_VENDOR_ATTR_CONFIG_AP_ALLOWED_FREQ_LIST
to configure the full list of allowed frequencies for the AP operation.
The configuration is valid only from the next BSS start until the BSS is
stopped. The drivers shall filter out channels on top of this list of
channels based on regulatory or other constraints. This can be used to
specify user's choice of frequencies, allowed list of channels with
static puncturing feature, etc.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Extend QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_WIDTH to configure 320 MHz
bandwidth to the driver/firmware.
Signed-off-by: Ainy Kumari <quic_ainykuma@quicinc.com>
Add preamble puncturing bitmap to the EHT Operation element as per IEEE
P802.11be/D3.0, Figure 9-1002c (EHT Operation Information field format).
Bits set to 1 indicate that the subchannel is punctured, otherwise
active.
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
When writing 64-bit attributes into the netlink buffer, senders may
add a padding attribute to allow the payload of the 64-bit attribute
to be 64-bit aligned. For QCA vendor attributes, currently the
attribute QCA_WLAN_VENDOR_ATTR_PAD in enum qca_wlan_vendor_attr is
defined for this purpose.
Unfortunately, when adding attributes to the netlink buffer, all
attributes at a given level of nesting must be defined in the same
enum so that they can be unambiguously parsed. This means that
QCA_WLAN_VENDOR_ATTR_PAD can only be used to pad 64-bit attributes
defined in enum qca_wlan_vendor_attr.
There are many other QCA vendor enums which define 64-bit attributes,
so add a pad attribute to all of them so that the 64-bit attributes
can be unambiguously padded.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Add a new vendor command and attributes to control and fetch the state
information of the MLO links affiliated with a specific interface.
This will enable user space to dynamically control the MLO links states
based on the latency, throughput and power save requirements.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
An association request in the context of an MLO connection can
contain an ML element that holds the per station profile for
the additional links negotiated. To support this, add a function
to parse the per station profile.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
As a preparation to parse management frames that include ML elements
with per station profiles, split the function to a helper function that
would not memset() the elements structure.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Extend @CONF-OBJ-SEP@ behavior to allow the second entry to be used for
different netRole. In other words, allow both the AP and STA netRole
(though, only a single one per netRole) configuration to be set.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The first call to dpp_configuration_parse_helper() was supposed to use
the separately prepared tmp string with only the first configuration
entry, but it ended up using the full string that included both
configuration entries. This could result in the first configObject
getting a mix of parameters from both entries.
Fix the parsing to use only the text before the @CONF-OBJ-SEP@ separator
for the first entry.
Fixes: 7eb06a3369 ("DPP2: Allow multiple Config Objects to be build on Configurator")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support for WNM event report handling for the BSS color collision
and in use events.
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Yi-Chia Hsieh <yi-chia.hsieh@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Add QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_LOW_LATENCY attribute
to enable/disable Multi-Channel concurrency low latency mode.
The firmware will do optimization of channel time quota for
low latency in Multi-Channel concurrency state if enabled.
Signed-off-by: Liangwei Dong <quic_liangwei@quicinc.com>
During implementation of commit 257b119c2d ("QCA vendor attribute of
update roaming cached statistics info") some deficiencies were noted as
listed below, so fix them. Since these are pre-implementation changes,
no ABI breakage is introduced.
1) Change all RSSI values to be signed values.
2) Add enums for scan type and dwell type instead of documenting
their values with comments
3) Add missing QCA_ROAM_REASON_STA_KICKOUT to enum qca_roam_reason
Signed-off-by: Chunquan Luo <quic_chunquan@quicinc.com>
Add vendor subcmd QCA_NL80211_VENDOR_SUBCMD_ROAM_STATS and attribute id
in enum qca_wlan_vendor_attr_roam_cached_stats for collecting roaming
statistics information when diagnosing roaming behavior.
Signed-off-by: Chunquan Luo <quic_chunquan.quicinc.com>
Add new AP concurrency policy QCA_WLAN_CONCURRENT_AP_POLICY_XR to
configure interface for eXtended Reality (XR) requirements.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Add a new vendor command QCA_NL80211_VENDOR_SUBCMD_GET_MONITOR_MODE to
get the local packet capture status in the monitor mode. Add required
attributes to respond with status of the monitor mode. The monitor mode
can be started/configured by using the
QCA_NL80211_VENDOR_SUBCMD_SET_MONITOR_MODE subcommand.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Add new QCA vendor attributes to configure the driver for EHT
capabilities and multi link configuration.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add new QCA vendor attributes to configure the driver for EHT
capabilities. These attributes are used for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
IEEE P802.11be/D2.0 added a 4-octet Basic EHT-MCS And Nss Set field into
the EHT Operation element. cfg80211 is now verifying that the EHT
Operation element has large enough payload and that check is failing
with the previous version. This commit does not really set the correct
Basic EHT-MCS And Nss Set values, but the IE length check is now passing
to allow initial mac80211_hwsim testing to succeed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Authentication frames include several fixed body parts (see Table 9-68
(Authentication frame body) and Table 9-69 (Presence of fields and
elements in Authentication frames) in IEEE P802.11-REVme/D2.0).
To be able to parse the IE part, these fields need to be skipped. Since
SAE logic already implements this parsing, change SAE authentication
handling functions to return the offset to the IE part. This preparation
is needed for future MLD patches that need to parse out the ML related
elements in the Authentication frames.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Return value of crypto_bignum_to_bin() wasn't always checked, resulting
in potential access to uninitialized values. Fix it, as some analyzers
complain about it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Micha Hashkes <micha.hashkes@intel.com>
Use more specific status code values to report error cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
RSNXE bits were modified, so update the relevant places accordingly.
Please note, WLAN_RSNX_CAPAB_PROT_RANGE_NEG was renamed to
WLAN_RSNX_CAPAB_URNM_MFPR and the bit position is changed to 15 instead
of 10, while BIT 10 is used for WLAN_RSNX_CAPAB_URNM_MFPR_X20 and is not
supported yet.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
