A driver may not support setting MAC address when interface is UP, so
wpa_supplicant used to always sets the interface down for MAC address
change.
Try to change the address first without setting the interface down and
then fall back to DOWN/set addr/UP if the first attempt failed. This can
reduce the interface setup time for time-critical use cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Parse the reconfiguration Multi-Link element and:
- Don't select a BSS for connection if it is part of an MLD
and is going to be removed.
- Don't scan for missing links that are to be removed.
- Don't include removed links in association.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add support for building and sending ML probe requests. During connect,
try to send an ML probe request if we are going to connect to an MLD AP
and the BSS information for some of the links is missing.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Extend 'struct wpa_driver_scan_params' to allow higher layer to indicate
if minimal probe request content should be included by the driver as part
of the scan logic.
Implement this with driver_nl80211, by setting
NL80211_SCAN_FLAG_MIN_PREQ_CONTENT.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Make the current HE BSS color available in STATUS command output since
this can change dynamically based on color collisions.
Signed-off-by: Antonio Prcela <antonio.prcela@gmail.com>
Signed-off-by: Antonio Prcela <antonio.prcela@sartura.hr>
Previously the NL80211_CMD_SET_QOS_MAP command was sent to the radio
interface. Send this command using nl80211_cmd_msg() and the bss,
instead of drv.
Signed-off-by: Arnon Meydav <ameydav@maxlinear.com>
Certain internet service providers transmit VLAN 0 priority tagged
EAPOL frames from the ONT towards the residential gateway. VID 0
should be ignored, and the frame processed according to the priority
set in the 802.1P bits and the encapsulated EtherType (i.e., EAPOL).
The pcap filter utilized by l2_packet_* is inadquate for this use case.
Here we modify the pcap filter on FreeBSD to accept both unencapsulated
and encapsulated (with VLAN 0) EAPOL EtherTypes. This preserves the
original filter behavior while also matching on encapsulated EAPOL.
Additional work is required to support this handling on other platforms.
We also modify the rx_receive handler to offset the packet buffer
and length when handling dot1q encapsulated frames so the existing
packet parsing code works as-is.
Signed-off-by: R. Christian McDonald <rcm@rcm.sh>
Sponsored by: Rubicon Communications, LLC ("Netgate")
The range for the 5 GHz channel 118 was encoded with an incorrect
channel number.
Fixes: ed8e13decc (ACS: Extract bw40/80/160 freqs out of acs_usable_bwXXX_chan())
Signed-off-by: Michael Lee <michael-cy.lee@mediatek.com>
It is valid to configure an AP to be both backhaul and
fronthaul (multi_ap=3), so we should not test for a missing
fronthaul flag but instead test directly for backhaul capability.
Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
The way these checks were done for WPS enabled APs were unnecessarily
complex and missed one of the cases. Simplify this by doing the check
only once and do that earlier in the process to minimize changes to STA
state.
Fixes: a7f55f7f68 ("WPS: Enable SA Query checks for WPS AP")
Signed-off-by: Jouni Malinen <j@w1.fi>
Currently if ch_switch_vht_config is present, only ieee80211ac config
will be updated in hostapd_config and ieee80211ax/ieee80211be config may
be wrong. Fix this by adding handlings for ch_switch_he_config and
ch_switch_eht_config as well.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
free_cb can be NULL during the pmksa_cache_auth_init() from the modules
using libpasn.so. So check it explicitly before dereferencing.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
wpa_supplicant postpones expired PMKSA deletion untillassociation is
lost for SAE to avoid forced disconnection. But during this time the
driver may use the expired PMKSA for reassociation with the current
connected AP.
Remove the current PMKSA for SAE from the driver after reauth threshold
is passed when the driver takes care of BSS selection.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Increase the first group rekey timeout from 500 ms to 1000 ms when the
number of associated stations is greater than 100. This is to avoid
client disconnections due to group handshake timeout in multiclient
scenarios where it might take more than 500 ms to be able deliver Group
Key msg 1/2 to all associated STAs.
Signed-off-by: Sai Pratyusha Magam <quic_smagam@quicinc.com>
Add support for EHT phy index and maximum NSS as per IEEE P802.11be/D4.0,
9.6.7.36 and 9.4.2.313.4.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Maximum NSS calculation for HE mode checks if both Tx and Rx support
a given NSS. Modify it to instead check if either of these two support
the given NSS.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Rename the local variable mcs_nss_size to he_mcs_nss_size in
hostapd_fils_discovery_cap() and hostapd_gen_fils_discovery_nss()
to limit its usage to HE mode.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Move the phy index determination for FILS discovery frames to a new
function without changing the functionality. HE support is mandatory for
operating in the 6 GHz band hence the phy index will always be set to
FD_CAP_PHY_INDEX_HE for this band.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
The sae_password_entry is used in this function only if CONFIG_SAE is
defined, so declare this variable only under the same condition.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Update Wide Bandwidth Channel Switch element as per IEEE
P802.11-REVme/D4.0, 9.4.2.159 (Wide Bandwidth Channel Switch element)
and Table 9-314 (VHT Operation Information subfields).
Update New Channel Width, New Channel Center Frequency Segment 0, and
New Channel Center Frequency Segment 1 fields as per IEEE
P802.11-REVme/D4.0 for 160 MHz and 80+80 MHz bandwidth. This replaces
the use of now deprecated Channel Width 2 and 3 values with a more
backwards compatible design.
Signed-off-by: Yuvarani V <quic_yuvarani@quicinc.com>
Do not reject reauth threshold passed PMKSA indicated in successful
association event since the PMKSA is still valid.
Additionally, remove the reauth threshold passed PMKSA entry from the
driver to prevent using it further in the driver.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Wi-Fi Aware pairing responder needs to forward the derive PMK to the
framework on successful pairing setup. The framework will set
corresponding PMK while a pairing verification is initiated by the
paired peer. Since the PMK is not updated for responder's PASN context,
framework does not have a valid PMK and verification fails. Hence copy
the derived PMK to PASN context.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Currently, during association handling, if any of the iface parameters
changes due to some reason, it calls ieee802_11_set_beacons() function.
This function sets beacon for the all the BSSes in that iface even if
the beacon was not set already. This leads to setting the beacon
prematurely for some BSSes which was intentionally not started.
Fix the above issue by calling ieee802_11_update_beacons() function
instead. This function only updates the beacon if it was already set.
While at it, do the same while freeing STA entry.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Based on IEEE Std 802.11-2020 Table E-3 (Operating classes in Japan) and
Table E-4 (Global operating classes), we update channel 144 for those
corresponding operating classes.
The changes applicable to the global operating classes fixes an issue of
P2P GO not starting on channel 144 (frequency 5720 MHz) in cases where
the driver supports DFS operations.
Signed-off-by: Shuibing Dai <shuibing@google.com>
Enumeration qca_wlan_roam_stats_frame_subtype defines the various frame
subtypes which may be collected by the driver and reported via the
QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_SUBTYPE attribute.
Two of the enumerators are:
* QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_PREAUTH
* QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_REASSOC
These were initially defined and used to respectively report
Authentication Response and Reassociation Response frames.
Now there is a requirement to also report Authentication Request and
Reassociation Request frames. In order to satisfy this requirement,
add two new enumerators:
* QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_AUTH_REQ
* QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_REASSOC_REQ
Note that the first of these uses the standard term "AUTH" instead of
the confusing term "PREAUTH" used previously.
And to align with that naming, and in order to clearly show the usage
of the original enumerators, rename them to:
* QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_AUTH_RESP
* QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_REASSOC_RESP
Furthermore, Authentication Request/Response frame refers to the
Authentication frames sent by the non-AP STA and AP, respectively.
And finally, to support backward compatibility with applications using
the original enumerators, redefine those in terms of the new names.
Signed-off-by: Chunquan Luo <quic_chunquan@quicinc.com>
Fetch AP BSSID from each roam connection frame and cache the info in the
WLAN driver. When user space gets roam stats by
QCA_WLAN_VENDOR_ATTR_ROAM_STATS_INFO, user space can now collect the AP
BSSID info for roam issue.
Signed-off-by: Chunquan Luo <quic_chunquan@quicinc.com>
Redesign the identity selection for MK derivation to be done explicitly
based on the last indicated identity (whether it is from
EAP-Response/Identity or method specific AT_IDENTITY) during the current
exchange. This makes the implementation cleaner and avoids cases were
more or less duplicated selection steps ended up being slightly
different. This is not as clean as it could otherwise be due to the
exception needed for the IMSI privacy case where the identity used in MK
derivation is actually not the one exchanged in the EAP messages.
Furthermore, this moves the somewhat confusing EAP method specific
tracking of the lasgt EAP-Response/Identity value from EAP-SIM/AKA into
the main EAP peer implementation.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow the EAP-SIM/AKA server to be configured to use a smaller limit for
the number of times fast re-authentication can be used before falling
back to running full authentication. This is particularly useful for EAP
peer testing to cover cases when falling back from fast
re-authentication to full authentication in various different cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
While the EAP-SIM/AKA RFCs recommend against doing this, some deployed
authentication servers use the identity from the EAP-Response/Identity
directly without using an EAP method specific indication (AT_IDENTITY).
Having a capability to configure hostapd EAP server to behave in this
manner helps in increasing testing coverage for the EAP peer
implementation.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
A case was missing in the way wpa_supplicant was tracking the identity
that is used when deriving MK if the EAP server does not follow the RFC
guidance on using EAP method specific identity determination (i.e.,
AT_IDENTITY for EAP-SIM/AKA) combined with a fallback from fast
re-authentication to full authentication. wpa_supplicant ended up using
the actual identity instead of the last identity included in an EAP
message even though MK derivation is supposed to use the identity that
was included in the last AT_IDENTITY or in the EAP-Response/Identity if
AT_IDENTITY was not used. This resulted in such an authentication
attempt failing due to incorrect MK being derived and AT_MAC validation
resulting in an mismatch.
Fix this by checking for the case where fast re-authentication is
attempted and the server recognizes the fast re-auth identity, but
decides to fall back to full authentication without a separate EAP
method specific identity exchange using AT_IDENTITY. This allows the
fast re-auth identity from EAP-Response/Identity to be used in MK
derivation in such cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Define a new QCA vendor attribute to configure traffic
shaping policy applied during coex scenarios.
Signed-off-by: Shailendra Singh <quic_shasing@quicinc.com>
Add an attribute QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_IS_ML to the
ADD_STA_NODE command. If this attribute is set, it implies that the node
being added is an MLD node.
Signed-off-by: Adil Saeed Musthafa <quic_adilm@quicinc.com>
Extend QCA_WLAN_VENDOR_ATTR_CONFIG_CHAN_WIDTH_UPDATE_TYPE attribute to
support handling interoperability issues with APs which don't handle
the maximum bandwidth change indication correctly.
Additionally define an enum for possible values of
QCA_WLAN_VENDOR_ATTR_CONFIG_CHAN_WIDTH_UPDATE_TYPE.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add QCA vendor attributes to indicate various MLO capabilities supported
by the WLAN driver to userspace. These capabilities are usually reported
by the firmware during the initial bootup handshake with the driver.
Signed-off-by: Mukul Sharma <quic_mukul@quicinc.com>
Add the copied EHT capabilities into the sta_add() call when adding a
TDLS peer.
The mld_link_id value was previously only for AP mode, but it can now be
used for TDLS links as well to indicate the link on which a
single-link-TDLS direct link is negotiated.
Signed-off-by: Jouni Malinen <quic_klokere@quicinc.com>
When the current association is with an AP MLD, the BSSID for TDLS
operations needs to be selected based on which link is used to transmit
the frames.
Signed-off-by: Jouni Malinen <quic_klokere@quicinc.com>
When the current association is with an AP MLD, the Discovery Response
needs to be sent using the link that matches the indicated BSSID.
Signed-off-by: Jouni Malinen <quic_klokere@quicinc.com>
This is needed to be able to determine which link is used for TDLS setup
when the current association is with an AP MLD.
Signed-off-by: Jouni Malinen <quic_klokere@quicinc.com>
This is needed to be able to configure the STA entry into the driver
with the information for EHT.
Signed-off-by: Jouni Malinen <quic_klokere@quicinc.com>
For now, only a vendor command is available for this functionality that
is needed to implement single-link TDLS during an MLO association.
Signed-off-by: Jouni Malinen <quic_klokere@quicinc.com>
This is needed to allow the driver to know on which operating channel
(as specified by the link that is affiliated with AP MLD for the current
association) is used for transmitting TDLS Discovery Response. This
commit adds the link_id parameter to various functions, but does not
implement the driver interface change itself.
Signed-off-by: Jouni Malinen <quic_klokere@quicinc.com>
wpa_supplicant does not configure BIGTK(s) to the driver when the STA
reconnects to the same AP after disconnect due to not clearing the last
configured BIGTK values during disconnect. To avoid such issues clear
the BIGTK values while clearing PTK and other group keys.
Fixes: 2d4c78aef7 ("Configure received BIGTK on station/supplicant side")
Fixes: f15cc834cb ("MLD STA: Processing of EAPOL-Key msg 3/4 frame when using MLO")
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
The ap_mld_addr entry was added without introducing a new mask bit which
does not follow the expected style for adding new information into the
BSS command and might result in unexpected behavior for external
components. Define a new BSS command information mask bit for this AP
MLD address and print the AP MLD address in the BSS info only if the
mask bit is set.
Fixes: db99e7341a ("Add AP MLD address into BSS command output")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a vendor attribute for an EHT DUT to configure the type of TID-To-Link
Mapping Negotiation Support for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a QCA vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_AMPDU_CNT to
enable configuration of TX maximum aggregate size with a specific peer.
This can be used to improve performance in noisy environment. In AP
mode, the peer MAC address of the associated STA is specified with
QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_MAC.
Signed-off-by: Will Huang <quic_wilhuang@quicinc.com>
Rename the attribute QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC
to a generic name QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_MAC, so other
configuration commands can reuse it. And make backward compatibility of
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC, define it as same
value of QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_MAC (35).
Signed-off-by: Will Huang <quic_wilhuang@quicinc.com>
The driver might decide to change the operating band on its own, e.g.,
when trying to use a single channel in AP + AP case. A CSA event will be
notified to hostapd to update the channel/frequency, but hw_mode did not
get updated accordingly.
This may cause hostapd interface restarting to fail, e.g., with control
interface DISABLE / ENABLE commands at configured_fixed_chan_to_freq(),
because of the mismatch between conf->channel and conf->hw_mode.
Update hw_mode right after channel change to fix this.
Signed-off-by: ngong <quic_ngong@quicinc.com>
Per IEEE P802.11be/D4.0, 9.4.2.316 (QoS Characteristics element), enable
support for the following optional QoS Characteristics parameters:
- Maximum MSDU Size
- Service Start Time
- Service Start Time LinkID
- Mean Data Rate
- Delayed Bounded Burst Size
- MSDU Lifetime
- MSDU Delivery Info
- Medium Time
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Add support to configure the mandatory QoS Characteristics parameters
per IEEE P802.11be/D4.0, 9.4.2.316 (QoS Characteristics element), in SCS
request:
- Minimum Service Interval
- Maximum Service Interval
- Minimum Data Rate
- Delay Bound
Enable STA SCS traffic descriptor support for EHT connection when the
connected EHT AP advertises SCS traffic descriptor capability in the EHT
Capabilities element.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Set WFA capability to allow non-EHT SCS Traffic support in association
elements when the AP advertises support for non-EHT SCS Traffic support
via Beacon or Probe Response frame. This capability is upper layer
functionality and as such, does not need a separate driver capability
indication or configuration, but indicate this only if the AP supports
the feature to minimize risk of interoperability issues with a new
information element.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Add a vendor attribute for EHT testbed STA to configure MLD ID in the ML
Probe Request frame transmitted as part of host initiated scan request.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Get rid of the warning about unrecognized Fragment element when FTE is
fragmented and make the total length of the FTE itself and the following
Fragment elements available. For now, use a separate variable for the
total length to avoid confusing existing callers.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The FTE parser itself used valid data, but the reassembled buffer was
available only during the parser run. That buffer will be needed for the
caller as well since most of the parsed data is used as pointers instead
of copied data.
Store the reassembled buffer in struct wpa_ft_ies and require
wpa_ft_parse_ies() callers to use wpa_ft_parse_ies_free() to free any
possibly allocated temporary data after wpa_ft_parse_ies() calls that
return success (0).
Fixes: 43b5f11d96 ("Defragmentation of FTE")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This replaces the earlier commit 4c079dcc64 ("Increment
hmac_sha*_vector() maximum num_elem value to 25") with a smaller
increment of just one extra element since the updated FTE MIC
calculation design does not use separate elements. This reduces stack
memory need. In addition, this starts using a define value for the
maximum number of vector elements to make this easier to change and to
make the code more readable.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Generate the "extra" data buffer outside wpa_ft_mic() to make this
function easier to share for MLO FT Reassociation Response frame. This
replaces the earlier design in commit e6f64a8e1d ("FT: FTE MIC
calculation for MLO Reassociation Request frame").
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend wpa_ft_mic() to take in an array of link addresses to allow the
FTE MIC to be calculated for Reassociation Request frame as described in
IEEE P802.11be/D4.0, 13.8.4. This commit does not change actual
behavior, i.e., this is just preparing wpa_ft_mic() and the existing
callers with a new argument.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is needed for FTE MIC calculation for Reassociation Request frmae
when using MLO which could add 15 link addresses into the input data.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new QCA vendor sub command QCA_NL80211_VENDOR_SUBCMD_TX_LATENCY to
configure, retrieve, and report per-link transmit latency statistics.
When used as a command, userspace configures transmit latency monitoring
and get the corresponding statistics of the last period. When used as a
command response, driver replies the get action from userspace with the
statistics of the last period. When used as an event, driver reports the
statistics periodically.
Signed-off-by: Yu Wang <quic_yyuwang@quicinc.com>
When a CHANNEL_LIST_CHANGED event is received, memory of
iface->hw_features is freed and allocated again with
hostapd_get_hw_features(), but iface->current_mode still refer to the
original memory address, which is not correct since that memory has been
freed. This could happen in cases where the driver provides channel list
updates during the lifetime of the started BSS.
Fix this by updated iface->current_mode to point to the new array of hw
features.
Fixes: 0837863fbc ("AP: Handle 6 GHz AP state machine with NO_IR flags")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Typecasting takes precedence over division here, so the legacy rates
larger than 255 * 100 kbps (i.e., 36, 48, 54 Mbps) ended up getting
truncated to invalid values.
Fix this by typecasting the value after the division.
Fixes: d4f3003c56 ("nl80211: Configure Beacon frame TX rate if driver advertises support")
Signed-off-by: Prasanna JS <quic_pjs@quicinc.com>
interfaces.iface[i] might be NULL when going through the cleanup of all
remaining interfaces at the end of the process termination. The changes
for clearing drv_priv in AP MLD cause that cleanup process to crash on
dereferencing a NULL pointer.
Fix this by explicitly checking that the interface context is available
before trying to clear the pointer to driver data.
Fixes: 7fa99b3246 ("AP: Allow starting multiple interfaces within single MLD")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Define an attribute for high RSSI roam trigger threshold. STA is
expected to trigger roam if the current connected AP's RSSI gets above
this high RSSI threshold. STA's roam attempt on high RSSI threshold aims
to find candidates from other better Wi-Fi bands.
Signed-off-by: Sunil Dutt <quic_usdutt@quicinc.com>
Add three vendor roam control attributes to configure the roaming
parameters dynamically.
QCA_ATTR_ROAM_CONTROL_CONNECTED_LOW_RSSI_THRESHOLD controls the
connected AP's low RSSI threshold to trigger the neighbor lookup.
QCA_ATTR_ROAM_CONTROL_CANDIDATE_ROAM_RSSI_DIFF and
QCA_ATTR_ROAM_CONTROL_6GHZ_CANDIDATE_ROAM_RSSI_DIFF control the RSSI
difference threshold between the connected AP and the new candidate AP
for the roam to trigger.
Co-authored-by: Sunil Dutt <quic_usdutt@quicinc.com>
Signed-off-by: Sunil Dutt <quic_usdutt@quicinc.com>
Extend enum qca_wlan_vendor_attr_mlo_peer_prim_netdev_event to add MLD
MAC address, the number of links, and link info. Link info contains
ifindex and MAC address of each link of a non-AP MLD that was negotiated
in ML association.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add vendor attribute IDs QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ORIGINAL_BSSID,
QCA_WLAN_VENDOR_ATTR_ROAM_STATS_CANDIDATE_BSSID, and
QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ROAMED_BSSID for updating roaming AP
BSSID to user space to enable user space collecting the BSSID for
roaming issues.
Signed-off-by: Chunquan Luo <quic_chunquan@quicinc.com>
Add support to obtain the start channel when checking whether DFS
is required when using 320 MHz channels.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Determine the channel width by operating class for the 6 GHz band when
validating puncturing bitmap. This is needed to allow puncturing to be
used with 320 MHz channels.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add mld_addr configuration option to set the MLD MAC address.
The already existing bssid configuration option can be used to
control the AP MLD's link addresses.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
When STAs connect to transmitted BSS and nontransmitted BSS, the
AP should assign the aIDs from the same pool.
Use the transmitted BSS AID pool to assign AIDs when the AP enables
multiple BSSID.
Signed-off-by: Allen.Ye <allen.ye@mediatek.com>
Pass bss->ctx instead of drv->ctx in order to avoid multiple reports for
the first bss. The first report would otherwise clear hapd->cca_color and
subsequent reports would cause the iface bss color to be set to 0.
In order to avoid any issues with cancellations, only overwrite the color
based on hapd->cca_color if it was actually set.
Fixes: 33c4dd26cd ("BSS coloring: Handle the collision and CCA events coming from the kernel")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A copy-paste issue in wpa_ft_bigtk_subelem() ended up encoding the IGTK
value instead of the BIGTK when providing the current BIGTK to the STA
during FT protocol. Fix this to use the correct key to avoid issues when
beacon protection is used with FT.
Fixes: 16889aff40 ("Add BIGTK KDE and subelement similarly to IGTK")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
QCA vendor extension is used for NDP setup. This defines the new
attributes QCA_WLAN_VENDOR_ATTR_NDP_CSIA_CAPABILITIES and
QCA_WLAN_VENDOR_ATTR_NDP_GTK_REQUIRED to support GTKSA, IGTKSA, and
BIGTKSA for NDP setup.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The set of protected elements in the FTE in Reassociation Response frame
is different for MLO. Count RSNE and RSNXE separately for each link.
This implementation uses the number of links for which a GTK was
provided which does not fully match the standard ("requested link") and
a more accurate implementation is likely needed, but that will require
some more complexity and state information.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Defragment the FTE if it was fragmented. This is needed for MLO when the
FTE in Reassociation Response frame might be longer than 255 octets to
include all the group keys for all the links.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Parse link id and station MLD address received from the driver in the
NL80211_CMD_NEW_STA event.
Set MLO information of the station to the sta_info and wpa_sm.
Co-authored-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add check to skip the STA mode specific MLO link channel switch handling
in AP mode. Commit 1b6f3b5850 ("MLD STA: Indicate per link channel
switch") added this indication only for STA mode.
Signed-off-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
Add support to parse association link id and MLD address from the
NL80211_CMD_UPDATE_OWE_INFO event.
Set MLO information of the station to the sta_info and wpa_sm.
Use station association link address for sending DH IE info to the
driver.
Signed-off-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
Use station association link address for sending SAE authentication
status to the driver in AP mode external authentication status.
Signed-off-by: Manaswini Paluri <quic_mpaluri@quicinc.com>
Extend QCA_WLAN_VENDOR_ATTR_CONFIG_OPTIMIZED_POWER_MANAGEMENT
attribute to support enum qca_wlan_vendor_opm_mode.
Add QCA vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_ITO and
QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_SPEC_WAKE to configure inactivity
timeout and speculative wake interval in User defined optimized
power save mode.
Signed-off-by: Vishal Miskin <quic_vmiskin@quicinc.com>
Verify that the operation succeeds before a debug print indicating that
it did. This was already done in most callers, so be more consistent and
do it here as well.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The second argument to memset() is only eight bits, so there is no point
in trying to set 0xffff values for an array of 16-bit fields. 0xff will
do the exact same thing without causing static analyzes warnings about
truncated value.
Fixes: 903e3a1e62 ("FILS: Fix maximum NSS calculation for FD frame")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
ideal_chan is NULL here, so it is not really valid to try to debug print
something from it due to the implied NULL pointer dereferencing.
Fixes: af0f60e7dd ("EHT: Calculate puncturing bitmap for ACS")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Check the ieee802_11_parse_elems() return code and do not proceed in
various cases if parsing failed. Previously, these cases would have been
allowed to continue by ignoring whatever might have followed in the IE
buffer after the first detected parsing failure. This is not really an
issue in practice, but it feels cleaner to explicitly stop when
receiving an invalid set of IEs.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Optimize the search for nonzero octets when checking for the need to
work around WPS M1 padding. The previous implementation was really
inefficient (O(n^2)) and while that was likely sufficiently fast for the
cases where the MMPDU size limit prevents long buffers (e.g., all P2P
Action frames), it might be able to take tens of seconds on low-end CPUs
with maximum length EAP-WSC messages during WPS provisioning. More
visibly, this was causing OSS-Fuzz to time out a test case with
unrealisticly long data (i.e., almost 10 times the maximum EAP-WSC
buffer length).
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=60039
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow the phase2_auth=2 parameter (in phase1 configuration item) to be
used with EAP-TTLS to require Phase 2 authentication. In practice, this
disables TLS session resumption since EAP-TTLS is defined to skip Phase
2 when resuming a session.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The previous PEAP client behavior allowed the server to skip Phase 2
authentication with the expectation that the server was authenticated
during Phase 1 through TLS server certificate validation. Various PEAP
specifications are not exactly clear on what the behavior on this front
is supposed to be and as such, this ended up being more flexible than
the TTLS/FAST/TEAP cases. However, this is not really ideal when
unfortunately common misconfiguration of PEAP is used in deployed
devices where the server trust root (ca_cert) is not configured or the
user has an easy option for allowing this validation step to be skipped.
Change the default PEAP client behavior to be to require Phase 2
authentication to be successfully completed for cases where TLS session
resumption is not used and the client certificate has not been
configured. Those two exceptions are the main cases where a deployed
authentication server might skip Phase 2 and as such, where a more
strict default behavior could result in undesired interoperability
issues. Requiring Phase 2 authentication will end up disabling TLS
session resumption automatically to avoid interoperability issues.
Allow Phase 2 authentication behavior to be configured with a new phase1
configuration parameter option:
'phase2_auth' option can be used to control Phase 2 (i.e., within TLS
tunnel) behavior for PEAP:
* 0 = do not require Phase 2 authentication
* 1 = require Phase 2 authentication when client certificate
(private_key/client_cert) is no used and TLS session resumption was
not used (default)
* 2 = require Phase 2 authentication in all cases
Signed-off-by: Jouni Malinen <j@w1.fi>
