This commit enhances QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES to
also be an event, aimed to notify the link status (EX: connected
stations status on an AP link).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG vendor command
to set the priorities among different types of traffic of
WLAN/BT/Zigbee during coex scenarios.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add interface for drivers to report changes in TX/RX throughput
dynamically to user space. This information can be used by userspace
tools to tune kernel's TCP parameters in order to achieve peak
throughput. The driver may optionally provide guidance on which TCP
parameters to be configured for optimal performance along with the
values to be configured.
The TCP parameters that need to be tuned for peak performance are not
interface specific. Based on the guidance from the driver and
considering the other interfaces that may be affected with the new
configurations, a userspace tool has to choose the values to be
configured for these parameters to achieve optimal performance across
interfaces.
The throughput levels informed by the driver with this event are only
for providing guidance on TCP parameter tuning from userspace. The
driver may change the thresholds used to decide low or medium or high
throughput levels based on several parameters based on the PHY layer
capacity in the current connection, the number of packets being
dispatched per second, or the number of packets pending in queues, etc.
The throughput levels may not be consistent with the actual throughput
of the link.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure action
frame transmission in HE trigger based PPDU.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure HE
single user PPDU transmission.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attributes to configure HE
operating mode control field bandwidth, number of spatial streams, and
UL MU disable configuration. Define a new attribute to clear the
previously set HE OM control field configuration. This is used for
testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add NAN NDP attribute QCA_WLAN_VENDOR_ATTR_PEER_NDPE_SUPPORT which
indicates if NDP remote peer supports NDPE attribute or not.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a subcommand for Channel Frequency Response (CFG) Capture
Configuration and define attributes for configuring CFR capture
parameters per peer and enabling/disabling CFR capture.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Driver/firmware does roam scan when it finds the need to roam to a
different BSS. Add a QCA vendor event to indicate such roam scan events
from driver/firmware to user space.
Please note that some drivers may not send these events in few cases,
e.g., if the host processor is sleeping when this event is generated in
firmware to avoid undesired wakeups.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new QCA vendor specific test config attribute to configure the
support for receiving the MPDU with operating mode control subfield.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The payload used for the existing NAN vendor command,
QCA_NL80211_VENDOR_SUBCMD_NAN is a binary blob of data. This
command is not extendable to send additional information. Hence
define a new vendor command QCA_NL80211_VENDOR_SUBCMD_NAN_EXT,
that can carry the binary blob encapsulated within an attribute
and can carry additional attributes to enhance the NAN command
interface. Define additional 3 new attributes for conveying
type of NAN subcmd and channel information.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Present implementation of NAN vendor command does not use
attribute encapsulation for sending the command from userspace
to the driver, payload is directly sent as is. Attribute
QCA_WLAN_VENDOR_ATTR_NAN is used only for receiving vendor
events in the userspace from the driver. Update the doc as per
this implementation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The max supported ADDBA buffer size value is 256, so change
the buffer size attribute type to U16 to configure the testbed
device to use the 256 buffer size in ADDBA negotiation in 11ax
testing.
This attribute is used only to configure a testbed device and the old
definition of this attribute was not used in any deployed implementation
hence it is still justifiable to change the definition.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_GSCAN_MAX_BLACKLIST_BSSID to get maximum
blacklist BSSIDs capability from the driver for gscan.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new test config QCA vendor attribute to override the MU EDCA
parameters to default values in the driver for test configuration. This
is used for configuring the testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure HE
trigger frame MAC padding duration value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attributes to configure
HE MU EDCA parameters value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure Tx
beamformee number of space-time streams value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit adds a new vendor command attribute
QCA_WLAN_VENDOR_ATTR_CONFIG_GTX in
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION to enable/disable green
Tx power saving feature.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add NAN attributes to communicate IPv6 address, port, and protocol
between wifihal and host driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Over time a number of style issues have crept into qca-vendor.h,
so fix most of them. There are some identifiers and comments which
exceed 80 columns, but these are left as-is for readability.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This can be used to determine which mechanism to use for configuring
country code from trusted sources.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure Tx
beamformee in the driver. This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add commands to allow an AP to configure filtering rules to capture
frames from stations that are active on the operating channel, but
not associated to this AP. Operations include add/delete the filter
and get the statistics information of the unassociated stations.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Add a new wifi test config attribute to configure HE LTF in the
driver. This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new WiFi test configuration attributes in QCA vendor
command to configure BA session parameters and to add or
delete a BA session and to configure no ack policy.
This is used for configuring the testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new WiFi test configuration attribute in QCA vendor
command to allow or not to allow WEP/TKIP in HT/VHT/HE mode.
This is used for configuring the testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enhance QCA vendor specific APF interface to support write/read program
and/or data and to enable/disable APF feature.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new QCA vendor sub command for configuring the device with wifi
test configuration. Add new test config attributes for this sub command
that are used to configure the device for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new QCA vendor commands and attributes to get thermal information
and send thermal shutdown related commands. Indicates the driver to
enter the power saving mode or resume from the power saving mode based
on the given temperature and thresholds.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add additional NDP attributes and NDP subcommand value which is
provided as part of schedule update indication from driver/firmware
to HAL.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allow MSDU queue depth threshold in target to be set per peer per
TID. This command contains MAC address, TID, update mask, and threshold
values.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit extends the existing QCA vendor specific NUD_STATS_GET/SET
interface to also collect the statistics of the data packets. The
intention here is to get more comprehensive information to detect the
network unreachability.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit introduces a QCA vendor command that provides the current
information of WLAN hardware MAC and its associated WLAN netdev
interfaces.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
A new vendor attribute QCA_WLAN_VENDOR_ATTR_GET_WEIGHED_PCL is added for
getting preferred channels with weight value and a flag to indicate how
the channels should be used in P2P negotiation process.
Signed-off-by: Peng Xu <pxu@qti.qualcomm.com>
Indicates the driver to use the RSNE as-is from the connect interface.
Exclusively used for the scenarios where the device is used as a testbed
device with special functionality and not recommended for production.
This helps driver to not validate the RSNE passed from user space and
thus allow arbitrary IE data to be used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously commit c79238b6a4 ('Define a
QCA vendor command to configure SAR Power limits') implemented a vendor
command interface to allow a userspace entity to dynamically control the
SAR power limits. Now implement a command to retrieve the current SAR
power limits.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A new vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL is added
for vendor sub-command QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION.
This attribute is for setting the level of WLM.
Signed-off-by: Paul Zhang <paulz@qti.qualcomm.com>
Add QCA vendor command and attributes for vendor specific Representative
RF Operating Parameter (RROP) information. This information is intended
for optional use by external ACS. It provides guidance values for some
RF parameters that are used by the system during operation, so that
external ACS can utilize these to compare between channels, bands, etc.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Fix the block comment style issue introduced as part of commit
fbfceef3af ("Add QCA vendor commands for
spectral scan").
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add sub-command QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING to flush
pending packets in firmware. The attributes are listed in enum
qca_wlan_vendor_attr_flush_pending. The QCA_WLAN_VENDOR_ATTR_PEER_ADDR
specifies the peer MAC address and the QCA_WLAN_VENDOR_ATTR_AC specifies
the access category of the pending packets.
Signed-off-by: Lin Tingting <tinlin@qti.qualcomm.com>
A new vendor attribute QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_PENDING_MSDU
is added for vendor sub-command QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET.
This attribute is for pending MSDUs corresponding to respective AC.
Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
Add the following vendor commands and their vendor attributes for
spectral scan.
1) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG
Get current values of spectral parameters.
2) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS
Get stats for spectral scan debug.
3) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO
Get the spectral hardware capability.
4) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS
Get the current status of spectral scan.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME
and QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME to record
timestamp and duration for the last MAC counters. Some user layer
application is delay sensitive. It needs to know time stamp and
measurment duration for the counters.
Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
Add additional attributes to specify the PMK, PMKID, and the ERP next
sequence number to the vendor subcommand
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH. These are needed in case
of an offloaded FILS roaming.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
