wpa_supplicant does not configure BIGTK(s) to the driver when the STA
reconnects to the same AP after disconnect due to not clearing the last
configured BIGTK values during disconnect. To avoid such issues clear
the BIGTK values while clearing PTK and other group keys.
Fixes: 2d4c78aef7 ("Configure received BIGTK on station/supplicant side")
Fixes: f15cc834cb ("MLD STA: Processing of EAPOL-Key msg 3/4 frame when using MLO")
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
The ap_mld_addr entry was added without introducing a new mask bit which
does not follow the expected style for adding new information into the
BSS command and might result in unexpected behavior for external
components. Define a new BSS command information mask bit for this AP
MLD address and print the AP MLD address in the BSS info only if the
mask bit is set.
Fixes: db99e7341a ("Add AP MLD address into BSS command output")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a vendor attribute for an EHT DUT to configure the type of TID-To-Link
Mapping Negotiation Support for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a QCA vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_AMPDU_CNT to
enable configuration of TX maximum aggregate size with a specific peer.
This can be used to improve performance in noisy environment. In AP
mode, the peer MAC address of the associated STA is specified with
QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_MAC.
Signed-off-by: Will Huang <quic_wilhuang@quicinc.com>
Rename the attribute QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC
to a generic name QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_MAC, so other
configuration commands can reuse it. And make backward compatibility of
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC, define it as same
value of QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_MAC (35).
Signed-off-by: Will Huang <quic_wilhuang@quicinc.com>
The driver might decide to change the operating band on its own, e.g.,
when trying to use a single channel in AP + AP case. A CSA event will be
notified to hostapd to update the channel/frequency, but hw_mode did not
get updated accordingly.
This may cause hostapd interface restarting to fail, e.g., with control
interface DISABLE / ENABLE commands at configured_fixed_chan_to_freq(),
because of the mismatch between conf->channel and conf->hw_mode.
Update hw_mode right after channel change to fix this.
Signed-off-by: ngong <quic_ngong@quicinc.com>
Per IEEE P802.11be/D4.0, 9.4.2.316 (QoS Characteristics element), enable
support for the following optional QoS Characteristics parameters:
- Maximum MSDU Size
- Service Start Time
- Service Start Time LinkID
- Mean Data Rate
- Delayed Bounded Burst Size
- MSDU Lifetime
- MSDU Delivery Info
- Medium Time
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Add support to configure the mandatory QoS Characteristics parameters
per IEEE P802.11be/D4.0, 9.4.2.316 (QoS Characteristics element), in SCS
request:
- Minimum Service Interval
- Maximum Service Interval
- Minimum Data Rate
- Delay Bound
Enable STA SCS traffic descriptor support for EHT connection when the
connected EHT AP advertises SCS traffic descriptor capability in the EHT
Capabilities element.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Set WFA capability to allow non-EHT SCS Traffic support in association
elements when the AP advertises support for non-EHT SCS Traffic support
via Beacon or Probe Response frame. This capability is upper layer
functionality and as such, does not need a separate driver capability
indication or configuration, but indicate this only if the AP supports
the feature to minimize risk of interoperability issues with a new
information element.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Add a vendor attribute for EHT testbed STA to configure MLD ID in the ML
Probe Request frame transmitted as part of host initiated scan request.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Get rid of the warning about unrecognized Fragment element when FTE is
fragmented and make the total length of the FTE itself and the following
Fragment elements available. For now, use a separate variable for the
total length to avoid confusing existing callers.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The FTE parser itself used valid data, but the reassembled buffer was
available only during the parser run. That buffer will be needed for the
caller as well since most of the parsed data is used as pointers instead
of copied data.
Store the reassembled buffer in struct wpa_ft_ies and require
wpa_ft_parse_ies() callers to use wpa_ft_parse_ies_free() to free any
possibly allocated temporary data after wpa_ft_parse_ies() calls that
return success (0).
Fixes: 43b5f11d96 ("Defragmentation of FTE")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This replaces the earlier commit 4c079dcc64 ("Increment
hmac_sha*_vector() maximum num_elem value to 25") with a smaller
increment of just one extra element since the updated FTE MIC
calculation design does not use separate elements. This reduces stack
memory need. In addition, this starts using a define value for the
maximum number of vector elements to make this easier to change and to
make the code more readable.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Generate the "extra" data buffer outside wpa_ft_mic() to make this
function easier to share for MLO FT Reassociation Response frame. This
replaces the earlier design in commit e6f64a8e1d ("FT: FTE MIC
calculation for MLO Reassociation Request frame").
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend wpa_ft_mic() to take in an array of link addresses to allow the
FTE MIC to be calculated for Reassociation Request frame as described in
IEEE P802.11be/D4.0, 13.8.4. This commit does not change actual
behavior, i.e., this is just preparing wpa_ft_mic() and the existing
callers with a new argument.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is needed for FTE MIC calculation for Reassociation Request frmae
when using MLO which could add 15 link addresses into the input data.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new QCA vendor sub command QCA_NL80211_VENDOR_SUBCMD_TX_LATENCY to
configure, retrieve, and report per-link transmit latency statistics.
When used as a command, userspace configures transmit latency monitoring
and get the corresponding statistics of the last period. When used as a
command response, driver replies the get action from userspace with the
statistics of the last period. When used as an event, driver reports the
statistics periodically.
Signed-off-by: Yu Wang <quic_yyuwang@quicinc.com>
When a CHANNEL_LIST_CHANGED event is received, memory of
iface->hw_features is freed and allocated again with
hostapd_get_hw_features(), but iface->current_mode still refer to the
original memory address, which is not correct since that memory has been
freed. This could happen in cases where the driver provides channel list
updates during the lifetime of the started BSS.
Fix this by updated iface->current_mode to point to the new array of hw
features.
Fixes: 0837863fbc ("AP: Handle 6 GHz AP state machine with NO_IR flags")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Typecasting takes precedence over division here, so the legacy rates
larger than 255 * 100 kbps (i.e., 36, 48, 54 Mbps) ended up getting
truncated to invalid values.
Fix this by typecasting the value after the division.
Fixes: d4f3003c56 ("nl80211: Configure Beacon frame TX rate if driver advertises support")
Signed-off-by: Prasanna JS <quic_pjs@quicinc.com>
interfaces.iface[i] might be NULL when going through the cleanup of all
remaining interfaces at the end of the process termination. The changes
for clearing drv_priv in AP MLD cause that cleanup process to crash on
dereferencing a NULL pointer.
Fix this by explicitly checking that the interface context is available
before trying to clear the pointer to driver data.
Fixes: 7fa99b3246 ("AP: Allow starting multiple interfaces within single MLD")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Define an attribute for high RSSI roam trigger threshold. STA is
expected to trigger roam if the current connected AP's RSSI gets above
this high RSSI threshold. STA's roam attempt on high RSSI threshold aims
to find candidates from other better Wi-Fi bands.
Signed-off-by: Sunil Dutt <quic_usdutt@quicinc.com>
Add three vendor roam control attributes to configure the roaming
parameters dynamically.
QCA_ATTR_ROAM_CONTROL_CONNECTED_LOW_RSSI_THRESHOLD controls the
connected AP's low RSSI threshold to trigger the neighbor lookup.
QCA_ATTR_ROAM_CONTROL_CANDIDATE_ROAM_RSSI_DIFF and
QCA_ATTR_ROAM_CONTROL_6GHZ_CANDIDATE_ROAM_RSSI_DIFF control the RSSI
difference threshold between the connected AP and the new candidate AP
for the roam to trigger.
Co-authored-by: Sunil Dutt <quic_usdutt@quicinc.com>
Signed-off-by: Sunil Dutt <quic_usdutt@quicinc.com>
Extend enum qca_wlan_vendor_attr_mlo_peer_prim_netdev_event to add MLD
MAC address, the number of links, and link info. Link info contains
ifindex and MAC address of each link of a non-AP MLD that was negotiated
in ML association.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add vendor attribute IDs QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ORIGINAL_BSSID,
QCA_WLAN_VENDOR_ATTR_ROAM_STATS_CANDIDATE_BSSID, and
QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ROAMED_BSSID for updating roaming AP
BSSID to user space to enable user space collecting the BSSID for
roaming issues.
Signed-off-by: Chunquan Luo <quic_chunquan@quicinc.com>
Add support to obtain the start channel when checking whether DFS
is required when using 320 MHz channels.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Determine the channel width by operating class for the 6 GHz band when
validating puncturing bitmap. This is needed to allow puncturing to be
used with 320 MHz channels.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add mld_addr configuration option to set the MLD MAC address.
The already existing bssid configuration option can be used to
control the AP MLD's link addresses.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
When STAs connect to transmitted BSS and nontransmitted BSS, the
AP should assign the aIDs from the same pool.
Use the transmitted BSS AID pool to assign AIDs when the AP enables
multiple BSSID.
Signed-off-by: Allen.Ye <allen.ye@mediatek.com>
Pass bss->ctx instead of drv->ctx in order to avoid multiple reports for
the first bss. The first report would otherwise clear hapd->cca_color and
subsequent reports would cause the iface bss color to be set to 0.
In order to avoid any issues with cancellations, only overwrite the color
based on hapd->cca_color if it was actually set.
Fixes: 33c4dd26cd ("BSS coloring: Handle the collision and CCA events coming from the kernel")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A copy-paste issue in wpa_ft_bigtk_subelem() ended up encoding the IGTK
value instead of the BIGTK when providing the current BIGTK to the STA
during FT protocol. Fix this to use the correct key to avoid issues when
beacon protection is used with FT.
Fixes: 16889aff40 ("Add BIGTK KDE and subelement similarly to IGTK")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
QCA vendor extension is used for NDP setup. This defines the new
attributes QCA_WLAN_VENDOR_ATTR_NDP_CSIA_CAPABILITIES and
QCA_WLAN_VENDOR_ATTR_NDP_GTK_REQUIRED to support GTKSA, IGTKSA, and
BIGTKSA for NDP setup.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The set of protected elements in the FTE in Reassociation Response frame
is different for MLO. Count RSNE and RSNXE separately for each link.
This implementation uses the number of links for which a GTK was
provided which does not fully match the standard ("requested link") and
a more accurate implementation is likely needed, but that will require
some more complexity and state information.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Defragment the FTE if it was fragmented. This is needed for MLO when the
FTE in Reassociation Response frame might be longer than 255 octets to
include all the group keys for all the links.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Parse link id and station MLD address received from the driver in the
NL80211_CMD_NEW_STA event.
Set MLO information of the station to the sta_info and wpa_sm.
Co-authored-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add check to skip the STA mode specific MLO link channel switch handling
in AP mode. Commit 1b6f3b5850 ("MLD STA: Indicate per link channel
switch") added this indication only for STA mode.
Signed-off-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
Add support to parse association link id and MLD address from the
NL80211_CMD_UPDATE_OWE_INFO event.
Set MLO information of the station to the sta_info and wpa_sm.
Use station association link address for sending DH IE info to the
driver.
Signed-off-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
Use station association link address for sending SAE authentication
status to the driver in AP mode external authentication status.
Signed-off-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
Extend QCA_WLAN_VENDOR_ATTR_CONFIG_OPTIMIZED_POWER_MANAGEMENT
attribute to support enum qca_wlan_vendor_opm_mode.
Add QCA vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_ITO and
QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_SPEC_WAKE to configure inactivity
timeout and speculative wake interval in User defined optimized
power save mode.
Signed-off-by: Vishal Miskin <quic_vmiskin@quicinc.com>
Verify that the operation succeeds before a debug print indicating that
it did. This was already done in most callers, so be more consistent and
do it here as well.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The second argument to memset() is only eight bits, so there is no point
in trying to set 0xffff values for an array of 16-bit fields. 0xff will
do the exact same thing without causing static analyzes warnings about
truncated value.
Fixes: 903e3a1e62 ("FILS: Fix maximum NSS calculation for FD frame")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
ideal_chan is NULL here, so it is not really valid to try to debug print
something from it due to the implied NULL pointer dereferencing.
Fixes: af0f60e7dd ("EHT: Calculate puncturing bitmap for ACS")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Check the ieee802_11_parse_elems() return code and do not proceed in
various cases if parsing failed. Previously, these cases would have been
allowed to continue by ignoring whatever might have followed in the IE
buffer after the first detected parsing failure. This is not really an
issue in practice, but it feels cleaner to explicitly stop when
receiving an invalid set of IEs.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Optimize the search for nonzero octets when checking for the need to
work around WPS M1 padding. The previous implementation was really
inefficient (O(n^2)) and while that was likely sufficiently fast for the
cases where the MMPDU size limit prevents long buffers (e.g., all P2P
Action frames), it might be able to take tens of seconds on low-end CPUs
with maximum length EAP-WSC messages during WPS provisioning. More
visibly, this was causing OSS-Fuzz to time out a test case with
unrealisticly long data (i.e., almost 10 times the maximum EAP-WSC
buffer length).
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=60039
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow the phase2_auth=2 parameter (in phase1 configuration item) to be
used with EAP-TTLS to require Phase 2 authentication. In practice, this
disables TLS session resumption since EAP-TTLS is defined to skip Phase
2 when resuming a session.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The previous PEAP client behavior allowed the server to skip Phase 2
authentication with the expectation that the server was authenticated
during Phase 1 through TLS server certificate validation. Various PEAP
specifications are not exactly clear on what the behavior on this front
is supposed to be and as such, this ended up being more flexible than
the TTLS/FAST/TEAP cases. However, this is not really ideal when
unfortunately common misconfiguration of PEAP is used in deployed
devices where the server trust root (ca_cert) is not configured or the
user has an easy option for allowing this validation step to be skipped.
Change the default PEAP client behavior to be to require Phase 2
authentication to be successfully completed for cases where TLS session
resumption is not used and the client certificate has not been
configured. Those two exceptions are the main cases where a deployed
authentication server might skip Phase 2 and as such, where a more
strict default behavior could result in undesired interoperability
issues. Requiring Phase 2 authentication will end up disabling TLS
session resumption automatically to avoid interoperability issues.
Allow Phase 2 authentication behavior to be configured with a new phase1
configuration parameter option:
'phase2_auth' option can be used to control Phase 2 (i.e., within TLS
tunnel) behavior for PEAP:
* 0 = do not require Phase 2 authentication
* 1 = require Phase 2 authentication when client certificate
(private_key/client_cert) is no used and TLS session resumption was
not used (default)
* 2 = require Phase 2 authentication in all cases
Signed-off-by: Jouni Malinen <j@w1.fi>
Update documentation of the QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_WIDTH
and QCA_WLAN_VENDOR_ATTR_CONFIG_CHAN_WIDTH_UPDATE_TYPE attributes to
indicate support for per-MLO link configuration.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support for per-MLO link configurations in
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION commands.
Additionally, add documentation for
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION commands.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Define a new QCA vendor test config attribute to configure powersave
on MLO links.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend bitwise mask in enum qca_wlan_tdls_caps_features_supported to get
the TDLS wider bandwidth capability from the driver.
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
Retrieve the puncturing bitmap sent by the driver in channel select
events for ACS when using the QCA vendor specific event.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Previously, NL_STOP was returned from the survey dump handler if the
maximum number of frequencies was reached for storing survey
information, but this is causing wpa_supplicant context getting stuck if
the current SKB returned by the kernel itself ends with NLMSG_DONE type
message. This is due to libnl immediately stopping processing the
current SKB upon receiving NL_STOP and not being able to process
NLMSG_DONE type message, and due to this wpa_supplicant's
finish_handler() not getting called. Fix this by returning NL_SKIP
instead while still ignoring all possible additional frequencies.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
There are two hw modes (5 GHz and 6 GHz) with HOSTAPD_MODE_IEEE80211A
and the current hw mode may be wrong after one channel switch to 6 GHz.
This will cause hostapd_set_freq_params() to return -1 when saving
previous state and the second channel switch to fail. Fix this by adding
hostapd_determine_mode() before every channel switch.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use zero value with QCA_WLAN_VENDOR_ATTR_CONFIG_EHT_MLO_MAX_NUM_LINKS to
restore the device default maximum number of allowed MLO links
capability.
Also, as per IEEE 802.11be/D3.0, the maximum number of allowed links for
an MLO connection is 15. Update the documentation of the attribute to
indicate the same.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
This is needed to match the key configuration design with a single
netdev and the nl80211 driver interface.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
In case of MLO AP and legacy client, make sure received EAPOL frames are
processed on the correct BSS.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In case of MLO AP and legacy client, make sure Management frame TX
status is processed on the correct BSS.
Since there's only one instance of i802_bss for all BSSs in an AP MLD in
the nl80211 driver interface, the link ID is needed to forward the
status to the correct BSS. Store the link ID when transmitting
Managements frames and report it in TX status.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In case of MLO AP and legacy client, make sure EAPOL TX status is
processed on the correct BSS.
Since there's only one instance of i802_bss for all BSSs in an AP MLD in
the nl80211 driver interface, the link ID is needed to forward the EAPOL
TX status to the correct BSS. Store the link ID when transmitting EAPOL
frames over control interface and report it in TX status.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Only the main link handles SAE authentication and OWE, skip them on
other links.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
MLO associations use the MLD address instead of the MAC address in SAE
derivation.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
If the AP is part of an AP MLD specify the link ID in the set_key
parameters whenever setting a group key.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This provides the link specific group keys and last used PN/IPN/BIPN
values to the Supplicant in the MLO KDEs instead of the KDEs used for
non-MLO cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Verify that the MLD address in EAPOL-Key msg 4/4 is set correctly for
MLO cases. Note that the mechanism used here for distinguishing between
EAPOL-Key msg 2/4 and 4/4 is not exactly ideal and should be improved in
the future.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This provides the link specific group keys and last used PN/IPN/BIPN
values to the Supplicant in the MLO KDEs instead of the KDEs used for
non-MLO cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Allow RSN authenticator to fetch the current group key information with
the keys and the last used PN/IPN/BIPN for MLO specific KDEs.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Verify that the affiliated link information matches between association
(unprotected) and 4-way handshake (protected).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Make the MLO related information available for the RSN Authenticator
state machine to be able to perform steps needed on an AP MLD. The
actual use of this information will be in the following commits.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This is needed since link_id is not always available. In addition,
recognize the link address as a known address.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
EAPOL frames may need to be transmitted from the link address and not
MLD address. For example, in case of authentication between AP MLD and
legacy STA. Add link_id parameter to EAPOL send APIs.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This allows proper TX status handling when MLD addressing is used for
Management frames. Note, that the statuses are still not forwarded to
the correct link BSS. This will be handled in later commits.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This is needed for the driver to know on which link it should transmit
the frames in MLO cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Get rid of the duplicated code for setting IEEE 802.1X port
authorization for MLD and non-MLD cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Handle IEEE 802.1X port authorization in the context of MLO.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When a non-AP MLD is deauthenticated/disassociated from an MLD AP, make
sure to clean up its state from all links.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This is a step towards handling of deauthentication/disassociation from
an MLD AP.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Handle association request callback in the context of MLO.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add the full station profile to the Multi-Link element in the
(Re)Association Response frame. In addition, use the AP MLD's MLD MAC
address as SA/BSSID once the non-AP MLD has been added to the driver to
use address translation in the driver.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Implement processing of the Multi-Link element in the (Re)Association
Request frame, including processing of the Per-STA Profile subelement.
After handling the basic parsing of the element and extracting the
information about the requested links, handle the link specific
processing for each link:
- Find the interface with the corresponding link ID.
- Process the station profile in the interface.
- Prepare the Per-STA Profile subelement to be included in the
Multi-Link element in the (Re)Association Response frame.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Find an AID that is unused on all the affiliated links when assigning an
AID to a non-AP MLD.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In case the AP is an AP MLD, parse the Multi-Link element from the
Authentication frame, store the relevant information, and prepare the
response Multi-Link element.
If the AP is not an AP MLD or the parsing of the element fails, continue
the authentication flow without MLD support.
For SAE, it is needed to skip various fixed fields in
the Authentication frame. Implement it for SAE with H2E.
TODO: This should be extended to other authentication algorithms which
are allowed for MLD connections and have fixed fields in the
Authentication frames, according to IEEE P802.11-REVme/D3.0, Table 9-69
(Presence of fields and elements in Authentications frames).
This commit doesn't support FILS, FT, etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Define a struct to hold MLD station info and implement publishing of the
Basic Multi-Link element. Add it into Beacon and Probe Response frames.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Once a station is added to the underlying driver, the driver is expected
to do address translation and use MLD addresses. Thus, when handling a
received Management frame, match it against the MLD address.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
To simplify the handling of MLD stations, assume that all
interfaces/BSSs use the same IEEE 802.1X authenticator, the same RADIUS
server instance, and the same RADIUS client.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In MLO, multiple BSSs can transmit on different frequencies. Select
link frequencies according to the transmitter address.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
- Include RNR element in Beacon frames of AP MLDs.
- Whenever a new interface is added to an AP MLD, reconfigure
the Beacon frame templates for all other interfaces, to allow
updating their RNR elements.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This includes:
- Modifications of the driver API, to include the link ID as part
of 'struct hostapd_freq_params'.
- Modifications to nl80211 driver.
- Modifications for the driver wrappers.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
To be used in later patches, e.g., for link tracking etc.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add support for including multiple hostapd interfaces in the same AP
MLD, i.e., all using the same underlying driver network interface.
To do so, when a new hostapd interface is added, if there is already
another interface using the same underlying network interface, associate
the new interface with the same private data object, instead of creating
a new one.
As some of the BSSs are non-first BSSs, meaning that they reuse the
drv_priv of the initial BSS, make sure not to double free it.
Currently multiple BSS entries are not supported so always use bss[0]
for MLD.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Retrieve the EML capabilities as well as the MLD capabilities and ops
from nl80211 and expose them using the new driver interface
get_mld_capa().
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
We will start using this structure to also track MLD related
capabilities instead of just extended capabilities. As such, give the
structure a more generic name.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
AP cannot come up in channels that are marked as NO_IR. If AP moves to
HAPD_IFACE_DISABLED state, it will deinitialize the nl80211 driver
interface and sockets.
Hence, introduce a new state called HAPD_IFACE_NO_IR, for 6 GHz APs to
handle NO_IR scenarios, such as AFC, where the channels not allowed by
AFC will have HOSTAPD_CHAN_NO_IR flag set. In this state, AP is still
kept in a non-operational state (stopped) without deinitializing the
nl80211 driver interface. wiphy reg change event can then update the
channels and bring up the AP in a valid channel.
Signed-off-by: Pooventhiran G <quic_pooventh@quicinc.com>
Define a QCA vendor command to configure MLO link id to the driver on
which the TDLS discovery response frame needs to be transmitted when the
local station is connected in MLO mode. This command is configured to
the driver the prior to every TDLS discover frame transmission when the
station is connected in MLO mode. If the station is connected in non-MLO
mode this command is not configured to the driver for TDLS discovery
frame transmission.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support to indicate link reconfiguration event reported by the QCA
vendor interface to the wpa_supplicant control interface.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support to indicate TID-to-link mapping changes reported by the QCA
vendor interface to the wpa_supplicant control interface.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Per IEEE P802.11az/D7.0, 12.12.3.2 (PASN Frame Construction and
Processing), responder should REFUSE PASN authentication frame 1 with
Base AKM as PASN AKM if dot11NoAuthPASNActivated is false. That
configuration was not previously available and hostapd was hardcoded
with dot11NoAuthPASNActivated being true.
Allow this to be configured and reject PASN authentication frame 1 from
initiator if pasn_noauth=0 and Base AKM in RSNE of this frame is PASN.
The default value for pasn_noauth is 1 to maintain previous
functionality even though the dot11NoAuthPASNActivated is defined to
have default value of false.
Signed-off-by: Sai Pratyusha Magam <quic_smagam@quicinc.com>
The current value of 50 is not sufficient for getting survey info for
all the frequencies when the 6 GHz band is enabled. Increase the limit
to 100 to be able to receive survey info for 6 GHz frequencies also.
Signed-off-by: Ainy Kumari <quic_ainykuma@quicinc.com>
Add a new vendor command and attributes to notify TID-to-link mapping
changes to the userspace.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Setting 4addr mode on fronthaul BSS breaks WPS association on backhaul
STA which is still on 3addr mode.
Fix the interop issue by not setting 4addr mode on fronthaul BSS with
WPS instead of setting by default for multi-ap case.
Fronthaul BSS for non-WPS STA shall continue to use 4addr mode.
Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
The parameter req_pmk_r1_name was not used at all in the function
wpa_ft_local_derive_pmk_r1(). In addition, the PMK-R1-NAME should be
updated in this function along with the PMK-R1. This means the parameter
should change from "req_pmk_r1_name" to "out_pmk_r1_name" to match the
design used for other paths that derive the PMK-R1.
sm->pmk_r1_name needs to be properly updated when pmk_r1_name is derived
from the local pmk_r0.
Signed-off-by: Adil Saeed Musthafa <quic_adilm@quicinc.com>
Prune-associations should be done only after the new station is
authorized. Otherwise any STA can cause denial of service to connected
stations in PMF case when more than a single interface is being
controlled by the same hostapd process.
Signed-off-by: Adil Saeed Musthafa <quic_adilm@quicinc.com>
Define a new QCA vendor attribute to configure channel bandwidth to the
driver for CTS frame transmission. This is used for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN in
enum qca_wlan_vendor_features to indicate the device supports enhanced
audio experience over WLAN feature.
Also, update the documentation where other subcommand(s) or attribute(s)
require this new feature flag. These subcommand(s) and attributes are
under development and would be restricted to the supported drivers
advertising QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN.
As such, it is still acceptable to introduce a new requirement for the
previously defined interface.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Add vendor attributes for EHT testbed STA configuration.
This includes enabling STR MLMR mode and forcing power save
on active MLO links for a defined number of beacon periods.
Signed-off-by: Gururaj Pandurangi <quic_panduran@quicinc.com>
Add vendor attributes related to MLO and EMLSR mode
capability configuration for EHT testbed STA. It includes
EHT OM control support and EMLSR padding delay configuration.
Also, generalise the naming of HE OMI control enumeration to
OMI control as it now consists of both HE and EHT OMI control
fields.
Signed-off-by: Gururaj Pandurangi <quic_panduran@quicinc.com>
Some station devices are apparently sending the EAPOL-Logoff message in
some cases before the initial authentication for WPA2/WPA3-Enterprise.
hostapd would have forced a "post EAP-Failure" disconnection in 10 ms
for such cases while still allowing the EAP authentication to try to
complete.
This is not ideal and could result in interoperability issues, so skip
the forced disconnection in the particular case where the EAPOL-Logoff
message is received before the first authentication is completed.
In addition, disconnect the STA without starting new EAP authentication
and the 10 ms delay if an EAPOL-Logoff message is received after
authentication has been completed successfully. This results in cleaner
behavior by avoiding the extra start of a new EAP authentication in a
case where the STA is going to be disconnected shortly.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add vendor attributes related to MLO and EMLSR mode
capability configuration for EHT DUT. This includes forcing
active MLO links and invoking EMLSR mode entry or exit.
Signed-off-by: Gururaj Pandurangi <quic_panduran@quicinc.com>
Some of the information elements added in IEEE Std 802.11ax-2013 for VHT
purposes have since then been taken into use for other cases and renamed
to remove the "VHT" prefix in the standard. Update the defines for those
elements in the implementation to match the names used in the current
standard.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add validatation of center frequency, and filling of appropriate
bandwidth in the channel switch wrapper when the channel switch is done
to a 320 MHz channel.
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
The execute bits were not supposed to be added to a source code file.
Fixes: 927dbfb453 ("Fix 40 MHz channel bringup with ACS on the 6 GHz band")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use the op_class configuration to determine whether to select the 5 GHz
or 6 GHz mode for ACS. Without this, the first mode (5 GHz in most
cases) would have been selected regardless of the op_class value.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When AP is brought up in HE40/EHT40 with ACS, the AP comes up with 20
MHz bandwidth. It is expected to come up with 40 MHz bandwidth.
conf->secondary_channel does not hold the correct value and it leads to
choosing 20 MHz in hostapd_set_freq_params(). conf->secondary_channel is
filled using the hostapd config he_oper_centr_freq_seg0_idx. When AP is
configured to use ACS, the hostapd config he_oper_centr_freq_seg0_idx is
not valid as the channel is not known during bring up. So using the
config he_oper_centr_freq_seg0_idx to fill the conf->secondary_channel
does not work with ACS.
Use op_class to determine the bandwidth and based on the bandwidth fill
the conf->secondary_channel to address this ACS case.
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
This adds more production-like testing coverage for KDK derivation. Both
SAE and OWE transition mode are covered. The latter has some corner
cases that did not work correctly previously.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When 6 GHz band is specified and hw_mode parameter is set to any,
hostapd_determine_mode() may determine the wrong mode because there are
two hw modes (5 GHz and 6 GHz) with HOSTAPD_MODE_IEEE80211A. This will
cause 6 GHz AP to fail to start. Fix this by adding a check similar to
the changes in commit 99cd453720 ("hw_feature: Correctly select mode
in case of the 6 GHz band") into hostapd_determine_mode().
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
IEEE 802.11be enables multiple links between STA and AP. Each of the
link has its own set of statistics. Add additional attributes required
to fetch link layer statistics per MLO link.
For MLO connection, per MLO link statistics will be sent with the new
attribute QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. Also, cumulative
statistics of all the MLO links will be sent outside
QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK to be compatible with legacy user
space.
For non-MLO connection, the statistics will be sent without being nested
inside QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK attribute.
Co-authored-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
The attributes QCA_WLAN_VENDOR_ATTR_LL_STATS_PAD and
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NF_CAL_VAL were allocated the same
attribute number in error. QCA_WLAN_VENDOR_ATTR_LL_STATS_PAD attribute
is known to not be used; thus, it is safe to be renumbered.
Fixes: 1491fc64a8 ("Define QCA vendor per-enum 64-bit pad attributes")
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
When user space triggers a scan, the firmware aborts background scan,
and uses the roam status QCA_ROAM_FAIL_REASON_CURR_AP_STILL_OK instead
of "Invalid roam failures reason".
Signed-off-by: Chunquan Luo <quic_chunquan@quicinc.com>
Define bitmap values used by LL_STATS vendor command
and update the corresponding kernel documentation.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
hostapd start AP flow changed in commit 931e5d4f9e. However, that
could cause a regression in a legacy AP driver where the set key
operation for GTK, IGTK, and BIGTK before AP start (set beacon) would
cause the driver to ignore the key set command. Restore the flow of the
set beacon and WPA key init operations to make sure drivers can receive
and set group keys correctly.
Fixes: 931e5d4f9e ("mbssid: Configure all BSSes before beacon setup")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support to configure the allowed frequency list for AP operation
using a QCA vendor interface before NL80211_CMD_NEW_BEACON/
NL80211_CMD_START_AP. hostapd generates the allowed frequency list by
intersecting user configured frequency list and all the frequencies
advertised by the driver including disabled channels. If user doesn't
specify allowed frequency list, all the frequencies advertised by the
driver, including disabled channels, will be configured.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
In theory, each device that supports WMM (or the IEEE 802.11 QoS for
that matter) is expected to advertise how many replay counters it
supports and the peer device is supposed to use that information to
restrict the total number of different MSDU priorities (AC/UP) that
might be used. In practice, this is not really done in deployed devices
and instead, it is just assumed that everyone supports the eight
different replay counters so that there is no need to restrict which
MSDU priorities can be used.
hostapd implementation of WMM has advertised support for 16 PTKSA replay
counters from the beginning while wpa_supplicant has not had any code
for setting the supported replay counter fields in RSNE, i.e., has left
the value to 0 which implies that only a single replay counter is
supported. While this does not really result in any real issues with
deployed devices, this is not really correct behavior based on the
current IEEE 802.11 standard and the WMM specification.
Update wpa_supplicant to use similar design to the hostapd RSNE
generation by setting the number of supported PTKSA replay counters to
16 whenever WMM is enabled. For now, this is done based on the
association being for HT/VHT/HE/EHT and also based on the AP supporting
WMM since it is much more likely for the local device to support WMM and
eight replay counters (which can be indicated only with the value that
implies support for 16 counters since there is no separate value for 8).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add new nested netlink attribute, NL80211_ATTR_EMA_RNR_ELEMS, to send
the reduced neighbor report (RNR) elements to the driver when EMA is
enabled. This attribute includes the count of RNR elements and data at
each index. While generating EMA beacons, the driver will include RNR
group at a given index along with MBSSID group. The last element, if
present, has RNR data common for all EMA beacons such as neighbor APs.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
As per IEEE Std 802.11ax-2021, 11.1.3.8.3 Discovery of
a nontransmitted BSSID profile, an EMA AP that transmits a Beacon
frame carrying a partial list of nontransmitted BSSID profiles
should include in the frame a Reduced Neighbor Report element
carrying information for at least the nontransmitted BSSIDs that
are not present in the Multiple BSSID element carried in that frame.
Add this support by splitting the reduced neighbor report (RNR) in as
many elements as the number of multiple BSSID elements. Each RNR element
excludes the non-transmitting profiles already included in the MBSSID
element at the same index. If present, the last additional group will
have the data common for all EMA beacons such as neighbor AP information
gathered through neighbor reports.
The hwsim test case he_ap_ema demonstrates this support.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Do not include interfaces on the same radio in reduced neighbor
report elements (RNR) as multiple BSSID elements from the same
management frame already include these if MBSSID feature is enabled.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Add a vendor feature flag for the driver to indicate support for allowed
frequency configuration in AP mode.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add a new vendor command to trigger computation of connected channel
statistics such as channel utilization in STA mode.
Signed-off-by: Ainy Kumari <quic_ainykuma@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Define a new attribute QCA_WLAN_VENDOR_ATTR_CONFIG_AP_ALLOWED_FREQ_LIST
to configure the full list of allowed frequencies for the AP operation.
The configuration is valid only from the next BSS start until the BSS is
stopped. The drivers shall filter out channels on top of this list of
channels based on regulatory or other constraints. This can be used to
specify user's choice of frequencies, allowed list of channels with
static puncturing feature, etc.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
