Add support for per-MLO link configurations in
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION commands.
Additionally, add documentation for
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION commands.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Define a new QCA vendor test config attribute to configure powersave
on MLO links.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend bitwise mask in enum qca_wlan_tdls_caps_features_supported to get
the TDLS wider bandwidth capability from the driver.
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
Use zero value with QCA_WLAN_VENDOR_ATTR_CONFIG_EHT_MLO_MAX_NUM_LINKS to
restore the device default maximum number of allowed MLO links
capability.
Also, as per IEEE 802.11be/D3.0, the maximum number of allowed links for
an MLO connection is 15. Update the documentation of the attribute to
indicate the same.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Define a QCA vendor command to configure MLO link id to the driver on
which the TDLS discovery response frame needs to be transmitted when the
local station is connected in MLO mode. This command is configured to
the driver the prior to every TDLS discover frame transmission when the
station is connected in MLO mode. If the station is connected in non-MLO
mode this command is not configured to the driver for TDLS discovery
frame transmission.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new vendor command and attributes to notify TID-to-link mapping
changes to the userspace.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Define a new QCA vendor attribute to configure channel bandwidth to the
driver for CTS frame transmission. This is used for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN in
enum qca_wlan_vendor_features to indicate the device supports enhanced
audio experience over WLAN feature.
Also, update the documentation where other subcommand(s) or attribute(s)
require this new feature flag. These subcommand(s) and attributes are
under development and would be restricted to the supported drivers
advertising QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN.
As such, it is still acceptable to introduce a new requirement for the
previously defined interface.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Add vendor attributes for EHT testbed STA configuration.
This includes enabling STR MLMR mode and forcing power save
on active MLO links for a defined number of beacon periods.
Signed-off-by: Gururaj Pandurangi <quic_panduran@quicinc.com>
Add vendor attributes related to MLO and EMLSR mode
capability configuration for EHT testbed STA. It includes
EHT OM control support and EMLSR padding delay configuration.
Also, generalise the naming of HE OMI control enumeration to
OMI control as it now consists of both HE and EHT OMI control
fields.
Signed-off-by: Gururaj Pandurangi <quic_panduran@quicinc.com>
Add vendor attributes related to MLO and EMLSR mode
capability configuration for EHT DUT. This includes forcing
active MLO links and invoking EMLSR mode entry or exit.
Signed-off-by: Gururaj Pandurangi <quic_panduran@quicinc.com>
IEEE 802.11be enables multiple links between STA and AP. Each of the
link has its own set of statistics. Add additional attributes required
to fetch link layer statistics per MLO link.
For MLO connection, per MLO link statistics will be sent with the new
attribute QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. Also, cumulative
statistics of all the MLO links will be sent outside
QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK to be compatible with legacy user
space.
For non-MLO connection, the statistics will be sent without being nested
inside QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK attribute.
Co-authored-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
The attributes QCA_WLAN_VENDOR_ATTR_LL_STATS_PAD and
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NF_CAL_VAL were allocated the same
attribute number in error. QCA_WLAN_VENDOR_ATTR_LL_STATS_PAD attribute
is known to not be used; thus, it is safe to be renumbered.
Fixes: 1491fc64a8 ("Define QCA vendor per-enum 64-bit pad attributes")
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
When user space triggers a scan, the firmware aborts background scan,
and uses the roam status QCA_ROAM_FAIL_REASON_CURR_AP_STILL_OK instead
of "Invalid roam failures reason".
Signed-off-by: Chunquan Luo <quic_chunquan@quicinc.com>
Define bitmap values used by LL_STATS vendor command
and update the corresponding kernel documentation.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a vendor feature flag for the driver to indicate support for allowed
frequency configuration in AP mode.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add a new vendor command to trigger computation of connected channel
statistics such as channel utilization in STA mode.
Signed-off-by: Ainy Kumari <quic_ainykuma@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Define a new attribute QCA_WLAN_VENDOR_ATTR_CONFIG_AP_ALLOWED_FREQ_LIST
to configure the full list of allowed frequencies for the AP operation.
The configuration is valid only from the next BSS start until the BSS is
stopped. The drivers shall filter out channels on top of this list of
channels based on regulatory or other constraints. This can be used to
specify user's choice of frequencies, allowed list of channels with
static puncturing feature, etc.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Extend QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_WIDTH to configure 320 MHz
bandwidth to the driver/firmware.
Signed-off-by: Ainy Kumari <quic_ainykuma@quicinc.com>
When writing 64-bit attributes into the netlink buffer, senders may
add a padding attribute to allow the payload of the 64-bit attribute
to be 64-bit aligned. For QCA vendor attributes, currently the
attribute QCA_WLAN_VENDOR_ATTR_PAD in enum qca_wlan_vendor_attr is
defined for this purpose.
Unfortunately, when adding attributes to the netlink buffer, all
attributes at a given level of nesting must be defined in the same
enum so that they can be unambiguously parsed. This means that
QCA_WLAN_VENDOR_ATTR_PAD can only be used to pad 64-bit attributes
defined in enum qca_wlan_vendor_attr.
There are many other QCA vendor enums which define 64-bit attributes,
so add a pad attribute to all of them so that the 64-bit attributes
can be unambiguously padded.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Add a new vendor command and attributes to control and fetch the state
information of the MLO links affiliated with a specific interface.
This will enable user space to dynamically control the MLO links states
based on the latency, throughput and power save requirements.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Add QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_LOW_LATENCY attribute
to enable/disable Multi-Channel concurrency low latency mode.
The firmware will do optimization of channel time quota for
low latency in Multi-Channel concurrency state if enabled.
Signed-off-by: Liangwei Dong <quic_liangwei@quicinc.com>
During implementation of commit 257b119c2d ("QCA vendor attribute of
update roaming cached statistics info") some deficiencies were noted as
listed below, so fix them. Since these are pre-implementation changes,
no ABI breakage is introduced.
1) Change all RSSI values to be signed values.
2) Add enums for scan type and dwell type instead of documenting
their values with comments
3) Add missing QCA_ROAM_REASON_STA_KICKOUT to enum qca_roam_reason
Signed-off-by: Chunquan Luo <quic_chunquan@quicinc.com>
Add vendor subcmd QCA_NL80211_VENDOR_SUBCMD_ROAM_STATS and attribute id
in enum qca_wlan_vendor_attr_roam_cached_stats for collecting roaming
statistics information when diagnosing roaming behavior.
Signed-off-by: Chunquan Luo <quic_chunquan.quicinc.com>
Add new AP concurrency policy QCA_WLAN_CONCURRENT_AP_POLICY_XR to
configure interface for eXtended Reality (XR) requirements.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Add a new vendor command QCA_NL80211_VENDOR_SUBCMD_GET_MONITOR_MODE to
get the local packet capture status in the monitor mode. Add required
attributes to respond with status of the monitor mode. The monitor mode
can be started/configured by using the
QCA_NL80211_VENDOR_SUBCMD_SET_MONITOR_MODE subcommand.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Add new QCA vendor attributes to configure the driver for EHT
capabilities and multi link configuration.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add new QCA vendor attributes to configure the driver for EHT
capabilities. These attributes are used for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add new attributes for the destination MAC address and netdev index in
SCS rule config subcommand.
Signed-off-by: Harsh Kumar Bijlani<quic_hbijlani@quicinc.com>
Add QCA_WLAN_VENDOR_ATTR_CONFIG_WFC_STATE vendor attribute. Userspace
uses this attribute to configure wfc state to the driver/firmware. The
driver/firmware uses this information to optimize power savings, rate
adaption, roaming, etc.
Signed-off-by: Mukul Sharma <quic_mukul@quicinc.com>
Add a new subcommand QCA_NL80211_VENDOR_SUBCMD_DOZED_AP to configure
doze mode state on an AP interface. This is also used as an event to
indicate the updated configuration. In doze mode, AP transmits
beacons at higher beacon intervals and RX is disabled.
Uses attributes defined in enum qca_wlan_vendor_attr_dozed_ap.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
During the roam scan, if there are no desired APs found in the partial
frequency list, an immediate full scan on all the supported frequencies
is initiated as a fallback. This would include the 6 GHz PSC
frequencies. Define an attribute to allow that behavior to be modified
to include PSCs only if 6 GHz use has been detected.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
During the roam scan, if there are no desired APs found in the partial
frequency list, an immediate full scan on all the supported frequencies
is initiated as a fallback. This flag controls the frequency list
creation for full scan on the following lines.
1 - Full scan to exclude the frequencies that were already scanned by
the previous partial scan.
0 - Full scan to include all the supported frequencies irrespective of
the ones already scanned by partial scan.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wi-Fi Alliance specification for Automated Frequency Coordination (AFC)
system ensures that the Standard Power Wi-Fi devices can operate in 6
GHz spectrum under favorable conditions, without any interference with
the incumbent devices.
Add support for vendor command/events and corresponding
attributes to define the interface for exchanging AFC requests and
responses between the driver and a userspace application.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new vendor subcommand
QCA_NL80211_VENDOR_SUBCMD_MLO_PEER_PRIM_NETDEV_EVENT to send notification
to application layer about primary netdev of an MLO peer association.
Also define the attributes present in this subcommand.
Signed-off-by: Krunalsinh Padhar <quic_kpadhar@quicinc.com>
Introduce a run time roam configuration for "hand off delay for RX".
This value, in milliseconds, will delay the hand off for the specified
time to receive pending RX frames from the current BSS.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This was supposed to update the requested value to the next available
one, not to duplicate the already assigned value.
Fixes: b17b86da47 ("QCA vendor attribute to configure periodic sounding")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new QCA vendor attribute to configure the periodic sounding
for Tx beamformer functionality.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support for new vendor sub-command attributes for 320 MHz
channel width and puncturing information as part of the
external ACS.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Introduce a new attribute to configure access category
override for UDP frames of BE/BK category. Unlike, the
earlier attribute QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE
which will override for all UDP frames, this attribute is
for overriding only for BE/BK based UDP frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add service class id attribute
QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_SERVICE_CLASS_ID in SCS rule
configuration vendor subcommand
QCA_NL80211_VENDOR_SUBCMD_SCS_RULE_CONFIG.
Signed-off-by: Harsh Kumar Bijlani<quic_hbijlani@quicinc.com>
Add a new vendor sub-command to implement Spatial Reuse feature.
Userspace enables SR feature with specific configuration parameters. The
driver/firmware upon receiving the command, enables the SR feature if it
is supported by the currently connected AP. The driver may reject the
command if it cannot enable the SR with the configured parameters. The
driver sends events to userspace to indicate when SR feature is enabled
or disabled internally. Userspace can also query SR feature related
parameters and statistics from the driver/firmware as needed.
Signed-off-by: Rachit Kankane <quic_rkankane@quicinc.com>
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
