In order to handle regulatory domain requests, crda needs to be
installed on the host, but we also need to install a uevent helper in
the VM so that it gets executed (since we don't run udev).
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Some hw modes (e.g., 11b and 11g) contain the same frequencies,
causing the supp_freqs array to be populated with redundant entries.
Check for the existence of the freq before adding it.
Signed-hostap: Eliad Peller <eliad@wizery.com>
Stopping bgscan on any state other than COMPLETED results
in bgscan reset (stop + start) on every rekeying operation.
Signed-hostap: Eliad Peller <eliad@wizery.com>
This verifies that QoS Map configuration and update can be completed.
Actual QoS mapping for Data frames within mac80211/cfg80211 is not yet
verified.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Do not assume the driver supports QoS Mapping, but instead, advertise
support for this only if CONFIG_INTERWORKING is defined and driver
indicates support for configuring QoS Map.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The driver_nl80211.c changes are needed to avoid compiler warnings
with two frequency attributes pointing to the same value.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 202dec2a94 introduced a never
ending loop for a case where a single wpa_supplicant process is used
with multiple radios. Fix this by advancing the iface pointer properly
to the next interface in the loop until a NULL pointer is hit.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If more BSSes are added in config file than are supported by the driver,
segmentation fault can appear. For this case, the interface_added flag
needs to be cleared if adding a new BSS fails.
Signed-hostap: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Until now DFS was simply restarting the AP when radar was detected. Now
CSA is used to perform smooth switch to the new channel. Stations not
supporting CSA will behave as before.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
This is needed for AP CSA. Since CSA must happen immediately after radar
is detected there's no time to perform CAC. Thus, radar channels must be
disabled when looking for a new channel to escape to after a radar is
detected.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Adds support for VHT by parsing bandwidth and center_freq{1,2}.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Just the usual, with a new function os_reltime_initialized()
thrown in that checks whether time has ever been retrieved
(time can't be completely zero).
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This helper functions checks whether a given entry has expired,
given the last active timestamp, the current time, and a timeout.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on priority, remove the connection with least priority whenever
a frequency conflict is detected.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
This field allows adds enough information into the P2P-DEVICE-FOUND
events to figure out if the peer supports Wi-Fi Display.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
If there's code coverage analysis data, copy it out of the VM
to be able to analyse it later. Also add a description to the
README file about how to use it.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Allow addition static and shared libraries to be specified from the
eap_proxy_*.mk file for Android build. In addition use $(LOCAL_PATH) as
a prefix for that Android makefile part.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These were not really used in practice and better quality test cases for
concurrent P2P operations are now available in tests_p2p_concurrency.py
using the standard test framework design. Remove the special concurrent
option for start.sh and the run-all.sh concurrent and
concurrent-valgrind operations to clean up scripts.
Signed-hostap: Jouni Malinen <j@w1.fi>
struct wpa_radio is used as a shared data structure between all struct
wpa_supplicant instances that share the same physical radio.
Signed-hostap: Jouni Malinen <j@w1.fi>
Allow another EAP method to be tried if one of the enabled methods
fails. If all the remaining methods fail, reject connection by adding a
new METHOD_REQUEST -> FAILURE transition. Previously, this case resulted
in the state machine trying to send a message when none was available
and then waiting for a following event until timeout.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is possible for the authentication server to be configured with a
PKCS #12 file that includes a private key, a server certificate, and a
CA certificate. This combination could result in server_cert and ca_cert
parameters not being present and that should still result in TLS context
getting initialized.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was possible to configure hostapd in a way that could try to
initialize a TLS-based EAP method even when TLS library context was not
initialized (e.g., due to not configuring server or CA certificate).
Such a case could potentially result in NULL pointer dereference in the
TLS library, so check for this condition and reject EAP method
initialization.
Signed-hostap: Jouni Malinen <j@w1.fi>
This extends P2P test coverage to include the case of separate group
interface use with autonomous GO and group formation through GO
negotiation.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 390e489c0d extended hostapd BSS
interface removal capabilities. However, it ended up causing a
regression in wpa_supplicant P2P group interface handling. That P2P
group interface is removed through another driver_nl80211.c BSS context
and as such, the bss->added_if is not set. Fix this by verifying whether
the request is for another ifindex and if so, removing the interface
even if added_if is not marked.
Signed-hostap: Jouni Malinen <j@w1.fi>
An INTERFACE_DISABLED event received on an interface that is
currently operating a P2P GO means that the group session ended.
In such a case, if the interface was dynamically added remove it, and
if not, remove all the network blocks that are temporary, assuming
that if needed a new session will be started by an external entity.
The use case was triggering rfkill (both SW and HW). This case popped up
as part of a testing cycle, where after a toggle in the rfkill state,
the result was that the interface was not deleted, but on the other hand
the wpa_supplicant did not configure the kernel to re-start the AP
functionality again.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Some non-mac80211 drivers, such as ath6kl, support STA inactivity timer
in firmware and may not provide connected stations' idle time to the
userspace. If the driver indicates support for offloaded operation, do
not start the inactivity timer in the hostapd.
Signed-hostap: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
On scan results event if a concurrent P2P scan was triggered previously,
scan results processing is canceled, p2p_find executed, and a new sta
scan is triggered (pending scan). However, this new sta scan does not
restore the scan_req value of the previous scan (whose scan result has
been canceled).
If we are currently connected to an AP and use ap_scan=2, the new
triggered scan will cause an associtation-without-scan in
wpa_supplicant_scan:
(ap_scan == 2 & scan_req != MANUAL_SCAN_REQ)
=> wpa_supplicant_assoc_try()
causing an association error and a disconnection.
This patch fixes this issue by restoring the previous scan_req value.
Signed-off-by: Loic Poulain <loicx.poulain@intel.com>
struct beacon_data contains a lot of pointers. Make sure it gets cleared
to zero if hostapd_build_beacon_data() gets called from a path that does
not clear the structure first.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
