That wpa_supplicant header file is not needed for driver_atheros.c and
maybe was never really needed, so do not include it here to avoid
potentially conflicting C preprocessor defines.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is helpful for understanding why an assocation attempt takes
unexpectedly long time to complete.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Check driver support for SA Query offload in AP mode and skip starting
SA Query timer on CSA for OCV enabled STAs when the driver indicates
support for offloading SA Query procedures.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This brings in nl80211 definitions as of 2022-01-04. In addition, update
nl80211_command_to_string() to cover the new defined commands.
Signed-off-by: Jouni Malinen <j@w1.fi>
Now that wpa_supplicant does this internally as a part of the FLUSH
command, there is no need for the test scripts to try to clear the
parameter between test cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The hwsim test cases are trying to clear this parameter between test
cases, but that was not really done correctly for many of the sigma_dut
test cases. Instead of fixing the text scripts to do this more
carefully, it seems to be simpler to just force the FLUSH command to
clear this.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This test case could fail in some sequences like "sigma_dut_sae
scan_parsing" due to the ignore_old_scan_res parameter accidentally
being left to 1 by the former test case and the simulated scan result
being older than the previous scan trigger. Reduce the age of that scan
entry to make this less likely to happen.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add QCA_NL80211_VENDOR_SUBCMD_MCC_QUOTA. When two or more interfaces are
active on the same band and two different home channels (MCC), the
target may allocate quota of "on channel" time for each home channel.
The target will indicate the quota information to application layer with
this event. Application may do TX bitrate control based on the
information. The user may also set the MCC quota for an interface by
using this command.
Signed-off-by: Liangwei Dong <quic_liangwei@quicinc.com>
Signed-off-by: Madhvapathi Sriram <quic_msriram@quicinc.com>
Introduce a new vendor command
QCA_NL80211_VENDOR_SUBCMD_RATEMASK_CONFIG. This is used to set the rate
mask config to be used in MCS rate selection per PHY type.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Currently the moderate latency level is not used. Rename the moderate
latency level to XR latency level to be used in XR (extended reality)
applications.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Not doing this was resulting in test failures with many sequences of a
mesh test case (e.g., wpas_mesh_peer_connected) followed by
ap_csa_1_switch which was checking the driver wrapper frequency
information at the beginning.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is needed since the gas_query_req() operation could remain waiting
indefinitely for the response if the Configurator keeps sending out
comeback responses with additional delay. The DPP technical
specification expects the Enrollee to continue sending out new Config
Requests for 60 seconds, so this gives an extra 60 second time after the
last expected new Config Request for the Configurator to determine what
kind of configuration to provide.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
DPP Enrollee might wait for the configuration for 60 seconds, so
increase the DPP Configurator timeout for the GAS server operation to 60
seconds to cover that full wait time. This is needed for cases where
user interaction can take significant amount of time before the
configuration response can be generated.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Instead of depending on the TX-wait-response-time to be sufficient to
cover the full GAS exchange, start an ongoing listen operation on the
negotiation channel (if no such listen operation is already in place) to
allow the configuration exchange to take longer amount of time. This is
needed for cases where the conf=query is used to request Configurator
parameters from upper layers and that upper layer processing (e.g., user
interaction) takes significant amount of time.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The DPP Enrollee might wait for up to 60 seconds for the configuration,
so use a longer timeout value to be able to cover this negative test
case where the Configurator never sends the response.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This can be helpful in figuring out when the driver has stopped waiting
on a specific channel and would need a remain-on-channel command to
continue listening on that channel.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Once the GO/AP interface initialization is completed, check if the
operating frequency set in the wpa_supplicant group interface structure
is different than the one set in the hostapd interface structure
associated with the group interface. If yes, update the frequency in the
wpa_supplicant group interface and network configuration to the
frequency set in the hostapd interface structure.
The frequency set in the hostapd interface is the correct/final
frequency wpa_supplicant configured in the kernel/driver. This is done
because wpa_supplicant may switch the initially requested primary and
secondary frequencies to get a secondary frequency with no beacons (to
avoid interference or 20/40 MHz coex logic). And the updated frequency
is informed by the driver only after the interface setup is completed
through the channel switch event - EVENT_CH_SWITCH. But wpa_supplicant
updates the frequency to applications through the P2P_GROUP_STARTED
event which is triggered before the EVENT_CH_SWITCH event. To send the
correct frequency to applications the frequency must be updated before
sending the P2P_GROUP_STARTED event.
Bug: 191272346
Test: Manual - Verified that GO frequency is updated and reported
correctly to Nearby application.
Signed-off-by: Sunil Ravi <sunilravi@google.com>
This provides an alternative mechanism for upper layer components to
control configuration parameters to be used by the local Configurator.
Instead of the previously used design where the Configurator parameters
had to be provided before initiating the DPP Authentication exchange,
the new alternative approach allows the DPP Authentication exchange to
be started before any Configurator parameters have been determined and
wpa_supplicant will then request the parameters once the DPP
Configuration Request has been received from the Enrollee. This allows
the Config Request information to be used at upper layers to determine
how the Enrollee should be configured.
For example for an Initiator:
CTRL: DPP_QR_CODE <URI from Responder/Enrollee>
CTRL: DPP_AUTH_INIT peer=1 conf=query
<3>DPP-CONF-NEEDED peer=1 src=02:00:00:00:00:00 net_role=sta name="Test" opclass=81,82,83,84,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130 mud_url=N/A
(upper layer processing; potentially including user interaction)
CTRL: DPP_CONF_SET peer=1 conf=sta-sae ssid=736165 pass=70617373776f7264
<3>DPP-CONF-SENT
For example for a Responder:
CTRL: SET dpp_configurator_params conf=query
CTRL: DPP_LISTEN 2412 role=configurator
<3>DPP-CONF-NEEDED peer=2 src=02:00:00:00:01:00 net_role=sta name="Test" opclass=81,82,83,84,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130 mud_url=N/A
(upper layer processing; potentially including user interaction)
CTRL: DPP_CONF_SET peer=2 conf=sta-sae ssid=736165 pass=70617373776f7264
<3>DPP-CONF-SENT
For example for an Initiator that can act both as a Configurator and an
Enrollee in a case where the Initiator becomes the Enrollee:
CTRL: DPP_AUTH_INIT peer=1 role=either conf=query
<3>DPP-CONF-RECEIVED
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend the GAS server functionality to allow a request handler to return
the initial comeback delay with a later callback instead of having to
indicate the comeback delay when returning from the handler function.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is for testing purposes to allow a station mode associated to be
dropped without sending the AP a Deauthentication frame.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The TCP code path did not handle the postponed connection attempt on TX
status and the following result message from the Enrollee to the
Configurator. Fix this by adding TCP-versions of these operations to
match the way wpa_supplicant implemented this for the Public Action
frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This extends dpp_test functionality to allow DPP Network Introduction
exchanges to use an incorrect value in the Protocol Version attribute.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use a separate ver=<1|2> parameter to DPP_PKEX_ADD instead of
overloading init=1 with version indication. This allows additional
options for forcing v1-only and v2-only in addition to automatic mode
(start with v2 and fall back to v1, if needed).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This extends hostapd with the design used in wpa_supplicant for PKEX
initiator retries and automatic version fallback from v2 to v1 (the
latter is enabled only with CONFIG_DPP3=y).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Report TX status for DPP messages even if the destination address was
broadcast. This is needed to get appropriate trigger for PKEX retries.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use automatic PKEX version negotiation as the initiator by starting with
PKEXv2 and if no response is received, trying again with PKEXv1. For
now, this is enabled only in wpa_supplicant CONFIG_DPP3=y builds.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The rx_freq of Public Action frame was not maintained by the GO and the
GO always sent the response on the operating channel. This causes
provision discovery failure when a P2P Device is sending a PD Request on
a 2.4 GHz social channel and the GO is responding on a 5 GHz operating
channel.
Save the rx_freq and use it for GO to sent the response. This extends
commit c5cc7a59ac ("Report offchannel RX frame frequency to hostapd")
to cover additional frame types.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend the peer queue flush command with following attributes
1. Enable to flush per TID peer queue
2. Enable to configure when to flush the peer/TID queue
Signed-off-by: Madhvapathi Sriram <quic_msriram@quicinc.com>
