Verify that EAP-AKA' client rejects Challenge with an appended AT_KDF
and a modified AT_KDF value during KDF negotiation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Clarify that proto=RSN is used for WPA3 and add the WPA3-Personal name
for SAE and include OWE as a possible key_mgmt value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Clarify that wpa=2 (i.e., RSN) is used for WPA3 and list previously
undocumented wpa_key_mgmt values.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new test config QCA vendor attribute to override the MU EDCA
parameters to default values in the driver for test configuration. This
is used for configuring the testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When OSEN is used in the BSS that is shared both for production data and
OSU uses, the group cipher might be either GTK_NOT_USED (like in Rel 2
OSEN) or CCMP. Modify hs20-osu-client to allow both these group ciphers
to be used when requesting OSEN connection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check that the @1@ macro gets replaced correctly both when in the middle
and when in the end of the URL template.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The last character of the STA MAC address got replaced with 0x00 due to
truncation if the @1@ macro was used at the end of the URL. Fix this
case by allocating larger buffer for the URL.
Fixes: d4e39c51f8 ("HS 2.0: Move Terms and Conditions Server URL generation from AP to AS")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure HE
trigger frame MAC padding duration value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
ifname is checked for interface down event in commit
106fa1e97e ("nl80211: Indicate
interface-down event only for the main netdev"). Do the same for
interface up event to avoid unexpected notifications when the master
interface (e.g., a bridge interface) is set up while then WLAN interface
remains down.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When we start hostapd having Hotspot 2.0 configuration with interface
already added to bridge interface, addition and deletion of new neighbor
to bridge ip neighbor table fails.
This is since 'bss->added_if_into_bridge' is not set which only allows
'drv->rtnl_sk' (nl_sock for NETLINK_ROUTE) allocation needed for bridge
ip neighbor table.
Add a new bit 'already_in_bridge' and set it when interface is already
added to bridge by some external component. Check this bit in addition
to 'bss->added_if_into_bridge' for 'drv->rtnl_sk' allocation done in
i802_init().
Now 'drv->rtnl_sk' is closed in wpa_driver_nl80211_deinit() regardless of
'bss->added_if_into_bridge' since when we have 'bss->already_in_bridge'
case too, this need to be removed.
brctl show
bridge name bridge id STP enabled interfaces
br0 8000.8efdf006b050 no ap
hostapd_cli raw STATUS-DRIVER
Selected interface 'ap'
ifindex=15
ifname=ap
brname=br0
addr=8e:fd:f0:06:b0:50
freq=5180
beacon_set=1
already_in_bridge=1
..
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Since the generic DFS offload support flag is added as
NL80211_EXT_FEATURE_DFS_OFFLOAD, only use the vendor command to check
DFS capablity if the flag is not already set.
Signed-off-by: Peng Xu <pxu@codeaurora.org>
Add a new wifi test config QCA vendor attributes to configure
HE MU EDCA parameters value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure Tx
beamformee number of space-time streams value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends the terms.php implementation of Hotspot 2.0 Terms and
Conditions server to allow it to interact with hostapd(AS) to clear the
filtering rules from the AP. After requesting hostapd to send out the
CoA-Request, terms.php waits for up to 10 seconds to see whether the
current_sessions table gets an update to indicate that filtering has
been successfully disabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new DAC_REQUEST control interface command can now be used to request
hostapd to send out Disconnect-Request and CoA-Request packets for an
existing session.
DAC_REQUEST <disconnect|coa> <MAC Address> [t_c_clear]
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows hostapd DAS to be configured to allow any DAC (with the
matching shared secret) to send Disconnect-Request and CoA-Request
packets.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This can be used to track active sessions, e.g., for the purpose of
issuing RADIUS DAS commands (Disconnect-Request or CoA-Request).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed with the modified hostapd implementation to fix the
ap_hs20_terms_and_conditions* test cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it more convenient to generate the URL in a way that
interoperates between different vendors. The AP is simply copying the
already constructed URL as-is from Access-Accept to WNM-Notification.
This means that the HO AAA can generate the URL in a manner that works
for the associated T&C Server without having to coordinate with each AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows hs20-osu-client to configure wpa_supplicant credential with
a specific EAP method so that roaming consortium OI -based matching can
be used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is easier to understand the hostapd debug log here if each step is
noted there before starting the wpa_supplicant operation. In addition,
it looks safer to process all pending event messages between each step
to avoid running out of any buffer limits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
In the infrastructure BSS case, the AP needs to clear pending SAE state
if a new Commit message is received when already in Committed state.
This allows the non-AP STA to negotiate a new group if it ends up trying
to go through SAE authentication again before the AP side has removed
the previous STA entry.
This fixes an issue where a kernel update changed something in SAE
timing or authentication sequence and started failing the
sae_bignum_failure hwsim test case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This test case verifies that wpa_supplicant is able to perform CSA to a
VHT80 channel when having to move the GO due to an avoid-frequencies
driver event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Prefer channels that support VHT80 (and secondarily, HT40 on the same
band) over other common group channels. If no such channel is found,
prefer any channel that uses the same band so that CSA can be used. This
improves the case where a P2P GO needs to move to another channel and
there is no other reason (e.g., preferred channel from the driver or an
already used channel from a virtual interface sharing the same radio) to
pick a specific channel.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it easier to debug why wpa_supplicant selects particular
HT/VHT parameters for AP/P2P GO mode.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When removing an interface, hostapd_bss_deinit() frees all associated
STAs. If any of the stations is 40MHz intolerant, the cleanup invokes
ht40_intolerant_remove(), that in turn registers a 20->40MHz transition
timer for the last station (ap_ht2040_timeout() function). That timer is
never canceled; once it executes, the interface is gone, most likely
resulting in a segfault when referencing it.
While hostapd_interface_deinit() cancels the transition timer, it does
so before cleaning up STAs. Move the cancellation after STA cleanup to
cancel any timer that was registered during that operation.
Signed-off-by: Martin Willi <martin@strongswan.org>
Handle NL80211_CMD_WIPHY_REG_CHANGE the same way as the
NL80211_CMD_REG_CHANGE event. The wiphy-specific event is generated by
the cfg80211 reg_process_self_managed_hints() function, e.g., when going
through regulatory_set_wiphy_regd_sync_rtnl(). Previously, such events
were ignored completely in hostapd/wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The AKM 00-0F-AC:13 is supposed to use cryptographic algorithms
consistently, but the current IEEE 802.11 standard is not doing so for
the key names: PMKID (uses SHA-1), PMKR0Name/PMKR1Name (uses SHA-256).
The PMKID case was already implemented with SHA-384 and this commit
replaces use of SHA-256 with SHA-384 for PMKR0Name/PMKR1Name derivation
to be consistent in SHA-384. While this is not compliant with the
current IEEE 802.11 standard, this is clearly needed to meet CNSA Suite
requirements. Matching change is being proposed in REVmd to get the IEEE
802.11 standard to meet the use case requirements.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
A new SAE Commit message should not be allowed to drop an existing STA
entry since the sender of that Commit message cannot be authenticated
before receiving the Confirm message. This is important in particular
when PMF is used since this would provide a potential new path for
forcing a connection to be dropped.
Fix this by allowing a new SAE Authentication instance to be started
when the old instance is in Accepted state and the new Commit message
does not use the same peer-scalar value (checked in
sae_parse_commit_scalar()). When PMF is used, the AP will use SA Query
procedure when receiving the (Re)Association Request frame. In theory,
that step could be skipped in case of SAE Authentication since the
non-AP STA is demonstrating knowledge of the password. Anyway, there is
no allowance for that exception in the IEEE 802.11 standard, so at least
for now, leave this using SA Query procedure just like any other PMF
case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wpa_supplicant was hardcoded to use BIP-CMAC-128 in FT protocol if PMF
was enabled. Extend that to allow the other BIP algorithms to be used as
well.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd was hardcoded to use 128-bit IGTK in FT protocol (IGTK
subelement in FTE). Extend that to allow 256-bit IGTK (i.e.,
BIP-CMAC-256 and BIP-GMAC-256) to be used as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of sending out a partially completed frame, abort the
association process if something unexpected happens and remove the STA
entry.
Signed-off-by: Jouni Malinen <j@w1.fi>
The implementation changes in hostapd FT error path handling in the
follow commit would result in ap_ft_ap_oom7 test case failing. This is
triggered partially by PMF protections and SA Query attempts, so it
looks like it is easier to split each failure case into a separate test
case.
Signed-off-by: Jouni Malinen <j@w1.fi>
When support for KCK2 and KEK2 was added, both keys were derived for
FT-FILS cases, but only KCK2 was actually used. Add similar changes to
use KEK2 to protect GTK/IGTK in FTE with using FT-FILS AKMs.
This fixes AES key wrapping to use the correct key. The change is not
backwards compatible.
Fixes: 2f37387812 ("FILS: Add more complete support for FT-FILS use cases")
Signed-off-by: Jouni Malinen <j@w1.fi>
The bss variable in this function might be NULL, so make the FT MDE
addition case conditional on a BSS entry being available.
Fixes: 3dc3afe298 ("FT: Add MDE to assoc request IEs in connect params")
Signed-off-by: Jouni Malinen <j@w1.fi>
When building an RRB message, a failure in wpa_ft_rrb_lin() calls could
have resulted in trying to free an uninitialized pointer. Fix this by
initializing *packet to NULL before going through the initial steps.
Signed-off-by: Jouni Malinen <j@w1.fi>
