This allows external applications to get event indication for Probe
Request frames. Extend ctrl iface cmd "ATTACH" to enable this event on
per-request basis. For example, user has to send ctrl iface cmd "ATTACH
probe_rx_events=1" to enable the Probe Request frame events.
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
Previous implementation did not handle number of sequences correctly.
Make sure the iteration continues in both unicast and broadcast cases
until the five attempts have been made. In addition, improve timing by
checking 10 second time from the beginning of each iteration round and
not the last channel on which the Auth Req frame has been transmitted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the Authentication Request frame was retried after 2+10 = 12
seconds since the wait for the response was not accounted for. Substract
that wait from the 10 second wait time to start the retries more quickly
based on the 10 second timer described in the tech spec.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If unicast Authentication Request frame is used and the peer ACKs such a
frame, but does not reply within the two second limit, there is no need
to continue trying to retransmit the request frames since the peer was
found, but not responsive.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new conf={sta,ap}-{sae,psk-sae} parameter values can now be used to
specify that the legacy configuration object is for SAE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows DPP to be used for enrolling credentials for SAE networks in
addition to the legacy PSK (WPA-PSK) case. In addition, enable FT-PSK
and FT-SAE cases automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Retransmit the PKEX Exchange Request frame if no response from a peer is
received. This makes the exchange more robust since this frame is sent
to a broadcast address and has no link layer retries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to allow more invalid attribute values to be written
into Peer Discovery Request/Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to cover a case where Config Attrib Object value is
invalid in Configuration Request frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant DPP implementation to retransmit DPP
Authentication Response frame every 10 seconds up to 5 times if the peer
does not reply with DPP Authentication Confirm frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this command stopped listen operation immediately, but if
there was an ongoing authentication exchange, a new listen operation was
started. This is not really expected behavior, so stop the
authentication exchange first with this command to avoid restarting
listen operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new role=either parameter can now be used with DPP_AUTH_INIT to
indicate that the initiator can take either the Configurator or Enrollee
role.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant to iterate over all available channels from
the intersection of what the peer indicates and the local device
supports when initiating DPP Authentication. In addition, retry DPP
Authentication Request frame up to five times if no response is
received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Generate the PKEX bootstrapping information and release the PKEX session
in a helper function that both the initiator and responder can use
instead of maintaining this functionality separately in two places.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces the ACS functionality for the autonomous GO. The
optional parameter <freq> in p2p_group_add is enhanced to carry a value
"acs" with the intention to select the channels among any supported
band. freq = 2 / 5 carry the need to select the channels only in the
respective bands 2.4 / 5 GHz. This functionality is on top of the host
driver's capability to offload ACS, which is advertized through
WPA_DRIVER_FLAGS_ACS_OFFLOAD.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add limit on number of failed attempts that could have used PKEX code.
If the limit (5) is reached, drop the PKEX state (including the code)
and report this on the control interface to indicate that a new code
needs to be entered due to possible attack.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Clean up the pending PKEX exchange if Commit-Reveal Request processing
indicates a mismatch in the PKEX code. Previously, the this case was
silently ignored and the session was left in pending state that
prevented new PKEX exchanges from getting initated. Now, a new attempt
is allowed to be initiated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Report mismatching finite cyclic group with PKEX Exchange Response using
STATUS_BAD_GROUP and provide more detailed error report over the control
interface on the peer device when this happens.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Indicate to upper layers if PKEX Commit-Reveal Request frame AES-SIV
decryption fails. That is a likely sign of the PKEX code mismatch
between the devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
DPP AKM should really require PMF to be used, but since that is not yet
explicitly required in the specification, make PMF enabled for now. For
legacy PSK cases, configure PMF to be enabled as well to support both
APs in no-PMF, optional-PMF, and required-PMF configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow the Initiator to request a different channel to be used for DPP
Authentication and DPP Configuration exchanges. This commit adds support
for this in wpa_supplicant with the optional neg_freq=<freq in MHz>
parameter in DPP_AUTH_INIT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows wpa_supplicant dpp_config_obj_override,
dpp_discovery_override, and dpp_groups_override parameters to be cleared
by setting them to a zero-length value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Both the DPP-TX and DPP-TX-STATUS events are provided.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that dpp_check_attrs() takes care of verifying that no attributes
are after the Wrapped Data attribute, the duplicated checks in hostapd
and wpa_supplicant side of the implementation can be removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a generic mechanism for configuring the DPP implementation to behave
in particular different (mostly incorrect) ways for protocol testing
purposes. The new dpp_test parameter can be set to a non-zero integer to
indicate a specific behavior. This is only available in
CONFIG_TESTING_OPTIONS=y builds.
This commit include cases for an extra attribute being added after the
Wrapped Data attribute and Initiator/Responder capabilities having an
unexpected zero capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Seems like some test cases, e.g., ap_wpa2_psk_ext_retry_msg_3c, require
larger buffer than 256 bytes.
In other case I fail such test cases when run on real HW and using:
CONFIG_CTRL_IFACE=udp-remote
Increase the RX buffer from 256 to 4096 bytes to match the other control
interface cases.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
After an initial connection wpa_supplicant derives ERP information which
can be used in doing eventual authentications in the same realm. This
information can be used by drivers with offloaded FILS support to do
driver/firmware initiated roamings. Add support to send this updated
information to such drivers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to be able to use the same implementation for updating
the connection parameters in the driver during an association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update the replay counter after a roam for all cases. This restores the
design back to what it was before commit
01ef320f19 ('FILS: Update ERP next
sequence number with driver offload').
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant RESEND_ASSOC command can be used to request the
last (Re)Association Request frame to be sent to the AP to test FT
protocol behavior.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new wpa_supplicant "KEY_REQUEST <error=0/1> <pairwise=0/1>" command
can be used to request an EAPOL-Key Request frame to be sent to the AP.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.
This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.
Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 03ed0a5239 ('WNM: Ignore WNM-Sleep
Mode Response if WNM-Sleep Mode has not been used') started ignoring the
response when no WNM-Sleep Mode Request had been used during the
association. This can be made tighter by clearing the used flag when
successfully processing a response. This adds an additional layer of
protection against unexpected retransmissions of the response frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new sae_password network profile parameter can now be used to set
the SAE password instead of the previously used psk parameter. This
allows shorter than 8 characters and longer than 63 characters long
passwords to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While considering the movement of P2P GO from its current operating
channel, do not mark a DFS channel as invalid if DFS is offloaded
to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, wpas_p2p_select_go_freq_no_pref() ended up selecting a 2.4
GHz band channel first before even considering 5 or 60 GHz channels.
This was likely done more or less by accident rather than by design when
the 5 GHz and 60 GHz band extensions were added. It seems reasonable to
enhance this by reordering the code to start with 5 and 60 GHz operating
classes and move to 2.4 GHz band only if no channel was available in 5
or 60 GHz bands for P2P GO use.
This does have some potential interop issues with 2.4 GHz only peer
devices when starting up an autonomous GO (i.e., without there being
prior knowledge of channels that the peers support). Upper layers are
expected to enforce 2.4 GHz selection if that is needed for some use
cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows CONFIG_TESTING_OPTIONS=y builds of wpa_supplicant to
override the OWE DH Parameters element in (Re)Association Request frames
with arbitrary data specified with the "VENDOR_ELEM_ADD 13 <IE>"
command. This is only for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This additional field was added to DPP Public Action frames in DPP tech
spec v0.2.3 to support cryptographic agility in the future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only the SME-in-wpa_supplicant case was supported. This
extends that to cover the drivers that implement SME internally (e.g.,
through the cfg80211 Connect command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends OWE support in wpa_supplicant to allow DH groups 20 and 21
to be used in addition to the mandatory group 19 (NIST P-256). The group
is configured using the new network profile parameter owe_group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends OWE support in hostapd to allow DH groups 20 and 21 to be
used in addition to the mandatory group 19 (NIST P-256).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for using the OWE Transition Mode element to determine the
hidden SSID for an OWE BSS that is used in transition mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
sm->pmk_len was not set when deriving the PMK as part of OWE key
generation. This depending on wpa_sm_set_pmk_from_pmksa() call resetting
the value to the default. While this worked for many cases, this is not
correct and can have issues with network profile selection based on
association information. For example, the OWE transition mode cases
would hit an issue here.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new wpa_supplicant configuration parameters (go_interworking,
go_access_network_type, go_internet, go_venue_group, go_venue_type) to
add a possibility of configuring the P2P GO to advertise Interworking
element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update the default scan IEs when OCE is enabled/disabled to the
driver/firmware, so that the correct IEs will be sent out by the
driver/firmware in Probe Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds phase1 parameter tls_suiteb=1 into wpa_supplicant
configuration to allow TLS library (only OpenSSL supported for now) to
use Suite B 192-bit level rules with RSA when using >= 3k (3072) keys.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new psk=<hexdump> can be used as an alternative to pass=<passphrase>
when configuring the DPP Configurator with a legacy network parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, wowlan_triggers were updated in kernel only during startup.
Also update it whenever it is set from the control interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the code that writes mesh_rssi_threshold to a network block
always executes, but the code that reads it from network block and the
code that initializes it to a default value in a new network block are
inside #ifdef CONFIG_MESH. As a result when writing a config file it
will write mesh_rssi_threshold (since it has a non-default value) and
later fail to read the network block.
Fix this by moving the write code under #ifdef CONFIG_MESH as well.
Note, network blocks which already have mesh_rssi_threshold because of
the bug will still fail to read after the fix.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
The introduction of radio works and a delayed callback to complete
association/connection requests ended up breaking RSN pre-authentication
candidate list generation for the case of pre-connection scan results.
Previously, wpa_supplicant_associate() set the RSN state machine
configuration before returning and the calls to
wpa_supplicant_rsn_preauth_scan_results() immediately after this
function call were working fine. However, with the radio work callback,
the RSN state machine configuration started to happen only in that
callback which would be called soon after this code path has completed.
This resulted in the RSN state machine not knowing the selected SSID and
as such, rejecting all pre-authentication candidates.
Fix this by setting the RSN state machine configuration from
wpa_supplicant_associate() so that the existing callers of
wpa_supplicant_rsn_preauth_scan_results() can be used as-is to add
candidates for pre-authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
secy_init_macsec() can fail (if ->macsec_init fails), and
ieee802_1x_kay_init() should handle this and not let MKA run any
further, because nothing is going to work anyway.
On failure, ieee802_1x_kay_init() must deinit its kay, which will free
kay->ctx, so ieee802_1x_kay_init callers (only ieee802_1x_alloc_kay_sm)
must not do it. Before this patch there is a double-free of the ctx
argument when ieee802_1x_kay_deinit() was called.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
When building wpa_ie in wpas_start_assoc_cb() with ext_capab,
make sure that assignment does not exceed max_wpa_ie_len.
Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
This introduces a new interface for mesh and adds a signal that
is similar to the control interface event MESH-GROUP-STARTED.
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
The new "SET sae_commit_override <hexdump>" control interface command
can be used to force wpa_supplicant to override SAE commit message
fields for testing purposes. This is included only in
CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
DPP tech spec changed the contents of these frames by replacing the
public key hash attributes with a Transaction ID attribute that gets
copied from the request to the response to identify the transaction in a
simpler manner.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, CONFIG_WNM enabled build that supports WNM for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode WNM is required and there is no need for AP mode WNM.
Add support to differentiate between station mode WNM and AP mode
WNM in wpa_supplicant builds by adding CONFIG_WNM_AP that should be
used when AP mode WNM support is required in addition to station mode
WNM. This allows binary size to be reduced for builds that require
only the station side WNM functionality.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When setting the frequencies for beacon report request scan, it is
possible that a frequency is added twice (e.g., when the same channel
appears both in the channel field and in the AP channel report
subelement). This may cause the scan request to fail.
Make sure the frequencies array contains no duplications before
requesting the scan.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Send Radio Measurement response with measurement mode set to reject
in the following cases:
1. Reporting conditions is not supported.
2. No valid channels found for the measurement
Sending a response with an incapable indication will stop the AP from
sending other measurement requests of the same type as specified
in IEEE Std 802.11-2016, 11.11.6.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When failing to trigger scan for beacon report (e.g., when the
requested duration is not supported by the driver), send a
Radio Measurement response with the mode set to refused and don't
retry the scan.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
IEEE Std 802.11-2016, 11.11.6 specifies that a station that is unable to
make a requested measurement or refuses to make a measurement shall
respond only if the measurement request was received within an
individually addressed radio measurement request frame, but shall not
respond if such a request was received in a group addressed frame.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a build option to select different default ciphers for OpenSSL
instead of the hardcoded default "DEFAULT:!EXP:!LOW".
This new option is useful on distributions where the security level
should be consistent for all applications, as in Fedora [1]. In such
cases the new configuration option would be set to "" or
"PROFILE=SYSTEM" to select the global crypto policy by default.
[1] https://fedoraproject.org/wiki/Changes/CryptoPolicy
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
If an AP is not FILS capable and wpa_supplicant has a saved network
block for the network with FILS key management and a saved erp info,
wpa_supplicant might end up issuing a FILS connection to a non-FILS AP.
Fix this by looking for the presence of FILS AKMs in wpa_s->key_mgmt,
i.e., after deciding on the AKM suites to use for the current
connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In case that an mbo object is allocated, but there is a failure
to resize the wpabuf, need to free the mbo object.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Scan results with parent TSF older than the scan start TSF are not added
to the beacon report since they are considered as scan results from
previous scans. However, for drivers that report the scan start TSF but
not the parent TSF of each scan result, the parent TSF will be zero so
valid scan results will be dropped.
Fix this by filtering scan results by the parent TSF only if the
driver supports reporting the parent TSF for each scan result.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Clear the get_pref_freq_list_override in p2p_ctrl_flush(). This fixes
the case when a dedicated P2P device interface is used.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
dpp.h file requires openssl in order to compile, which breaks
compilation on systems without it.
Move DPP_OUI_TYPE to ieee802_11_defs.h and don't include dpp.h when
not really needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
If a DFS forced frequency is provided in 'p2p_group_add' and the driver
supports DFS offload, the frequency was rejected in
wpas_p2p_init_go_params(). However, it was accepted in
wpas_p2p_select_go_freq() and wpas_p2p_group_add(). To make the behavior
consistent, the DFS frequency is now accepted in
wpas_p2p_init_go_params() similar to the way done in
wpas_p2p_select_go_freq().
Redundant check in wpas_p2p_group_add() for DFS forced frequency is
removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add changes to control interface command get_capability to advertize
FILS capability, FILS AKMs suites, and FILS Authentication algorithms
based on the driver capabilities.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support to scan for a specific BSSID through the wpa_supplicant
control interface.
Usage: wpa_cli scan bssid=ab:bc:cd🇩🇪ef:12
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The DPP Configurator can use this new command to generate its own signed
connector for the network that it manages.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
All the arguments to this command are optional, so do not mandate at
least one to be included in wpa_cli.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows wpa_supplicant to be configured to act as the configurator
in the case where a peer device initiates DPP Authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements genric PKEX functionality in src/common/dpp.c and glue
code to use this in wpa_supplicant (i.e, hostapd DPP implementation does
not yet support PKEX).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Set temporary disallowed BSSID list to the driver so that the driver
doesn't try to connect to any of the blacklisted BSSIDs during
driver-based roaming operation. This commit includes support only for
the nl80211 driver interface using a QCA vendor command for this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new pass=<hexdump> parameter to DPP_AUTH_INIT can now be used to
specify the passphrase to use in config object.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new ssid=<hexdump> parameter to DPP_AUTH_INIT can now be used to
specify the SSID to use in config object.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This script can be used to process Android logcat information for
scanned QR Codes (e.g., from Barcode Scanner app) and also to display QR
Codes for locally generated bootstrap keys.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can now be configured to generate a network profile
automatically based on DPP configuration. The following
dpp_config_processing values can be used to specify the behavior:
0 = report received configuration to an external program for
processing; do not generate any network profile internally (default)
1 = report received configuration to an external program and generate
a network profile internally, but do not automatically connect
to the created (disabled) profile; the network profile id is
reported to external programs
2 = report received configuration to an external program, generate
a network profile internally, try to connect to the created
profile automatically
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 5538fc9309 ('FILS: Track completion
with FILS shared key authentication offload') added an additional case
for calling wpa_supplicant_event_assoc_auth() from EVENT_ASSOC handling
in case of FILS-completion with driver-based-SME. However, that checked
what placed outside the data != NULL case while data != NULL needs to
apply for this case as well due to wpa_supplicant_event_assoc_auth()
behavior. Move the data != NULL check to apply to both cases to avoid
potentially issues if a driver interface were to return EVENT_ASSOC
without the associate data. (CID 164708)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While encoded == NULL could happen in the case of an empty blob, that
will result in encoded_len == 0 and base64_decode() not derefencing the
src argument. That seems to be too difficult for some static analyzers,
so to avoid false warnings, explicitly reject the encoded == NULL case
without even trying to base64 decode it. (CID 164709)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds DPP bootstrapping, authentication, and configuration into
hostapd similarly to how the design was integrated in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for DPP Configuration Protocol using GAS. Full
generation and processing of the configuration object is not included in
this commit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add wpa_supplicant control interface commands for parsing the bootstrap
info URI from a QR Code (get peer public key) and to generate a new
bootstrap info with private key for local use. The optional
key=<hexdump> argument to the DPP_BOOTSTRAP_GEN command can be used to
specify the bootstrapping private key in OpenSSL ECPrivateKey DER
encoding format. This results in the local bootstrapping information
entry being created with the specified key instead of generating a new
random one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There could be multiple pending TX operations and if the earlier ones
have used wait_time, but the last one did not, the driver call for
canceling pending wait was not done. This could result in the driver
getting stuck waiting for the previously scheduled wait time and not
being able to do new operations until that. Fix this by canceling the
wait if any of the past offchannel_send_action() calls since the last
offchannel_send_action_done() used non-zero wait_time.
This was showing up as issues in certain DPP Public Action frame
sequences when the same offchannel operation is used with multiple
frames and the last frame in the sequence does not need wait_time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The additional SHA-384 and SHA-512 functionality is needed to support
DPP with various ECC curves.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This can be helpful in figuring out what happened if P2P_FIND operation
is unexpectedly rejected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_s->p2p_in_provisioning needs to be cleared when group formation
fully completes. The change to postpone GO side handling to the first
data connection in commit 41f853235f
('P2P: Extend group formation timeout on GO to first data connection')
resulted in making this not happen in one P2P Client side case: EAP-WSC
timeout in PBC case. While that is quite special case since it requires
30 second timeout without receiving new EAPOL frames and not getting
disassociation, it can apparently happen in some cases in practice. This
would result in new P2P operations (e.g., P2P_FIND) getting rejected
until wpa_supplicant is restarted.
Fix this by clearing wpa_s->p2p_in_provisioning whenever processing a
group formation failure case. For group formation success,
wpa_s->p2p_in_provisioning is left set to non-zero value to avoid
breaking the earlier limits on the GO side.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the eap_proxy mechanism to be used with multiple SIMs by
following the configured sim_num to index which SIM to use for when
fetching the IMSI through eap_proxy.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit is similar to the commit
783c2920cc ('P2P: Check if the pref_freq
reported by the driver supports P2P') but extends the check for
supported pref_freq to wpas_p2p_select_go_freq().
This avoids issues with P2P_GROUP_ADD ending up selecting an unexpected
channel when get_pref_freq_list() (i.e.,
QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST) is used. Filter the
list by removing channels that do not allow P2P operation at all.
Previously, only the explicitly disallowed channels were removed and
that could have resulted in selecting an operating channel that is not
allowed for P2P and failing to complete the operation to start the
group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add NULL checking for EAP name. If it is NULL, do not add the phase2
parameter autheap. This should not happen in practice due to earlier
checks for credential matching, but if there is a code path that would
allow this to be set, it is better to skip setting of the invalid value
and allow automatic selection of the Phase 2 parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Change in any network configuration at runtime will cause flush to
PMKSA cache. For most of the network parameters if there is no change
in value, PMKSA flush is not performed except 'bssid' and 'priority'.
Add 'bssid_hint' to exemption list of avoiding PMKSA flush on change.
This is needed to complete change in commit
43a356b268 ('Provide option to configure
BSSID hint for a network').
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Current DFS domain information of the driver can be used in ap/dfs
to comply with DFS domain specific requirements like uniform spreading
for ETSI domain.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
This exposes user configurable option to set bssid_hint for a network.
bssid_hint indicates which BSS has been found a suitable candidate for
initial association for drivers that use driver/firmware-based BSS
selection. Unlike the bssid parameter, bssid_hint does not limit the
driver from selecting other BSSs in the ESS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Addition of remove_ies() handled the CONFIG_IEEE80211R dependency, but
missed the caller being within CONFIG_FILS as well.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When reducing the configuration for MACsec/MKA to the bare minimum, so
no EAP authentication, just MACsec/MKA SA use with preshared key/name,
the EAPOL engine is still needed to run the protocol for MKA. Without
any EAP authentication options the IEEE8021X_EAPOL option is not set,
resulting in a non-working Key Agreement Entity.
Therefore the CONFIG_MACSEC block needs to move up and set the
IEEE8021X_EAPOL option.
Signed-off-by: Jaap Keuter <jaap.keuter@xs4all.nl>
In some practical cases, it is useful to suppress joining to node in the
distance. The new field mesh_rssi_threshold could be used as RSSI
threshold for joining.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This patch adds "TDLSCancelChannelSwitch" dbus method on
"fi.w1.wpa_supplicant1.Interface" interface to disable channel switching
with a TDLS peer.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
This patch adds "TDLSChannelSwitch" dbus method on
"fi.w1.wpa_supplicant1.Interface" interface to enable channel switching
with a TDLS peer.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
Derive PMK-R0 and the relevant key names when using FILS authentication
for initial FT mobility domain association. Fill in the FT IEs in
(Re)Association Request frame for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add support to set ignore assoc disallow to the driver so that the
driver ignores assoc disallowed bit set by APs while connecting. This is
used by drivers that handle BSS selection and roaming internally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver provides input on MBO transition candidate handling, the
target value in get_mbo_transition_candidate() can be NULL if the driver
provided BSSID is not found in the wpa_supplicant BSS table. And later
it would be dereferenced. Fix this by adding an explicit check before
dereferencing the pointer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant build with MBO enabled failed in CONFIG_WNM=y was not
specified explicitly. Add the WNM dependency automatically to avoid
needing explicit addition in build configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 34f2851902 ('MBO: Parse MBO
ANQP-element on STA') started using the type variable outside
CONFIG_HS20 block, but forgot to remove the ifdef from the variable
declaration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Disconnection due to DISABLE_NETWORK while being connected was resulting
in the AP getting blacklisted. Avoid this by setting own_disconnect_req
on a disconnect request due to DISABLE_NETWORK similarly to the
SELECT_NETWORK disconnection case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a string "FILS_HLP_SENT" to connect event when HLP is sent
as part of ASSOC/CONNECT request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the uuid configuration parameter is not set, wpa_supplicant generates
an UUID automatically to allow WPS operations to proceed. This was
previously always using an UUID generated from the MAC address. This
commit adds an option to use a random UUID instead. The type of the
automatically generated UUID is set with the auto_uuid parameter: 0 =
based on MAC address (default; old behavior), 1 = random UUID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new PMKSA cache entry within wpa_supplicant if a driver event from
offloaded FILS shared key authentication indicates a new PMKSA entry was
created.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This keeps the internal ERP information within wpa_supplicant in sync
with the driver when offloading FILS shared key authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update the internal fils_completed state when offloading FILS shared key
authentication to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add FILS/ERP parameters into the driver connect command to support FILS
shared key authentication offload.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was already done in sme_send_authentication() for the case where
wpa_supplicant SME is used. Similar change is needed for driver-SME to
allow FILS authentication to be offloaded to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for setting and deleting PMKSA cache entries based on FILS Cache
Identifer. Also additionally add support for sending PMK as part of
SET_PMKSA to enable driver to derive keys in case of FILS shared key
offload using PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When using FILS for FT initial mobility domain association, add MDE to
the Authentication frame from the STA to indicate this special case for
FILS authentication.
Signed-off-by: Jouni Malinen <j@w1.fi>
PMKSA_ADD and MESH_PMKSA_ADD command arguments include keying material,
so show it in debug log only if requested to do with the command line -K
argument.
Signed-off-by: Jouni Malinen <j@w1.fi>
In ap_scan=2 mode, wpa_supplicant_assoc_try() did not check whether the
SSID is temporarily disabled before trying to associate and this may
result in an infinite connect/disconnect loop. If the association
succeeds while the SSID is temporarily disabled, wpa_supplicant will
request to deauthenticate and that in turn will cause the SSID to be
temporarily disabled again. Fix that by postponing the association until
the SSID is no longer temporarily disabled.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Without CONFIG_P2P config, the following warning occurs if CONFIG_AP is
enabled for the build:
ap.c: In function ‘wpas_conf_ap_vht’:
ap.c:54:5: warning: unused variable ‘channel’ [-Wunused-variable]
u8 channel = conf->channel;
^
ap.c:53:5: warning: unused variable ‘center_chan’ [-Wunused-variable]
u8 center_chan = 0;
^
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This change fixes the following compilation warnings:
wnm_sta.c:1007:4: warning: implicit conversion from enumeration type
'enum mbo_transition_reason' to different enumeration type
'enum mbo_transition_reject_reason' [-Wenum-conversion]
The actual value of both MBO_TRANSITION_REASON_UNSPECIFIED and
MBO_TRANSITION_REJECT_REASON_UNSPECIFIED is 0, so this does not result
in any change in the contents of the frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only the success and failure (to TX) cases were handled. It
is also possible for the driver to transmit the frame, but not receive
an ACK from the recipient. Address that by waiting for a short period of
time for a response. This fixes cases where OSU provider icon fetching
could get stuck if no ACK frame is received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not try to use FILS authentication unless the AP indicates support
for the type the local network profile enforces.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds an option to configure wpa_supplicant to use the perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime network profile parameter fils_dh_group is used to enable
this by specifying which DH group to use. For example, fils_dh_group=19
would use FILS SK PFS with a 256-bit random ECP group.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds STA side addition of OWE Diffie-Hellman Parameter element into
(Re)Association Request frame and processing it in (Re)Association
Response frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds AP side processing for OWE Diffie-Hellman Parameter element in
(Re)Association Request frame and adding it in (Re)Association Response
frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since VHT can be toggled explicitly, also expose being able to disable
HT explicitly, without requiring HT overrides. Continue making it
default to enabled though.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of deducing the wide (HT, VHT) channel configuration only
automatically in P2P mode, allow it to be configured in the network
in non-P2P mode.
Also allow all of these parameters to be configured through the control
interface or the configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the event "WPS-PBC-ACTIVE" was only generated when
wpa_supplicant is operating as WPS Registrar whereas "WPS-SUCCESS" or
"WPS-TIMEOUT" are generated for both, the Registrar and the Enrollee
roles.
Also generate the event when wpa_supplicant is operating as WPS Enrollee
to allow monitoring the begin and the end of a WPS PBC process.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
There's no point in making the code use a stack buffer and first copying
the string there, only to copy it again to the output. Make the output
directly use the reason string.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is now possible to add neighbor configuration to wnm_bss_query.
Update the auto complete message to reflect that.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a mechanism to configure the candidates for BTM query candidate list
manually. This can be used to verify AP behavior for various candidates
preferences.
usage:
wnm_bss_query <reason> [neighbor=<BSSID>,<BSSID information>,
<operating class>,<channel number>,
<PHY type>[,<hexdump of optional subelements>]]
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
BSS transition management query and response use a large static buffer
for the frame because the candidate list may require a lot of space.
However, in most cases the actually used space will be much less than
the buffer (since the candidate list is short or completely missing).
Use a dynamically allocated buffer instead and allocate it according
to the actual space needed.
While at it, remove unneeded filling of the MAC header in the Action
frames, since this gets ignored and wpa_drv_send_action() adds the MAC
header anyway.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This extends the GAS/ANQP parser in wpa_supplicant to process MBO
ANQP-elements and indicate received Cellular Data Connection Preference
values over the control interface.
When a valid MBO ANQP-element is received, the following control
interface message is sent:
RX-MBO-ANQP <BSSID> cell_conn_pref=<value>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, ANQP_GET required at least one IEEE 802.11 ANQP-element to
be requested. This is not really necessary, so allow a case where
num_ids == 0 as long as the request includes at least one Hotspot 2.0 or
MBO ANQP-element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
MBO techspec v0.0_r27 changed the MBO ANQP-element format. The MBO
element in ANQP query should now include an MBO Query List element that
contains a list of MBO elements to query.
Add API to add the MBO Query List to an ANQP query.
Format:
ANQP_GET <addr> <info_id>[,<info_id>]...[,mbo:<subtype>...]
Example for querying neighbor report with MBO cellular data
connection preference:
ANQP_GET <bssid> 272,mbo:2
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The userspace may want to delay the the first scheduled scan.
This enhances sched_scan to add initial delay (in seconds) before
starting first scan cycle. The driver may optionally choose to
ignore this parameter and start immediately (or at any other time).
This uses NL80211_ATTR_SCHED_SCAN_DELAY to add this via user
global configurable option: sched_scan_start_delay.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The while (len) loop was updating the next pointer at the end even when
len == 0, i.e., when the new next value won't be used. This could result
in reading one octet beyond the end of the allocated response wpabuf.
While the read value is not really used in practice, this is not correct
behavior, so fix this by skipping the unnecessary next pointer update in
len == 0 case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The maximum required size for each Beacon Report element is known in
advance: it is the size of the Beacon Report element fixed fields + the
size of the Reported Frame Body subelement.
Allocate the buffer used for constructing the Beacon Report element
dynamically with the maximum needed size, instead of using a very
large static buffer.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This leads to cleaner code overall, and also reduces the size
of the hostapd and wpa_supplicant binaries (in hwsim test build
on x86_64) by about 2.5 and 3.5KiB respectively.
The mechanical conversions all over the code were done with
the following spatch:
@@
expression SIZE, SRC;
expression a;
@@
-a = os_malloc(SIZE);
+a = os_memdup(SRC, SIZE);
<...
if (!a) {...}
...>
-os_memcpy(a, SRC, SIZE);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for rejecting a BSS transition request using MBO reject
reason codes. A candidate is selected or rejected based on whether it is
found acceptable by both wpa_supplicant and the driver. Also accept any
candidate meeting a certain threshold if disassoc imminent is set in BTM
Request frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add driver interface command using the QCA vendor extensions to check
the driverr whether to accept or reject a BSS transition candidate. For
the reject case, report an MBO reject reason code.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The parsing code expects non_pref_chan to be non-quoted.
Fix the example in wpa_supplicant.conf not to include
quotes.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Previously it was possible for wpa_s->scan_res_handler to remain set to
its old value in case wpa_drv_scan() failed and no retry for the scan
trigger was scheduled (i.e., when last_scan_req == MANUAL_SCAN_REQ).
This could result in getting stuck with the next connection attempt
after a failed "SCAN TYPE=ONLY" operation when wpa_s->scan_res_handler
was set to scan_only_handler().
Fix this by clearing wpa_s->scan_res_handler if wpa_drv_scan() fails and
no retry is scheduled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
CONFIG_TLS=linux can now be used to select the crypto implementation
that uses the user space socket interface (AF_ALG) for the Linux kernel
crypto implementation. This commit includes some of the cipher, hash,
and HMAC functions. The functions that are not available through AF_ALG
(e.g., the actual TLS implementation) use the internal implementation
(CONFIG_TLS=internal).
Signed-off-by: Jouni Malinen <j@w1.fi>
The reason detail field in non_pref_chan attribute was removed
from MBO draft v0.0_r25. Also oper_class can be 1 character for
few country codes (e.g., country code-UK, channel number-1). So the
shortest channel configuration is 7 characters.
This was missed in the earlier commit
4a83d4b686 ('MBO: Do not add reason_detail
in non_pref_chan attr (STA)') that took care of other changes related to
removal of the reason detail.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
aes-siv.c needs functions from aes-ctr.c and aes-omac1.c, so set
NEED_AES_CTR=y and NEED_AES_OMAC1=y if NEED_AES_SIV is defined. This
fixes some build configuration combinations where either of those
dependencies were not pulled in through other parameters. For example,
some CONFIG_FILS=y cases were impacted.
Signed-off-by: Jouni Malinen <j@w1.fi>
This functionality was originally added in commit
204c9ac4ee ('Extend select_network command
with freq= to reduce scan time') re-using wpa_s->manual_scan_freqs and
MANUAL_SCAN_REQ. That got broken when commit
35d403096e ('Set NORMAL_SCAN_REQ on
SELECT_NETWORK/ENABLE_NETWORK') started overriding wpa_s->scan_req for
SELECT_NETWORK.
Fix this by adding a new scan frequency list specifically for
SELECT_NETWORK so that this does not need to depend on any specific
wpa_s->scan_req value.
Signed-off-by: Jouni Malinen <j@w1.fi>
The PMKSA_GET and PMKSA_ADD commands can now use an optional extra
parameter to fetch and add PMKSA cache entries with the FILS Cache
Identifier.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows PMKSA cache entries for FILS-enabled BSSs to be shared
within an ESS when the BSSs advertise the same FILS Cache Identifier
value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The ft_completed for FILS authentication case in
wpa_supplicant_event_assoc() depends on something having cleared
portValid so that setting it TRUE ends up authorizing the port. This
clearing part did not happen when using FILS authentication during a
reassociation within an ESS. Fix this by clearing portValid in
sme_send_authentication() just before the keys are cleared (i.e., the
old connection would not be usable anyway).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The RSN supplicant implementation needs to be updated to use the new
BSSID whenever doing FILS authentication. Previously, this was only done
when notifying association and that was too late for the case of
reassociation. Fix this by providing the new BSSID when calling
fils_process_auth(). This makes PTK derivation use the correct BSSID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds reason for timeout in event CTRL-EVENT-ASSOC-REJECT whenever
connection failure happens because of timeout. This extends the
"timeout" parameter in the event to include the reason, if available:
timeout=scan, timeout=auth, timeout=assoc.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE 802.11ax HE changes to include HE IEs in Beacon and Probe Response
frames. These elements are using vendor specific forms for now since the
IEEE 802.11ax draft is not yet finalized and the element contents is
subject to change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add IEEE 802.11ax definitions for config, IEEE structures, and
constants. These are still subject to change in the IEEE process.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Let mesh STA A be a STA which has config disable_ht=1.
Let mesh STA B be a STA which has config disable_ht=0.
The mesh STA A and B was connected.
Previously, the mesh STA A sent frame with HT rate even though its HT
was disabled. This commit fixes the issue by checking the local BSS HT
configuration.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The new "SET ric_ies <hexdump>" control interface command can now be
used to request wpa_supplicant to add the specified RIC elements into
Reassociation Request frame when using FT protocol. This is mainly for
testing purposes.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a copy of the internal HMAC-SHA256 implementation with the hash
block size and output length updated to match SHA384 parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
This new P2P_SET parameter uses <op_class>:<channel> format and is used
mainly for testing purposes to allow overriding the value of the GO
Negotiation Response frame Operating Channel attribute.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This can be used to override driver get_pref_freq_list() operation for
more convenient testing of preferred frequency list functionality.
Override string format:
<if_type1>:<freq1>,<freq2>,... <if_type2>:...
if_type: 0=STATION, 2=AP, 3=P2P_GO, 4=P2P_CLIENT, 8=TDLS, 9=IBSS
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the est_throughput comparison was done only when SNR
difference was less than 5 dB. Since the throughput estimation take into
account SNR, this can be done in more cases. For now, add a conservative
2 dB more to the difference so that any SNR difference below 7 dB
results in BSS selection based on throughput estimates.
In addition, the throughput estimates require SNR values to be
available, so separate this from the 5 GHz preference that can be done
based on either SNR or qual values.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows throughput estimates and 5 GHz preference over 2.4 GHz band
to be used in more cases. The previously used value of 30 was
significantly more conservative than the SNR limits used for the highest
rate in scan_est_throughput() and this resulted in cases where 5 GHz AP
was ignored while SNR with it would have been close to reaching the
maximum TX rate.
Signed-off-by: Jouni Malinen <j@w1.fi>
The published P802.11ai version does not use CRC32 anymore, so remove
inclusion of crc32.o into wpa_supplicant and hostapd builds based on
CONFIG_FILS=y.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new edits from defconfig to android.config. No new build
options are enabled, i.e., this is only bringing in comment updates and
new parameters in commented out form.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add support to set sched scan relative RSSI parameters so that the
drivers can report BSSs after relative comparision with the current
connected BSS. This feature is applicable only when in connected mode.
The below commands can be used to configure relative RSSI parameters
SET relative_rssi <disable|rssi_value>
disable - to disable the feature
rssi_value - amount of relative RSSI in dB
SET relative_band_adjust <band:adjust_value>
band - "2G" or "5G" for 2.4 GHz or 5 GHz respectively
adjust_value - amount of RSSI to be adjusted in dB
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add an internal flag which indicates to tunneled EAP methods (FAST,
PEAP, TTLS) that they should cache decrypted EAP-SIM/AKA/AKA' requests.
This allows EAP-SIM/AKA/AKA' to be tunneled within these outer methods
while using an external SIM authenticator over the control interface.
Signed-off-by: Paul Stewart <pstew@google.com>
Clean up the event message by removing the ie=<value> parameter when the
IEs are not available instead of printing out "ie=(null)".
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Free the pending frequency list if a second beacon request is received
before the scan for the previous one has been completed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Sched scan is supported by the kernel also in the connected state, so
allow PNO scan to be issued in the connected state from wpa_supplicant
as well.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The current implementation of QCA vendor scan does not handle the
simultaneous scan/p2p-scan operations on the same interface due to
missing support for tracking multiple scan cookie values. Hence
serialize such operations on the same interface for now.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The only_new_results=1 scan parameter was previously set on other scan
cases, but not on the two P2P specific scan triggers. Set this also for
those P2P cases to get consistent behavior after BSS_FLUSH.
This was showing up with number of hwsim P2P test cases maintaining
unexpected scan results from previous test cases due to the flush
operation not really working correctly since the cfg80211 BSS table was
not explicitly cleared.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support to send GAS requests with a randomized transmitter address
if supported by the driver. The following control interface commands
(and matching configuration file parameters) can be used to configure
different types of randomization:
"SET gas_rand_mac_addr 0" to disable randomizing TX MAC address,
"SET gas_rand_mac_addr 1" to randomize the complete TX MAC address,
"SET gas_rand_mac_addr 2" to randomize the TX MAC address except for OUI.
A new random MAC address will be generated for every
gas_rand_addr_lifetime seconds and this can be configured with
"SET gas_rand_addr_lifetime <timeout>".
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, VHT capability was default value (=0x0000). This makes
VHT Capabilities Info in VHT Capabilities IE in mesh peering
open/confirm frame 0x0000. This patch fills it with hardware capability.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
wpa_group_update_count and wpa_pairwise_update_count can now be used to
set the GTK and PTK rekey retry limits (dot11RSNAConfigGroupUpdateCount
and dot11RSNAConfigPairwiseUpdateCount). Defaults set to current
hardcoded value (4).
Some stations may suffer from frequent deauthentications due to GTK
rekey failures: EAPOL 1/2 frame is not answered during the total timeout
period of currently ~3.5 seconds. For example, a Galaxy S6 with Android
6.0.1 appears to go into power save mode for up to 5 seconds. Increasing
wpa_group_update_count to 6 fixed this issue.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
Relying on the group_capab from the P2P peer information can result in
improper information on whether the peer is currently operating as a GO.
However, there is a known implementation in Android that does this.
To reduce issues from this misuse in upper layer to try to determine
whether a specific peer is operationg a group, override the group_capab
value in P2P_PEER output with 0 if there are no BSS entries with the
peer P2P Device as a GO. This is not a perfect information since there
may not have been a recent scan on all channels, but this results in
less issues than trying to decide between new group formation and
joining an existing group based on stale or incorrect information.
Since no upper layer application is really supposed to use the
group_capab field value in P2P_PEER command, this change should not
cause any impact for properly design components and the possibility of
regressions is limited to cases that are already known to work
incorrectly in number of identifiable cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 8d1e693186 ('Use estimated
throughput to avoid signal based roaming decision') added a check for
the current BSS estimated throughput being significantly higher than the
selected BSS estimated throughput. However, this case for skipping a
roam used "return 1" which actually allows the roam. Fix this by
returning 0 in this case.
Signed-off-by: Jouni Malinen <j@w1.fi>
To be more consistent with existing hwaddr_aton() and hexstr2bin()
callers, check the return values in this test command.
Signed-off-by: Jouni Malinen <j@w1.fi>
The local custom version of allocating and initializing struct
hostapd_data within wpa_supplicant_mesh_init() is problematic. This has
already missed couple of initialization steps that are required. Instead
of trying to remember to keep this up to date, use
hostapd_alloc_bss_data() so that there is only one place for this
initialization.
This is fixing a recent issue where FILS HLP started using
hapd->dhcp_server and expected that to be initialized to -1. For the
mesh case, that did not happen and when removing the interface, the FILS
HLP implementation ended up unregistering eloop socket for
hapd->dhcp_server (= 0). This could result in missing socket callbacks
for an arbitrary socket.
Signed-off-by: Jouni Malinen <j@w1.fi>
This wpa_drv_if_remove() call was previously modified to fix a different
issue, but that fix resulted in unconditional use of treed memory here
(wpa_supplicant_deinit_iface() frees wpa_s). Make a local copy of
wpa_s->parent to be able to use it after wpa_s is freed. The
mesh_if_created case has wpa_s->parent != wpa_s, so this should be
sufficient way of handling the wpa_drv_if_remove() call here.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new FILS-HLP-RX control interface event is now used to report
received FILS HLP responses from (Re)Association Response frame as a
response to the HLP requests configured with FILS_HLP_REQ_ADD.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is independent functionality from the core IEEE 802.11 management
handling and will increase significantly in size, so it is cleaner to
maintain this in a separate source code file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible to hit this WPA_ASSERT when FST-MANAGER SESSION_REMOVE
command is exececuted when in not-associated state. In
CONFIG_EAPOL_TEST=y builds, this would result in the wpa_supplicant
process being terminated. Convert this WPA_ASSERT to a check that does
not terminate the process, but only rejects the command if wpa_s->bssid
does not match the da argument.
Signed-off-by: Jouni Malinen <j@w1.fi>
Increase the EAPOL RX frame timeout from 100 to 200 ms. This fixes lack
of optimization (i.e., first EAPOL frame dropped) in occasional roaming
and authentication cases on EAP networks if the kernel events can be
reordered and delayed a bit longer.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sonymobile.com>
Instead of copying the struct wpa_auth_callbacks, just keep a pointer to
it, keep the context pointer separate, and let the user just provide a
static const structure. This reduces the attack surface of heap
overwrites, since the function pointers move elsewhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the VHT capability override vht_disabled=1 is used in the network
profile, skip VHT configuration of the local channel.
Signed-off-by: Jouni Malinen <j@w1.fi>
The remote mesh STA which had configuration disable_ht40=1 could have HT
Capabilities element which includes Supported Channel Width Set = 1
(both 20 MHz and 40 MHz operation is supported) even though it had HT
Operation element which includes STA Channel Width = 0 (20 MHz channel
width only). Previously, local peer recognized such a remote peer as 40
MHz band width enabled STA because local peer only checked HT
Capabilities element. This could cause disconnection between
disable_ht40=1 mesh STA and disable_ht40=0 mesh STA. They could
establish a mesh BSS but could not ping with ath9k_htc device. This
commit fixes the issue by refering HT Operation element.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This functionality can be used outside wpa_set_disable_ht40(), so move
the generic part to a helper function.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The new wpa_supplicant control interface commands FILS_HLP_REQ_FLUSH and
FILS_HLP_REQ_ADD can now be used to request FILS HLP requests to be
added to the (Re)Association Request frame whenever FILS authentication
is used.
FILS_HLP_REQ_ADD parameters use the following format:
<destination MAC address> <hexdump of payload starting from ethertype>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When AP responds with comeback delay for initial GAS query sent by STA,
gas_query_timeout should be cancelled to avoid GAS failures when
comeback delay is more than GAS_QUERY_TIMEOUT_PERIOD. The
gas_query_timeout is getting registered again when tx_status is received
for GAS comeback request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These commnds are mesh version of PMKSA_GET/ADD commands. So the usage
and security risk is similar to them. Refer to
commit 3459381dd2 ('External persistent
storage for PMKSA cache entries') also.
The MESH_PMKSA_GET command requires peer MAC address or "any" as an
argument and outputs appropriate stored PMKSA cache. And the
MESH_PMKSA_ADD command receives an output of MESH_PMKSA_GET and re-store
the PMKSA cache into wpa_supplicant. By using re-stored PMKSA cache,
wpa_supplicant can skip commit message creation which can use
significant CPU resources.
The output of the MESH_PMKSA_GET command uses the following format:
<BSSID> <PMKID> <PMK> <expiration in seconds>
The example of MESH_PMKSA_ADD command is this.
MESH_PMKSA_ADD 02:00:00:00:03:00 231dc1c9fa2eed0354ea49e8ff2cc2dc cb0f6c9cab358a8146488566ca155421ab4f3ea4a6de2120050c149b797018fe 42930
MESH_PMKSA_ADD 02:00:00:00:04:00 d7e595916611640d3e4e8eac02909c3c eb414a33c74831275f25c2357b3c12e3d8bd2f2aab6cf781d6ade706be71321a 43180
This functionality is disabled by default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This can be used to determine whether the driver supports PMF and if so,
with which group management cipher suites. In addition, add the missing
pairwise and group cipher suite values to the documentation while adding
this new entry there as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
When wpa_supplicant was processing a received Authentication frame (seq
1) from a peer STA for which there was already a TK configured to the
driver, debug log claimed that the PTK gets cleared, but the actual
call to clear the key was actually dropped due to AUTH vs. SUPP set_key
selection. Fix this by explicitly clearing the TK in case it was set
and an Authentication frame (seq 1) is received.
This fixes some cases where EAPOL-Key frames were sent encrypted using
the old key when a peer STA restarted itself and lost the key and had to
re-join the IBSS. Previously, that state required timing out the 4-way
handshake and Deauthentication frame exchange to recover.
Signed-off-by: Jouni Malinen <j@w1.fi>
country[2] needs to be set to ' ' instead of left to '\0' for the case
where wpa_supplicant sets up AP mode operations and includes the Country
element. Currently, this would be only for DFS channels. Without this,
the Beacon frames would go out with incorrect third octet in the country
code.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This control interface command can be used to inject scan results from
test scripts to make it easier to test various scan result processing
operations.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previous version could have used uninitialized char* when a DMG with
invalid capabilities were added to BSS table from scan results.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a call to the notify_beacon_loss() callback functions when
beacon loss is detected. In addition, a new CTRL-EVENT-BEACON-LOSS event
is made available through the wpa_supplicant control interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
These parameters are global configuration parameters for wpa_supplicant
and the special control interface SET command handlers for them were
preventing the configuration update. Make this more consistent by
updating the configuration parameter as well since that is what all the
other SET <global config param> commands do.
Signed-off-by: Jouni Malinen <j@w1.fi>
non_pref_chan is a global configuration parameter for wpa_supplicant and
the special control interface SET command handler for it was preventing
the configuration update. Make this more consistent by updating the
configuration parameter as well since that is what all the other SET
<global config param> commands do.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 483dd6a5e0 ('Include peer
certificate always in EAP events') added this wpa_supplicant global
configuration parameter, but forgot to add the actual parsing of it, so
there was no way of setting the value.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a comment to note which fields are expected to be updated by the
driver. In addition, reorder subfield writing to match the order in
which the fields are in the frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
ieee80211_chan_to_freq() is not really meant for conversion of 20 MHz
primary channel numbers for wider VHT channels, so handle those as
special cases here for now.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpabuf_resize() can handle the initial allocation of a wpabuf and all
the other callers of wpas_rrm_report_elem() were already using a pointer
to a pointer and a wpabuf_resize() call. Simplify this by resizing the
wpabuf (if needed) within wpas_rrm_report_elem() instead of having to
calculate the needed size in all the callers. Thsi is also fixing one of
the allocation sizes to use the correct size instead of a size of a
struct that has nothing to do with the allocation (but is larger than
the needed five octets, so does not break anything).
Signed-off-by: Jouni Malinen <j@w1.fi>
There is only a single caller for wpas_rrm_send_neighbor_rep_request()
and it unconditionally uses a callback function, so cb cannot be NULL
here and there is no need for additional complexity and extra code size
to check for it explicitly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the check was done after we reached the maximum and another
scan was already triggered.
While at it, remove an irrelevant comment that the previous change in
the logic here missed.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Previously, SIM state change with SIM_STATE_ERROR cleared all PMKSA
entries (including non-SIM networks). Limit this to networks which use
SIM-based authentication methods to avoid unnecessarily removal of PMKSA
entries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The pending neighbor report state needs to be cleared on error path here
to avoid getting stuck with being unable to perform any additional
neighbor reports during the association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow shorter request since the subelements are optional to include.
Also print the hexdump of the subelements into debug log.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The requested behavior can be approximated for most use cases even if
the driver does not support reporting exact TSF values for frames.
Enable this capability for all drivers to make beacon report processing
more useful for a common use case.
Signed-off-by: Jouni Malinen <j@w1.fi>
The special parameters for beacon report scan are not needed for the
beacon report when using the beacon table measurement mode. Advertise
support for this case regardless of whether the driver supports the scan
parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
Beacon Report Radio Measurement is defined in IEEE Std 802.11-2016,
11.11.9.1. Beacon Report is implemented by triggering a scan on the
requested channels with the requested parameters.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This conversion will be done several times in the code, so add a helper
function that does this conversion.
Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
Extend verify_channel() to return whether IR is allowed on the channel
or not, and make it a global function so it can be used in other files,
too. This makes this function useful for checking not only if a channel
is supported but also if it is allowed for active and passive scan.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add the following parameters to scan request:
1. Dwell time on each channel.
2. Whether the specified dwell time is mandatory.
In addition, add to scan results info the time that the scan actually
started, and to each scan result the time the beacon/probe was received,
both in terms of TSF of the BSS that the interface that requested the
scan is connected to (if available).
Add flags to indicate whether the driver supports dwell time
configuration and scan information reporting.
This scan configuration and information is required to support beacon
report radio measurement.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
1. Change the return type to reflect whether building the report
succeeded or failed.
2. Change argument type to rrm_measurement_request_element instead
of raw packet data to ease processing the request.
3. Use already existing function to create the measurement report
and add it to the report buffer.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Send measurement report with the mode field set to incapable in response
to measurement requests with unsupported measurement types.
In addition, measurements requests that request parallel measurements
are rejected since these features are not supported.
Measurement request frames with the enable bit set are ignored since
these are not really requesting measurements and are not supported for
now.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The length of a Measurement Report frame should be limited by the
maximum allowed MMPDU size (IEEE Std 802.11-2016, 9.6.2.3). Enforce this
size limit, and in case the report elements are longer than the allowed
size, split them between several MPDUs.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Extract the code dealing with processing the measurement request
elements to a separate function. This will be needed for beacon report
requests processing.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
RRM request frame should contain only information elements of type Radio
Measurement Request. Go through all the frame and validate that only
elements of this type are included.
In addition, if a truncated element is encountered, or the element
length field indicates that the element length is more than the
entire frame, abort the request.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
As support for new RRM measurements will be added, the RRM
implementation will become quite large, so move it to a dedicated file.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Commit 4a742011ab ('wpa_supplicant: Handle
LCI request') introduced LCI request parsing in a manner that
incremented the request pointer by four within
wpas_rrm_build_lci_report() without decrementing len correspondingly.
This could potentially result in get_ie() reading four octets beyond the
buffer if a corrupted request is received. This would be applicable only
if the LCI reporting was enabled explicitly ("SET LCI ..." control
interface command).
Fix this by updating the len variable to match the request pointer
changes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a new wpa_supplicant network profile parameter
mka_priority=0..255 to set the priority of the MKA Actor.
Signed-off-by: Badrish Adiga H R <badrish.adigahr@gmail.com>
This was previously done for SCAN_RESULTS, but the BSS control interface
command did not show a similar flag. In addition, change "WPA2" to "RSN"
for mesh BSS to be consistent with the SCAN_RESULTS output.
Commit 638d945679 ('mesh: Show [MESH] flag
in scan results') did similar changes for SCAN_RESULTS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit extends the BSS commands to include "BSS CURRENT" as a way
to get the current BSS without having to walk the BSS list matching
against BSSID+SSID returned from the STATUS command.
This returns the BSS stored in wpa_s->current_bss.
Signed-off-by: Joel Cunningham <joel.cunningham@me.com>
This registers a new callback to indicate change in SIM state. This
helps to do some clean up (more specifically pmksa_flush) based on the
state change of the SIM. Without this, the reconnection using the cached
PMKSA could happen though the SIM is changed.
Currently eap_proxy_sim_state corresponds to only SIM_STATE_ERROR. This
can be further extended.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows user to start P2P Find/Scan on a particular frequency and
then move to scanning social channels. This support is already present
on control socket.
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>
Add p2p_add_cli_chan=1 option to p2p_supplicant.conf to allow Wi-Fi P2P
operating as P2P client on passive scan channels.
In addition, add p2p_add_cli_chan=1 option to wpa_supplicant.conf to
have consistency in P2P channel list. There is a case where P2P channel
list is updated with different channels from p2p0 and wlan0.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sonymobile.com>
Commit c579312736 ('Add
PMKSA-CACHE-ADDED/REMOVED events to wpa_supplicant') added new arguments
to these callback functions, but forgot to update the implementations in
preauth_test.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes both the Probe Response and Beacon frame IEs available to
upper layers if scan results include both IE sets. When the BSS command
mask includes WPA_BSS_MASK_BEACON_IE, a new beacon_ie=<hexdump> entry
will be included in output if the BSS entry has two separate sets of IEs
(ie=<hexdump> showing the Probe Response frame contents and
beacon_ie=<hexdump> the Beacon rame contents).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If 20/40 MHz co-ex scan resulted in switching primary and secondary
channels, mesh setup failed to update the frequency parameters for
hostapd side configuration and that could result in invalid secondary
channel configuration preventing creating of the mesh network. This
could happen, e.g., when trying to set up mesh on 5 GHz channel 36 and
co-ex scan finding a BSS on channel 40. Switching the pri/sec channels
resulted in hostapd code trying to check whether channel 32 is
available. Fix this by swapping the channels for hostapd configuration
when needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new wpa_supplicant control interface commands PMKSA_GET and
PMKSA_ADD that can be used to store PMKSA cache entries in an external
persistent storage when terminating a wpa_supplicant process and then
restore those entries when starting a new process. The previously added
PMKSA-CACHE-ADDED/REMOVED events can be used to help in synchronizing
the external storage with the memory-only volatile storage within
wpa_supplicant.
"PMKSA_GET <network_id>" fetches all stored PMKSA cache entries bound to
a specific network profile. The network_id of the current profile is
available with the STATUS command (id=<network_id). In addition, the
network_id is included in the PMKSA-CACHE-ADDED/REMOVED events. The
output of the PMKSA_GET command uses the following format:
<BSSID> <PMKID> <PMK> <reauth_time in seconds> <expiration in seconds>
<akmp> <opportunistic>
For example:
02:00:00:00:03:00 113b8b5dc8eda16594e8274df4caa3d4 355e98681d09e0b69d3a342f96998aa765d10c4459ac592459b5efc6b563eff6 30240 43200 1 0
02:00:00:00:04:00 bbdac8607aaaac28e16aacc9152ffe23 e3dd6adc390e685985e5f40e6fe72df846a0acadc59ba15c208d9cb41732a663 30240 43200 1 0
The PMKSA_GET command uses the following format:
<network_id> <BSSID> <PMKID> <PMK> <reauth_time in seconds> <expiration
in seconds> <akmp> <opportunistic>
(i.e., "PMKSA_ADD <network_id> " prefix followed by a line of PMKSA_GET
output data; however, the reauth_time and expiration values need to be
updated by decrementing them by number of seconds between the PMKSA_GET
and PMKSA_ADD commands)
For example:
PMKSA_ADD 0 02:00:00:00:03:00 113b8b5dc8eda16594e8274df4caa3d4 355e98681d09e0b69d3a342f96998aa765d10c4459ac592459b5efc6b563eff6 30140 43100 1 0
PMKSA_ADD 0 02:00:00:00:04:00 bbdac8607aaaac28e16aacc9152ffe23 e3dd6adc390e685985e5f40e6fe72df846a0acadc59ba15c208d9cb41732a663 30140 43100 1 0
This functionality is disabled be default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option. It should be
noted that this allows any process that has access to the wpa_supplicant
control interface to use PMKSA_ADD command to fetch keying material
(PMK), so this is for environments in which the control interface access
is restricted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These allow external program to monitor PMKSA cache updates in
preparation to enable external persistent storage of PMKSA cache.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Configuration file network block with disabled=2 is used for storing
information about a persistent group, so p2p_persitent_group should be
updated according to this when creating a struct wpa_ssid instance. This
will end up using D-Bus persistent network object path for the network.
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
Supported Operating Classes element and its use is define in the IEEE
802.11 standard and can be sent even when MBO is disabled in the build.
As such, move this functionality out from the CONFIG_MBO=y only mbo.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 192ad3d730 ('Interworking: Clear
SCANNING state if no match found') did this for the case where no
network matched credentials, but left the SCANNING state in place if
there were a match, but automatic connection was not enabled. Extend
this to cover the case where INTERWORKING_SELECT is not followed by a
connection attempt so that wpa_state is not left indefinitely to
SCANNING.
This fixes a hwsim test case failure in the following sequence:
ap_anqp_sharing scan_trigger_failure
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_s->sme.auth_alg could have been left to a previously value other
than WPA_AUTH_ALG_OPEN if IBSS network is used after an association that
used shared key, FT, or FILS authentication algorithm. This could result
in the IBSS setup failing due to incorrect authentication processing
steps.
Fix this by setting wpa_s->sme.auth_alg = WPA_AUTH_ALG_OPEN whenever
starting an IBSS (or mesh, for that matter) network.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 8e84921efe ('P2P: Support driver
preferred freq list for Autonomous GO case') introduced this loop to go
through preferred channel list from the driver. The loop does bounds
checking of the index only after having read a value from the array.
That could in theory read one entry beyond the end of the stack buffer.
Fix this by moving the index variable check to be done before using it
to fetch a value from the array.
This code is used only if wpa_supplicant is build with
CONFIG_DRIVER_NL80211_QCA=y and if the driver supports the vendor
extension (get_pref_freq_list() driver op). In addition, the driver
would need to return more than P2P_MAX_PREF_CHANNELS (= 100) preferred
channels for this to actually be able to read beyond the buffer. No
driver is known to return that many preferred channels, so this does not
seem to be reachable in practice.
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Commit 370017d968 ('P2P: Use preferred
frequency list from the local driver') introduced this loop to go
through preferred channel list from the driver. The loop does bounds
checking of the index only after having read a value from the array.
That could in theory read one entry beyond the end of the stack buffer.
Fix this by moving the index variable check to be done before using it
to fetch a value from the array.
This code is used only if wpa_supplicant is build with
CONFIG_DRIVER_NL80211_QCA=y and if the driver supports the vendor
extension (get_pref_freq_list() driver op). In addition, the driver
would need to return more than P2P_MAX_PREF_CHANNELS (= 100) preferred
channels for this to actually be able to read beyond the buffer. No
driver is known to return that many preferred channels, so this does not
seem to be reachable in practice.
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
This makes wpa_supplicant behavior more consistent with FLUSH command to
clear all state. Previously, it was possible for an ongoing scan to be
aborted when the FLUSH command is issued and the scan results from that
aborted scan would still be processed and that would update the BSS
table which was supposed to cleared by the FLUSH command.
This could result in hwsim test case failures due to unexpected BSS
table entries being present after the FLUSH command.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reject a passphrase with control characters instead of trying to write
out an example network configuration block with such control characters
included.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Skipping the scan altogether will hurt auto-reconnect. Also move the PNO
check down since the scan might be canceled for other reasons before we
defer it.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
The way the removal of duplicated (one per frequency) BSS entries in the
cfg80211 scan results were removed in driver_nl80211_scan.c
bss_info_handler() depended on having the full scan results available to
allow iteration through the other entries. This is problematic for the
goal of being able to optimize memory allocations for scan result
fetching in a manner that would not build the full result buffer in
memory.
Move this duplicate removal into bss.c since it has sufficient
information available for doing the same determination of which one of
two BSS entries is more current.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_priv did not yet support Beacon frame IEs (res->beacon_ie_len) which
resulted in invalid scan data being accepted in driver_privsep.c. Add
support for res->beacon_ie_len and also fix the validation step to take
this new variable length field into account.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_priv has never really been fully up-to-date with the wpa_supplicant
driver interface extensions. This does not seem like something that
would change in the future either, so document this reduced
functionality as a potential drawback.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids a theoretical resource leak on exit path if wpa_priv is
killed while there is a wpa_supplicant process using it.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids some valgrind warnings about use of uninitialized memory in
cases where a struct may have padding octets between the fields.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of some dependencies on how extra octets at the end of the
struct sockaddr_un get "uninitialized" consistently by only using the
exact length of the address data from the recvfrom() call. This resolves
number of valgrind warnings about use of uninitialized memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to be able to work with many wpa_supplicant use cases,
e.g., due to use of TDLS or RSN pre-authentication needing a separate
l2_packet socket.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit enhances the existing implementation of abort scan to also
abort concurrent active vendor scans. This is achieved by passing the
the scan_cookie to the driver interface with the intention to abort
the specific scan request. This scan_cookie is returned from the driver
interface when the scan request is scheduled.
This scan_cookie is 0 if the scan is triggered through the upstream
cfg80211 interface. Thus, the scan_cookie is used to determine whether
to abort the cfg80211 or vendor scan request.
Also, the previous implementation of relying on scan_work/p2p_scan_work
for the active work to trigger the abort scan is enhanced to check for
the started state of either of these work operations. This should also
help to abort the concurrent active scan/p2p-scan operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit enhances the abort scan implementation to also abort the
vendor scan, if one was used to trigger the scan.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
cfg80211 rejects the scans issued with random MAC address if the STA is
in connected state. This resulted in failures when using MAC_RAND_SCAN
while connected (CTRL-EVENT-SCAN-FAILED ret=-95). Enable random MAC
address functionality only if the STA is not in connected state to avoid
this. The real MAC address of the STA is already revealed in the
association, so this is an acceptable fallback mechanism for now.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds IP address information into GroupStarted event on the
P2P client side like it is sent over the control interface.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
Previously, wpa_supplicant only supported hardcoded port == 1 in the
SCI, but users may want to choose a different port.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
So that the user can turn encryption on (MACsec provides
confidentiality+integrity) or off (MACsec provides integrity only). This
commit adds the configuration parameter while the actual behavior change
to disable encryption in the driver is handled in the following commit.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This enables configuring key_mgmt=NONE + mka_ckn + mka_cak.
This allows wpa_supplicant to work in a peer-to-peer mode, where peers
are authenticated by the pre-shared (CAK,CKN) pair. In this mode, peers
can act as key server to distribute keys for the MACsec instances.
This is what some MACsec switches support, and even without HW
support, it's a convenient way to setup a network.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
BoringSSL is the only supported version of SSL, so remove this guard so
we can continue to compile when the flavor.mk is removed.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This provides more details on BSS selection process in the debug log.
Previously, the BSSs that were not either the current or the selected
one were not necessarily printed at all. Now all BSSs that match the
currently selected network are listed with their frequency and signal
strength details.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the estimated throughput was used to enable roaming to a
better AP. However, this information was not used when considering a
roam to an AP that has better signal strength, but smaller estimated
throughput. This could result in allowing roaming from 5 GHz band to 2.4
GHz band in cases where 2.4 GHz band has significantly higher signal
strength, but still a lower throughput estimate.
Make this less likely to happen by increasing/reducing the minimum
required signal strength difference based on the estimated throughputs
of the current and selected AP. In addition, add more details about the
selection process to the debug log to make it easier to determine whaty
happened and why.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, CONFIG_IEEE80211R enabled build that supports FT for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode FT is required and there is no need for AP mode FT.
Add support to differentiate between station mode FT and AP mode FT in
wpa_supplicant builds by adding CONFIG_IEEE80211R_AP that should be used
when AP mode FT support is required in addition to station mode FT. This
allows binary size to be reduced for builds that require only the
station side FT functionality.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
CONFIG_MBO was defined inside ifdef CONFIG_AP, so when AP support
was not compiled, MBO was not compiled either. However, CONFIG_MBO
is not related AP support, so it should not depend on CONFIG_AP.
Fix this by moving CONFIG_MBO outside of ifdef CONFIG_AP.
Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
