Clear scan results at the beginning of the test case to avoid incorrect
behavior if there are multiple entries for the same BSS. In addition,
use a bit longer wait for receiving an updated Beacon frame in scan
results.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
In the case that the AP MLD is disabled and enabled again, flush
the wpa_supplicant BSS table before reconnecting as otherwise
the previous AP MLD BSSs would be in the BSS table and the wpa_supplicant
would try to connect to them.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The test assumes that STA will try to reconnect with the same SAE group
after the first authentication attempt is rejected due to unsupported
group. Since this behaviour is fixed in the previous patch, configure
two different groups to trigger the second authentication attempt.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
wpa_supplicant will generally never allocate a memory block of that
size. We can therefore assume that it belongs to ASAN and we need to
ignore it.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
The matching code currently only tests whether the prefix of a function
matches. Make this more strict by ensuring that the function name is not
longer.
However, as this breaks some tests (due to inlining), add the ability to
do an explicit prefix match by appending a '*' to the function name. Use
this to change the eap_eke_prf match to eap_eke_prf_* in order to match
one of the actual implementations.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
It seems that sha256_prf may not always be in the stack trace for
failure checking, possibly due to tail call optimization as it simply
calls sha256_prf_bits with updated parameters. Simply match against
sha256_prf_bits directly to avoid issues due to optimizations.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
The wpas_p2p_nfc_handover failure test and the more specific
wps_build_nfc_handover_req_p2p were effectively the same as the matching
currently does a prefix match. The code-path tested in these two cases
only hit a single TEST_FAIL macro in openssl_digest_vector.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
The test here is triggering the allocation failure in the static
wpa_config_parse_password() helper. Use this and decrease the count
instead of matching both wpa_config_set_quoted() and wpa_config_set()
and counting down based on that.
This is in preparation to fix the failure function matching to not do a
prefix match.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
The test expects rsn_pmkid_suite_b_192() to fail but specified only
rsn_pmkid_suite_b without the _192 postfix. Add the postfix so that the
function matching can be fixed later.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Using D-Bus it is possible to request an invalid SD response where
"tlvs" is specified and there is an unknown key (e.g. "bar": "foo"). In
this case, "tlv" is allocated and then never used nor freed. Valgrind
complains as follows:
36 bytes in 1 blocks are definitely lost in loss record 20 of 74
at 0x484C214: calloc (vg_replace_malloc.c:1675)
by 0x41C673: wpabuf_alloc (wpabuf.c:124)
by 0x41C673: wpabuf_alloc_copy (wpabuf.c:162)
by 0x54FB94: wpas_dbus_handler_p2p_service_sd_res (dbus_new_handlers_p2p.c:3016)
by 0x53B9A2: msg_method_handler (dbus_new_helpers.c:356)
by 0x53B9A2: message_handler (dbus_new_helpers.c:412)
by 0x4EAB4B8: dbus_connection_dispatch (in /usr/lib64/libdbus-1.so.3.19.13)
by 0x5495DF: dispatch_data (dbus_common.c:37)
by 0x5495DF: process_watch (dbus_common.c:73)
by 0x5495DF: process_watch_read (dbus_common.c:89)
by 0x41EE8E: eloop_sock_table_dispatch.part.0 (eloop.c:603)
by 0x41FA46: eloop_sock_table_dispatch (eloop.c:597)
by 0x41FA46: eloop_run (eloop.c:1233)
by 0x56A3EE: wpa_supplicant_run (wpa_supplicant.c:8074)
by 0x40DB06: main (main.c:393)
Fix it ensuring that "tlv" is freed both in the error and non-error path
of wpas_dbus_handler_p2p_service_sd_res(). Also, add a test case in
test_dbus.py to verify correct behavior.
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
Using D-Bus it is possible to trigger a valid UPnP SD request where
"tlv" is specified: in this case "tlv" is allocated, and then not used
nor freed. Valgrind complains as follows:
72 bytes in 2 blocks are definitely lost in loss record 46 of 68
at 0x484C214: calloc (vg_replace_malloc.c:1675)
by 0x41C673: wpabuf_alloc (wpabuf.c:124)
by 0x41C673: wpabuf_alloc_copy (wpabuf.c:162)
by 0x54F8B5: wpas_dbus_handler_p2p_service_sd_req (dbus_new_handlers_p2p.c:2928)
by 0x53B9A2: msg_method_handler (dbus_new_helpers.c:356)
by 0x53B9A2: message_handler (dbus_new_helpers.c:412)
by 0x4EAB4B8: dbus_connection_dispatch (in /usr/lib64/libdbus-1.so.3.19.13)
by 0x5495DF: dispatch_data (dbus_common.c:37)
by 0x5495DF: process_watch (dbus_common.c:73)
by 0x5495DF: process_watch_read (dbus_common.c:89)
by 0x41EE8E: eloop_sock_table_dispatch.part.0 (eloop.c:603)
by 0x41FA46: eloop_sock_table_dispatch (eloop.c:597)
by 0x41FA46: eloop_run (eloop.c:1233)
by 0x56A3CE: wpa_supplicant_run (wpa_supplicant.c:8074)
by 0x40DB06: main (main.c:393)
Fix it ensuring that "tlv" is freed, both in the error and non-error
path of wpas_dbus_handler_p2p_service_sd_req(). Also, add a test case in
test_dbus.py to verify correct behavior.
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
Currently color change test is supported only on the first link of the
AP MLD. Extend the support to test on non-first link as well.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Add the eht_mlo_color_change test case to perform color change on the
first link of an AP MLD. Performing on non-first link will be done
later.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Add the he_bss_color_change test case which brings up an HE AP and
performs color change operations and validates the result.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Add a test case 'eht_mld_cohosted_connectivity' which creates two 2 link
AP MLDs and connect a 2 link MLD client to each one of them and test
data traffic.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Add test cases to test basic cohosted MLDs functionality. Add helper
functions to create the configuration file, start hostapd instance.
Client connectivity test case will be added via a subsequent commit.
eht_mld_cohosted_discovery: 2 co-hosted MLDs without non-MLD RNR. Basic
bring up and beacon, MLD RNR, scan validation.
eht_mld_cohosted_discovery_with_rnr: Same like eht_mld_cohosted_discovery
but additionally non-MLD RNR (rnr=1) is also enabled. Validate the non-MLD
RNR as well.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
This is needed to match the implementation change to map the 5 GHz
channels 149-175 to the global operating class 125 instead of 124.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wait for both peers to be connected before checking MESH_LINK_PROBE
behavior. Without this, it was possible for a MESH_LINK_PROBE command to
be issues before the specific peer had been added and that would result
in the nl80211 command failing.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This test case ended up dropping HT capability on channel switch which
is now resulting in mac80211 disconnecting. Avoid this by leaving HT
enabled. In addition, check the P2P Client events explicitly.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When a BSS is removed, the flow continues without actually
waiting for the AP to be stopped. This is racy in flows that
actually expect the AP to be stopped, e.g., test_ap_bss_add_remove().
Try to mitigate such cases by adding a short sleep after the
AP is removed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This is needed to avoid unexpected behavior if a previously executed
test case has left a BSS entry with Interworking emabled into the case.
Signed-off-by: Jouni Malinen <j@w1.fi>
At least some of the previous versions have expired, so need to re-sign
these to avoid EAP test case failures. This contains updates from
running tests/hwsim/auth_server/update.sh.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a test behaving like an Asus RT-AC53 with firmware
3.0.0.4.380_10760-g21a5898, which (in some cases?) can have an ECSA
element stuck in the probe response, when the channel switch is long
finished.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a few tests to validate what happens with connections
while an AP is doing CSA:
- quiet to diff channel (shouldn't connect)
- quiet to same channel (shouldn't connect)
- non-quiet to diff channel (shouldn't connect)
- non-quiet to same channel (should connect)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Verify that the Extended Capabilities element for the TX BSS shows
beacon protection disabled and the Extended Capabilities element for the
non-TX BSS (within the Multiple BSSID element) shows it enabled.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
These can cause unexpected test failures, so dump the pending monitor
socket events more frequently in some cases where event throttling is
seen.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This test could have failed if scan results from a previously executed
test case were still the in the driver cache.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is needed to avoid failures due to previous test cases having left
sae_groups set to something else than the default.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
