Verify that advertiser returns 'org.wi-fi.wfds' wildcard in a Probe
Response frame if at least one P2PS advertisement is present.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
This increases testing coverage for VENDOR_ELEM mechanism by explicitly
verifying that the requested element gets added to each of the supported
frame types.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Test P2PS GO and CLI discoverability on group operating channel.
In order to implement these tests, refactor p2ps_connect_p2ps_method
and test_p2ps_connect_adv_go_pin_method to reuse the code for
connection establishment. Also change p2ps_exact_seek so it will
allow getting Probe Response frames from several peers.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
test_p2ps_connect_adv_go_pin_method() expects that
p2ps_provision_keypad_method() returns P2PS-PROV-DONE with details
needed for a connection. However, this event was overridden which
resulted in an incorrect test flow skipping the connection
establishement. The test would pass, however, without really trying to
connect. Fix this by returning the correct event.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
This adds hwsim test ap_vlan_iface_cleanup_multibss. It connects two
stations in different BSS but the same hostapd process. First both
stations are in VLAN 1, then they get reauthenticated into VLAN 2. Due
to the ordering of the stations moving around, this test checks that
bridge and tagged interface referencing counting is done globally, such
that the tagged interface is not removed too early and no bridge is
left over.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
There seem to be cases where flush_scan_cache() was unable to clear all
BSS entries due to a hidden SSID BSS (SSID length 0) showing up again
from cfg80211 BSS table. Check for this and run the flush operation
again if any entries remain.
This fixes an issue where the following hwsim test case sequence
resulted in the last test case failing due to the old BSS entry from the
first test case being in place and showing unexpected flags information:
ap_hs20_min_bandwidth_home_hidden_ssid_in_scan_res
ap_hs20_remediation_required
ap_mixed_security
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These are regression test cases for a segmentation fault issue (use of
freed memory) where interface removal happened while a gas-query item
was pending.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The standard hardcodes the MU Beamformee Capable subfield is hardcoded
to 0 when transmitting by an AP, so there is no need to provide a
configuration parameter for setting this to one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The dev[1] <--> dev[2] data connectivity test was using incorrect
function. dev[2] is also using a P2P group and as such, can have a
different group interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
Group interface name was fetched from the results of an incorrect group
formation and because of this, group removal failed in case P2P Device
is used and dev[1] ends up getting different group ifname for the
groups.
Signed-off-by: Jouni Malinen <j@w1.fi>
The network operations need to use the global control interface to be
performed on the interface that stores the network profiles for
persistent groups.
Signed-off-by: Jouni Malinen <j@w1.fi>
After P2P-GROUP-STARTED event, use group_form_result in order to update
the group_ifname for the device. This is needed when using P2P Device
for managing P2P operations which results in a separate group interface
being used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
In case that there is a need to list the persistent P2P networks,
the global control interface needs to be used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
list_networks() always used the wlanX control interface to query for the
current list of networks. However, when a dedicated P2P Device is used,
the global control interface should be used when checking persistent
group network profiles.
Fix this by adding an optional parameter indicating that the P2P
networks are requested, and in such a case use the global control
interface.
In addition update test_p2p_persistent to use the argument when needed.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
This is required for cases that a dedicated P2P Device interface
is used and then the event will happen on the global interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Send request to set persistent_reconnect on the global control
interface so it would also work when using a dedicated P2P Device
interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
When testing P2P invitation flow, setting the NFC selector
should be done using the global control interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Some tests in test_p2ps.py test a scenario where a separate P2P
group interface is not used. However, this is not a valid case
when a dedicated P2P Device interface is used, as in such a case
a separate group interface must be used.
Handle this by skipping such tests in case a dedicated P2P Device is
used.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Call group_form_result() whenever a new group is started, so that
group_ifname gets updated and later, the group can be removed when
needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When resetting a device, remove all the P2P networks to prevent
unexpected behavior in following tests. This is needed for the case
where P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
This is required for cases where P2P Device is used and the event
happens on the global interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
This is required for cases that multiple interfaces are used and the
event can happen on any of them, for example when a dedicated P2P Device
interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
The tests used p2p_dev_addr that can be different from own_addr,
if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Couple of the EAP-SIM/AKA protocol test cases were leaving out the
Reserved field. This was not intentional since these test cases were
targeting a specific Subtype processing instead of verifying truncated
header case (which is covered separately). Add the Reserved field to
allow the implementation to add an explicit, earlier check for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
Number of the P2P test cases through D-Bus commands were not prepared
for there being a separate group interface when the P2P Device concept
is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Enhance test ap_vlan_wpa2_radius_id_change to change the VLAN-ID
back as a last step. This ensures that the wpa_group for VLAN-ID 1
did not enter FATAL_FAILURE state during the test.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
In addition, this adds some delay between the authentication and data
connectivity test through the newly added VLAN and by doing so, makes
ap_vlan_wpa2_radius_id_change a bit more robust. It was possible for the
EAPOL-Key message 4/4 not having yet been processed by hostapd at the
time the data test started.
Signed-off-by: Jouni Malinen <j@w1.fi>
dynamic_vlan=required also applies to macaddr_acl=2 (RADIUS), especially
when used with WPA-PSK.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The time before trying to associate with an AP that does not advertise
Selected Registrar TRUE is going to be incremented, so increase the
autogo_m2d timeout to avoid reporting incorrect errors due to missing
M2D events.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This change add two new tests to verify hostapd operation when used with
VLANs. Both are based on pmksa_cache_preauth and enable dynamic VLANs,
pmksa_cache_preauth_vlan_used additionally uses a station with VID 1.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
It looks like it was possible to receive an incomplete FAIL line and
break out from test execution due to a parsing error. Handle this more
robustly and log the error.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that there is a kernel patch for IPv6 ProxyARP that is capable of
using the non-AP STAs MAC address as the link layer source address in
NA, validate that behavior rather than the temporary check for BSSID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The 'params' argument was not used at all. Use it as an alternative
means for setting the list of test cases to execute.
Signed-off-by: Jouni Malinen <j@w1.fi>
Explicitly clear cached scan results on the AP interface before starting
ACS. This avoids issues where conflicting BSS entries from previously
executed test cases could affect channel selection.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to filter out test cases that take significantly longer
time to execute (15 seconds or longer). While this reduces testing
coverage, this can be useful to get a pretty quick coverage in
significantly faster time.
Signed-off-by: Jouni Malinen <j@w1.fi>
It's somewhat annoying that you can only run parallel-vm.py as
./parallel-vm.py, not from elsewhere by giving the full path,
so fix that by resolving the paths correctly in the scripts where
needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of hand-writing a (positional) parser, use the argparse module.
This also gets us nice help output.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These test cases need to use the previous-AP-on-correct-band workaround
similarly to test_ap_acs.py test cases for now to work with
mac80211_hwsim limitations on channel survey.
Signed-off-by: Jouni Malinen <j@w1.fi>
Explicitly clear the cfg80211 BSS cache at the beginning of these test
cases to avoid matching BSS flags against incorrect AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looked like cfg80211 BSS entry for the zero-length SSID could remain
after this test case. Stop the AP and scan twice with flush-cache option
to make this less likely to occur and cause issues to following test
cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for this test case to fail if cfg80211 BSS cache
included an entry for the same BSSID on another channel from an earlier
test case. Fix this by epxlicitly flushing the cache. In addition, use
scan_for_bss() to make the test less likely to fail in case of heavy CPU
load.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The way the current channel survey is implemented in mac80211_hwsim
requires for the ACS test cases to be run immediately after the same
radio has been on the expected operating band. This was worked around in
one of the test cases and errors ignored in couple. Extend this
workaround to cover all the test cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like the IP routing table changes used here to trigger
unreachability and following reachability of the server do not work very
well with full IP routing configuration, so run this test case only when
executed under vm-run.sh.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These test cases verify that P2P_FIND and P2P_LISTEN operation continues
after having replied to GO Negotiation Request frame for which we are
not yet ready (i.e., GO Negotiation Response with status=1).
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for this test case to start a new group formation on
dev[1] while the first round was still going through the process of
processing group termination indication. That could result in the second
round failing unexpectedly.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like the 128M default memory size for the hwsim test setup was
not large enough to cover all the needs anymore. Some of the test cases
using tshark could hit OOM with that size. Increase the default
allocation to 192M to avoid this type of issues.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that the packet socket workaround does not get disabled if
EAPOL frames are processed during operation state (i.e., when processing
reauthentication/rekeying on a functional association).
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows multiple dmesg files to be saved if a test case is executed
multiple times similarly to the other logfiles.
Signed-off-by: Jouni Malinen <j@w1.fi>
The kernel had two bugs (one in hwsim and one more important one in
mac80211) in this area, add a test to make sure we can disconnect
without any kernel issues while in powersave.
Also make sure that the TIM bit gets set and cleared again (by checking
with tshark.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It seems to be possible for dev2 (the one with incorrect password) to
stop retries before either dev0 or dev1 reports the authentication
failure event. For now, allow the test case pass if either dev0 or dev1
reports the event rather than requiring both to report this. The
expected behavior can be fine-tuned in the future if the reporting
behavior is modified to be more consistent.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Due to a copy-paste error, these test cases left 4addr mode enabled on
wlan5. This resulted in number of connect_cmd_* test cases failing if
executed after the wpas_in_bridge tests.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant configuration file writing style leaves behind
the temporary file (<filename>.tmp) if renaming fails. Clean that up in
the test case execution.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This test cases used to fail if dev1 had seen dev0 as a GO in an earlier
test case, e.g., when running it after autogo_fail. Fix this by clearing
scan results on dev1 at the beginning of the test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a regression test for an earlier bug that resulted in using
freed memory after a P2P group interface was removed as part of
fallback-to-GO-Negotiation in P2P_CONNECT-auto.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for a low powered CPU to take excessively long time to
delete 1000 network blocks when running under valgrind. This would have
resulted in the test case failing and the following reset operation
timing out which would then stop the test sequence completely.
Signed-off-by: Jouni Malinen <j@w1.fi>
1. Add get_group_ifname() to wpasupplicant.py
2. Use the function to get the interface name for the bridge.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
run-tests.py is running as root, so sudo does not need to be used
anymore from within each test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to use sudo and external rm to remove files now that
run-tests.py is required to run as root.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant configuration writing design (rename instead of
write to original file) did not fail with the symlink-to-self case, so
replace this with the config file being replaced with a directory. In
addition, get rid of unnecessary use of subprocess since run-tests.py is
running as root nowadays.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
1. Modify discovery_stop to use global control interface when calling
P2P_FLUSH.
2. Modify p2p_listen_and_offchannel_tx to use the global control
interface when waiting for P2P PD event.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Some of the tests used p2p_dev_addr() that can be different from
own_addr() if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Some of the tests used p2p_dev_addr() that can be different from
own_addr() if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
The test used p2p_dev_addr() that can be different from own_addr()
if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
The test used p2p_dev_addr() that can be different from own_addr()
if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Fix the destination address that is sent in the WNM-Notification to be
the BSS address opposed to the P2P address.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
This is needed for cases that the group interface differs from the main
interface, i.e., when a dedicated P2P Device interface is used.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When the 'SET' command is used to configure parameters related to P2P
operation use the global control interface and not the per interface one
as otherwise the setting will only have effect on the interface and will
work if a dedicated P2P_DEVICE is used.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Once the connection is established need to call group_form_result() on
the invited device, as otherwise the group interface name is not updated
and the connectivity test is done with the main interface instead of the
group interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
These are far from perfect since timing is quite difficult to match for
the case that behaved incorrectly. Anyway, it looks loke
p2p_service_discovery_peer_not_listening was able to hit the error now
and then, so this should be sufficient as a regression test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Include actual extended listen period in the test and confirm that the
device was available on a social channel during such period by using
non-social operating channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This test case is modifying the list of enabled config_method values and
needs to restore "p2ps" option that is included by default. Without
this, P2PS executed after dbus_get_set_wps could fail.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the GTK-found-in-memory case to be triggered due to
a retransmission of EAPOL-Key msg 3/4 especially when running test cases
under heavy load (i.e., timeout on hostapd due to not receiving the 4/4
response quickly enough). Make this false failure report less likely by
waiting a bit longer after the connection has been completed before
fetching the process memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use another AP instance as a separate bridge port in the proxyarp_open
test cases to increase testing coverage for kernel proxyarp
functionality.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 2e1d7386e2 ('tests: Refactor tshark
running') added a helper function for running tshark. However, it did
not use the filter argument correctly, added an extra -Tfields on the
command line, and failed to use global variable. In practice, this ended
up disabling all the tshark sniffer checks. Fix that by using the filter
argument from the caller and marking the _tshark_filter_arg global.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The hostapd_oom_wpa2_eap test case did not always catch these code
paths, so add a variant of that test case explicitly targeting RADIUS
functions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This ends up using the special User-Name = STA MAC address case for
Accounting-Request. In addition, add Chargeable-User-Identity for one of
the STAs.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the VENDOR-TEST EAP method peer implementation to allow
pending processing case to be selected at run time. The
ap_wpa2_eap_vendor_test test case is similarly extended to include this
option as the second case for full coverage.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends testing coverage of PMF group management cipher suites to
include all the cases supported by the driver (existing BIP =
AES-128-CMAC and the new BIP-GMAC-128, BIP-GMAC-256, BIP-CMAC-256).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Reorder scanning in a way that allows the ER behavior to be more
predictable. The first Probe Request report is for a previously received
frame on the AP and this new sequence avoids leaving either of the PBC
test STAs to be that one.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes testing under very heavy load or under extensive kernel
debugging options more robust by allowing number of test cases to scan
multiple times before giving up on active scans. The main reason for
many of the related test failures is in Probe Response frame from
hostapd not getting out quickly enough especially when multiple BSSes
are operating.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that PBC session overlap detection does not get indicated
when forming the group with the same peer multiple times.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a regression test case for a specific sequence that could result
in wpa_supplicant NULL dereference when a SD request is cancelled before
the SD Request TX status callback has been processed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This set of notes provides information on how virtual guess OS can be
used to run the mac80211_hwsim test cases under any host OS. The
specific example here uses Ubuntu 14.04.1 server as the starting point
and lists the additional packages that need to be installed and commands
that can be used to fetch and build the test programs.
Signed-off-by: Jouni Malinen <j@w1.fi>
There were couple of common cases where the control interface for the
dynamic wpa_supplicant instance could have been left in attached state
until Python ends up cleaning up the instance. This could result in
issues if many monitor interface events were queued for that attached
socket. Make this less likely to cause issues by explicitly detaching
and closing control interfaces before moving to the next test case.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the Action frame used for entring WNM Sleep Mode to
get dropped on the AP side due to it arriving prior to having processed
EAPOL-Key message 4/4 due to a race condition between Data and
Management frame processing paths. Avoid this by waiting for
AP-STA-CONNECTED event from hostapd prior to trying to enter WNM Sleep
Mode. In addition, make the check for the STA flag change more robust by
allowing the wait to be a bit longer with a loop that terminates as soon
as the flag has changed.
Signed-off-by: Jouni Malinen <j@w1.fi>
When the STA is forced to disconnect immediately after completion of
4-way handshake, there is a race condition on the AP side between the
reception of EAPOL-Key msg 4/4 and the following Deauthentication frame.
It is possible for the deauthentication notification to be processed
first since that message uses different path from kernel to user space.
If hostapd does not receive EAPOL-Key msg 4/4 prior to deauthentication,
no PMKSA cache entry is added. This race condition was making the test
cases expecting PMKSA caching to work to fail every now and then. Avoid
this issue by waiting for AP-STA-CONNECTED event from hostapd. This
makes sure the PMKSA cache entry gets added on the AP side.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like this test case is failing every now and then, so add some
more time for the olbc_ht value to get updated before reporting a
failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like the gobject module does not get installed by default for
Python at least on Ubuntu server, so modify the D-Bus test case files to
import this in a way that allows other test cases to be run even without
gobject module being installed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case uses get_bss() with a BSSID to find a BSS entry. That can
result in failures if there are multiple BSS entries in wpa_supplicant
BSS table for the same BSSID, e.g., due to an earlier hidden SSID test
case. Explicitly clear the cfg80211 and wpa_supplicant scan caches at
the beginning of this test case to make it less likely for earlier test
cases to trigger a failure here.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case uses get_bss() with a BSSID to find a BSS entry. That can
result in failures if there are multiple BSS entries in wpa_supplicant
BSS table for the same BSSID, e.g., due to an earlier hidden SSID test
case. Explicitly clear the cfg80211 and wpa_supplicant scan caches at
the beginning of this test case to make it less likely for earlier test
cases to trigger a failure here.
Signed-off-by: Jouni Malinen <j@w1.fi>
This step requires kernel changes that are not yet in upstream Linux
tree, so mark this as skip rather than failure for now.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use SELECT_NETWORK instead of REASSOCIATE for the first reconnection to
avoid unnecessary long wait for temporary network disabling to be
cleared. In addition, wait for the disconnect event after issuing the
DISCONNECT commands to avoid issues due to any pending events during the
immediately following reconnection attempt.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to figure out what happened if the test case fails
due to not finding all the needed OSU-PROVIDER information.
Signed-off-by: Jouni Malinen <j@w1.fi>
The external cfg80211 scan flushing operation requires a relatively
recent iw version and not all distributions include that. Avoid false
failure reports by marking these test cases skipped if the iw command
fails.
Signed-off-by: Jouni Malinen <j@w1.fi>
Due to a typo and missing hapd variable initialization, some of the DFS
and VHT test cases were marked as failures even though they were
supposed to be marked as skipped in case the kernel and wireless-regdb
did not have sufficient support for these modes.
Signed-off-by: Jouni Malinen <j@w1.fi>
If dbus_probe_req_reporting was run before dbus_probe_req_reporting_oom,
the SubscribeProbeReq() method succeeded since the memory allocation
that was supposed to fail in the OOM test case was not even tried.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a regression test case to detect a failure that resulted in an
up to five second busy loop through wpa_supplicant_fast_associate() when
interworking_find_network_match() and wpa_supplicant_select_bss() get
different matching results.
Signed-off-by: Jouni Malinen <j@w1.fi>
If Calling-Station-Id matches, but CUI does not, NAS is expected to
reject the request instead of accepting it. Verify that Disconnect-NAK
is returned for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that wpa_supplicant reconnects if PMF is enabled,
unprotected Deauthentication/Disassociation frame is received, and the
AP does not reply to SA Query.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that Certification signals include the expected
information on peer certificates and that dNSName constraint can be
configured based on that and is working both in matching and not
matching cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case was verifying that the first unused VENDOR_ELEM value
above the current maximum is rejected. That makes it a bit inconvenient
to add new entries, so increase the elem value to leave room for new
additions without having to continuously modify this test case.
Signed-off-by: Jouni Malinen <j@w1.fi>
This increases testing coverage for OCSP processing by confirming that
valid OCSP response showing revoked certificate status prevents
successful handshake completion. In addition, unknown certificate status
is verified to prevent connection if OCSP is required and allow
connection if OCSP is optional.
Signed-off-by: Jouni Malinen <j@w1.fi>
GnuTLS has a hardcoded three day limit on OCSP response age regardless
of the next update value in the response. To make this work in the test
scripts, try to generate a new response when starting the authentication
server. The old mechanism of a response without next update value is
used as a backup option if openssl is not available or fails to generate
the response for some reason.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is more robust than checking the driver capability because it is
also possible for the wpa_supplicant build to be configured without mesh
support regardless of whether the driver supports it.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it more convenient to run tests with wpa_supplicant builds
that do not support SAE (e.g., due to crypto library not providing
sufficient functionality for this).
Signed-off-by: Jouni Malinen <j@w1.fi>
This format as a DER encoded blob is supported by both OpenSSL and
GnuTLS while the previous OpenSSL specific format did not get accepted
by GnuTLS.
Signed-off-by: Jouni Malinen <j@w1.fi>
With GnuTLS, domain_suffix_match is currently requiring full match, so
split the test cases in a way that can be reported more cleanly as PASS
or SKIP based on TLS library behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Proper configuration should be used here to get server validation
enabled, so update the test cases to provide the ca_cert parameter. This
was included in number of existing test cases, but not all.
Signed-off-by: Jouni Malinen <j@w1.fi>
These parameters are supported only with OpenSSL, so split any test case
that used those for a successful connection into two test cases. Skip
all test cases where these are used without the selected TLS library
supporting them to avoid reporting failures incorrectly. Though, verify
that subject_match and altsubject_match get rejected properly if TLS
library does not support these.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check wpa_supplicant EAP capability and skip EAP-pwd and EAP-FAST test
cases if the build did not include support for these. This is cleaner
than reporting failures for such test cases when the selected TLS
library does not support the EAP method.
Signed-off-by: Jouni Malinen <j@w1.fi>
This network profile parameter will be removed with the cleanup that
makes mesh use shared functions for setting channel parameters. That
will allow HT to be enabled automatically based on driver capabilities.
Signed-off-by: Jouni Malinen <j@w1.fi>
Refactor the code to run tshark into its own submodule. This allows
even remembering whether -Y or -R needs to be used for filtering.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These test cases run hostapd interface setup multiple times with
TEST_ALLOC_FAIL commands triggering memory allocation failures one by
one at each possible location in the setup sequence. Effectively, these
test cases will hit most error paths for memory allocation issue cases
(i.e., only the cases requiring more than one allocation failure in a
sequence are not covered).
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of returning "skip" from the test function, raise the new
HwsimSkip exception to indicate a test case was skipped.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is a race condition between wlantest having received and written
the sniffer log and this test case using tshark to process it. Wait one
second before running tshark to make it less likely to get truncated
results that can result in the test case failing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify error cases in bgscan module parameters. Increase learn bgscan
module coverage with parsing of the saved data and probe frequency
selection.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify correct behavior with invalid commands. In addition, allow minor
mac80211_hwsim modifications to be used to enable testing of the driver
interface to enable and disable channel switching.
Signed-off-by: Jouni Malinen <j@w1.fi>
Make sure the wmm_ac_status command reflects correctly the existing
tspecs after add_ts/del_ts commands. Add a new test to verify all tspecs
are removed on roaming (while FT is not used).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
The previous version was enabling all three stations at the same time
and left dev[1] and dev[2] competing on getting connected with dev[0]
that allowed only one pairing. This was not exactly robust and the pass
criteria depended on an extra event from either dev[1] or dev[2]. Fix
that by first connecting dev[0] and dev[1] and only after that, start
dev[2]. This allows proper validation of both the peering limit on
dev[0] and no extra event on dev[2].
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for the Probe Response frame wait to time out when active
scanning is used under heavy CPU load. Make this test case more robust
by trying multiple times before declaring the scan for a hidden SSID to
have failed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows automated testing of the wpa_supplicant D-Bus interface. The
instance controlling wlan0 registers with D-Bus if dbus-daemon was
started successfully. This is only used in VM testing, i.e., not when
run-tests.sh is used on the host system with D-Bus running for normal
system purposes.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_cli and hostapd_cli are not currently tested for code coverage, so
filter the files specific to those components away from the code
coverage reports. *_module_tests.c are not included in normal builds, so
drop them as well. In addition, drop the system header file (byteswap.h)
that gets somehow unnecessarily included in the reports for couple of
lines.
Signed-off-by: Jouni Malinen <j@w1.fi>
This leaves the build tree with valid wpa_supplicant object files in the
end and makes it a bit easier to do additional custom builds when
needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, these test cases were marked as failures, but it is nicer to
mark as skipped if the kernel does not include support for mesh.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some of the newer dfs_radar* test cases did not allow hostapd
startup to fail. Since these require relatively recent kernel
support, mark the test cases with skip rather than fail based
on that step failing.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_ht_smps needs relatively recern kernel support, so allow it to be
skipped rather than claimed as failure, in case hostapd startup fails.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the separate builds to not include
wpa_cli/hostapd_cli in the default location. Make sure hostapd_cli gets
built for --codecov cases and update both WPACLI and HAPDCLI paths to
match the alternative location.
Signed-off-by: Jouni Malinen <j@w1.fi>
Large number of test cases will fail if hostapd fails to start as the
RADIUS server. To make this more obvious, verify that the RADIUS server
instance is running and do not even start test execution if the setup if
not work properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the scr.addstr() operations to fail and terminate
parallel-vm.py if the number of failed test cases increased beyond what
fits on the screen.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait for a CTRL-EVENT-REGDOM-CHANGE even before returning from
set_country() to avoid issues with test operations being executed before
all components have had chance to update their regulatory domain
information. Some of these test cases could fail under heavy load.
Signed-off-by: Jouni Malinen <j@w1.fi>
Merge partial lines together before processing them in parallel-vm.py.
This avoids issues in cases where the stdout read gets split into pieces
that do not include the full READY/PASS/FAIL/SKIP information. In
addition, strip unnecessary whitespace (mainly, '\r') from the log
lines.
Signed-off-by: Jouni Malinen <j@w1.fi>
parallel-vm.log is now written with details of test execution steps and
results. This makes it easier to debug if something goes wrong in VM
monitoring. The --debug option can be used to enable verbose debugging.
Signed-off-by: Jouni Malinen <j@w1.fi>
parallel-vm.py is now retrying failed cases once at the end of the run.
If all the failed test cases passed on the second attempt, that is noted
in the summary output. Results are also indicated as the exit value from
the run: 0 = all cases passed on first run, 1 = some cases failed once,
but everything passed after one retry, 2 = some cases failed did not
succeed at all.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds the remaining test cases that took more than 15 seconds to run
into the list of test cases to run at the beginning of the execution to
avoid these being left at the end when only some of the VMs may be
running.
Signed-off-by: Jouni Malinen <j@w1.fi>
Avoid unnecessary DATA_TEST_CONFIG calls and wlantest_cli invocations to
speed up the test cases. This drops ap_qosmap execution time from about
14 seconds to under 3 seconds.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to wait for the longer fixed duration for each STA when
an event message or an earlier wait for another STA can be used instead.
Signed-off-by: Jouni Malinen <j@w1.fi>
Clear cfg80211 BSS table more carefully after the scan_hidden* test
cases. At least scan_hidden_many could have left behind a hidden SSID
entry that could cause problems for following scan_bss_operations test
case.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the initial Authentication frame was too early for the peer (i.e.,
NEW_PEER_CANDIDATE event arrived only after the Authentication frame),
wpas_mesh_open_no_auto and wpas_mesh_secure_no_auto test cases were
failing since they waited only for 10 seconds for the connection to be
completed while the retry timer was set to 10-20 seconds on the
authenticator side.
Signed-off-by: Jouni Malinen <j@w1.fi>
The kernel commit 'packet: make packet_snd fail on len smaller than l2
header' started rejecting <= 14 octet raw packet socket transmission.
This test case was testing with 14 ocets and that is now rejected by the
kernel. While this may be a kernel side issue, use one octet longer test
data for now to avoid undesired FAIL cases in hwsim tests.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous design did not actually break from the wait loop when the
AP changed back to 40 MHz channel and as such, ended up waiting the full
30 second time. Furthermore, the five second delay time for returning
back to 40 MHz was not sufficiently long to test behavior correctly
since the STA did not have any chances of returning the next coex report
before the AP had returned to 40 MHz. Increase the AP wait time to 15
seconds so that the once per 10 seconds OBSS scan from the STA gets in
before changing back to 40 MHz channel (after the 40 MHz intolerant AP
gets disabled).
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a single iteration through the module dictionary rather than
iterating over the keys and separately fetching values to get the
function.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to wait for one extra second to chown log files when
running as root which is always the case in VM execution.
Signed-off-by: Jouni Malinen <j@w1.fi>
These test cases had a long 120 seconds wait for the GO Negotiation
initiator to time out. This can be done using two devices in parallel to
save two minutes from total test execution time.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function did not seem to do anything else apart from making it less
obvious that hwsim_utils.test_connectivity() is called.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait one second between each kvm start to avoid hitting large number of
processes trying to start in parallel. This allows the VMs to be started
more efficiently for parallel-vm.py runs with large number of VMs.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the hidden SSID entry to leak into following test
cases and result in failures, e.g., in this sequence:
scan_hidden
scan_reqs_with_non_scan_radio_work
radius_auth_unreachable
wep_open_auth
BSS <BSSID> picked incorrect BSS entry within wpa_supplicant due to the
old zero-length SSID showing up from the earlier hidden SSID case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Move test cases with long duration to the beginning as an optimization
to avoid last part of the test execution running a long duration test
case on a single VM while all other VMs have already completed their
work.
Signed-off-by: Jouni Malinen <j@w1.fi>
Now there is only one set of commands to maintain. The separate reports
for individual components have not been of much use in the past, so they
are dropped for now.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to wait for the timeout if the ROAM command itself
failed. This could happen if an earlier test case had left hidden SSIDs
in the cfg80211 BSS table.
Signed-off-by: Jouni Malinen <j@w1.fi>
Leaving hidden SSIDs in the cfg80211 BSS table can result in errors in
the following test cases, so use special care to clear all BSS entries
at the end of the wext_hidden test case.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows code coverage report to be generated must faster with the
help of parallel VMs executing test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that offchannel TX (PD in this specific case) does not
stop ongoing long P2P_LISTEN operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There were couple of typos in the IP addresses and there was no coverage
for the normal unicast ARP response from the bridge (since non-wireless
device does not get proxied by the AP). In addition, it is better to
change the IP address used here to be unique to make the sniffer logs
easier to interpret.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds transmission of number of NS/NA frames to test ProxyARP
behavior. The actual validation of the AP behavior is still manual,
i.e., a separate inspectation of the capture files is needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This may be needed in some corner cases where broadcast frames with two
associated stations are received by both devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The final invitation case in this test was verified incorrectly. The GO
was already operatign in that case, so there was not supposed to be a
new P2P-GROUP-STARTED message from GO. That happened to be show up in
the pending event messages from the last instance, but that was just by
accident and any additional dump_monitor() operation added here would
cause this test to fail. Fix this by handling the final invitation
separately and verifying that only the client side indicates
P2P-GROUP-STARTED.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for WpaSupplicant instance to be used without the global
control socket, so allow dump_monitor() to handle this case cleanly.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for regulatory domain changes to "leak" into following
test cases in number of cases where the cfg80211 BSS table remained
after regulatory domain had been restored to world roaming. Try to make
this less likely to occur by explicitly clearing BSS table at the end of
test cases that use different regulatory domain. This makes P2P test
cases that verify channel selection based on world roaming rules more
robust.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for BSS entries on the scanned channel (2412 MHz) to be
left behind after flush_scan_cache() call. Use a less likely channel
2417 MHz as the default channel to scan. This will hopefully get rid of
most problematic BSS entries from previous test cases. For example,
ap_hs20_oen followed by ap_hs20_random_mac could fail due to
INTERWORKING_CONNECT seeing non-RSN scan result from the previous test
case.
Signed-off-by: Jouni Malinen <j@w1.fi>
This ends up using the special offchannel.c code path where a different
interface is selected for TX. In addition, the P2P-PRESENCE-RESPONSE
event is verified to be delivered on the group interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
The results for these are not currently verified, but this allows
--codecov runs to get more coverage for the command line argument
parsers.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids one more cleanup step between most test cases by clearing
the default PMF behavior change only in case it was actually modified
during a test.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids one more cleanup step between most test cases by stopping ER
only in case it was actually used during a test.
Signed-off-by: Jouni Malinen <j@w1.fi>
This uses a new testing mode in hostapd to allow RRM neighbor request
transmittion to be tested. For the second part of the test case to be
executed, mac80211_hwsim needs to be modified to claim support for the
required RRM capabilities (that change is not yet in Linux kernel).
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies processing of various ARP messages at an AP that enables
ProxyARP. All the validation steps have not yet been scripted, i.e., the
sniffer traces need manual analysis for full coverage.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This provides a regression test that would have caught the recent
issue with tls_openssl.c change breaking EAP-FAST.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that the corner case of a duplicated, retransmitted
Invitation Response frame ends up being dropped instead of being
processed twice for the case of Invitation Request getting resend with
social channel as an operating channel in case of no common channels
found.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds P2P_SERV_DISC_REQ, P2P_SERVICE_ADD, and P2P_SERVICE_DEL error
cases and P2P_SERVICE_FLUSH and P2P_SERC_DISC_EXTERNAL testing.
Signed-off-by: Jouni Malinen <j@w1.fi>
A single channel scan just before WPS_REG, WPS_PBC, and WPS_PIN commands
can be used to avoid having to run a full scan. This saves significant
amount of time in the WPS test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This increases wpa_supplicant_ie_txt(), print_bss_info(), and
wpa_supplicant_ctrl_iface_scan_result() testing coverage to include the
previously missing key management options.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that IBSS_RSN <peer> return OK for the case where a valid
and already connection peer address is given.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to pass the test case names to the VMs when using
parallel-vm.py. Removing those from the command line helps in avoiding
kernel panic if maximum number of kernel parameters limit is hit.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use single channel scan instead of full scan to save time. In addition,
use EAP-GPSK which takes significantly less CPU that EAP-EKE with
default parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
