Currently the moderate latency level is not used. Rename the moderate
latency level to XR latency level to be used in XR (extended reality)
applications.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend the peer queue flush command with following attributes
1. Enable to flush per TID peer queue
2. Enable to configure when to flush the peer/TID queue
Signed-off-by: Madhvapathi Sriram <quic_msriram@quicinc.com>
Replace the word "blacklist" with the inclusive word "denylist" and add
aliases for backward compatibility.
Signed-off-by: Arowa Suliman <arowa@chromium.org>
Replace the word "whitelist" with the inclusive word "allowlist" and add
aliases for backward compatibility.
Signed-off-by: Arowa Suliman <arowa@chromium.org>
Add a QCA vendor netlink interface to start/stop periodic TSF sync
feature and also support configuration of interval value as part of TSF
sync start command. In addition, improve documentation for the related
attributes and values.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add QCA_WLAN_VENDOR_ATTR_ACS_EHT_ENABLED flag attribute to conduct ACS
for EHT mode. The driver can consider EHT specific parameters such as
puncture pattern for ACS when this flag attribute is indicated by
userspace.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add additional attributes in
QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT vendor sub command to
avoid usage of unsafe frequencies on wifi interfaces sent from userspace
to the driver/firmware. The driver/firmware shall use restrictions and
power cap accordingly to restrict the usage of these frequencies on
operating interface(s).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a QCA vendor attribute to indicate the puncture pattern derived
by the automatic channel selection algorithm.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the attribute QCA_WLAN_VENDOR_ATTR_SCAN_PRIORITY to configure the
priority of vendor scan relative to other scan requests. Add the valid
values that this attribute can take.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to indicate agile spectral scan support for
320 MHz mode. Add another attribute to indicate the number of detectors
used for spectral scan in 320 MHz mode.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce a new vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS
that aims to configure/trigger the roam events from the driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This new vendor command aims to indicate the driver to enable the
monitor mode for an interface on which this command is issued. Once
enabled, the frames (both TX and RX) on this interface are sent to an
active coexisting monitor interface.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new attributes for supporting MBSSID multi groups notifications
to qca_wlan_vendor_attr_mbssid_tx_vdev_status
(QCA_NL80211_VENDOR_SUBCMD_MBSSID_TX_VDEV_STATUS).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
QCA_ROAM_REASON_USER_TRIGGER was wrongly documented as
QCA_ROAM_REASON_EXPLICIT_REQUEST, so correct it.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor interface support for configuring background scan related
parameters to the driver/firmware.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new attribute into qca_wlan_vendor_attr_ll_stats_results to
support getting interface time slicing duty cycle info.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver/firmware the allowed
bands for roaming by userpace. This attribute is also used to get the
configured roam bands from the driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA new status vendor attribute
QCA_WLAN_VENDOR_TWT_STATUS_POWER_SAVE_EXIT_TERMINATE
to indicate the TWT session termination due to power save
exit request from userspace.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the following vendor attribute to indicate the bandwidth to be used
for spectral scan operation:
- QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BANDWIDTH
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enhance QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD to fetch thermal
statistics for different temperature levels from the driver to
userspace. The statistics will be stored in the driver/firmware for
predefined temperature levels and will be reported to userspace when
QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD is sent with the command type
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_THERMAL_STATS.
The thermal statistics can be cleared from userspace by sending a
QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD command with the type
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_CLEAR_THERMAL_STATS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor attributes to configure the driver to enable/disable the
Broadcast TWT support and Rx Control Frame To MultiBSS support in HE
capabilities information field. This attribute is used for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME_TSF
TWT attribute to use it in TWT setup command to pass TSF value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new QCA vendor attribute to configure the driver to enable/disable
the BSS max idle period support. This attribute is used for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver to use scan
request BSSID value in Probe Request frame RA(A1) for scan.
This attribute is used for testing purpose.
The driver saves this configuration and applies this setting to all user
space scan requests until the setting is cleared. If this configuration
is set, the driver uses the BSSID value from the scan request to set the
RA(A1) in the Probe Request frames during the scan, else the broadcast
address is set in the Probe Request frames RA(A1).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor interface to configure the driver which transport mode to
use for sending CFR data to userspace. Currently, relayfs and netlink
event modes are supported.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Add a QCA vendor attribute to configure the driver to use Data or
Management frames for keep alive data. This attribute is used for
testing purpose.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor attribute to configure the driver to transmit the
Data frames with ER SU PPDU type format. This attribute is used
for testing purpose.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_FT_OVER_DS
to configure FT over DS to the driver/firmware.
Signed-off-by: Vinita S. Maloo<vmaloo@codeaurora.org>
Add QCA interface to specify the RSSI thresholds separately for candidate
APs from different bands.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Mention that for AP mode this attribute is required in
response for TWT SET, TWT GET, TWT SUSPEND, and TWT
TERMINATE. And is required in request for TWT GET, and
TWT TERMINATE.
For STA mode, the usage of this attribute remains unchanged.
Signed-off-by: Mohammad Asaad Akram <asadkrm@codeaurora.org>
Add QCA vendor interface for userspace to get information of usable
channels for different interface types from the driver/firmware.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
The firmware rejects the TWT setup request when scan is in
progress. Extend enum qca_wlan_vendor_twt_status to represent new
reason code for it.
Signed-off-by: Mohammad Asaad Akram <asadkrm@codeaurora.org>
Define a new reason code in enum qca_wlan_vendor_hang_reason,
QCA_WLAN_TASKLET_CREDIT_LATENCY_DETECT, for tasklet/credit latency
detection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce a QCA vendor command to configure the concurrent connection
policies when multiple STA interfaces are (getting) active.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the new TWT attributes for configuring the broadcast TWT
parameters in enum qca_wlan_vendor_attr_twt_setup.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The firmware rejects the TWT setup request when roaming and channel
switch is in progress. Extend enum qca_wlan_vendor_twt_status to
represent new reason codes for these cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The firmware sends new reason codes to indicate TWT teardown due to
single channel and multi channel concurrency. Update the enum
qca_wlan_vendor_twt_status to represent new reason code.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the following additional TWT attribute for
qca_wlan_vendor_attr_twt_setup:
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL2_MANTISSA to configure the
mantissa in microseconds.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
