The test here wants to connect and then disconnect again, but it's
driven only by the GO side, so the client may end up (with UML
time-travel) not fully connecting, and then it all fails. Wait for the
client to have connected first.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
p2p_go_neg_init() ignored the provided timeout value and used the
default 15 second timeout in discover_peer(). This did not allow the
recently added go_neg_pbc() timeout increase for concurrent cases to be
used fully.
Signed-off-by: Jouni Malinen <j@w1.fi>
Accept any sequence and number of responses as long as the needed
Bonjour and UPnP services are found.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The full scan at the beginning of the chirping step can take over 15
seconds when 6 GHz and S1G channels are included and the timeout here is
not enough to handle that.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Explicitly flush the scan cache in wpa_supplicant and cfg80211 to avoid
test failures here. An additional BSS table entry from a scan based on a
previous test case could result in causing this test case to report
failure since each beacon response could include multiple entries and
the check for the details would fail due to the unexpected data.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Explicitly wait for the STA to complete connection or channel switch
processing before running the second connectivity check.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
It is possible for the parallel connection attempt with an AP and P2P
device discovery with P2P search on social channels to take close to the
15 second timeout and these test cases could fail because of that
instead of a real issue. Increase the timeout to make this less likely
to cause test failures. In addition, add a debug entry to the log on the
r_dev timeout to avoid confusing print from the i_dev thread reporting a
timeout even when the first timeout was on the rdev_
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Similar to other cases before, this may end up trying to
send the frame before the carrier state is ready. Ensure
it's ready before sending the frame.
To do that, rename the sync_carrier() function and make
the ifname argument optional.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to scheduling in UML time-travel, the test may continue
running and find that the failure didn't trigger when really
the frame just didn't make it through to the other side. Add
some time for the necessary processing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes valgrind reports somewhat cleaner when external libraries
have memory leaks that are not straighforward to fix. In addition,
increase the number of functions to include backtraces since the default
was not large enough to cover some cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow the Timeout Interval Type field in the Timeout Interval element to
be overridden with a different value for testing purposes to be able to
bypass the association comeback processing in mac80211. This allows the
wpa_supplicant internal functionality to be tested.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add HS20TermsAndConditions signal to D-Bus API to allow clients to be
notified when the network requires the acceptance of terms and
conditions. The URL of the T&C page is provided as a signal parameter.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
The ps command as shipped by busybox does not support the "command"
column. Change the code to use pgrep instead which will work fine in all
environments.
In addition, raise an exception if PID was not found since the test
would just hang with pid = 0.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Avoid race conditions (especially with UML time travel) between AP
completion of 4-way handshake and traffic test.
Signed-off-by: Jouni Malinen <j@w1.fi>
The test cases that used country code ZA for the actual test on the 5
GHz band ended up failing in some cases due to various race conditions
with the initial AP start on the 5 GHz band using country code US.
Reduce the risk for that type of failures by using the same country code
ZA for both AP starts.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a test that runs the cfg80211/mac80211 kunit tests (they must be
built as modules to run at this point), and checks the results. The test
is skipped if all the modules fail to load.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add tests for new response handling logic:
1. Verify MSCS change response handling in association / action frame.
2. Verify MSCS unsolicited response handling.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
It looks like the first broadcast frame might be missed in some cases,
so increase the timeout here to allow another round of frames to be
attempted.
Signed-off-by: Jouni Malinen <j@w1.fi>
fils_offload_to_driver2 and wpas_config_file_key_mgmt require
CONFIG_FILS=y, but they did not use check_fils_capa().
Signed-off-by: Jouni Malinen <j@w1.fi>
Verifying that the station can successfully associate again
after being deauthenticated or disassociated.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This triggers a kmemleak scan between tests. This allows finding memory
leaks and doing this should attribute the leak to the correct test in
most cases. Note that it does add a sleep after each test, as such it is
most sensible when combined with UML time-travel.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
We need the station to be fully set up on the AP before
running the connectivity check, not just the station to
be set up itself. Just waiting for the events seems to
still be racy so just sleep a little bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Appending to a bytes() object is rather inefficient. As such, avoid
doing so by first creating a list and then joining all buffers together
at the end only.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
It is possible to execute the tests directly inside the a VM without
necessarily running the repository wrapper script to do so. In these
cases, passing the VM flag using an environment variable allows
correctly flagging this fact to the tests.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
The regulatory domain cannot be reset while the AP is still active. Add
the appropriate commands to bring down the AP after the test, which will
also make resetting the regulatory domain work.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
pyrad does an internal call to getaddrinfo with the service "www".
Make sure this service is known by writing an appropriate
/etc/services file.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
pyrad internally uses socket.getaddrinfo. While it is documented that
one can pass an empty string to bind to all interfaces. The underlying
function expects None instead though, breaking the call.
Either way, it does not hurt to set the bind address to 127.0.0.1
explicitly, so do so to avoid issues.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
It seems that the messages from ip may have a trailing space in some
cases, which may break matching in surrounding logic. Strip the output
to remove whitespace and avoid any issues this may cause.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Extend the previously used minimal test case with full validation of the
selected channel and connection since hostapd now has support for the
HT40- case as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
With UML time-travel, it was possible for a GAS frame to end up in the
capture file for the next test case and if that next case used tshark to
count the number of frames (which is done, e.g., in
gas_anqp_address3_assoc), the following test case could have indicated
failure even when everything worked correctly.
Signed-off-by: Jouni Malinen <j@w1.fi>
