Add routines to (de)initialize mesh interface data structures and
join and leave mesh networks.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
For mesh mode to work properly, set supported rates only once.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
This is needed for managing STA entries for mesh use cases.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
sta_info call these to send out the disassoc and deauth frame
which are both not relevent to mesh. So don't send them.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
These key management options were missing from the previous set of
parsed information in scan results.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Abele <jason.abele@gmail.com>
ap_ht40_csa and ap_ht40_csa3 seem to show a cfg80211/mac80211 issue
where a CSA from HT40+ to HT40- channel results in HT getting disabled
due to cfg80211_chandef_compatible() check on c1->width == c2->width
claiming that the new channel is not compatible. For now, comment out
the FAIL case for these known issues to avoid constant failure for cases
that are not wpa_supplicant/hostapd issues. Once the kernel side design
has been reviewed, these error cases can be enabled here.
Signed-off-by: Jouni Malinen <j@w1.fi>
If both HT and VHT was enabled on AP and channel switch event from the
driver indicated that HT was disabled, VHT was left enabled. This
resulted in the following channel configuration failing. Fix this by
disabling VHT if HT gets disabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
Advertise static/dynamic SMPS mode support (according to the wiphy
feature bits) and pass the configured smps_mode when starting the AP.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Add smps_modes field, and let the driver fill it with its supported SMPS
modes (static/dynamic). This will let us start an AP with specific SMPS
mode (e.g., dynamic) that will allow it to reduce its power usage.
Signed-off-by: Eliad Peller <eliad@wizery.com>
The previous TX operation could be on another channel if there are
multiple peers with pending SD queries. To avoid failing to send the
following query, stop the last one to allow any Listen channel to be
used for the following query during p2p_find iteration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 7139cf4a4f ('P2P: Decrement
sd_pending_bcast_queries when sd returns success') added support for
retrying P2P SD queries. However, it did this without limiting how many
retries are allowed. This can result in excessive number of retries if a
peer device does not show up on its Listen channel and there is a
pending SD query to it. Limit the maximum number of SD retries to 100
per p2p_find operation for each peer to avoid unlimited retries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 7139cf4a4f ('P2P: Decrement
sd_pending_bcast_queries when sd returns success') changed P2P SD
behavior in a way that the P2P search loop ended up in continuing with
the first peer entry until it acknowledged receipt of a pending
broadcast SD request while the previous design went through all peers
once. While it is reasonable to retry SD, getting stuck with the first
peer is not really desirable. Change the p2p_continue_find() loop to
continue from the next peer in each iteration to allow progress through
all peers that have pending operations if any other peer is not
acknowledging frames (e.g., due to not being on Listen channel).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces a QCA vendor command and event to provide an
option to use extended versions of the nl80211 connect/roam operations
in a way that allows drivers to offload key management operations to the
driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the not-pre-authorized GO Negotiation case to end up
starting new GO Negotiation before the GO Negotiation Response frame
with status=1 was transmitted. While this works for group formation, it
could reduce test coverage for the common case where that response is
received. At a small sleep to make it less likely for this unexpected
sequence to happen during testing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 1595eb93ae ('P2P: Add support for
60 GHz social channel') had an unintended change to how P2P search scans
2.4 GHz social channels. Use of p2p_supported_freq() to filter the list
of social channels ended up using the disallow_freq setting to remove
social channels from the P2P search scans. This is not desired since
peers need to be found on any of the social channels even if those
channels have been disabled from P2P operating channel use. Restore the
previous behavior by included all the 2.4 GHz social channels in P2P
search scans if the driver indicated support for the 2.4 GHz band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This avoids an issue where a wpa_supplicant build with CONFIG_P2P=y and
CONFIG_HS20=y ended up processing a P2P SD query twice when operating as
a GO and sending out two replies. Only the P2P SD implementation should
reply to P2P SD query in such a case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This reverts commit 851b0c5581.
The kernel now has full support for this (and it is turned off
by default for hwsim) so wpa_supplicant should really go back
to autodetecting this so clients don't have to figure out what
to do.
Also add a debug message stating that P2P_DEVICE support is used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When loading the hwsim module, disable support_p2p_device by default.
This will also become the default in the kernel, but until then it
makes sure it's not turned on by default.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use dynamic radios for P2P_DEVICE tests to be able to test
support when the default in hwsim is to not support it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will be needed to be able to control dynamic mac80211_hwsim
operations like adding and removing a phy. In the past, it has been
possible to start the main programs as root and then use non-root
account for run-tests.py. However, there is already a large number of
cases within the test scripts where sudo is needed. Moving that
requirement to execution of run-tests.py allows those to be simplified
as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows the URL to be passed as a single argument to the program
instead of getting split into multiple by os_exec(). This makes the
operation more robust for cases where the URL could have been received
from an external source and could potentially add extra arguments to the
command line.
In addition, fix the /system/bin/input execution by using system() for
it instead of execv() through os_exec(). /system/bin/input is a script
that execv() won't be able to run. Since the full command line is
specified, system() can be used for this. The keycode is also changed
from 3 to KEYCODE_HOME to make this work with current Android version.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the URL to be passed as a single argument to the program
instead of getting split into multiple by os_exec(). This makes the
operation more robust for cases where the URL could have been received
from an external source and could potentially add extra arguments to the
command line.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the URL to be passed as a single argument to the program
instead of getting split into multiple by os_exec(). This makes the
operation more robust for cases where the URL could have been received
from an external source and could potentially add extra arguments to the
command line.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new "bss_load_update_period" parameter can be used to configure
hostapd to advertise its BSS Load element in Beacon and Probe Response
frames. This parameter is in the units of BUs (Beacon Units).
When enabled, the STA Count and the Channel Utilization value will be
updated periodically in the BSS Load element. The AAC is set to 0 sinze
explicit admission control is not supported. Channel Utilization is
calculated based on the channel survey information from the driver and
as such, requires a driver that supports providing that information for
the current operating channel.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
The new HWSimRadio context manager allows the following
syntax to create (and appropriately destroy) a new radio:
with HWSimRadio([...]) as (radio_id, iface_name):
[...]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For testing P2P-Device support properly, allow dynamically
creating radios with support for it in hwsim.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This moves the addition of P2P Device interface into
wpa_supplicant_add_iface() so that this operation can be done
dynamically when adding an interface to an already running
wpa_supplicant process.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to allow dynamic removal of an interface that adds the
P2P Device interface without leaving behind the management interface
with invalid wpa_s->parent pointer.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of hardcoding reset_devs() to remove wlan5, remove all wlan*
interfaces renaming in the wpa_supplicant process to support the case of
dynamically added hwsim phy.
Signed-off-by: Jouni Malinen <j@w1.fi>
This replaces use of the external hwsim_test tool for most data
connectivity test cases. Only the cases where a special interface
(bridge/VLAN) is used are still executed through hwsim_test.
The internal DATA_TEST_* functionality makes it easier to extend the
connectivity test cases through an external device with real WLAN
hardware instead of the hwsim test setup. In addition, the error reports
from this code can be made more informative.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to use instances of control interfaces in common
code without having to separately address hostapd and wpa_supplicant
behavior differences.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is now possible to run hwsim_test like data connectivity test through
wpa_supplicant/hostapd control interface if CONFIG_TESTING_OPTIONS=y is
used for the build. Test functionality is enabled/disabled at runtime
with "DATA_TEST_CONFIG <1/0>". The "DATA_TEST_TX <dst> <src> <tos>"
command can be used to request a test frame to be transmitted.
"DATA-TEST-RX <dst> <src>" event is generated when the test frame is
received.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to replace data connectivity testing to use
something else than local hwsim_test binary on the controller device.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-hostap: Luciano Coelho <luciano.coelho@intel.com>
Skip CSA tests if the driver doesn't support this in AP mode.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This was forgotten when the key_mgmt parser for SAE and FT-SAE was
added.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
