Previously, 6 GHz Band Capability element was derived from HT and VHT
capabilities of the device. Removes such unnecessary dependency by
relying directly on the HE capability.
In addition, clean up the struct ieee80211_he_6ghz_band_cap definition
to use a 16-bit little endian field instead of two 8-bit fields to match
the definition in P802.11ax.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Move the FILS Public Key element and the FILS Key Confirmation element
to be separate IEs instead of being encapsulated within the SAE-PK
element. This is also removing the unnecessary length field for the
fixed-length EncryptedModifier.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This was clarified in the draft specification to not be a mandatory
requirement for the AP and STA to enforce, i.e., matching security level
is a recommendation for AP configuration rather than a protocol
requirement.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use value 2 to point to RFC 5480 which describes the explicit
indicatiotion of the public key being in compressed form.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is in preparation of implementation changes to check SAE-PK
password length more accurately based on the Sec value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new sae_commit_status and sae_pk_omit configuration parameters and
an extra key at the end of sae_password pk argument can be used to
override SAE-PK behavior for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define QCA vendor attribute in SET(GET)_WIFI_CONFIGURATION to
dynamically configure capabilities for dynamic bandwidth adjustment.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Define QCA vendor attribute in SET(GET)_WIFI_CONFIGURATION to
dynamically configure capabilities for channel width.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Add new QCA vendor attributes to configure RSNXE Used (FTE), ignore CSA,
and OCI frequency override with QCA vendor command
QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION for STA testbed role.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This maintains knowledge of whether H2E or PK was used as part of the
SAE authentication beyond the removal of temporary state needed during
that authentication. This makes it easier to use information about which
kind of SAE authentication was used at higher layer functionality.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
While this is not explicitly defined as the limit, lambda=8 (i.e., 9
characters with the added hyphen) is needed with Sec=5 to reach the
minimum required resistance to preimage attacks, so use this as an
implicit definition of the password length constraint.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Lambda >= 12 is needed with Sec = 2, so drop the shorter password
lengths in the sae_pk and module_wpa_supplicant test cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
While the current implementation forces these groups to be same, that is
not strictly speaking necessary and the correct group to use here is
K_AP, not the SAE authentication group.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds core SAE functionality for a new mode of using SAE with a
specially constructed password that contains a fingerprint for an AP
public key and that public key being used to validate an additional
signature in SAE confirm from the AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an attribute QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED
to get the response for the queried data.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new OCV-FAILURE control interface event to notify upper layers of
OCV validation issues. This commit adds this for SA Query processing in
AP mode.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make reporting of OCV validation failure reasons more flexible by
removing the fixed prefix from ocv_verify_tx_params() output in
ocv_errorstr so that the caller can use whatever prefix or encapsulation
that is most appropriate for each case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define QCA vendor attributes for SET(GET)_WIFI_CONFIGURATION to
dynamically configure capabilities for TX A-MSDU and RX A-MSDU.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Add a QCA vendor subcommand QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC
to add and delete TSPEC in STA mode.
The attributes defined in enum qca_wlan_vendor_attr_config_tspec
are used to encapsulate required information.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Add new QCA vendor attributes to configure misbehavior for PMF
protection for Management frames and to inject Disassociation frames.
These attributes are used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an attribute that can be used with
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION vendor command to
configure different PHY modes to the driver/firmware.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The VHT Operation Information subfield is conditonally present, so do
not hardcoded it in struct ieee80211_he_operation. These members of the
struct are not currently used, so these can be removed without impact to
functionality.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Defines IEEE P802.11ax/D6.0, 9.4.2.261 HE 6 GHz Band Capabilities
element and 6 GHz Operation Information field of HE Operation element
(IEEE P802.11ax/D6.0, Figure 9-787k).
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Use a shared wpa_alg_bip() function for this and fix the case in
nl_add_key() to cover all BIP algorithms. That fix does not change any
behavior since the function is not currently used with any BIP
algorithm, but it is better to avoid surprises should it ever be needed
with IGTK.
Signed-off-by: Jouni Malinen <j@w1.fi>
IGTK is the key that is used a BIP cipher. WPA_ALG_IGTK was the
historical name used for this enum value when only the AES-128-CMAC
based BIP algorithm was supported. Rename this to match the style used
with the other BIP options.
Signed-off-by: Jouni Malinen <j@w1.fi>
This file needs the EVP_PKEY_get0_EC_KEY() compatibility wrapper just
like other DPP source code files using this function.
Fixes: 21c612017b ("DPP: Move configurator backup into a separate source code file")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows DPP_AUTH_INIT to be used with tcp_addr=<dst> argument and
Configurator parameters to perform Configurator initiated DPP
provisioning over TCP. Similarly, DPP_CONTROLLER_START can now be used
to specify Configurator/Enrollee roles and extend Controller to work in
Enrollee role.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Recognize the Reconfig Announcement message type and handle it similarly
to the Presence Announcement in the Relay, i.e., send it to the first
Controller if the local Configurator does not have matching C-sign-key.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use the new struct dpp_authentication instance when setting Configurator
parameters for authentication exchange triggered by Presence
Announcement. conn->auth is NULL here and would cause dereferencing of a
NULL pointer if dpp_configurator_params is set.
Fixes: fa5143feb3 ("DPP2: Presence Announcement processing in Controller")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend Enrollee functionality to process Reconfig Authentication
Confirm message and start GAS client.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend Configurator functionality to sign a special Connector for
reconfiguration and reply with Reconfig Authentication Request frame
when Reconfig Announcement frame is received with a matching C-sign key
hash value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check if there is a matching Configurator and be ready to initiate
Reconfig Authentication (which itself is not included in this commit).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend DPP chirping mechanism to allow Reconfig Announcement frames to
be transmitted instead of the Presence Announcement frames. Add a new
wpa_supplicant control interface command "DPP_RECONFIG <network id>" to
initiate reconfiguration for a specific network profile.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Split ke derivation into two parts so that the previously used
internal-only PRK gets stored as the bk in the authentication state.
This new key will be needed for deriving additional keys with DPP R2.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This removes unnecessary allocations and simplifies the implementation
by not having to remember to free the cloned reference.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Fix a copy-paste error in parsing the version info.
Fixes: 7dd768c3ca ("DPP2: Version information in bootstrapping info URI")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the local supported version information into the bootstrapping
information (V=2 in the URI) and parse this from received URI.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Report MUD URL and bandSupport from config request if those optional
nodes are included. For now, these are mainly for testing purposes since
there is no mechanism to delay sending of config response.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When DPP v2 implementation is hardcoded to behave as v1 for testing
purposes, leave out the Protocol Version attribute form Authentication
Request instead of including it there with indication for v1.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This simplifies dpp_build_conf_obj_dpp() and makes it easier to share
the signing functionality for other purposes like reconfiguration where
the Configurator needs to sign a dppCon object for itself without
generating the encapsulating config object.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"SET dpp_version_override <ver>" can now be used to request
wpa_supplicant and hostapd to support a subset of DPP versions. In
practice, the only valid case for now is to fall back from DPP version 2
support to version 1 in builds that include CONFIG_DPP2=y.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Documentation of the return values for wpa_parse_vendor_specific() and
wpa_parse_generic() were not accurate and the parsing results from these
were not really handled appropriately. There is no point in calling
wpa_parse_vendor_specific() if wpa_parse_generic() recognizes a KDE. Not
that this would break anything in practice, but still, it looks
confusing.
The part about handling wpa_parse_vendor_specific() return value can, at
least in theory, break some cases where an unexpectedly short KDE/vendor
specific element were present and something would need to be recognized
after it. That does not really happen with any standard compliant
implementation and this is unlikely to cause any real harm, but it is
clearer to handle this more appropriately even for any theoretical case,
including misbehavior of a peer device.
Instead of stopping parsing on too short vendor specific element,
continue parsing the following KDEs/IEs. Skip the
wpa_parse_vendor_specific() call when a KDE has been recognized. Also
fix the return value documentation for wpa_parse_generic() and remove
the useless return value from wpa_parse_vendor_specific().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
EVP_PKEY_get0_EC_KEY() compatibility wrapper is used only within
CONFIG_DPP2 blocks, so define it with matching condition.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a build flag CONFIG_NO_TKIP=y to remove all TKIP functionality from
hostapd and wpa_supplicant builds. This disables use of TKIP as both the
pairwise and group cipher. The end result does not interoperate with a
WPA(v1)-only device or WPA+WPA2 mixed modes.
Signed-off-by: Disha Das <dishad@codeaurora.org>
Add an attribute QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FREQUENCY_2
for describing the secondary 80 MHz span of agile spectral scan.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Mark own bootstrap information as having been used in NFC negotiated
connection handover and do not accept non-mutual authentication when
processing Authentication Response from the peer when such bootstrapping
information is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Connector alone is not sufficient for authentication during
reconfiguration, so store the netAccessKey as well.
Fixes: e4eb009d98 ("DPP2: Add Connector and C-sign-key in psk/sae credentials for reconfig")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the Enrollee indicates support for DPP R2 or newer, add Connector and
C-sign-key in psk/sae credentials (i.e., cases where DPP AKM is not
enabled) for reconfiguration. Extend processing of such credentials in
wpa_supplicant network profile addition to handle this new case
correctly by not setting key_mgmt=DPP based on Connector being present,
but by looking at the actual akm value in the config object.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a driver interface event for Beacon frame protection failures.
Report such events over the control interface and send a
WNM-Notification Request frame to the AP as well.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
EVP_PKEY_get0_EC_KEY() was added in OpenSSL 1.1.0, so add a
compatibility wrapper for it when building with OpenSSL 1.0.2.
Fixes: c025c2eb59 ("DPP: DPPEnvelopedData generation for Configurator backup")
Fixes: 7d9e320054 ("DPP: Received Configurator backup processing")
Signed-off-by: Jouni Malinen <j@w1.fi>
Add definition for HE bit in neighbor report BSSID Information field
from IEEE P802.11ax/D6.0, 9.4.2.36 Neighbor Report element.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
This functionality was repeated for multiple different frames. Use a
shared helper function to avoid such duplication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process the received Presence Announcement frames in Controller. If a
matching bootstrapping entry for the peer is found, initiate DPP
authentication to complete provisioning of the Enrollee.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process the received Presence Announcement frames in AP/Relay. If a
matching bootstrapping entry for the peer is found in a local
Configurator, that Configurator is used. Otherwise, the frame is relayed
to the first configured Controller (if available).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process received Presence Announcement frames and initiate
Authentication exchange if matching information is available on the
Configurator.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wpa_supplicant control interface command "DPP_CHIRP own=<BI
ID> iter=<count>" to request chirping, i.e., sending of Presence
Announcement frames, to be started.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new identifier definitions for presence announcement,
reconfiguration, and certificate enrollment.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"DPP_BOOTSTRAP_SET <ID> <configurator parameters..>" can now be used to
set peer specific configurator parameters which will override any global
parameters from dpp_configurator_params.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a more convenient way of addressing cases where a
Configurator/Controller may store a large number of peer bootstrapping
information instances and may need to manage different configuration
parameters for each peer while operating as the Responder.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Set the global pointer and msg_ctx when allocating struct
dpp_authentication instead of needing to pass these to
dpp_set_configurator().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check whether the Transition Disable KDE is received from an
authenticated AP and if so, whether it contains valid indication for
disabling a transition mode. If that is the case, update the local
network profile by removing the less secure options.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the OUI Type and bitmap values for Transition Disable KDE. These
will be shared by both the AP and STA implementations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA_WLAN_VENDOR_CFR_NDPA_NDP_ALL in enum
qca_wlan_vendor_cfr_capture_type. This capture type requests all NDPA
NDP frames to be filtered.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The parameters that need to be applied are symmetric to those of VHT,
however the validation code needs to be tweaked to check the HE
capabilities.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Enhanced channel frequency response supports capturing of channel status
information based on RX. Define previous CFR as version 1 and enhanced
CFR as version 2. If target supports both versions, two versions can't
be enabled at same time. Extend attributes for enhanced CFR capture in
enum qca_wlan_vendor_peer_cfr_capture_attr.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add more hang reason codes for the hang reason in the
QCA_NL80211_VENDOR_SUBCMD_HANG events. This also introduces the
attribute QCA_WLAN_VENDOR_ATTR_HANG_REASON_DATA to carry the required
data for the respective hang reason. This data is expected to contain
the required dump to analyze the reason for the hang.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Some APs have managed to add two SSID elements into Beacon frames and
that used to result in picking the last one which had incorrect data in
the known examples of this misbehavior. Pick the first one to get the
correct SSID.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_parse_kde_ies(), i.e., the only caller to wpa_parse_generic(),
verifies that there is room for KDE Length field and pos[1] (that
length) octets of payload in the Key Data buffer. The PMKID KDE case
within wpa_parse_generic() was doing an unnecessary separate check for
there being room for the Length, OUI, and Data Type fields. This is
covered by the check in the calling function with the combination of
verifying that pos[1] is large enough to contain RSN_SELECTOR_LEN +
PMKID_LEN octets of payload.
This is confusing since no other KDE case was checking remaining full
buffer room within wpa_parse_generic(). Clean this up by removing the
unnecessary check from the PMKID KDE case so that all KDEs are handled
consistently.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_parse_generic() can now recognize the Key ID KDE that will be needed
to deliver the Key ID of the pairwise key when Extended Key ID is used.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
KEY_FLAG_MODIFY was initial added for the planned Extended Key ID
support with commit a919a26035 ("Introduce and add key_flag") and then
removed with commit 82eaa3e688 ("Remove the not yet needed
KEY_FLAG_MODIFY") to simplify commit e9e69221c1 ("Validity checking
function for key_flag API").
Add it again and update check_key_flag() accordingly.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Check whether an error is reported from any of the functions that could
in theory fail and if so, do not proceed with the partially filled SAE
commit buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
There was a copy-paste error in this code that would be adding the
connectorTemplate once that becomes available. In practice, this was not
reachable code, but anyway, this should be ready for potential addition
of connectorTemplate in the future.
Signed-off-by: Jouni Malinen <j@w1.fi>
The initial implementation of the PTK derivation workaround for
interoperability with older OWE implementations forced
WPA_KEY_MGMT_PSK_SHA256 to be used for all of PTK derivation. While that
is needed for selecting which hash algorithm to use, this was also
changing the length of the PTK components and by doing so, did not
actually address the backwards compatibility issue.
Fix this by forcing SHA256 as the hash algorithm in PTK derivation
without changing the PTK length calculation for OWE when
owe_ptk_workaround is enabled.
Fixes: 65a44e849a ("OWE: PTK derivation workaround in AP mode")
Fixes: 8b138d2826 ("OWE: PTK derivation workaround in STA mode")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add masks for each key type to define which flags can be combined and
add a helper function to validate key_flag values.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
I decided to drop KEY_FLAG_MODIFY instead of allowing flag combinations not
yet used in the code and will simply recreate it with the Extended Key
ID patches once we get there. For that reason I also did not renumber
the flags.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The commit a34ca59e (SAE: Allow SAE password to be configured separately
(STA)) added sae_password configuration option. We should also consider
sae_password in the wpa_config_write() function which stores the valid
network block details to an external database.
Fixes: a34ca59e4d ("SAE: Allow SAE password to be configured separately (STA)")
Signed-off-by: Sachin Shelke <sachin.shelke@nxp.com>
Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Add support for element defragmentation as defined in IEEE
P802.11-REVmd/D3.0, 10.28.12 (Element defragmentation).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
IEEE P802.11az/D2.0 renamed the FILS Wrapped Data element,
removing the FILS prefix. Change the code accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_ctrl.h can be installed separately with libwpa_client, so
utils/common.h won't be available to its users.
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Add an attribute QCA_WLAN_VENDOR_ATTR_SCAN_DWELL_TIME for specifying
dwell time in the QCA vendor scan command. This is a common value which
applies across all frequencies requested in the scan.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This attribute enables/disables the host driver to send roam reason
information in the Reassociation Request frame to the AP in the same
ESS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Couple of the attributes were defined with inconsistent prefix in the
name (missing "CONFIG_"). Fix these to use the common prefix for all
enum qca_wlan_vendor_attr_config values. Add defined values for the
incorrect names to avoid issues with existing users.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Rekeying a pairwise key using only keyid 0 (PTK0 rekey) has many broken
implementations and should be avoided when using or interacting with
one. The effects can be triggered by either end of the connection and
range from hardly noticeable disconnects over long connection freezes up
to leaking clear text MPDUs.
To allow affected users to mitigate the issues, add a new hostapd
configuration option "wpa_deny_ptk0_rekey" to replace all PTK0 rekeys
with disconnection. This requires the station to reassociate to get
connected again and as such, can result in connectivity issues as well.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The HE Operation field for BSS color consists of a disabled, a partial,
and 6 color bits. The original commit adding support for BSS color
considered this to be a u8. This commit changes this to the actual
bits/values.
This adds an explicit config parameter for the partial bit. The disabled
is set to 0 implicitly if a bss_color is defined.
Interoperability testing showed that stations will require a BSS color
to be set even if the feature is disabled. Hence the default color is 1
when none is defined inside the config file.
Signed-off-by: John Crispin <john@phrozen.org>
This commit adds new attributes for getting the Probe Response frame
IEs, Beacon frame IEs and the disconnection reason codes through
get_sta_info vendor command.
The host driver shall give this driver specific reason code through
the disconnection reason code attribute
QCA_WLAN_VENDOR_ATTR_GET_STA_DRIVER_DISCONNECT_REASON.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This acts as an event from the host driver to the user space to notify
the driver specific reason for a disconnection. The host driver
initiates the disconnection for various scenarios (beacon miss, Tx
Failures, gateway unreachability, etc.) and the reason codes from
cfg80211_disconnected() do not carry these driver specific reason codes.
Host drivers should trigger this event immediately prior to triggering
cfg80211_disconnected() to allow the user space to correlate the driver
specific reason code with the disconnect indication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This acts as a vendor event and is used to update the information
of a station from the driver to userspace.
Add an attribute for the driver to update the channels scanned in
the last connect/roam attempt.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This attribute aims to configure the STA to send the Beacon Report
Response with failure reason for the scenarios where the Beacon Report
Request cannot be handled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This ugly hack for being able to search for optional arguments with
space before them was quite inconvenient and unexpected. Clean this up
by handling this mess internally with a memory allocation and string
duplication if needed so that the users of wpa_supplicant control
interface do not need to care about such details.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
As qca_vendor.h alone can be included by other applications, define
macro BIT() in qca_vendor.h itself if not yet defined, e.g., by
including utils/common.h before qca_vendor.h.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This was not supposed to set the constructed bit in the header. Fix this
to avoid parsing issues with other ASN.1 DER parsers.
Fixes: c025c2eb59 ("DPP: DPPEnvelopedData generation for Configurator backup")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make Configurator provisioning require explicit conf parameter enabling
similarly to the previously used conf=ap-* and conf=sta-* cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This avoids unexpected behavior if GAS query fails and the Config
Response does not get processed at all. Previously, this could result in
configuration being assumed to be successful instead of failure when
Config Response object was not received at all. That could result in
undesired Config Result frame transmission with DPP Rel 2 and not
clearing the ongoing DPP session.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, unexpected Authentication Confirm messages were ignored in
cases where no Authentication Confirm message was expected at all, but
if this message was received twice in a state where it was expected, the
duplicated version was also processed. This resulted in unexpected
behavior when authentication result was processed multiple times (e.g.,
two instances of GAS client could have been started).
Fix this by checking auth->waiting_auth_conf before processing
Authetication Confirm. That boolean was already tracked, but it was used
only for other purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Only one peer-commit-scalar value was stored for a specific STA (i.e.,
one per MAC address) and that value got replaced when the next SAE
Authentication exchange was started. This ended up breaking the check
against re-use of peer-commit-scalar from an Accepted instance when
anti-clogging token was requested. The first SAE commit message (the one
without anti-clogging token) ended up overwriting the cached
peer-commit-scalar value while leaving that instance in Accepted state.
The second SAE commit message (with anti-clogging token) added ended up
getting rejected if it used the same value again (and re-use is expected
in this particular case where the value was not used in Accepted
instance).
Fix this by using a separate pointer for storing the peer-commit-scalar
value that was used in an Accepted instance. There is no need to
allocate memory for two values, i.e., it is sufficient to maintain
separate pointers to the value and move the stored value to the special
Accepted state pointer when moving to the Accepted state.
This fixes issues where a peer STA ends up running back-to-back SAE
authentication within couple of seconds, i.e., without hostapd timing
out the STA entry for a case where anti-clogging token is required.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit introduces additional stats to query through
QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds support for generating an encrypted backup of the local
Configurator information for the purpose of enrolling a new
Configurator. This includes all ASN.1 construction and data encryption,
but the configuration and connector template values in
dpp_build_conf_params() are not yet complete.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process the received DPPEnvelopedData when going through Configurator
provisioning as the Enrollee (the new Configurator). This parses the
message, derives the needed keys, and decrypts the Configurator
parameters. This commit stores the received information in
auth->conf_key_pkg, but the actually use of that information to create a
new Configurator instance will be handled in a separate commit.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
There is no need for the Protocol Version attribute in Authentication
Response if the peer is a DPP R1 device since such device would not know
how to use this attribute. To reduce risk for interoperability issues,
add this new attribute only if the peer included it in Authentication
Request.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an attribute QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY_FREQUENCY for
primary channel center frequency in the definition for Representative
Tx Power List (RTPL) list entry instance. This is required for 6 GHz
support, since the 6 GHz channel numbers overlap with existing 2.4 GHz
and 5 GHz channel numbers thus requiring frequency values to uniquely
identify channels.
Mark QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY as deprecated if both the
driver and user space application support 6 GHz. For backward
compatibility, QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY is still used if
either the driver or user space application or both do not support the
6 GHz band.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make the selected channel available for upper layer software to use,
e.g., when starting DPP listen operation during NFC negotiated
connection handover.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new control interface commands "DPP_NFC_HANDOVER_REQ own=<id>
uri=<URI>" and "DPP_NFC_HANDOVER_SEL own=<id> uri=<URI>" to support NFC
negotiated connection handover. These commands are used to report a DPP
URI received from a peer NFC Device in Handover Request and Handover
Select messages. The commands return peer bootstrapping information ID
or FAIL on failure. The returned ID is used similarly to any other
bootstrapping information to initiate DPP authentication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new dpp_gen_uri() helper function can be used to build the
bootstrapping URI from locally stored information. This can be used to
make it easier to update the URI, e.g., for NFC negotiated connection
handover cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit introduces the vendor event
QCA_NL80211_VENDOR_SUBCMD_REQUEST_SAR_LIMITS_EVENT.
Host drivers can request user space application to set SAR power
limits with this event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new QCA vendor attribute to set thermal level to the driver from
userspace. The driver/firmware takes actions requested by userspace to
mitigate high temperature such as throttling TX etc. The driver may
choose the level of throttling and other actions for various thermal
levels set by userspace.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previous implementation was hardcoding use of SHA256 PMK-to-PTK
derivation for all groups. Replace that with hash algorithm selection
based on the length of the prime similarly to the way this was done for
other derivation steps in OWE.
This breaks backwards compatibility when using group 20 or 21; group 19
behavior remains same.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous commit had a rebasing issue that ended up covering only the
center_segment0 != 0 case. These were supposed to apply for all 6 GHz
band cases.
Fixes: 0bfc04b8d0 ("Do not enable HT/VHT when operating in 6 GHz band")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE P802.11-REVmd was modified to use a container IE for anti-clogging
token whenver H2E is used so that parsing of the SAE Authentication
frames can be simplified.
See this document for more details of the approved changes:
https://mentor.ieee.org/802.11/dcn/19/11-19-2154-02-000m-sae-anti-clogging-token.docx
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update the documentation with values to be sent for seg0 and seg1 fields
in external ACS result event for 20 MHz, 40 MHz, 80 MHz, 160 MHz, and
80+80 MHz channels. These values match the changes done to definitions
of seg0 and seg1 fields in the IEEE 802.11 standard.
This vendor command had not previously been documented in this level of
detail and had not actually been used for the only case that could have
two different interpretation (160 MHz) based on which version of IEEE
802.11 standard is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the new set_key() parameter "key_flag" to provide more specific
description of what type of a key is being configured. This is needed to
be able to add support for "Extended Key ID for Individually Addressed
Frames" from IEEE Std 802.11-2016. In addition, this may be used to
replace the set_tx boolean eventually once all the driver wrappers have
moved to using the new key_flag.
The following flag are defined:
KEY_FLAG_MODIFY
Set when an already installed key must be updated.
So far the only use-case is changing RX/TX status of installed
keys. Must not be set when deleting a key.
KEY_FLAG_DEFAULT
Set when the key is also a default key. Must not be set when
deleting a key. (This is the replacement for set_tx.)
KEY_FLAG_RX
The key is valid for RX. Must not be set when deleting a key.
KEY_FLAG_TX
The key is valid for TX. Must not be set when deleting a key.
KEY_FLAG_GROUP
The key is a broadcast or group key.
KEY_FLAG_PAIRWISE
The key is a pairwise key.
KEY_FLAG_PMK
The key is a Pairwise Master Key (PMK).
Predefined and needed flag combinations so far are:
KEY_FLAG_GROUP_RX_TX
WEP key not used as default key (yet).
KEY_FLAG_GROUP_RX_TX_DEFAULT
Default WEP or WPA-NONE key.
KEY_FLAG_GROUP_RX
GTK key valid for RX only.
KEY_FLAG_GROUP_TX_DEFAULT
GTK key valid for TX only, immediately taking over TX.
KEY_FLAG_PAIRWISE_RX_TX
Pairwise key immediately becoming the active pairwise key.
KEY_FLAG_PAIRWISE_RX
Pairwise key not yet valid for TX. (Only usable with Extended Key ID
support.)
KEY_FLAG_PAIRWISE_RX_TX_MODIFY
Enable TX for a pairwise key installed with KEY_FLAG_PAIRWISE_RX.
KEY_FLAG_RX_TX
Not a valid standalone key type and can only used in combination
with other flags to mark a key for RX/TX.
This commit is not changing any functionality. It just adds the new
key_flag to all hostapd/wpa_supplicant set_key() functions without using
it, yet.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
According to IEEE P802.11ax/D6.0, 11.1.4.3.4 (Criteria for sending a
response), AP should answer Probe Request frames if either SSID or Short
SSID matches. Implement this part of the Short SSID use for the BSS (the
collocated 6 GHz BSS case is not covered in this commit).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Move this implementation from check_40mhz_2g4() into a new helper
function check_bss_coex_40mhz function() so that it can be used in the
station mode case as well as the previously used AP mode case.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
WPS_EVENT_CANCEL is added to indicate cancellation of a WPS operation
for any reason in hostapd/wpa_supplicant.
WPS_EVENT_PIN_ACTIVE is added to indicate when a PIN operation is
triggered in wpa_supplicant.
Signed-off-by: Veli Demirel <veli.demirel@airties.com>
Signed-off-by: Bilal Hatipoglu <bilal.hatipoglu@airties.com>
The case where the old RSNE included one or more PMKIDs and that RSNE
was followed by another IE was handled incorrectly since the
os_memmove() to move the end of the buffer when removing old PMKIDs was
stopping copying at the end of the RSNE, not the end of the IE buffer.
This could result in corrupting the IE that followed the RSNE. In
practice, this broke FT-SAE with H2E by corrupting the RSNXE that is in
the buffer after the RSNE.
Fix this by copying the full end of the buffer (i.e., including the
following RSNXE in the visible error case) when removing the old PMKIDs.
Signed-off-by: Jouni Malinen <j@w1.fi>
Fix a memory leak exposed by the dpp_own_config_sign_fail test.
Fixes: 52d469de11 ("DPP2: Support multiple Config Objects in Enrollee")
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Add a QCA vendor subcommand QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO with
attributes defined in enum qca_wlan_vendor_attr_get_sta to get
information for a BSS in STA mode or for a peer STA in AP mode. This
vendor sub command can be used to get STA information from the driver to
userspace. The attributes defined in enum
qca_wlan_vendor_attr_get_sta_info are used to encapsulate required
information.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Use op_class to derive channel width for the operating channel when
op_class is configured by the user in both fixed channel and ACS cases.
We can avoid using ht_capab field to derive channel width especially in
the 6 GHz band in which only HE is supported.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Only HE mode is allowed in the 6 GHz band hence do not enable HT/VHT
even if they are configured by the user.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support to exclude non-PSC 6 GHz channels from the input frequency
list to ACS. The new acs_exclude_6ghz_non_psc=1 parameter can be used by
6 GHz only APs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Using the channel parameter for validating allowed channel combinations
is not scalable to add 6 GHz support in the future since channel numbers
are duplicated between 2.4 GHz / 5 GHz bands and 6 GHz band. Hence use
frequency field for all channel combination validation steps done before
starting AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The 5 GHz channels are stored in one hw_features set with mode
HOSTAPD_MODE_IEEE80211A while the 6 GHz channels will need to stored in
a separate hw_features set (but with same mode HOSTAPD_MODE_IEEE80211A)
due to possibility of different HE capabilities being available between
the 5 GHz and 6 GHz bands.
Search through all hw_features sets whose mode is same as the input mode
while finding channel corresponding to the input frequency in
hw_get_channel_freq().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update new channels in Channel Bonding (CB2 ... CB4) in the 60 GHz band
for different regulatory regions according to the latest draft amendment
IEEE P802.11ay/D5.0.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Add EDMG bandwidth to CHANWIDTH_ defines.
Update API ieee80211_freq_to_channel_ext() to support EDMG bandwidth
for EDMG channels.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
The netRole enum is more generic and can be extended to include new
roles (e.g., Configurator) more easily.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd and wpa_supplicant DPP implementation to allow the
bootstrapping URI to be generated for and parsed from an NFC Tag with an
NFC URI Record. This is similar to the way the bootstrapping URI is used
with QR Code for unidirectional authentication.
The DPP_BOOTSTRAP_GEN command uses "type=nfc-uri" to request the URI to
be assigned for NFC URI Record. In practice, the URI is generated
identically to the QR Code case, but the internal entry maintains the
NFC-URI type.
A new command "DPP_NFC_URI <uri>" can now be used to parse the URI read
from an NFC Tag with the NFC URI Record. This is similar to the
DPP_QR_CODE command.
Other commands (mainly, DPP_LISTEN and DPP_AUTH_INIT) are used for NFC
URI in the same way as they are used for QR Code.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows Configurator to be configured to use the ssid64 option in
the discovery object for a station Enrollee.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The discovery object is now allowed to use either the UTF-8 encoded
string ssid or base64url encoded ssid64.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow any pointer to be used as source for encoding and use char * as
the return value from encoding and input value for decoding to reduce
number of type casts needed in the callers.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow any pointer to be used as source for encoding and use char * as
the return value from encoding and input value for decoding to reduce
number of type casts needed in the callers.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
There is no use case for adding padding into the base64url encoded
strings, so remove the unneeded add_pad argument that was hardcoded to 0
in all callers.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The UTF-8 encoded ssid string was replaced with base64url encoded ssid64
string, so update the implementation to match.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
To config BT coex chain mode, add a new QCA sub command
QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE.
This new command has two attributes:
1. QCA_VENDOR_ATTR_COEX_BTC_CHAIN_MODE: u32 attribute. Indicates the
BT coex chain mode, are 32-bit values from enum qca_btc_chain_mode.
2. QCA_VENDOR_ATTR_COEX_BTC_CHAIN_MODE_RESTART: flag attribute.
If set, vdev should be restarted once BT coex chain mode is updated.
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
The QCA_NL80211_VENDOR_SUBCMD_OEM_DATA command was previously defined
only to pass data blobs from user space to kernel (application to
firmware) but there was no mechanism to send the data blobs from
firmware to application. Extend this to define use of the same
subcommand and attributes as vendor events.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Remove support for performing full sqrt(), i.e., only support curves
that use prime with p = 3 mod 4. In practice, this drops only group 26
with SAE H2E. This seems acceptable since there does not seem to be any
strong use case for that group taken into account the limits being
placed on acceptable prime lengths.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Protect RSNXE, if present, in FT Reassociation Request/Response frames.
This is needed for SAE H2E with FT.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use a single struct definition and a single shared implementation for
parsing EAPOL-Key KDEs and IEs instead of maintaining more or less
identical functionality separately for wpa_supplicant and hostapd.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor subcommand QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE with
attributes qca_wlan_vendor_attr_add_sta_node_params to add STA peer
entries in AP mode. This vendor sub command is used in FT roaming
scenario to send STA node information from application/service to
driver/firmware. The attributes defined in enum
qca_wlan_vendor_attr_add_sta_node_params are used to deliver the
parameters.
Signed-off-by: Shiva Sankar Gajula <sgajula@codeaurora.org>
The OEM data binary blobs from application/service will be routed to the
appropriate device based on this attribute value. This optional
attribute is used to specify whether the device type is virtual or
physical. This attribute can be omitted when the command is for a
virtual device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Some chipsets don't have the capability to run agile spectral scan with
160/80+80 MHz modes. Add separate agile spectral scanning capability
flags for 160, 80+80, and non-160 MHz modes to cover such cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When operating on the 6 GHz band, add 6 GHz Operation Information inside
the HE Operation element and don't publish HT/VHT IEs.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
- Replace HOSTAPD_MODE_IEEE80211AX mode checks with is_6ghz_op_class()
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Add support for new hardware mode for 6 GHz band. 6 GHz operation is
defined in IEEE P802.11ax/D4.3. 6 GHz band adds global operating classes
131-135 that define channels in frequency range from 5940 MHz to 7105
MHz.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
- Remove HOSTAPD_MODE_IEEE80211AX mode
- Replace check for HOSTAPD_MODE_IEEE80211AX with is_6ghz_freq()
- Move center_idx_to_bw_6ghz() to ieee802_11_common.c file
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
These are the defined values/identifiers for SAE hash-to-element
mechanism from IEEE P802.11-REVmd/D3.0.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The logic for displaying the message about no configuration being
available for the Enrollee was reversed when support for multiple Config
Objects was added. This was supposed to be shown only if the first
Config Object fails (i.e., when no configuration is available); not when
second attempt fails (since the first one had already been successful in
that case).
Fixes: 7eb06a3369 ("DPP2: Allow multiple Config Objects to be build on Configurator")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new use_akm_selector=1 value to Configurator parameters can now be
used to request a list of AKM suite selectors to be used in the
Configuration Object if the Enrollee supports version 2 or newer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process all received DPP Configuration Object attributes from
Configuration Result in Enrollee STA case. If wpa_supplicant is
configured to add networks automatically, this results in one network
being added for each included Configuration Object.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Special @CONF-OBJ-SEP@ string can now be used as a DPP configuration
string value to split the string into two different components to
configure two Config Objects for an Enrollee.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Go through the received bandSupport JSON array and print its contents in
the debug log. This information might be exposed to upper layer
configuration generation/use somehow in the future.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new hostapd and wpa_supplicant configuration parameters dpp_name and
dpp_mud_url can now be used to set a specific name and MUD URL for the
Enrollee to use in the Configuration Request. dpp_name replaces the
previously hardcoded "Test" string (which is still the default if an
explicit configuration entry is not included). dpp_mud_url can
optionally be used to add a MUD URL to describe the Enrollee device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
A new argument to the DPP_AUTH_INIT command (conn_status=1) can now be
used to set Configurator to request a station Enrollee to report
connection result after a successfully completed provisioning step. If
the peer supports this, the DPP-CONF-SENT event indicates this with a
new argument (wait_conn_status=1) and the Configurator remains waiting
for the connection result for up to 16 seconds.
Once the Enrollee reports the result, a new DPP-CONN-STATUS-RESULT event
is generated with arguments result, ssid, and channel_list indicating
what the Enrollee reported. result=0 means success while non-zero codes
are for various error cases as specified in the DPP tech spec. If no
report is received from the Enrollee, the event with "timeout" argument
is generated locally.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is more consistent with the use of CONFIG_DPP2 since the
Configuration Result message is sent only when using version 2 or newer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If only one of the allocations fails, the successful allocation needs to
be freed on the error path.
Fixes: 22f90b32f1 ("DPP2: Configuration Result message generation and processing")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous support in the 60 GHz band was for channels 1-4.
Add support for channels 5 and 6.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Update the documentation of QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST
to make it a nested attribute to carry frequencies of type u32.
This is to be in sync with the nl80211 attribute
NL80211_ATTR_SCAN_FREQUENCIES.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Hardcode this to be defined and remove the separate build options for
PMF since this functionality is needed with large number of newer
protocol extensions and is also something that should be enabled in all
WPA2/WPA3 networks.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set the max value of optional bytes inside the data structure. This
requires us to calculate the actually used size when copying the
HE capabilities and generating the IE.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Track PMK-R0/PMK-R0-Name from the initial mobility domain association
and derive PMK-R1/PTK when the station uses FT protocol. This allows
frames from additional roaming cases to be decrypted.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If FT over-the-DS case is enforced through the "FT_DS <BSSID>" control
interface command, the PMF capability check during BSS selection is not
used and that could have allowed PMF to be disabled in the over-the-DS
case even if the local network profile mandated use of PMF. Check
against this explicitly to avoid unexpected cases if the APs within the
same mobility domain are not configured consistently.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is not used only with FT, so make the comments less confusing and
include the function in all builds to make it available for
non-FT/non-FILS builds.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add vendor command QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT
and attribute qca_wlan_vendor_attr_avoid_frequency_ext to send structured
avoid frequency data.
This new command is alternative to existing command
QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY since existing command is
using stream of bytes instead of structured data using vendor attributes.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
As a part of P802.11ax amendment, 6 GHz band operation is added.
Since the 6 GHz channel numbers are overlapping with existing 2.4 GHz
and 5 GHz channel numbers, use frequency to identify unique channel
operation instead of channel number. Channel frequency is unique across
bands.
In the existing QCA vendor interface, wherever missing, add frequency
attributes to identify unique channel operation. In addition, add
comments to document some of the previously missed attributes/values.
Note: If both channel and frequency attributes are present in vendor
command/event and
(a) If both the driver and user-space application supports 6 GHz band
then channel related attributes are deprecated and use frequency
attributes.
(b) If either driver or user-space application or both doesn't
support 6 GHz band then use channel attributes.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Add QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL attribute in
enum qca_wlan_vendor_attr_sap_config to use with vendor command
QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG.
This new attribute is used to restart AP on given channel.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Add a QCA vendor sub command QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY
with attributes enum qca_wlan_vendor_attr_acs_config and
enum qca_acs_dfs_mode to configure ACS policy.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
This enhances the existing vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM
with the following configurations:
1. Set/get/clear roam control
2. Set/get the channels on which the roaming has to be triggered.
3. Set/get the roam scan period.
4. Configure the triggers for roaming.
5. Configure the candidate selection criteria.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
qca_wlan_vendor_attr_roam_subcmd is an enum associated with the
attribute QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD. It represents different
sub command values and these are not the attributes. Hence, rename the
enum to qca_wlan_vendor_roaming_subcmd. Accordingly, the members of this
enum are also renamed to suite the usage.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update the version number for the build and also add the ChangeLog
entries for both hostapd and wpa_supplicant to describe main changes
between v2.7 and v2.8.
Signed-off-by: Jouni Malinen <j@w1.fi>
The KCK, PMK, and PMKID derivation fix broke SAE key derivation for all
FFC groups. Fix that by setting sae->tmp->order_len for FFC groups (it
was only set for ECC groups).
Fixes: ac734a342e ("SAE: Fix KCK, PMK, and PMKID derivation for groups 22, 23, 24")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This replaces the separately implemented ECDH operations with a single
helper function to avoid code duplication. In addition, this introduces
a workaround for strange OpenSSL behavior where the first
EVP_PKEY_derive(NULL) call to learn the size of the output shared secret
returns unexpectedly large buffer (72 octets when expected 32 octets for
group 19). It is not known what is causing this, but such behavior seems
to be showing up every now and then at least when running hwsim test
cases under UML and apparently mainly (only?) in the sigma_dut
controller cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2016 is not exactly clear on the encoding of the bit
string that is needed for KCK, PMK, and PMKID derivation, but it seems
to make most sense to encode the (commit-scalar + peer-commit-scalar)
mod r part as a bit string by zero padding it from left to the length of
the order (in full octets).
The previous implementation used the length of the prime (in full
octets). This would work for KCK/PMK, but this results in deriving all
zero PMKIDs for the groups where the size of the order is smaller than
the size of the prime. This is the case for groups 22, 23, and 24.
However, those groups have been marked as being unsuitable for use with
SAE, so this fix should not really have a practical impact anymore.
Anyway, better fix it and document this clearly in the implementation
taken into account the unclarity of the standard in this area.
Signed-off-by: Jouni Malinen <j@w1.fi>
Disable groups that use Brainpool curves for now since they leak more
timing information due to the prime not being close to a power of two.
This removes use of groups 28, 29, and 30 from SAE and EAP-pwd.
Signed-off-by: Jouni Malinen <j@w1.fi>
These SAE, OWE, DPP, and OSEN AKM suite selectors were covered in the
reverse conversion in rsn_key_mgmt_to_bitfield(), but were missing from
wpa_akm_to_suite(). Add them to make AKM suite selector reporting more
accurate in RADIUS Accounting messages (and future users of this
function).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use a shared function to determine the k parameter, i.e., the minimum
number of iterations of the PWE derivation loop, for SAE and EAP-pwd.
This makes it easier to fine-tune the parameter based on the negotiated
group, if desired.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add attributes QCA_WLAN_VENDOR_ATTR_CONFIG_ELNA_BYPASS under
the enum qca_wlan_vendor_attr_config to support set and get
the ELNA bypass.
Signed-off-by: Paul Zhang <paulz@codeaurora.org>
Add a new vendor attribute QCA_WLAN_VENDOR_ATTR_DISCONNECT_IES
to configure disconnect IEs to the driver. Driver shall fill
these IEs in disassoc/deauth frame.
These IEs are expected to be considered only for the next
immediate disconnection (disassoc/deauth frame) originated by
the DUT, irrespective of the entity (user space/driver/firmware)
triggering the disconnection.
The host drivers are not expected to use the IEs set through
this interface for further disconnections after the first immediate
disconnection initiated post the configuration.
If the IEs are also updated through cfg80211 interface (after the
enhancement to cfg80211_disconnect), host driver is expected to
take the union of IEs from both of these interfaces and send in
further disassoc/deauth frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor sub command QCA_NL80211_VENDOR_SUBCMD_OEM_DATA
with attributes qca_wlan_vendor_attr_oem_data_params to support
OEM data. It is used to send OEM data binary blobs from
application/service to firmware. The attributes defined in enum
qca_wlan_vendor_attr_oem_data_params are used to deliver the
parameters.
Signed-off-by: Paul Zhang <paulz@codeaurora.org>
This reduces differences in timing and memory access within the
hunting-and-pecking loop for ECC groups that have a prime that is not
close to a power of two (e.g., Brainpool curves).
Signed-off-by: Jouni Malinen <j@w1.fi>
The driver automatically starts beacon reporting if it pauses the beacon
reporting for any reason other than disconnection. In specific cases,
userspace may not want the beacon reporting to be automatically resumed
after a pause. Add interface support for userspace to specify driver not
to start beacon reporting automatically after a pause.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the following vendor attributes under the enum
qca_wlan_vendor_attr_spectral_scan to support the configuration of
Spectral DMA debug.
1. QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_RING_DEBUG
Enable/disable debug of the Spectral DMA ring
2. QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_BUFFER_DEBUG
Enable/disable debug of the Spectral DMA buffers
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
