It is possible to execute the tests directly inside the a VM without
necessarily running the repository wrapper script to do so. In these
cases, passing the VM flag using an environment variable allows
correctly flagging this fact to the tests.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
The regulatory domain cannot be reset while the AP is still active. Add
the appropriate commands to bring down the AP after the test, which will
also make resetting the regulatory domain work.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
pyrad does an internal call to getaddrinfo with the service "www".
Make sure this service is known by writing an appropriate
/etc/services file.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
pyrad internally uses socket.getaddrinfo. While it is documented that
one can pass an empty string to bind to all interfaces. The underlying
function expects None instead though, breaking the call.
Either way, it does not hurt to set the bind address to 127.0.0.1
explicitly, so do so to avoid issues.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
It seems that the messages from ip may have a trailing space in some
cases, which may break matching in surrounding logic. Strip the output
to remove whitespace and avoid any issues this may cause.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Extend the previously used minimal test case with full validation of the
selected channel and connection since hostapd now has support for the
HT40- case as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
With UML time-travel, it was possible for a GAS frame to end up in the
capture file for the next test case and if that next case used tshark to
count the number of frames (which is done, e.g., in
gas_anqp_address3_assoc), the following test case could have indicated
failure even when everything worked correctly.
Signed-off-by: Jouni Malinen <j@w1.fi>
The cfg80211 default QoS mapping might be updated to align with the
recommendations in section 4 in RF C8325. Align the QoS mapping tests
accordingly. For now, allow both the previous and new mapping to pass
the test.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add a simple test that exemplifies TX power configuration when operating
on the 6 GHz band.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Some of these can take close to the previously used timeouts and this
could result in reporting failures in cases that worked fine.
Signed-off-by: Jouni Malinen <j@w1.fi>
Test EHT connection on the 5 GHz band with channel bandwidths 20-160 MHz
and up to 320 MHz on the 6 GHz band.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This avoids issues with old scan results from a previous test causing
incorrect association after WPS exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The previous timeout allowed only a single chirping round, and sometimes
not even that full round. That resulted in test failures for cases where
there was not really any incorrect behavior.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Stop dev[0] from trying to associate at the end of the test case to
reduce risk for leaving out some pending operations that could mess up
the following test case.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Handle the cases where the first attempt to start scan fails due to an
ongoing scan. Stop such scan and try again instead of failing the test
case immediately.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This avoids race conditions with UML time-travel where some cases ended
up not reporting the DPP-TX-STATUS event and that resulted in discarding
events that are more important to verify for correct behavior.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
One of the sigma_dut testing cases missed the t.join() call to make
surte the separate thread terminated. This could result in confusing
"unexpected stdout output" in a middle of an unrelated test case.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Stop and restart P2P_FIND on dev[1] to avoid timing issues where the
wait on dev[1] makes the test case fail even though this was trying to
verify that dev[0] is reacting quickly enough.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wait a bit between the DPP-SCAN-PEER-QR-CODE event and reporting of the
QR Code to avoid a race condition.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Avoid a race condition that could result in the relay (hostapd)
maintaining STA association with PMF and discarding of the GAS frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Terminate the group explicitly before cleanup to avoid a race condition
between an automatically started scan to find the GO again and the scan
started to clear the scan cache.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wait a bit to allow stopping of the DPP_LISTEN operation to be completed
before issuing the DPP_QR_CODE command that would send the frame that
these test cases expect to not get ACKed.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wait some time between the first DPP Authentication Response that
indicates the response is not yet available and the second DPP
Authentication Response to make this sequence a bit more realistic and
less likely to hit race conditions with UML time-travel.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait for hostapd to complete STA authorization before running the
connectivity test between two associated STAs.
Signed-off-by: Jouni Malinen <j@w1.fi>
It can take significant amount of time to find the peer in this type of
a case where an AP connection is forced on a different channel while
going through p2p_find on both devices.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
