There may be cases where multiple BSS entries for a single BSSID are in
the table. This is mostly in automated test cases due to the AP
configuration changes, but something similar could potentially happen as
a corner case in more realistic networks, too, e.g., when an AP changes
its operating channel. Make network selection more robust by trying to
find the exact BSS entry instead of any BSS entry with a matching BSSID
when storing GAS/ANQP response.
Signed-hostap: Jouni Malinen <j@w1.fi>
Stopping the AP first was not ideal for the test cases since it could
result in wpa_supplicant trying to connect back and start a scan at the
end of a test case and cause problems for the following test case that
tried to scan in the beginning while the previously started scan was
still in progress.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some extended capabilities (I'm currently interested in "Operating Mode
Notification" for VHT) are implemented by the kernel driver and exported
in nl80211. Use these in hostapd/wpa_supplicant.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This is mainly for testing purposes where it is convenient to have an
easy way of getting wpa_supplicant state cleared between test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
If WPS provisioning step is completed with an AP that is in WPS
configured state, we can skip a second scan after the provisioning step
since the AP is unlikely to change its configuration in such a case.
This can speed up WPS connection a bit by removing an unneeded scan.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Do not print the potentially long list of passed test cases. In case of
failure(s), make sure the failed test list is the last item in the
report.
Signed-hostap: Jouni Malinen <j@w1.fi>
The WPS tests are more prone to fail if scan results from the previous
test cases are allowed to remain in the wpa_supplicant BSS table during
the consecutive test since the test setup uses the same BSSID for the
test APs that change their configuration. Avoid these mostly bogus
issues by enforcing wpa_supplicant to drop and ignore old scan results
during the WPS test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to configure wpa_supplicant to ignore old scan results
from the driver cache in cases where such results were not updated after
the scan trigger from wpa_supplicant. This can be useful in some cases
where the driver may cache information for a significant time and the AP
configuration is changing. Many such cases are for testing scripts, but
this could potentially be useful for some WPS use cases, too.
Signed-hostap: Jouni Malinen <j@w1.fi>
The after_wps counter could have potentially be left in its old non-zero
value in some WPS sequences which could result in a single-channel scan
being used based on obsolete information. Clear after_wps in
wpas_wps_reassoc() to make sure this does not happen.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the AP (P2P GO) has changes its channel of SSID recently, the BSS
table may have multiple entries for a BSSID. Select the one which was
most recently updated for WPS/P2P operations in such case to increase
the likelihood of using current information.
Signed-hostap: Jouni Malinen <j@w1.fi>
This removes the unnecessary separation of P2P (no hostapd) and AP
tests. The same scripts can be used to prepare for these tests and to
execute the tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new wps_independent=1 configuration parameter can be used to remove
interfaces from the shared hostapd process WPS control (i.e., to apply
WPS operations only to a subset of interfaces instead of all).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows WPS to update AP configuration in the case no hostapd
configuration file is used (i.e., dynamic configuration through the
control interface).
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of allocating a new message and then moving that into
the message being built, use nla_nest_start() and put the data
into the message directly.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
P2P_PROV_DISC fails if the peer is not fully discovered and the previous
version of the test cases did not force this (i.e., it could have
started PD just based on having seen a Probe Request frame from the
peer).
Signed-hostap: Jouni Malinen <j@w1.fi>
As per P2P specification v1.2: "The P2P Group Info attribute shall be
omitted if there are zero connected P2P Clients."
Do not add the attribute if there are not connected peers.
Signed-hostap: Chaitanya T K <chaitanya.mgit@gmail.com>
When the OS is out of random bytes in SM_STATE(WPA_PTK, AUTHENTICATION2)
in ap/wpa_auth.c, hostapd sends the sm to state DISCONNECT without
clearing ReAuthenticationRequest, resulting in an infinite loop.
Clearing sm->ReAuthenticationRequest using gdb fixes the running hostapd
instance for me. Also sm->Disconnect = TRUE should be used instead of
wpa_sta_disconnect() to make sure that the incomplete ANonce does not
get used.
Fix this issue by resetting sm->ReAuthenticationRequest even if the STA
gets disconnected and use sm->Disconnect instead of
wpa_sta_disconnect().
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
A non-HT capable AP on any channel could have triggered us to enable
protection regardless of own operating channel if the driver delivered
Beacon frames from other channels. The channel detection in ap_list is
not exactly ideal, but most cases can be handled by checking ap->channel
against the currently configured channel (or secondary channel in case
of HT40).
Signed-hostap: Jouni Malinen <j@w1.fi>
This iter_next/iter_prev pointers were not really used for anything, so
get rid of the unnecessary complexity in the AP list maintenance.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 6b56cc2d97 added a possible call to
p2p_reset_pending_pd() prior to checking config_methods match between
our request and peer response. That reset call could clear
dev->req_config_methods and as such, result in unexpected
P2P-PROV-DISC-FAILURE report here even in cases where the peer accepts
the provision discovery. Fix this by using a local copy of the
req_config_methods variable.
Signed-hostap: Jouni Malinen <j@w1.fi>
Select the BSS entry based on BSSID,SSID pairs instead of just BSSID to
avoid selecting an unexpected SSID for the ROAM command.
Signed-hostap: Jouni Malinen <j@w1.fi>
buildbot seems to be running with more limited umask by default and that
prevented the hostapd per-interface socket from being accessed.
Signed-hostap: Jouni Malinen <j@w1.fi>
