The new cred block parameter 'temporary' can be used to indicate that a
cred block is not to be saved to wpa_supplicant configuration file
(e.g., "SET_CRED 0 temporary 1"). This is similar to the concept of
temporary network blocks and allows cred blocks to be managed outside
the wpa_supplicant config file when other parameters are still saved to
the file written by wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
The option of handling upper layer P2P management operations within the
driver/firmware was originally planned to be used with wpa_supplicant,
but this has not really happened and there is no clear sign of this
being needed in the near term either. This functionality has not been
completed and it is certainly not being kept up-to-date or tested. As
such, it is best to remove it for now and if this or something similar
is needed in the future, it can be brought back once a clear need for it
has been demonstrated first.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, the shorter scan interval was already in use for the
connection following the provisioning step, but same optimization can
also be used for the pre-provisioning scan.
Signed-hostap: Jouni Malinen <j@w1.fi>
This driver event was used separately for some Action frames, but all
the driver wrappers converted to this from information that would have
been enough to indicate an EVENT_RX_MGMT event. In addition, the
received event was then converted back to a full IEEE 802.11 management
frame for processing in most cases. This is unnecessary complexity, so
get rid of the extra path and use EVENT_RX_MGMT for Action frames as
well as other management frame subtypes.
Signed-hostap: Jouni Malinen <j@w1.fi>
The earlier changes to buffer EAPOL frames when not associated to avoid
race conditions (especially commit
3ab35a6603 but maybe something even before
that) broke PeerKey 4-way handshake. Fix this by using a separate check
before the race condition workaround to process PeerKey 4-way handshake
EAPOL-Key messages differently.
Signed-hostap: Jouni Malinen <j@w1.fi>
P802.11-REVmc clarifies that the Target BSSID field is always present
hen status code is zero, so match that requirement.
Signed-hostap: Jouni Malinen <j@w1.fi>
This commit adds few more debug prints to log the RSSI information from
the scanned BSSIDs and the current connected BSSID when comparing
neighbor results during WNM Transition Management Request processing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, WPS credential provisioning removed duplicated network
entries only if they had identicical SSID, security parameters, and the
keys. However, it is possible that the AP has changes its keys and
leaving the old entry behind can result in connectibity issues (e.g.,
with 4-way handshake failing due to use of the old PSK). Fix this by
allowing the old network entry to be removed even if the keys
(passphrase, PSK, WEP keys) are different.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to enable various testing parameters and
functionality in build configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the AP is expected to be available, there is no need to wait for
the full five second wait between scans during WPS connection. This
speeds up cases where the first scan misses the AP for some reason.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It may not always be desirable to trigger reassociation or network
change based on scan results from externally to wpa_supplicant trigger
scan operations. Skip network selection and roaming determination if the
received scan result is known to be triggered by something external to
wpa_supplicant. The control interface SCAN command can be used to
request wpa_supplicant to determine the best network.
Signed-hostap: Jouni Malinen <j@w1.fi>
This avoids some unnecessary attempts to request the driver to start a
scan while it is still busy with the scan operation that was started by
an external program.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows users of wpa_supplicant control interface to figure out when
their specific scan command has been started and completed. For example:
CTRL-EVENT-SCAN-STARTED
> scan freq=2412,2417 passive=1 use_id=1
3
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-STARTED id=3
CTRL-EVENT-SCAN-RESULTS id=3
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows external programs to request wpa_supplicant to execute
a passive scan (i.e., do not send any Probe Request frames).
Signed-hostap: Jouni Malinen <j@w1.fi>
This parameter was not really used for anything else apart from a debug
message in the same function that set it. In addition, cfg80211 returns
the set of scanned frequencies even for the full scan, so the code that
was setting this conditionally on frequency list not being there was not
really ever entered either.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new freq=<frequency ranges> parameter to the SCAN command can be
used to request a scan to be performed on the specified set of channels
instead of on all channels. For example, "wpa_cli scan
freq=2400-2500,5180" would scan channels 1-14 and 36. Only the channels
that the driver indicates as enabled and that are within the specified
ranges are included in the request.
Signed-hostap: Jouni Malinen <j@w1.fi>
In addition, update build rules to compile object files in the same
directory as the source code file if CONFIG_CODE_COVERAGE=y is set to
make lcov find the source code files.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use an array of ciphers and a loop instead of copy-pasted copies of the
same printing functionality for each cipher.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds initial parts for supporting the new GCMP-256, CCMP-256,
BIP-GMAC-128, BIP-GMAC-256, and BIP-CMAC-256 cipher suites.
Signed-hostap: Jouni Malinen <j@w1.fi>
In wpa_supplicant_terminate_proc(), while iterating and
terminating interfaces, after an interface is terminated,
we can no longer access its memory as it is no longer valid
and causes a crash.
Fix this by saving the pointer to the next interface before freeing
the current one to avoid accessing an invalid memory location.
Signed-hostap: Moshe Benji <moshe.benji@intel.com>
This just serves to check if there was a scan within
the last 5 seconds, hence it should use monotonic time.
While at it, also use os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This is only used for a debug message, but that message prints
the time since the last attempt, so it should use monotonic
time instead of wall clock.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The MMIC failure code should use monotonic time to check
whether 60 seconds have elapsed or not. For type-safety,
use struct os_reltime for the timestamp variable, and
also convert to using os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Temporarily disabled networks are disabled for a certain
duration, so the code should use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
GO activation can fail if the first client doesn't connect
within a certain time, but this should not be dependent on
wall time -- use monotonic time instead.
While at it, use os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The reinit detection skips reinit when the time since the own
authentication frame TX is less than half a second, so it shouldn't
be affected by wall time and use monotonic time instead.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The EAPOL RX workaround checks that the events are less than 100 ms
apart, so only uses relative times and should use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The bgscan simple and learn algorithms should run regardless
of wall clock time jumps, so make them use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The BSS table, scan timeout, and related functionality should use
monotonic time since they care about relative values (age) only.
Unfortunately, these are all connected, so the patch can't be split
further. Another problem with this is that it changes the driver wrapper
API. Though, it seems only the test driver is using this.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The SA query timeout is just a regular timeout (currently
hard-coded to 1000 TU), so use monotonic time for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
bgscan_learn_get_probe_freq() starts from returning the second entry in
the supp_freqs arrays. Change its logic a bit to make it start from the
first entry.
Signed-hostap: Eliad Peller <eliad@wizery.com>
In case the initial signal level of the associated BSS was above the
given threshold, bgscan_learn module would begin using the
short_interval but never switch to the long_interval as there would be
no signal change event. Make the init code poll for the current signal
level and set scan_interval accordingly. This logic exists in
bgscan_simple but was missing in bgscan_learn.
Signed-hostap: Eyal Shapira <eyal@wizery.com>
Some hw modes (e.g., 11b and 11g) contain the same frequencies,
causing the supp_freqs array to be populated with redundant entries.
Check for the existence of the freq before adding it.
Signed-hostap: Eliad Peller <eliad@wizery.com>
Stopping bgscan on any state other than COMPLETED results
in bgscan reset (stop + start) on every rekeying operation.
Signed-hostap: Eliad Peller <eliad@wizery.com>
Do not assume the driver supports QoS Mapping, but instead, advertise
support for this only if CONFIG_INTERWORKING is defined and driver
indicates support for configuring QoS Map.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 202dec2a94 introduced a never
ending loop for a case where a single wpa_supplicant process is used
with multiple radios. Fix this by advancing the iface pointer properly
to the next interface in the loop until a NULL pointer is hit.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Adds support for VHT by parsing bandwidth and center_freq{1,2}.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Based on priority, remove the connection with least priority whenever
a frequency conflict is detected.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
This field allows adds enough information into the P2P-DEVICE-FOUND
events to figure out if the peer supports Wi-Fi Display.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Allow addition static and shared libraries to be specified from the
eap_proxy_*.mk file for Android build. In addition use $(LOCAL_PATH) as
a prefix for that Android makefile part.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
struct wpa_radio is used as a shared data structure between all struct
wpa_supplicant instances that share the same physical radio.
Signed-hostap: Jouni Malinen <j@w1.fi>
An INTERFACE_DISABLED event received on an interface that is
currently operating a P2P GO means that the group session ended.
In such a case, if the interface was dynamically added remove it, and
if not, remove all the network blocks that are temporary, assuming
that if needed a new session will be started by an external entity.
The use case was triggering rfkill (both SW and HW). This case popped up
as part of a testing cycle, where after a toggle in the rfkill state,
the result was that the interface was not deleted, but on the other hand
the wpa_supplicant did not configure the kernel to re-start the AP
functionality again.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
On scan results event if a concurrent P2P scan was triggered previously,
scan results processing is canceled, p2p_find executed, and a new sta
scan is triggered (pending scan). However, this new sta scan does not
restore the scan_req value of the previous scan (whose scan result has
been canceled).
If we are currently connected to an AP and use ap_scan=2, the new
triggered scan will cause an associtation-without-scan in
wpa_supplicant_scan:
(ap_scan == 2 & scan_req != MANUAL_SCAN_REQ)
=> wpa_supplicant_assoc_try()
causing an association error and a disconnection.
This patch fixes this issue by restoring the previous scan_req value.
Signed-off-by: Loic Poulain <loicx.poulain@intel.com>
This is a mechanism used in Android to extend driver interface in vendor
specific ways. This is included only for the purpose of Android
compatibility. Proper interface commands should be used for any new
functionality.
Signed-hostap: Jouni Malinen <j@w1.fi>
Relative time shouldn't be calculated based on gettimeofday
because that clock can jump (e.g., when the time is adjusted
by the system administrator.)
On systems where that is available, use CLOCK_BOOTTIME (on
fairly recent Linux systems, this clock takes into account
the time spend suspended) or CLOCK_MONOTONIC (on Linux and
some POSIX systems, this clock is just freely running with
no adjustments.)
Reported-by: Holger Schurig <holgerschurig@gmail.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Scan initiated from wps_nfc command context was ketp on
getting rescheduled due to an on-going scheduled scan. So
cancel sched_scan before issuing a reassociation scan.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
The shorter 250 ms wait for the next scan request can be used also for
the case of persistent group re-invocation instead of just formation of
a new group. This speeds up the process and makes this more robust
especially in cases where the GO is using MCC.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The QoS Map Set element was passed in full to the driver instead of just
the payload of the element. This resulted in the updated QoS Map being
rejected. Validate the element id/len and send only the payload to the
driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Only force_freq was used in the wpas_p2p_set_own_freq_preference() call
which allowed the P2P module channel re-selection to ignore the
preference for using a channel we are already using. Fix this by setting
either force_freq or pref_freq as the preference based on which one is
set. This allows p2p_ignore_shared_freq parameter to be used whether to
prefer the shared frequency in this case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to use wpas_p2p_num_unused_channels() here in the
default configuration of p2p_ignore_sahred_freq=0, so re-order the
conditions to skip that operation. This is a bit more efficient and the
debug log is also a bit cleaner in the default case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_ignore_shared_freq=1 was supposed to allow a MCC-capable device to
ignore a preference for using the same channel on multiple interfaces.
However, it was not used when inviting a peer to re-invoke a persistent
group. This case needs special handling since the peer's channel list is
not available to perform channel reselection and the operating channel
indicated in the Invitation Request frames ends up getting used as the
operating channel if the transmitted of that frames becomes the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_ignore_shared_freq=1 was supposed to allow a MCC-capable device to
ignore a preference for using the same channel on multiple interfaces.
However, it was not used during processing of an Invitation Request. Fix
that case to use channel preference instead of channel forcing if free
channels are available. This allows p2p_ignore_shared_freq=1 case to
ignore the preference.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is confusing to talk about current operating channels being
unavailable for P2P when there are no current operating channels. Make
the debug message easier to understand.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is clearer if there is only a single loop of the channel list and
shared debug prints. In addition, the note about current operating
channels not being available is quite confusing if there are no
operating group, so make that part of the message conditional.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 0d08efa447 modified
wpas_p2p_setup_freqs() design to use number of MCC channels capability
from the driver. However, it resulted in regression on how the preferred
vs. forced channel selection is done in the case of a MCC device.
force_freq was set unconditionally even though this was supposed to be
done only if no additional channels are available. pref_freq needs to be
used when possible to avoid preventing connection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
While starting from PNO start context, the scheduled scan was not
setting the flag wpa_s->scanning. This was resulting in the subsequent
SCAN command to proceed further and send command to nl80211/cfg80211.
The expected behavior of cancelling sched_scan was not happening here.
While sched_scan is in progress and a legacy scan comes on the
cli/socket, the sched_scan is cancelled and normal scan is allowed to
continue. However, sometimes sched_scan cancelled event comes a bit
delayed and we will send out the scan command before the wpa_s->scanning
is cleared. Instead, reschedule the incoming scan req if the
wpa_s->scanning shows that it is still in progress.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Add chan_switch to the control interface of wpa_supplicant and hostapd,
and also to wpa_cli and hostapd_cli.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Build CSA settings and call the driver to perform the switch. Construct
Beacon, Probe Response, and (Re)Association Response frames both for CSA
period and for the new channel. These frames are built based on the
current configuration. Add CSA IE in Beacon and Probe Response frames.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add csa_settings struct which holds parameters for CSA. Change driver
interface for switch_channel(), so that it will receive this struct and
not only the new frequency as it was before. This allows wpa_supplicant
to provide all the required parameters (beacons, proberesp, assocresp,
CSA IE) which are required by cfg80211 implementation.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This was supposed to be a minimal sample of eloop wrapper, but it is
unclear whether this is of that much use and the file has not been kept
up-to-date. Remove this file to reduce maintenance effort. The other
eloop*.c files can be used as a starting point if something new is
needed.
Signed-hostap: Jouni Malinen <j@w1.fi>
This triggers re-transmission of CTRL-EVENT-STATE-CHANGE and
CTRL-EVENT-CONNECTED events on STATUS command for Android framework
specific processing.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Commit eb32460029 left an unneeded
sim_type argument to scard_init(). Remove that unnecessary argument to
clean up the implementation.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Add DBus methods for TDLS operations similar to those available
for the control interface. This includes Discover, Setup, and
Teardown commands. While here, add a method to query the TDLS
link status and add a DBus method for it.
Tested with CONFIG_TDLS enabled, on a TDLS-enabled host and
peer capable of TDLS:
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>
yields: string "peer does not exist"
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSDiscover string:<peer-mac-address>
yields no error
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSSetup string:<peer-mac-address>
yields no error
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>
yields: string "connected" after TDLS completes
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSTeardown string:<peer-mac-address>
yields no error
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>
yields: string "peer not connected"
Signed-hostap: Paul Stewart <pstew@chromium.org>
Request new scan only for the interface for which the original scan
request and results has come. Otherwise while sharing scan results along
with P2P interfaces, the new scan will be requested on P2P interfaces.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Since eloop_deplete_timeout() is doing practically same in
wpa_supplicant_req_scan(), revert the old mechanism from commit
7e1488494e to avoid unnecessary work in
this function.
Signed-hostap: Jouni Malinen <j@w1.fi>
During persistent group re-invocation, GO may end up using a different
channel as the operation channel compared to what was indicated in the
invitation frames. This may break the connection if the peer device ends
up scanning the GO only on the channel from the invitation frame. Fix
this by using the negotiated channel (if available) on the GO as the
operating channel instead of the channel that was provided in the
p2p_invite command to start negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There are use cases requesting the host driver to initiate the TDLS
setup with the peer only when configured by the external applications.
Thus, enable this control by tdls_external_control=1 and pass the
requisite information for the specific TDLS operation to the driver
on the request from such use cases.
This operation mode expects the driver to initiate TDLS link
automatically based on signal strength and traffic to a peer and tear
down links whenever they are not used or suitable due to signal strength
etc. The list of peers with which such operations are to be performed
are provided with the TDLS driver operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is a better way of matching P2P groups based on the unique P2P
Device Address (e.g., from P2P Group ID) and SSID pair instead of using
the not necessarily unique P2P Interface Address.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to parse the IE buffer again to find the SSID of the
BSS since that information is already stored in struct wpa_bss.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a BSS is disallowed temporarily with disallow_aps, the network
connection is going to fail. As such, there is not much point in
allowing Interworking network selection to try to connect with such BSS.
As such, do not consider disallowed networks for automatic network
selection and reject requests to connect to them through
INTERWORKING_CONNECT.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Do not add multiple network blocks for the same network from a single
credential. INTERWORKING_CONNECT used to generate a new network block
for each instance regardless of what network blocks have already been
configured. While this allows the connection to go through, it is not
efficient to leave behind potentially large number of network blocks
with the same contents (or worse, changed contents). Address this by
removing an older network block for the same credential before adding a
new one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If we are already connected to the selected AP with a network block
that was created based on the selected credential, do not force a
reconnection or network block update.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This prints out get_shared_radio_freqs() results and related information
from P2P operations to make debug logs more helpful for figuring out
issues related to multi-channel concurrency.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When trying to choose a frequency that can be used for GO instantiation,
properly check if there are free channels that can be used.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
The idx variable was mistakenly set to 0 at the beginning of the
interface iteration. This could result in the operating channel of the
interface calling the function from being removed from the returned
frequency array if other interfaces were operating.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
This option can be used to globally configure bgscan parameters
for all the network blocks.
Note that this configuration will not override a network block
specific bgscan settings, but will only be used in case that
the network block does not have a valid bgscan configuration.
Signed-hostap: Haim Dreyfuss <haim.dreyfuss@intel.com>
Try to read the IMSI values through the eap_proxy layer for Interworking
functionality again if the value was not available at startup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Number of regressions had shown up in wpa_supplicant implementation of
SAE group selection due to different integer array termination (-1 in
hostapd, 0 in wpa_supplicant) being used for SAE groups. The
default_groups list did not seem to use any explicit termination value.
In addition, the sae_group_index was not cleared back to 0 properly
whenever a new SAE session was started.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was possible for the wpa_s->show_group_started and wpa_s->go_params
to be left set when a P2P group was removed before group formation had
completed. In case a separate P2P group interface was not used, this
could rsult in all future scans using the hardcoded DIRECT-* SSID and as
such, not find the network they were trying to find. Fix this by
clearing these P2P parameters on group removal.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It can be useful to see whether the specific P2P SSID was used for scan
based on p2p_in_provisioning or show_group_started when debugging issues
where this case shows up unexpectedly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When removing and re-adding the first wlan# netdev to hostapd
dynamically, the netdev is already present and should not be removed and
re-added to maintain its state as not-added-by-hostapd so that it does
not get removed automatically.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpas_p2p_setup_channels function uses the per interface information
(wpa_s->hw.modes) for setting up the available channel list for P2P
operation, but if a separate P2P interface is used (e.g., p2p0 on
Android), the wpa_s instance for that interface may not get an updated
channel list. This can result in some operations, like "P2P_SET
disallow_freq", using old channel list information (e.g., world roaming
information with passive-scan/no-ibss flags) which was initialized
during the start-up. This could result in P2P functionality using
conflicting or obsolete channel information.
To resolve this issue, update channel list information on regulatory
change events to all of the virtual interfaces sharing the same phy for
which the event is received.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it more convenient to move BSS configuration entries between
struct hostapd_config instances to clean up per-BSS configuration file
design.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows sp_type={home,roaming,unknown} to be used to determine
network type with SIM-based credentials even if the domain name
parameter is not configured explicitly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit ca9bc5b566 added wpas_conf_ap_vht()
as a static function with the caller within CONFIG_IEEE80211N, but the
function outside. This resulted in a compiler warning for wpa_supplicant
AP/P2P builds when CONFIG_IEEE80211N=y was not used. Fix that by using
matching conditional block around the function.
Signed-hostap: Jouni Malinen <j@w1.fi>
Start GO with VHT support if VHT option was requested
and the appropriate channels are available.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Add the option to ask for VHT operation similarly to the way ht40 is
configured - either by adding 'vht' param to the relevant p2p_*
commands or by configuring p2p_go_vht=1 in the configuration file.
This patch only adds the configuration option (e.g., via control
interface). The actual handling of the VHT parameter (asking the driver
to use VHT, etc.) will be done by the following patch.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
In order to support P2P GO with 11ac support, add CONFIG_IEEE80211AC
config option support to the Makefile.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Both of these variables can result in optimized WPS scans, so better
clear these more consistently to avoid unexpected single-channel scans.
Signed-hostap: Jouni Malinen <j@w1.fi>
This was forgotten from the previous commit which allowed some cases to
trigger single-channel scan incorrectly if an optimized WPS scan had not
yet been completed at the time network selection was started.
Signed-hostap: Jouni Malinen <j@w1.fi>
Make sure special optimized scans (like WPS-single-channel or
sched_scan) do not get used during the network selection scan. This
could have been hit in cases where a previous operation has been stopped
in a state where special scan parameters were going to be used.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new p2p_add_cli_chan=1 configuration parameter can be used to
request passive-scan channels to be included in P2P channel lists for
cases where the local end may become the P2P client in a group. This
allows more options for the peer to use channels, e.g., if the local
device is not aware of its current location and has marked most channels
to require passive scanning.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new p2p_no_go_freq frequency range list (comma-separated list of
min-max frequency ranges in MHz) can now be used to configure channels
on which the local device is not allowed to operate as a GO, but on
which that device can be a P2P Client. These channels are left in the
P2P Channel List in GO Negotiation to allow the peer device to select
one of the channels for the cases where the peer becomes the GO. The
local end will remove these channels from consideration if it becomes
the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_s->conf cannot be NULL because wpa_supplicant_init_iface() would not
allow wpa_supplicant_add_iface() to return wpa_s instance in such state.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 2e5ba4b6d1 moved this to a function
and updated one of the os_snprintf() calls to use the len parameter, but
forgot the other one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Trying to access the SIM card details without checking if the eap_proxy
layer has been initialized can results in a crash. Address this by
sending the request for the IMSI through eapol_supp_sm.c which can
verify that eap_proxy has been initialized.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for there to be two pending off-channel TX frames, e.g.,
when two devices initiate GO Negotiation at more or less the same time.
This could result in the TX status report for the first frame clearing
wpa_s->pending_action_tx that included the newer frame that has not yet
been transmitted (i.e., is waiting to be sent out). Avoid losing that
frame by confirming that the TX status payload matches the pending frame
before clearing the pending frame and reporting the TX status callback.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
DISCONNECT followed by ENABLE_NETWORK ended up starting a scan for a new
connection due to wpa_supplicant_enable_one_network() setting
wpa_s->reassociate = 1. This was done regardless of wpa_s->disconnected
being 1 which should imply that wpa_supplicant should not try to connect
before asked explicitly with REASSOCIATE or RECONNECT.
Fix this by making ENABLE_NETWORK setting of reassociate = 1 and
starting of scans for connection conditional on wpa_s->disconnected ==
0. This will make ENABLE_NETWORK trigger a connection only if
wpa_supplicant is already in a state where it would try to connect if
there are any enabled networks.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
To disallow roaming when a scan request's results are read, callers
of the D-Bus Scan() method may add a new "AllowRoam" boolean key
to the scan options dictionary and set that key's value to FALSE.
Signed-hostap: Dan Williams <dcbw@redhat.com>
If a scan is currently running and the scan interval is changed, a
second scan will be started before the current has finished. This will
in turn, if no networks are configured, cause wpa_s->state to be
forced to WPA_INACTIVE before the first scan has finished.
Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
Need to use the pointer to the current ongoing query instead of matching
from the pending list based on the destination address so that we get
the correct query instance when processing the TX status report.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These operations can have conflicting offchannel requirements, so wait
with a new scan trigger until a pending GAS query has been completed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Offchannel operations needed for a GAS query can conflict with ongoing
scan/connection progress, so delay GAS queries if such an operation is
in progress on the current interface or any virtual interface sharing
the same radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It would be possible to issue another GAS query when a previous one is
still in progress and this could result in conflicting offchannel
operations. Prevent that by delaying GAS query initiation until the
previous operation has been completed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it less likely to forget WPS single-channel scan optimization
in effect after having completed the WPS operation or in case WPS
operating gets cancelled.
Signed-hostap: Jouni Malinen <j@w1.fi>
When a GO or P2P Client invites a peer device to join an already
operating group, the Operating Channel in Invitation Request needs to be
forced to the current operating channel of the group.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_printf() does not need '\n' so remove the extra newline. In
addition, drop the priority of this message from MSG_INFO to MSG_DEBUG
since this is in no way exceptional operation.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it easier to debug issues related to selecting GO information
from the latest updated BSS table entry.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use similar mechanism to CONFIG_PCSC=y case to set the IMSI and MNC
length for eap_proxy. This allows automatic 3GPP realm comparison
against the domain list.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new configuration parameter external_sim=<0/1> can now be used to
configure wpa_supplicant to use external SIM/USIM processing (e.g., GSM
authentication for EAP-SIM or UMTS authentication for EAP-AKA). The
requests and responses for such operations are sent over the ctrl_iface
CTRL-REQ-SIM and CTRL-RSP-SIM commands similarly to the existing
password query mechanism.
Changes to the EAP methods to use this new mechanism will be added in
separate commits.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is needed to avoid issues with control interface commands that
could request BSS list during an eapol_test run. wpa_cli tries to update
its internal BSS list and that could trigger eapol_test crashes without
this.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is what the original implementation did years ago, but the move to
using separate control interface backends re-ordered the implementation
to process EAPOL notification first. Use a registered timeout to allow
the ctrl_iface response to be sent out first to get somewhat faster
response time and to avoid pending operations that could result in
ctrl_iface response and unsolicited event messages from getting mixed
up.
Signed-hostap: Jouni Malinen <j@w1.fi>
The eap_param_needed callback was forgotten from eapol_test and this
prevented external EAP request processing through ctrl_iface from being
tested.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_s->global is now dereferenced in number of places and at least one
of them hits in eapol_test cases. Fix issues with this by setting the
global pointer to empty data.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows credentials to be limited from being used to connect to a
network unless the AP advertises a matching roaming consortium OI.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allow GAS operations to be fine-tuned based what happens with GAS
query TX. Failed queries are timed out immediately and acknowledged
queries are given some more time to account for possible TX queue
latencies.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Indicate support for QoS Mapping and configure driver to update the QoS
Map if QoS Map Set elements is received from the AP either in
(Re)Association Response or QoS Map Configure frame.
This commit adds support for receiving the frames with nl80211 drivers,
but the actual QoS Map configuration command is still missing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allow domain_suffix_match to be specified for a cred block and then
get this copied for the network blocks generated from this credential as
part of Interworking network selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Credentials can now be configured with more than one FQDN ('domain'
field in the cred block) to perform Domain Name List matching against
multiple home domains.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new domain_suffix_match (and domain_suffix_match2 for Phase 2
EAP-TLS) can now be used to specify an additional constraint for the
server certificate domain name. If set, one of the dNSName values (or if
no dNSName is present, one of the commonName values) in the certificate
must have a suffix match with the specified value. Suffix match is done
based on full domain name labels, i.e., "example.com" matches
"test.example.com" but not "test-example.com".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add DFS structures/events handlers, CAC handling, and radar detection.
By default, after radar is detected or the channel became unavailable, a
random channel will be chosen.
This patches are based on the original work by Boris Presman and
Victor Goldenshtein. Most of the DFS code is moved to a new dfs.c/dfs.h
files.
Cc: Boris Presman <boris.presman@ti.com>
Cc: Victor Goldenshtein <victorg@ti.com>
Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
wpa_config_write_key_mgmt has a buffer size of 50. This is not enough
to fit the longest case. I used a network with "WPA-PSK WPA-EAP
WPA-NONE" and CONFIG_IEEE80211R=y + CONFIG_IEEE80211W=y to produce
a string longer than 50 chars. Increase the buffer size to 100 to
prevent truncated output.
Truncated output is not the only problem. If the buffer end is
reached when adding certain key mgmt types the function does not
return immediately. This leaves pos > end. When a second os_sprintf
is called the calculation of end - pos yields a large positive
number for buffer size. End result is a write beyond the buffer end.
Fix this by bailing out if buffer end is reached.
Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
Cancel scheduled scan (if any) before attempting to scan for the newly
received configuration/credential in WPS NFC Config token case.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
P2P-GROUP-STARTED event depends on having enough information about the
group available. To avoid incomplete information from being delivered to
upper layers, do not accept scan results without P2P IE (e.g., from a
non-P2P scan) for P2P client association process. This can be of use for
some join-a-group cases where non-P2P scans have generated the BSS entry
for the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
P2P IE may be available from a Beacon frame from a GO even if we have
not yet received a Probe Response frame with P2P IE from that GO. Since
all the needed information for determining the GO's P2P Device Address
and group capabilities are available, use that information instead of
displaying incomplete group information.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes some P2P-join-a-group cases where GO may have been discovered
based on passive scan or non-P2P scan. P2P IEs may have been received
from a Beacon frame in such a case and that information can be used to
create a P2P peer entry, e.g., to allow provision discovery exchange to
be completed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible that a P2P GO has been discovered through a non-P2P scan
that did not return P2P IE in Probe Response frames. To cover those
cases, check also Beacon frame (if received) for P2P IE.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This could happen when non-P2P station interface runs a scan without P2P
IE in the Probe Request frame. P2P GO would reply to that with a Probe
Response that does not include P2P IE. Do not update the IEs in this BSS
entry to avoid such loss of information that may be needed for P2P
operations to determine group information.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a group was removed before the wait for the first client had timed
out and the client had not yet connected, p2p_go_wait_client could have
been left set and with that, scan operations could be unnecessarily
delayed. This fixes some undesired delays from commit
c1c0b35fea.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 41f853235f extends group formation
timeout for the first data connection to complete and resets
p2p_go_group_formation_completed flag due to which p2p_in_provisioning
and p2p_group_formation flags are not cleared when
wpas_group_formation_completed() is called. This can result in both
station scan and p2p_find failures in the case where separate P2P group
interface is not used and the client does not complete 4-way handshake.
Fix this by clearing p2p_group_formation and p2p_in_provisioning when
such a P2P group is deleted.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add Extended Capabilities element to association request only if the AP
included this element in Beacon/Probe Response frames. This is a
workaround to address interoperability issues with some older APs that
do not seem to be able to handle Extended Capabilities element in
(Re)Association Request frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Update the p2p_go_wait_client timestamp in p2p_go_configured() to
address the case where the group is set up without the provisioning
step.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Making this function be used only for external setup case simplifies the
implementation and makes core wpa_supplicant calls in ctrl_iface.c and
events.c consistent.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Linux capabilities cap_net_admin and cap_net_raw can be used to replace
need for running wpa_supplicant as a root process.
Signed-hostap: Jouni Malinen <j@w1.fi>
STATUS-DRIVER command can now be used to fetch driver interface status
information. This is mainly for exporting low-level driver interface
information for debug purposes.
Signed-hostap: Jouni Malinen <j@w1.fi>
no_ctrl_interface parsing was declared within ifdef CONFIG_CTRL_IFACE
block, so the parser function needs to be marked similarly.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to override previously set ctrl_interface value in a
way that clears the variable to NULL instead of empty string. The only
real use case for this is to disable per-interface ctrl_interface from
the additional control file (-I<file>) in case ctrl_interface was set in
the main configuration file. It should be noted that zero-length
ctrl_interface parameter can be used to initiate some control interface
backends, so simpler designs were not available for this.
The format of the new parameter is not exactly cleanest due to
configuration file parsing assumptions. For example:
ctrl_interface=....
no_ctrl_interface=
would end up with ctrl_interface=NULL.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When the BSS table is being updated based on new scan results, a BSS
entry could end up getting added into last_scan_res list multiple times
if the scan results from the driver includes duplicated values. This
should not happen with driver_nl80211.c since it filter outs duplicates,
but in theory, other driver wrappers could indicate such scan results.
Anyway, it is safer to make sure this cannot happen by explicitly
verifying the last_scan_res list before adding an updated BSS entry
there. A duplicated entry in the list could potentially result in freed
memory being used if there is large enough number of BSSes in the scan
results to cause removal of old BSS entries.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there are large number of BSSes in the scan results, BSS table update
could have added a BSS entry to the last_scan_res in a case where that
BSS entry got just deleted. This would happen only if there are more
than bss_max_count (by default 200) BSSes and if at least bss_max_count
of those BSSes are known (match a configured network). In such a case,
wpa_bss_add() could end up allocating a new BSS entry and return a
pointer to that entry even if it was the one that ended up getting freed
to keep the BSS table length within the limit. This could result in
freed memory being used and the process crashing (likely with segfault)
when trying to access information from that BSS entry.
Fix the issue by removing the oldest BSS entry before linking the new
entry to the table. This makes sure the newly added entry will never get
picked up as the one to be deleted immediately.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, GO considered the group to be fully re-invoked after
starting beaconing on successful invitation exchange. This would leave
the group running until idle timeout (which may not be enabled) or
explicit removal if the client fails to connect for any reason. Since
the client is expected to connect immediately after the invitation
exchange that ends with status=0 (i.e., either client initiated the
exchange or it responded with success), extend group formation timeout
to cover that period until the first successfully completed data
connection. This allows the GO to remove the group automatically if the
client devices does not connect within
P2P_MAX_INITIAL_CONN_WAIT_GO_REINVOKE (15) seconds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, GO considered the group to be fully formed at the completed
of WPS provisioning step. This would leave the group running until idle
timeout (which may not be enabled) or explicit removal if the client
fails to connect for any reason. Since the client is expected to connect
immediately after the WPS provisioning step, extend group formation
timeout to cover that period until the first successfully completed data
connection. This allows the GO to remove the group automatically if the
client devices does not connect within P2P_MAX_INITIAL_CONN_WAIT_GO (10)
seconds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Killing the wpa_supplicant process or using TERMINATE ctrl_iface command
resulted in the process existing without cleaning up possibly added
dynamic P2P group interfaces. Clean this up by stopping each P2P group
before stopping eloop.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, wpa_msg_register_cb() was called only from successful
completion of per-interface control interface initialization. This would
leave the callback unregistered in case only the global control
interface is used which would result in not delivering control interface
events on the global interface. Fix this by registering the callback
handler also from successful initialization of the global control
interface.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If wpa_supplicant ctrl_iface clients are misbehaving and refusing to
read replies or event messages from wpa_supplicant, the single socket
used in wpa_supplicant to send messages can reach the maximum send
buffer limit. When that happens, no more responses to any client can be
sent. Work around this by closed and reopening the socket in case such a
failure state is detected. This is obviously not desirable since it
breaks existing connected sockets, but is needed to avoid leaving
wpa_supplicant completely unable to respond to any client. Cleaner fix
for this may require more considerable changes in the ctrl_iface design
to move to connection oriented design to allow each client to be handled
separately and unreachability to be detected more reliably.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Prepare reply buffer first for all cases and then use a single sendto()
call instead of three calls depending on reply type. This allows simpler
error handling for control interface send operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The interval for the PNO scan did not use the configured sched_scan
interval. This commit addresses the same by using the configured value
or the default of 10 seconds if configuration parameter is not used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It was possiblle for the group formation timeout to be left running even
after the P2P Client connected to the group if the WPS provisioning step
was not completed cleanly (e.g., due to WSC_Done not getting received
from the client). There is no need to remove the group in such case due
to the initial group formation timeout, so work around this by removing
that timeout on data connection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There was already a CFG_CHANGED_P2P_OPER_CHANNEL handler function, but
this flag was not set when the p2p_oper_reg_class or p2p_oper_channel
parameters were changed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant crashes if driver configuration for AP mode interface
configuration fails after group negotiation. This is because of a
regression from commit 1075b29571 that
ends up freeing the wpa_s instance from within
wpa_supplicant_create_ap() without the caller knowing.
Fix this by using an eloop timeout to free remove the P2P group so that
wpa_supplicant_create_ap() and especially wpa_supplicant_associate()
callers do not need to know about interface getting possibly removed. In
addition, move the P2P specific code into p2p_supplicant.c where it
really belongs. This allows the already existing group formation timeout
to be used by reducing the timeout to zero.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Avoid potential issues with removing a P2P group on PSK failure directly
from the wpa_supplicant_event() call since the caller (in driver_*.c)
may not be prepared for the interface disappearing at that point in
time.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the GO of a persistent group to change the PSK or
remove a client when per-client PSKs are used and this can happen
without the SSID changing (i.e., the group is still valid, but just not
for a specific client). If the client side of such persistent group ends
up trying to use an invalidated persistent group information, the
connection will fail in 4-way handshake. A new WPS provisioning step is
needed to recover from this.
Detect this type of case based on two 4-way handshake failures when
acting as a P2P client in a persistent group. A new
"P2P-PERSISTENT-PSK-FAIL id=<persistent group id>" event is used to
indicate when this happens. This makes it easier for upper layers to
remove the persistent group information with "REMOVE_NETWORK <persistent
group id>" if desired (e.g., based on user confirmation).
In addition to indicating the error cases for persistent groups, all
this type of PSK failures end up in the client removing the group with
the new reason=PSK_FAILURE information in the P2P-GROUP-REMOVED event.
Signed-hostap: Jouni Malinen <j@w1.fi>
If a client joins a P2P group multiple times, replace the previous
per-client PSK entry instead of adding a new entry each time.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new control interface command P2P_REMOVE_CLIENT <P2P Device
Address|iface=Address> can now be used to remove the specified client
from all groups (ongoing and persistent) in which the local device is a
GO. This will remove any per-client PSK entries and deauthenticate the
device.
Signed-hostap: Jouni Malinen <j@w1.fi>
Record all generated per-client PSKs in the persistent group network
block and configure these for the GO Authenticator whenever re-starting
the persistent group. This completes per-client PSK support for
persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
When using per-device PSKs, select the PSK based on the P2P Device
Address of the connecting client if that client is a P2P Device. This
allows the P2P Interface Address to be changed between P2P group
connections which may happen especially when using persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to implement per-device PSK selection based on the
peer's P2P Device Address instead of P2P Interface Address.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes the P2P Device Address of the Enrollee available with the PSK
records to allow P2P Device Address instead of P2P Interface Address to
be used for finding the correct PSK.
Signed-hostap: Jouni Malinen <j@w1.fi>
"wpa_cli p2p_set per_sta_psk <0/1>" can now be used to disable/enable
use of per-device PSKs in P2P groups. This is disabled by default.
When enabled, a default passphrase is still generated by the GO for
legacy stations, but all P2P and non-P2P devices using WPS will get
a unique PSK.
This gives more protection for the P2P group by preventing clients from
being able to derive the unicast keys used by other clients. This is
also a step towards allowing specific clients to be removed from a group
reliably without having to tear down the full group to do so.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even after listen duration is over, P2P module remained in
P2P_LISTEN_ONLY state, which is blocking station mode scans. Fix this by
stopping P2P listen explicitly to update p2p_state to IDLE when listen
duration expires.
Signed-hostap: Syed Asifful Dayyan <syedd@broadcom.com>
wpa_cli filters out extra DISCONNECTED events from action scripts. This
ended up filtering out the first real DISCONNECT event in case wpa_cli
was started when wpa_supplicant was in connected state. Change wpa_cli
to allow the first disconnection event to be reported to the action
script in such case.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, network added event was skipping during group formation.
However, this did not necessarily catch all cases of temporary P2P
network blocks. Check ssid->p2p_group to make this behavior more
consistent by avoiding all P2P groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
By default, P2P is initialized for all driver interfaces and this makes
P2P getting initialized for non-P2P station interface if the supplicant
is started first on this interface. If an interface is dedicated for
non-P2P station mode, it is now possible to disable P2P initialization
by adding 'p2p_disabled=1' in the configuration file of non-P2P station
interface, irrespective of the order in which supplicant is started.
Signed-hostap: Sreenath Sharma <sreenats@broadcom.com>
Right now in case of deauthentication from GO, immediate group removal will
happen in GC only if the deauthentication packet has a valid IE. However,
the IE in deauthentication packet is mandated only for managed P2P group.
So in normal P2P group the group removal is delayed and will happen later
only in group idle timeout.
This fixes a regression from commit
d7df0fa727 that changed the previous check
for data->deauth_info != NULL to data->deauth_info->ie != NULL.
Signed-hostap: Sreenath Sharma <sreenats@broadcom.com>
It is possible for the peer device not to support Authentication frame
exchange even though this would be required functionality in the
standard. Furthermore, either Authentication frame may be lost. To
recover from cases where Authentication frame sequence 2 is not
received, start EAPOL Authenticator from one second timeout.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, concurrent station mode scans were postponed during an
ongoing P2P group formation up to the point of completed WPS
provisioning step. This would allow a scan to be started before the P2P
client has completed association for the data connection if a scan
request were timed to hit the window between the provisioning step and
the following association. Avoid this by extending P2P-in-progress state
to continue until the first data connection has been completed as part
of group formation. Use a ten second timeout for this to avoid leaving
scans disabled indefinitely if the client fails to connect completely.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the driver to report EAPOL frame RX before
Authentication frame RX even if the frames arrived in the opposite
order. This can result in issues in cases where both IBSS peers initiate
Authentication frame exchange at about the same time and one of the
EAPOL sessions is started before processing Authentication frame seq=1
RX. Work around this by not re-initializing EAPOL state on
Authentication (SEQ=1) RX if own Authentication frame was transmitted
within last 500 ms.
Signed-hostap: Jouni Malinen <j@w1.fi>
This provides status information about the negotiated group to
wpa_supplicant control interface monitors during group formation in a
form that is easier to use than having to fetch the information
separately.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This replaces number of perror() calls with wpa_printf() to get the
error messages embedded within rest of the debug messages in the same
stream instead of pushing these to stderr which may get directed to
another location.
Signed-hostap: Jouni Malinen <j@w1.fi>
This new control interface event message is used to indicate when
both 4-way handshakes have been completed with a new IBSS peer.
Signed-hostap: Jouni Malinen <j@w1.fi>
This provides global status information that is applicable to all
interfaces (e.g., P2P state). In addition, ifname/address pairs are
listed to get information of all the interfaces that are currently
managed through this wpa_supplicant instance.
Signed-hostap: Jouni Malinen <j@w1.fi>
This iterates through all interfaces and saves configuration file
updates for each interface that allows it (update_config=1).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows global parameters to be set through the global control
interface without having to use IFNAME prefix. For now, this covers
only the wifi_display parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
There were some code paths that allowed obsolete configuration data
pointer to be maintained within EAPOL supplicant in case a network was
removed while not connection to it (i.e., wpa_s->current_ssid not
pointing to the network that was removed). This could result in use of
freed memory, e.g., from eap_sm_notify_ctrl_attached() when a new
control interface connected prior to the EAPOL supplicant configuration
pointer got updated.
Signed-hostap: Jouni Malinen <j@w1.fi>
In AP mode the frequency was initialized only after trying to set up the
AP which caused failure. Move AP frequency initialization to the right
place. This allows an AP mode network block without the frequency
parameter to be used with the default channel 11 being selected in that
case.
Signed-hostap: Avraham Stern <avraham.stern@intel.com>
When 'p2p_group_remove *' is called while the station interface
is connected, the flow also disconnects the station interface.
Fix this by skipping non-P2P interfaces in the iteration.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
According to WSC specification (Ver 2.0.2, section 8.3), RF Bands
attribute should be set to the specific RF band used for the current
message. Add an option to set wanted band in wps_build_rf_bands() and
add a callback to get the current band from wpa_supplicant and hostapd.
Signed-hostap: David Spinadel <david.spinadel@intel.com>
Reduce the wait time for the monitor control interfaces to get
messages on wpa_supplicant de-init etc., as this significantly delays
the shutdown of the wpa_supplicant.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
In case a control interface socket is detached because of sendmsg()
failing for the socket, function call to detach the socket uses a
pointer to the socket information in the structure to be freed. Reorder
code to print socket info before freeing the data to avoid use of freed
memory in case debug prints are enabled.
Signed-hostap: Jouni Malinen <j@w1.fi>
This keeps wpa_supplicant from hanging forever if the other end of the
socket dies. This is similar to the earlier commit
4fdc8def88 to make the global control
interface befave in the same way.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, wpa_supplicant behavior in WEP configuration was to try to
mimic a device that is not aware of WPA/WPA2 and as such, it tried to
connect to a WPA/WPA2 AP with the assumption that the AP could be
providing support for both WEP and WPA/WPA2 stations in the same BSS.
Such APs could have been used during transition from WEP to more secure
options, but that type of deployment have not been used in large number
and are not really of much use anymore taken into account that more or
less all new devices support WPA/WPA2. That combined with the preference
to deprecate WEP justifies removing this use case and making WEP
networking matching more strict by using the knowledge of AP advertising
WPA/WPA2 as an indication of WEP not being supported.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit c7a67a7719 forced disconnection
when wpas_clear_wps() is called. Call this function from a registered
timeout when processing a failure event in order to allow the WPS
handshake to be completed with WSC_NACK and EAP-Failure.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This reverts commit ce970851af.
It turned out that this breaks lots of use cases where p2p_find is
issued while already in p2p_listen state. As such, we cannot reject
p2p_find this easily without checking for more specific cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
Though p2p_find is not expected during ongoing P2P connection, it is
possible that any third party application issues a p2p_find resulting in
connection failure. Address this by rejecting any p2p_find command while
connection is in progress.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
cfg80211 does not allow the zero duration of remain-on-channel. Instead,
use 20 ms as default waiting time when remain-on-channel is used to
schedule offchannel transmission that does not expect a response.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
4-way handshake may fail under extremely noisy environment and if this
happens during P2P group formation, the 10 second extra delay added in
wpas_auth_failed() can result in running over the 15 second timeout.
Avoid this by skipping the delay mechanism in wpas_auth_failed() for the
P2P group formation case. The P2P formation timeout will take care of
stopping the attempts if the failure condition does not get resolved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Change the P2P flows to use the number of concurrent channels
supported by the device and the number of currently used channels
for the P2P flows.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
Some driver interfaces may not support the get_radio_name() design and
get_shared_radio_freqs() needs to be aware of such possibility when
determining shared radio frequencies.
Signed-hostap: Jouni Malinen <j@w1.fi>
There are devices that can operate several channels concurrently.
Change shared_vif_oper_freq() to get_shared_radio_freqs() that can
return an array of frequencies currently used by all the virtual
interfaces that share the same radio.
In addition, move it to wpa_supplicant.c, so it can be used by other
modules.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
Previously, drivers only reported if they support multiple concurrent
channels, but did not report the maximum number of supported channels.
Add this reporting to the driver capabilities and add the implementation
to driver_nl80211.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
To better support the IBSS/RSN mechanism, wpa_supplicant has to be able
to detect a possible peer reboot and in this case it should start a new
EAPOL handshake.
To perform such reboot detection wpa_supplicant has to perform an Open
Authentication by sending an Authentication frame and then replying to
it. IF an Authentication frame is received when the key have already
been exchanged, wpa_supplicant understands that the peer has rebooted
and can reset its state machine.
Whenever a new peer is added to the IBSS wpa_supplicant will start the
Open Authentication and only after having accomplished it will start the
key exchange. If the driver does not support Authentication frame
exchange initiated from user space, this step is skipped to maintain
previous behavior (just go through EAPOL-Key frame processing).
The Open Authentication was partly supported by the Linux kernel but now
wpa_supplicant can register for Authentication frames, handle it in
userspace and so avoid any possible race condition.
Signed-hostap: Nicolas Cavallari <cavallar@lri.fr>
Signed-hostap: Antonio Quartulli <antonio@open-mesh.com>
Commit 1aef400bf0 implemented IBSS RSN
disconnect() call using sta_deauth() in a way that resulted in NULL
pointer dereference in driver_nl80211.c if SME was in user space. Fix
this by passing the own MAC address in the sta_deauth call.
Signed-hostap: Jouni Malinen <j@w1.fi>
When the device indicates to take care of TDLS operations the TDLS
setup is done calling wpas_drv_tdls_oper(). This patch does a similar
thing for the teardown. This fixes failure of teardown:
"TDLS: Could not find peer <mac> for link Teardown"
Signed-hostap: Arend van Spriel <arend@broadcom.com>
Because a delayed scheduled scan will access the members of struct
wpa_supplicant which is freed and this can result in a crash,
wpa_supplicant needs to cancel delayed scheduled scan during cleanups.
Signed-hostap: Chengyi Zhao <chengyix.zhao@gmail.com>
This allows wpa_supplicant to associate to an AP that has VHT BSS
membership selector set to indicate VHT support is required for the BSS.
Without the patch it was impossible to connect to, e.g., hostapd-based
AP that has require_vht=1. wpa_supplicant was complaining with:
hardware does not support required rate 63.0 Mbps
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
There is no need to wait for the 15 second group formation timeout
before indicating P2P group formation failure if GO mode cannot be
started successfully for some reason.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like some of the global control interface cases ended up
blocking in sendmsg() when trying to send an event. Since this can block
all wpa_supplicant processing for multiple seconds, this is very
undesirable. Avoid this by requesting sendmsg() to return an error
rather than waiting for the message to be sent.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
3GPP TS 24.232 Annex A.3 allows network operator to advertise only two
digits of MNC even if MNC has three digits. Allow such matches in
network selection. In addition, allow three digit matches of MNC even if
MNC length was assumed to be two to avoid missing networks if MNC length
cannot be determined reliably. Remove the '-' separator from simulated
SIM/USIM cases to allow the new matching rules to work.
Fix the PLMN List information element parsing loop to use the length of
the PLMN List instead of the length of the full 3GPP Cellular Info to
avoid unexpected matches should a new element ever be added by 3GPP.
Finally, add more debug prints from PLMN matching to make the logs
easier to understand.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpas_clear_wps() was just clearing the current wpa_s->current_ssid
pointer when removing a WPS network block which with the device was
associated. This could leave the association up even though the network
block had already been removed. Prevent this by explicitly disconnecting
from the network instead of such clearing current_ssid.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Adding a new wpa_supplicant control interface for the dedicated
P2P_DEVICE would be quite confusing for programs that manage P2P
operations. Remove this control interface and require the global control
interface to be used since it will provide consistent interface for both
the new dedicated P2P_DEVICE (non-netdev) and old style P2P management
through a netdev.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit c68f6200a7 made these calls
conditional on !p2p_mgmt, but forced p2p_mgmt=1 for cases where the
driver does not use the dedicated P2P Device. Fix this by making the
!p2p_mgmt condition apply only if the driver does indicate use of a
dedicated P2P Device.
Signed-hostap: Jouni Malinen <j@w1.fi>
The interface name for the P2P group interface is derived from the
P2P management interface. When the P2P management interface is a
P2P Device interface, i.e., p2p-dev-wlanX, the name for the group
interface is abbreviated to p2p-X (X being group index). When the
P2P management interface starts with p2p-dev- use its postfix
instead. So P2P management interface p2p-dev-wlan3 results in group
interface name p2p-wlan3-0.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
If the capability flag of the driver indicates a dedicated P2P Device is
supported, a P2P Device interface is created.
Create the P2P Device in main interface creation loop when the added
interface flags support and P2P supplicant is not yet initialized
avoiding recursion of add_interface.
Do not register l2_packet for P2P Device interface (both for EAPOL and
for TDLS).
Signed-hostap: Arend van Spriel <arend@broadcom.com>
Setting p2p_no_group_iface means 'use P2P management interface as P2P
connection interface' because it attempts to change the interface type.
The P2P_DEVICE is a dedicated interface and can not be changed. As such
ignore the configuration option.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
When using OpenSSL with TLS-based EAP methods, wpa_supplicant can now be
configured to use OCSP stapling (TLS certificate status request) with
ocsp=1 network block parameter. ocsp=2 can be used to require valid OCSP
response before connection is allowed to continue.
hostapd as EAP server can be configured to return cached OCSP response
using the new ocsp_stapling_response parameter and an external mechanism
for updating the response data (e.g., "openssl ocsp ..." command).
This allows wpa_supplicant to verify that the server certificate has not
been revoked as part of the EAP-TLS/PEAP/TTLS/FAST handshake before
actual data connection has been established (i.e., when a CRL could not
be fetched even if a distribution point were specified).
Signed-hostap: Jouni Malinen <j@w1.fi>
In wpa_supplicant_deinit(), the function wpas_p2p_deinit_global()
was called. Remove it as it will be called from wpas_deinit_iface()
upon removal of the P2P management interface.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
Add "StaAuthorized" and "StaDeauthorized" D-Bus interface in AP mode.
After enabling the AP mode of wpa_supplicant, the other process need to
get the MAC address and authorization status of every station, so
wpa_supplicant emits signal when the station is authorized or
deauthorized.
Signed-hostap: Chengyi Zhao <chengyix.zhao@gmail.com>
Add AVG_RSSI report to the signal_poll command if it is reported by
the kernel.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
11b rates removal have had impact on SoftAP functionality in
wpa_supplicant. This patch verifies that only in case of P2P group
operation 11b rates will be eliminated. Refer also to commit
4c2c302893.
Signed-hostap: Alexander Bondar <alexander.bondar@intel.com>
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
There is not much use for enabling WPA without WPA2 nowadays since most
networks have been upgraded to WPA2. Furthermore, the code size savings
from disabling just WPA2 are pretty small, so there is not much
justification for maintaining this build option. Remove it to get rid of
undesired complexity.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver wrapper supports best operation channel indication, the
p2p_group_add command can now use special values (freq=2 and freq=5) to
indicate that the re-invoked persistent GO is to be started on the
specified band.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to get wpa_supplicant into clean state during testing if
a test case triggers countermeasures.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Enable tab completion for the cases where ifname= prefix is used in
interactive mode by skipping over that prefix before running through the
per-command completion routines. The ifname= prefix itself is also
covered by adding the possible interface names to the command list.
Signed-hostap: Jouni Malinen <j@w1.fi>
Strip out the IFNAME=<ifname> prefix from commands before parsing them
through the normal processing and then add the prefix back to the
beginning of the actual control interface command to make per-interface
commands work through the global control interface without having to use
the 'raw' command.
Signed-hostap: Jouni Malinen <j@w1.fi>
Define a proper event prefix and include additional information to allow
ESS Dissassociation Imminent event to be used in a wpa_cli action
script.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes ENABLE_NETWORK behave similarily to SELECT_NETWORK by
allowing a scan to be skipped if recent scan results are available.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_s->pending_bssid is all zeros during connection attempt when
driver-based BSS selection is used. Take this into account when
determining whether new scan results should trigger a connection based
on wpa_s->current_ssid, i.e., a connection attempt with the selected
network instead of selected BSS.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When STA interface is connected and P2P interface gets invited in a
different channel from previous P2P group, the invitiation would fail
because of no common channel found. Fix this by using different logic
when device support multi channel concurrency.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The five second timeout for GAS queries is excessive and can result in
long waits in cases where APs are either misconfigured or frames are
lost.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the design more robust against unexpected duplicates since
each new GAS exchange gets a different dialog token compared to the
previous one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like it may be possible for an older GAS response to get retransmitted
even after the first copy has been processed. While this should not really come
up all the way to wpa_supplicant due to sequence number being same (i.e.,
duplicate detection should from the frame), some cases have been observed where
this did cause issues. Drop such a frame silently without dropping the ongoing
GAS session to allow a frame with the next frag_id to be processed after this.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This can be useful for some test cases, so allow wpa_supplicant to be
built with special test functionality to expose the current (last
configured) GTK. This is disabled by default and can be enabled by
adding following line into .config:
CFLAGS += -DCONFIG_TESTING_GET_GTK
The GTK can then be fetched with "wpa_cli get gtk".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The P2P management operations like P2P_FIND and P2P_CONNECT are not
really specific to any network interface. These are P2P Device level
operations that are in more global device context. Allow those to be
sent through the global control interface without IFNAME parameter.
For now, these commands are directed within wpa_supplicant to the
network interface that initialized the global P2P context. This may
change in the future if a special context is added for P2P operations.
Anyway, such changes can now be done internally within wpa_supplicant
without affecting this global control interface design from external
view point.
Signed-hostap: Jouni Malinen <j@w1.fi>
These events are sent as a special case to both the group interface and
"parent interface" (i.e., the interface that was used for managing P2P
negotiation). The latter is not really correct event, so get rid of it
with the new global control interface design where there is no need to
support legacy upper layer implementations.
Signed-hostap: Jouni Malinen <j@w1.fi>
This removes the "IFNAME=<ifname> " prefix from P2P events that are
received through the global control interface since these events are not
really specific to any network interface, but the full device.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace direct wpa_msg() calls with p2p_dbg(), p2p_info(), and p2p_err()
calls that use a new debug_print() callback to handle actual debug
printing outside the P2P module.
Signed-hostap: Jouni Malinen <j@w1.fi>
This removes wpa_ctrl.h dependency from src/p2p/* and makes the P2P
events more consistent, i.e., everything that is aimed for upper layer
processing from the wpa_supplicant control interfaces is generated in
p2p_supplicant.c.
Signed-hostap: Jouni Malinen <j@w1.fi>
This function can be used instead of wpa_msg() and wpa_msg_ctrl() to
indicate that an event is not specific to a network interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
The ATTACH/DETACH mechanism to request event messages from
wpa_supplicant can now be used through the global control interface,
too. This results in events from all interfaces being delivered through
a single monitor socket. "IFNAME=<ifname> " prefix is used on events
that are specific to an interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to implement filtering of channels for scan and based
on that, for connection, purposes.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This updates hostapd to build using the new keystore header file
location and adds a note that the old frameworks/base/cmds/keystore can
be removed at some point in the future when old Android releases do not
need to be supported.
Signed-hostap: Jouni Malinen <j@w1.fi>
The wpa_supplicant global control interface parameter can now be used to
explicitly specify an abstract UNIX domain socket (Linux specific
extension) with "@abstract:" prefix and an Android control socket with
"@android:" prefix.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is mostly a corner case at this point, but if wpa_cli was started
with global control interface connection (-g) and interactive mode,
per-interface control interface was tried to be opened with the
previously opened global ctrl_iface connection gettign leaked.
Signed-hostap: Jouni Malinen <j@w1.fi>
The optional -G<group> command line argument can be used to specify the
group that can access the global control interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
"IFNAME=<ifname> " prefix can now be used on the wpa_supplicant global
control interface to direct a command to a specific interface instead of
having to use an interface specific control interface for this. This
allows a single socket to be used for controlling multiple virtual
interfaces.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 21d996f775 added p2p_pref_chan as a
configuration file parameter, but included only the case of dynamically
setting this at runtime through the control interface SET command.
Complete this functionality by taking this value into use directly from
the configuration file, too.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
By default, dbus_connection_dispatch() will call _exit() if the bus
connection has been closed. This caused wpa_supplicant to terminate
without properly cleaning up after itself.
To ensure that we terminate cleanly when the messagebus terminates,
override the exit_on_disconnect behavior and install a filter to handle
libdbus's "Disconnected" signal.
[Bug 474]
Signed-hostap: Daniel Gnoutcheff <daniel@gnoutcheff.name>
The new control interface command can be used to send a
BSS Transition Management Query frame to the current AP.
Signed-hostap: Vinayak Kamath <vkamat@codeaurora.org>
The WPS provisioning case does not result in successful connection by
design and as such, this can result in networks getting temporarily
disabled. Avoid this by clearing the failure counts on WPS success.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of just adding the new network, prefer the network learnt from a
configuration token during the first connection attempt. This makes the
WPS NFC case behave similarly to the in-band provisioning cases if there
are more preferred networks in the scan results.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up debug log by not trying to process the disconnection
event as a failure that could result in blacklist addition and auto
connect attempt. These are pointless operations since the interface is
going to removed immediately after this.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up debug log by not requesting the auto connect on
dissassociation event if we are already in disconnected state and would
not try to connect anyway.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no point in marking a BSS temporarily blacklisted based on a
connection failure or disconnection case if that happens as a result of
a local request to disconnect. The blacklist entry could result on
unexpected BSS getting selected on the next connection attempt. In
addition, the code to try to find another BSS within the ESS could
result in scanning a single channel on the next attempt. Fix these
issues by handling the connection failure events only if we are not in
disconnected state (i.e., would try to reconnect after this
automatically).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Scanning can delay concurrent operations considerably, so it is better
to avoid that while trying to connect on any of the virtual interfaces
that share the same radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a VIF is already associated, then only scan on the associated
frequency if user requests such. This is a big help when using
lots of virtual stations.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
In the systemd interface templated the alias entry was specified
with wlan0 hard coded. Changing it to %i in this patch. [Bug 477]
Reported-by: zg <ml@mail.tsaitgaist.info>
Signed-hostap: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
cfg80211 rejects the set_key operations before the IBSS network has been
fully formed, so add one more attempt to set the key for WPA-None at
IBSS joined driver event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to repeat the driver capability fetch for each
operation since we already cache driver flags in wpa_s->drv_flags.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new sched_scan_interval parameter can be used to set the default
sched_scan interval, e.g., for power saving purposes.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The use of AID=1 for the nl80211 dummy STA case is specific to the
driver (cfg80211), so better move this into the driver wrapper instead
of generic TDLS implementation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's AID is required for the driver to
construct partial AID in VHT PPDU's. Pass this information to the driver
during add/set station operations (well, as soon as the information is
available, i.e., with set station operation currently).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The Hotspot 2.0 specification seems to mandate this element to be
included in all (Re)Association Request frames if the station is Hotspot
2.0 capable. However, that results in conflicts with other requirements
like no TKIP use when this element is present. The design is really
supposed to include the indication element only for Hotspot 2.0
associations regardless of what the current specification implies.
Remove the HS 2.0 Indication element from (Re)Association Request frame
whenever the connection is not for Hotspot 2.0 purposes.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes tab completion work better in cases where wpa_cli is started
after wpa_supplicant has already discovered BSSes.
Signed-hostap: Jouni Malinen <j@w1.fi>
The old help text did not include most of the parameters and as such,
was not really helpful. Replace it with tab completion function that
includes more or less all available parameters.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, interactive mode could not be used to enter space-separated
lists with the set command. This removes that restriction and allows
such commands to be encoded properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows one to limit the channels that wpa_supplicant will
scan. This is a useful addition to the freq_list configurable
in the network {} section.
Signed-hostap: Ben Greear <greearb@candelatech.com>
This updates number of comments in android.config to match the latest
version in defconfig and adds some of the entries that were previously
present only in android.config into defconfig.
Signed-hostap: Jouni Malinen <j@w1.fi>
Each attempt to connect to the same network using WPS would result
in the duplicate configuration getting added. Avoid such redundant
additions by comparing the network configuration with an already
existing one and remove the older network if the new credential
provisioned through WPS is identical.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
nl80211 has obsoleted WEXT as the preferred kernel interface for
controlling wireless drivers. Update wpa_supplicant driver interface
list order so that nl80211 gets used first if both nl80211 and wext
interfaces are included in the build. In addition, update README to
reflect the fact that WEXT is obsolete.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There are quite a few places in the current implementation where a nul
terminated string is generated from binary data. Add a helper function
to simplify the code a bit.
Signed-hostap: Jouni Malinen <j@w1.fi>
The nfcpy script used to be run in a way that left them running for
multiple operations. This is not desired for some use cases, so provide
options to request only a single operation to be performed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
NFC connection handover messages may be longer than 100 octets, so
increase wpa_cli buffer size to allow longer messages to be reported.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reset ft_completed if STA receives deauthentication
between FT reassoc success and the subsequent initial
mobility authentication and association.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only explicit indications of authentication failures were
used to disable a network block temporarily. Extend this to use multiple
failed connection attempts as a sign of a possible authentication or
authorization failure to reduce the frequency of connection attempts
with a network that does not seem to allow connection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The fast-connect optimization to skip a new scan did not update how the
RSN preauthentication callback is used. There is no point in trying to
add preauthentication candidates from cases where scan was skipped, so
skip this call, too, in such cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
All wpa_supplicant_deinit_iface() callers ended up freeing wpa_s
immediately after this call. Move os_free(wpa_s) into the deinit
function to share the same call and make the deinit sequence clearer.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add "EAPLogoff" and "EAPLogon" interface DBus commands which
parallel the "logoff" and "logon" wpa_ctrl commands which terminate
and restart EAP authentication. Slightly enhance the "logon" case
by expiring any running "startWhile" timer.
Signed-hostap: Paul Stewart <pstew@chromium.org>
This option can be used only for global parameters that are not going
to be changed from settings.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Iliyan Malchev <malchev@google.com>
Add "get_capability freq" command to print a more verbose list of
channels and frequencies in MHz. The tag "NO_IBSS" is added, if IBSS
mode is not allowed on a channel. This allows userspace programs to get
the frequencies and limitations associated with each channel.
This extends the information already provided in "get_capability
channels" but a new interface is chosen because of backwards
compatibility considerations.
Signed-hostap: Bruno Randolf <br1@einfach.org>
Harmonize EAP status events over control interface to provide same
functionality as existing D-Bus callback.
Signed-hostap: Chris Hessing <chris.hessing@cloudpath.net>
"WPS_NFC_CONFIG_TOKEN <WPS/NDEF> <network id>" can now be used to build
an NFC configuration token from a locally configured network.
Signed-hostap: Jouni Malinen <j@w1.fi>
This extends the WPS ER commands that previously accepted only UUID as
an identifier for an AP to use either UUID or BSSID for this.
Signed-hostap: Jouni Malinen <j@w1.fi>
There may be cases where multiple BSS entries for a single BSSID are in
the table. This is mostly in automated test cases due to the AP
configuration changes, but something similar could potentially happen as
a corner case in more realistic networks, too, e.g., when an AP changes
its operating channel. Make network selection more robust by trying to
find the exact BSS entry instead of any BSS entry with a matching BSSID
when storing GAS/ANQP response.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some extended capabilities (I'm currently interested in "Operating Mode
Notification" for VHT) are implemented by the kernel driver and exported
in nl80211. Use these in hostapd/wpa_supplicant.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This is mainly for testing purposes where it is convenient to have an
easy way of getting wpa_supplicant state cleared between test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
If WPS provisioning step is completed with an AP that is in WPS
configured state, we can skip a second scan after the provisioning step
since the AP is unlikely to change its configuration in such a case.
This can speed up WPS connection a bit by removing an unneeded scan.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
This can be used to configure wpa_supplicant to ignore old scan results
from the driver cache in cases where such results were not updated after
the scan trigger from wpa_supplicant. This can be useful in some cases
where the driver may cache information for a significant time and the AP
configuration is changing. Many such cases are for testing scripts, but
this could potentially be useful for some WPS use cases, too.
Signed-hostap: Jouni Malinen <j@w1.fi>
The after_wps counter could have potentially be left in its old non-zero
value in some WPS sequences which could result in a single-channel scan
being used based on obsolete information. Clear after_wps in
wpas_wps_reassoc() to make sure this does not happen.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the AP (P2P GO) has changes its channel of SSID recently, the BSS
table may have multiple entries for a BSSID. Select the one which was
most recently updated for WPS/P2P operations in such case to increase
the likelihood of using current information.
Signed-hostap: Jouni Malinen <j@w1.fi>
Select the BSS entry based on BSSID,SSID pairs instead of just BSSID to
avoid selecting an unexpected SSID for the ROAM command.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit b277a2bebc added a new global
configuration parameter, but forgot to update configuration file saving
to store this.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This new parameter allows wpa_supplicant AP mode operations to use
similar design to the vendor_elements parameter in hostapd to add
vendor_elements into Beacon/Probe Response IE parameters.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
sta_scan_pending was supposed to be accurate enough for determining
whether a P2P scan needs to be postponed. However, it has turned out
that there were cases where sta_scan_pending was not cleared properly.
While the known cases have now been addressed, it is possible that some
other cases may still exist. To avoid issues with P2P operationg getting
stuck, verify more carefully that there is a real pending station mode
scan (either in progress or scheduled to be requested).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Scan result events are shared between all virtual interfaces sharing the
same radio. However, some of the steps are not really appropriate on
virtual interfaces that did not issue the scan request. Fix this by
making these steps conditional on the scan results being processed on
the interface that requested them.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There were couple of code paths that could end up stopping station mode
scanning without clearing sta_scan_pending. This could result in P2P
search getting stuck waiting for completion of station mode scan which
would never show up. Fix this by calling wpas_p2p_continue_after_scan()
in cases where station mode scans are stopped. This allows
sta_scan_pending to be cleared and P2P search operation continued.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make the implementation more consistent and cleaner by using a single
function for addressing all the cases where completion of a station mode
scan operation allows a P2P operation (search) to be re-started.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Replace CONFIG_IEEE80211V with CONFIG_WNM to get more consistent build
options for WNM-Sleep Mode operations. This is similar to the Makefile
change in commit ad3872a372.
Signed-hostap: Jouni Malinen <j@w1.fi>
This code was within ifdef CONFIG_AP and did not get included unless
AP mode support was also enabled. This is similar to the Makefile
change in commit 2dfb9a447c.
Signed-hostap: Jouni Malinen <j@w1.fi>
This fixes the lookup of a usable PMKSA entry in the cache. Using
wpa_s->current_ssid often returns nothing when a usable PMKSA exists in
the cache since wpa_s->current_ssid does not necessarily point to the
correct network entry at this point in time (prior to association).
Signed-hostap: Partha Narasimhan <parthan@gmail.com>
Add a driver capability flag for drivers which support IBSS mode and set
it for nl80211 drivers which have set the NL80211_IFTYPE_ADHOC.
Add a new option "modes" to "get_capability" which will return "AP" and
"IBSS" if the corresponding capability flags are set.
The idea is that this can be used for UIs to find out if the driver
supports IBSS mode.
Signed-hostap: Bruno Randolf <br1@einfach.org>
If a peer replies to persistent group invitation with status code 8
(unknown group), remove the peer from the p2p_client_list if we are the
GO or remove the persistent group if we are the P2P client since it
looks like that the peer has dropped persistent group credentials and
the provisioning step needs to be executed again.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_ignore_shared_freq=1 in the configuration file (or "SET
p2p_ignore_shared_freq 1" on control interface) can now be used to
configure wpa_supplicant to ignore the preference on shared operating
channel when the driver support multi-channel concurrency. The default
behavior is to try to start any new P2P group on an operating channel
that is already in use on another virtual interface to avoid extra cost
from hopping between multiple channels. If this new parameter is set to
1, such preference is not used and instead, the channel for the new P2P
group is selected based on other preferences while ignoring operating
channels of any concurrent connection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 50285f5ca8 changed number of rules
in channel selection and among other things, it broke the design where
the currently used operating channel on a virtual interface that is
shared by the same radio is preferred to avoid costs related to
multi-channel concurrency. Fix this regression by making the P2P module
aware of the shared channel and using that preference as the highest
priority when re-selecting the channel during negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 79879f4ae8 enabled all channels to
be used when negotiating channel with a driver that supports
multi-channel concurrency. Extend that to cover cases where the channel
is not being negotiated (e.g., p2p_group_add to start a GO).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 6a1ce39599 moved the bssid
variable declaration to be outside CONFIG_IEEE80211R block and
triggered a compiler warning about unused variable.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add NL80211_CMD_UPDATE_FT_IES to support update of FT IEs to the
WLAN driver. Add NL80211_CMD_FT_EVENT to send FT event from the
WLAN driver. This will carry the target AP's MAC address along
with the relevant Information Elements. This event is used to
report received FT IEs (MDIE, FTIE, RSN IE, TIE, RICIE).
Signed-off-by: Deepthi Gowri <deepthi@codeaurora.org>
Commit 77dfafd07d cancels group formation
timeout on group removal case but failed to reset the
p2p_in_provisioning flag. This can lead to repeated p2p_find failures if
the group gets removed before completion of the WPS provisioning step
(e.g., GO tears down the group). Fix this by clearing
p2p_pin_provisioning when cancelling group formation.
Signed-hostap: Vivek Natarajan <nataraja@qca.qualcomm.com>
The unprotected disconnection events were previously processed only for
drivers that used the wpa_supplicant SME implementation (separate
authentication and association commands). However, this can be useful
for drivers that use the connect API, so remove the limitation and allow
the same IEEE 802.11w SA Query mechanism to be used even without full
use of the wpa_supplicant SME.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
CONFIG_HT_OVERRIDES and CONFIG_VHT_OVERRIDES were already mentioned in
android.config, but Android.mk did not yet know about them.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add support for VHT capability overrides to allow testing connections
with a subset of the VHT capabilities that are actually supported by
the device. The only thing that isn't currently supported (by mac80211
and this code) is the RX/TX highest rate field.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Instead of using atoi(), use strtol() which allows checking if
the configuration values are valid integers and can understand
more than just decimal (also hexadecimal and octal). This not
only allows specifying some fields in hex (which can be useful)
but also rejecting invalid configurations, e.g.,
disassoc_low_ack=27 * 2
which was previously read as just 27.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Stop sched scan, if running, after any disabling or removing of
a network, and request a new scan if needed.
Signed-hostap: David Spinadel <david.spinadel@intel.com>
Move enabling a network to a separate function. Try to reconnect if not
associated to an AP. Abort scheduled scan in any case of a new scan.
Signed-hostap: David Spinadel <david.spinadel@intel.com>
If the whole ssid list was scanned, don't save the prev scheduled ssid
since we are going to start from beginning. Thos avoids starting sched
scan from prev_sched_ssid after scanning the full list, in case of
adding a network to ssid during scheduled scan.
Signed-hostap: David Spinadel <david.spinadel@intel.com>
In case that the ssid list is longer than max number of ssids,
ths scheduled scan aborted after timeout and rescheduled again
with shorter timeout and longer interval. In case that the timeout
is shorter than the interval, only one scan iteration will
be run. In this case, go back to the initial values.
Signed-hostap: David Spinadel <david.spinadel@intel.com>
When p2p_invite persistent=<id> is used to request a persistent group to
be re-invoked, the peer may reply with status=1 (info not yet available)
if upper layer processing of the invitiation is requested. The peer is
ten expected to start another invitation exchanged within 120 seconds if
the user authorizes the connection. Allow this process to be used more
easily by automatically authorizing the peer that we tried to invite to
use this second invitation sequence even if persistent_reconnect=0.
For this mechanism to work, the device that starts the invitation needs
to start listen mode to be able to receive the invitation request from
the peer. At least for now, this is not done automatically, but future
changes could potentially enable this automatically at least if there
are no concurrent operations in progress.
Example sequence on the initiator:
cmd: P2P_INVITE persistent=1 peer=<addr>
event: P2P-INVITATION-RESULT status=1
cmd: P2P_LISTEN 120
wait for peer to start another invitiation round.. group will be
re-invoked automatically
On the peer (with persistent_reconnect=0):
event: P2P-INVITATION-RECEIVED sa=<addr> persistent=1 [freq=<MHz>]
wait for user approval
cmd: P2P_INVITE persistent=1 peer=<addr>
group will be re-invoked automatically
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When a device that is a GO in a persistent group receives an Invitation
Request from a P2P client and persistent_reconnect=0, upper layer is
notified of this with P2P-INVITATION-RECEIVED event. The upper layer is
supposed to run another invitation exchange is this case, but if that
does not happen and the GO is started without successful (status=0)
invitation exchange, the operating channel for the group may end up
getting set in a way that the P2P client is not able to support. Provide
optional freq parameter in the P2P-INVITATION-RECEIVED event on the GO
side. If this parameter is received and the upper layer decides to issue
P2P_GROUP_ADD command, that command should include this freq parameter
to make sure the operating channel gets selected from the set that the
peer can support.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
beacon_int (in TU) can now be used to configure Beacon interval for AP
mode operations (including P2P GO) in wpa_supplicant. This can be set
either in a network block or as a global parameter in the configuration
file (or with "SET beacon_int <value>" control interface command) to
apply for all networks that do not include the beacon_int parameter to
override the default.
In addition, this commits extends the dtim_period parameter to be
available as a global parameter to set the default value. dtim_period is
now stored in the configuration file, too, if it was set.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Peer device includes its list of allowed operating channels in the
Invitation Response frame. When we are becoming the GO, use that list
from the peer to filter out acceptable channels to avoid selecting a
channel that the peer is unable to use.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When re-invoking a persistent group in P2P client role, the new
pref=<MHz> parameter can now be used with the p2p_invite command to
indicate a preferred operating frequency. Unlike the older freq=<MHz>
parameter, this leaves GO an option to select another channel (from our
supported channels) if the GO cannot accept the channel.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_connect() and p2p_invite() cases used more or less identical
implementatin. Use a shared function to avoid duplicated code.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If multi channel concurrency is supported, we have to populate the
p2p_channels with list of channels that we support. Use the same design
that was previously added for GO Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Most of the print_bss_info() cases were already returning zero lenth to
avoid returning partial returns to the BSS commands, but the HS 2.0 and
Wi-Fi Display entries behaved differently. Make those consistent with
rest of the items.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows ctrl_iface users to iterate through the BSS entries by
fetching multiple BSS entries with "BSS RANGE=N-" without having to use
one extra round to get empty return value as the indication of the last
entry having been found.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This flag will add ==== delimiter between to separate bss results.
Unlike the other BSS command MASK values, this delimiter is not
included by default to avoid issues with existing users of the BSS
command.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This patch uses existing scan results for fast connection on REASSOCIATE
and RECONNECT commands.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
wpa_supplicant uses 4096 byte buffer for control interface responses, so
wpa_cli should do the same to avoid truncating responses unnecessarily.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's VHT capability is required for the
driver to establish a TDLS link in VHT mode with a compatible peer.
Pass this information to the driver when the peer station is
getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can now generate the WPS carrier record for connection
handover response when acting as an ER. The AP whose configuration is
provided in this way is identified with an UUID as an argument to
wps-nfc.py.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the credential to use for a connection with a specific BSS
was picked arbitrary based on first found match of each matching
mechanism. While the credential priorities were used elsewhere, this did
not take into account that different mechanisms could find multiple
matching credentials. As such, the highest priority credential was not
always used in case more than one credential matched with the selected
BSS. Fix this by checking credential priorities again during connection
request.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit bbf41865c9 added calls to functions
that are only defined if CONFIG_WPS_NFC=y. Protect those calls properly
to avoid build issues.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When wpa_supplicant is controlling an AP mode interface, it can generate
the alternative carrier record for NFC connection handover select
message similarly to the way this is done in hostapd.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The last couple of changes to the control interface commands for NFC
connection handover had not yet been documented.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When wpa_supplicant is controlling an AP mode interface, it can generate
the NFC configuration token similarly to the way this is done in
hostapd.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds write-password option for the nfcpy example script for
wpa_supplicant to match hostapd wps-ap-nfc.py functionality.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"WPS_NFC_TOKEN <WPS/NDEF>" used to generate a new NFC password token
regardless of whether there was a pre-configured token in the
configuration. Change this to use the pre-configured value, if
available, instead. This allows the same command to be used to write the
password token to an NFC tag more conveniently.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The contents of the peer's capability and extended capability
information is required for the driver to perform TDLS P-UAPSD and Off
Channel operations. Pass this information to the driver when the peer
station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's HT capability and the QOS information is
required for the driver to perform TDLS operations. Pass this
information to the driver when the peer station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit a9a1d0f08a added vht_capabilities
to struct hostapd_sta_add_params but forgot to update
wpa_supplicant_tdls_peer_addset() to initialize the variable to NULL.
This could result in uninitialized pointer being used in
driver_nl80211.c when adding a TDLS peer entry. Fix this by clearing the
hostapd_sta_add_params with memset.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A TDLS Teardown frame with Reason Code 3 (Deauthenticated because
sending STA is leaving (or has left) IBSS or ESS) shall be transmitted
to all TDLS peer STAs (via the AP or via the direct path) prior to
transmitting a Disassociation frame or a Deauthentication frame to the
AP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
For various P2P use cases, it is useful to have more accurate timestamp
for the peer information update. This commit improves scan result
handling by using a single timestamp that is taken immediately after
fetching the results from the driver and then using that value to
calculate the time when the driver last updated the BSS entry. In
addition, more debug information is added for P2P peer updates to be
able to clearly see how old information is being used here.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of reporting only one connection handover message, report
completion of NFC connection handover with carrier record from both the
request and select messages.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only some P2P states were considered to postpone concurrent
station mode scans during group formation. Especially the WPS
provisioning step was skipped due to issues to scans run on the P2P
client interface (see commit fc6997b345).
This is not ideal since a concurrent scan can slow down group formation
considerably and potentially make it time out. Enforce p2p-in-progress
through all steps of group formation on another interface to address
this.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Group formation timeout is normally canceled when 4-way handshake is
completed (WPA_COMPLETED -> wpas_p2p_completed). However, it is possible
for the GO to stop the group before this happens (i.e., send
Deauthentication frame with reason code 3 before 4-way handshake is
completed). This resulted in the group getting removed, but the group
formation timeout left behind. The unexpected timeout may then result in
undesired termination of the following operation. Fix this by canceling
the group formation timeout in wpas_p2p_group_delete() similarly to how
group idle timeout was canceled there.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since there could be multiple carrier records, it is cleaner to report
only the WPS carrier record instead of full NFC connection handover
select to wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since there could be multiple carrier records, it is cleaner to build
only the WPS carrier record instead of full NFC connection handover
request within wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit caff399250 added a property named
"WPS" to the dbus interface. It did not add the new
WPAS_DBUS_BSS_PROP_WPS property to the function responsible for marking
changed properties though. This cause the following messages to be
printed repeatedly to syslog:
dbus: wpas_dbus_bss_signal_prop_changed: Unknown Property value 7
Signed-hostap: Peter Wu <lekensteyn@gmail.com>
In addition to the offload mechanism, the Android configuration and
makefiles are extended to allow this to be configured for the build by
dropping in platform specific configuration files and makefile without
having to modify any existing files.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Usual manual scan request may cause reassociation due to several
reasons. New command is intended to perform pure scan without taking any
automatic action based on the results.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
On the DMG (60 GHz) band, capability bits defined differently from
non-DMG ones. Adjust capability matching to cover both cases.
Also, for non-DMG bands, check ESS bit is set.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
When AP mode operation reject the client, nl80211 layer advertises the
connect failed event with the reason for failures (for example, max
client reached, etc.) using NL80211_CMD_CONN_FAILED.
This patch adds some debug messages whenever such an event is received
from the nl80211 layer and also the same event is posted to the upper
layer via wpa_msg().
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
These channels were already enabled for P2P use, but the local
configuration parameter was not allowed to use the operating class in
which the 40 MHz channels are specified.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The RANGE=N1-N2 command did not return any entries in some cases where
N1 does not match with any BSS entry. Fix this by allow entries to be
fetched even without knowing the exact id values.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add the "BSS LAST ..." command. This command helps in fetching the scan
entries iteratively from FIRST entry to LAST entry by ID.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The "BSS FIRST.." command fails when additional parameters (e.g., MASK)
is used since the string comparsion does not take into account the
number of characters. Fix by comparing only 5 characters as in other
commands.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The HS 2.0 Indication element is 7 (not 6) octets. The previous
implementation could result in wpabuf validation code stopping the
program if HS 2.0 was enabled without Interworking or P2P (which would
have created a large enough buffer to avoid hitting this) being enable.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If an implicit TDLS set up request is obtained on an existing link or an
to be established link, the previous link was not removed. This commit
disables the existing link on a new set up request. Also,
wpa_tdls_reneg() function was invoking wpa_tdls_start() on an already
existing peer for the case of internal setup, which is incorrect. Thus
the invocation of wpa_tdls_start() is removed in wpa_tdls_reneg() and
also this function is renamed to wps_tdls_remove() as it does not
renegotiation rather shall remove the link (if any) for the case of
external setup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 50178335bf introduced a regression
for P2P-GROUP-STARTED event indication during p2p_connect-join when
using a separate P2P group interface. wpa_s->global->p2p_group_formation
was already set in that case to point to the group interface and this
commit changed this to point to incorrect interface. Fix this by setting
p2p_group_formation here only in case a separate group interface is not
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 59ff6653aa fixed this issue for
'removing a network', and we also need to take care of 'removing all
networks'.
Signed-hostap: Jaewan Kim <jaewan at google.com>
Addition of wpa_supplicant_fast_associate() made it unnecessary to call
wpas_select_network_from_last_scan() directly from other files.
Signed-hostap: Jouni Malinen <j@w1.fi>
If scan results are available when we perform a SelectNetwork, use
them to make an associate decision. This can save an entire scan
interval-worth of time in situations where something external to
wpa_supplicant (like a connection manager) has just previously
requested a scan before calling SelectNetwork.
Signed-hostap: Paul Stewart <pstew@chromium.org>
When the scan interval is changed the new interval is effective
after the old interval timer fires off one last time. This can cause
an unacceptable long delay when updating the interval.
Change this behaviour to use MIN(left of old interval, new interval)
for the scan interval following the interval change.
Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
The link was not disabled for the case of implicit trigger from the
driver unlike in the case of explicit trigger fromc ctrl_iface. Make the
tear down sequences match in these cases by adding the TDLS_DISABLE_LINK
tdls_oper to the driver when processing the TDLS_REQUEST_TEARDOWN event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Signal the start of EAP authentication as well as when additional
credentials are required to complete.
Signed-hostap: Paul Stewart <pstew@chromium.org>
Most of the variables are not needed anymore once the SAE instance
has entered Accepted state. Free these to save memory.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows FFC groups to be used with SAE. Though, these groups are not
included in the default sae_groups value based on what is available
since the FFC groups have the additional requirement of using a safe
prime with the current implementation (or specification of the group
order).
Signed-hostap: Jouni Malinen <j@w1.fi>
Even though this command is very unlikely to fail, in theory, it could
and the WPS connection would fail in such a case. Return more clearer
failure indication in such a case without even trying to start
reassociation.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new "sae_group=<id>" line will be included in the ctrl_iface STATUS
output if SAE was used for the association.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd.conf sae_groups parameter can now be used to limit the set of
groups that the AP allows for SAE. Similarly, sae_groups parameter is
wpa_supplicant.conf can be used to set the preferred order of groups. By
default, all implemented groups are enabled.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd can now be configured to use anti-clogging mechanism based on
the new sae_anti_clogging_threshold parameter (which is
dot11RSNASAEAntiCloggingThreshold in the standard). The token is
generated using a temporary key and the peer station's MAC address.
wpa_supplicant will re-try SAE authentication with the token included if
commit message is rejected with a token request.
Signed-hostap: Jouni Malinen <j@w1.fi>
The enum values for struct sae_data::state now match the protocol
instance states as defined in IEEE Std 802.11-2012, 11.3.8.2.2
Signed-hostap: Jouni Malinen <j@w1.fi>
The -N and -C command line parameters can be used to add arbitrary
RADIUS attributes to the messages. However, these were truncated to
about 128 bytes when the actually message was constructed. Fix this by
using larger buffers to allow the maximum attribute length (253 octets
of payload) to be used. [Bug 458]
Signed-hostap: Jouni Malinen <j@w1.fi>
The sizeof(ptr) use here was not correct and resulted in too small
memory block getting allocated for the -N command line argument.
Signed-hostap: Jouni Malinen <j@w1.fi>
In case of wpa_supplicant IBSS and AP modes after we will call wpa_cli
save command we should also save configured frequency. In other case
after wpa_supplicant restart we have frequency = 0 and AP start will
fail.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The GAS query compilation callback may happen after the wpa_supplicant
process has been requested to terminate. Avoid scheduling a new eloop
timeout for a scan in such a case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that the other BSS has actually received some valid ANQP
information before sharing the results from it. This fixes potential
issues with cases where some of the APs with the same HESSID has invalid
ANQP configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver rejected any of the offchannel Action frame TX requests,
the previous implementation terminated ANQP fetch process. While the
driver should not really reject the request normally, it is possible
that a request gets rejected for some reason. Allow the fetch process to
continue with the next AP in such case to avoid breaking networking
selection. This could result, e.g., in auto_interworking=1 process
failing to connect if any the driver rejects requests to any of the APs
in the scan result even if some other APs provided suitable information.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This was used to select between "(auth)" and "(reauth)" in
CTRL-EVENT-CONNECTED events. However, the variable was not cleared
anywhere else apart from the AP deinit case. As such, it did not really
provide correct information and is not really of much use even with
proper clearing added. As such, it is cleaner to just get rid of this
altogether.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit bb4d4deb4b introduced a code path
that could potentially end up calling wpa_config_update_psk() with NULL
passphrase. While that may not happen in practice, it is better to make
sure it doesn't happen since that function will dereference the
passphrase pointer unconditionally.
Signed-hostap: Jouni Malinen <j@w1.fi>
This continues optimizations for use of CPU heavy pbkdf2_sha1() in GO
setup after the earlier commit 30c371e8a5
by allowing PSK to be used instead of passphrase when creating
persistent group information manually for the GO.
It should be noted that this would not meet the requirements in the P2P
specification (GO shall maintain the passphrase), so this should be used
only when there is no need to allow manual configuration of legacy STAs
using the passphrase.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Cancel the existing supplicant scan and start a new supplicant
scan on PNO start and stop respectively. This makes sure that
supplicant scan is in progress when the device resumes.
Signed-off-by: Pandiyarajan Pitchaimuthu <c_ppitch@qca.qualcomm.com>
cfg80211 caches the scan results according the channel number. Due to
the 15 sec aging this might cause the user mode to see more than one
scan result with the same BSSID, e.g. - one scan result for the
P2P Device and one for the P2P GO (once it's enabled).
Fix this by updating the device entry only if the new peer entry is
newer than the one previously stored.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-hostap: Arik Nemtsov <arik@wizery.com>
The first "if" in the SCAN command handling didn't check properly for
sched_scan, causing the sched_scan and scan to run concurrently, instead
of cancelling the ongoing sched scan (which is handled by the "else if"
later).
Signed-hostap: Eliad Peller <eliad@wizery.com>
Add some more functionality for BSS Transition Management:
- advertise support for BSS Transition Management in extended
capabilities element
- add hostapd.conf parameter bss_transition=1 for enabling support
for BSS Transition Management
- add "hostapd_cli disassoc_imminent <STA> <num TBTTs>" for sending
disassociation imminent notifications for testing purposes
- wpa_supplicant: trigger a new scan to find another BSS if the
current AP indicates disassociation imminent (TODO: the old AP needs
to be marked to use lower priority to avoid re-selecting it)
Signed-hostap: Jouni Malinen <j@w1.fi>
The WNM-Sleep Mode handler took over WNM Action frame processing without
addressing the previously implemented WNM handler. Fix this by moving
the BSs Transition Management processing into wnm_sta.c to share a
single handler function for WNM Action frames.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need for p2p_supplicant.c to access wpa_s->pending_action_tx
so move these references to offchannel.c to get a bit cleaner interface
between the components.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 1ff733383f added a mechanism to
work around issues due to association events and EAPOL RX events being
getting reordered. However, this applied only for the case where
wpa_supplicant is not in associated state. The same issue can happen in
roaming case with drivers that perform BSS selection internally (or in
firmware). Handle that case similarly by delaying received EAPOL frame
processing if the source address of the EAPOL frame does not match the
current BSSID.
Since wired IEEE 802.1X do not have BSSID, make this additional
workaround conditional on BSSID match having been observed during the
previous association.
This fixes issues where the initial EAPOL frame after reassociation was
either dropped (e.g., due to replay counter not increasing) or replied
to with incorrect destination address (the BSSID of the old AP). This
can result in significantly more robust roaming behavior with drivers
that do not use wpa_supplicant for BSS selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Network blocks are disabled during a WPS provisioning step and 10
seconds after this to allow the newly provisioned network to be
selected. The disabled=1 flag gets written to the configuration file
when the credential is added since it happens during this process.
Update the file again after the networks have been re-enabled to avoid
leaving the configuration file into state that is not consistent with
the running configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 17a4734dc4 shall optimize the
post-WPS scan based on the channel used during the provisioning only
when the EAP-Failure frame is received. In cases where the EAP-Failure
frame is missed, this optimization shall not happen resulting in the
scan in all the channels thus consuming more time for the connection.
This commit enhances this by storing the requisite information after
the M8 frame is received.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Requires Linux kernel patch to make the SGI-20 properly disabled. SGI-40
will already work since Linux 3.4 or so.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Basic support for the 60 GHz band. Neither P2P nor WPS are yet taken
care off. Allows to start AP with very simple config:
network={
ssid="test"
mode=2
frequency=60480
key_mgmt=NONE
}
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_cancel did not properly cancel a pending p2p_connect-join operation.
Address the different steps in that process: initial scan, Provision
Discovery exchange before connection, and WPS provisioning step
(including the scans before WPS).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the NAI Realm list indicates that EAP-PEAP is used, use EAP-MSCHAPv2
as the Phase 2 method by default if the NAI Realm list does not specify
the tunneled method.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit e99b4f3a14 added functionality to
check whether the current association is with the home SP. This commit
did not take into account that the domain name ANQP information could be
NULL and that could result to a NULL pointer dereference. Fix that by
validation that domain_names != NULL before calling
domain_name_list_contains().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Replace CONFIG_IEEE80211V with CONFIG_WNM to get more consistent build
options for WNM-Sleep Mode operations. Previously it was possible to
define CONFIG_IEEE80211V without CONFIG_WNM which would break the build.
In addition, IEEE 802.11v has been merged into IEEE Std 802.11-2012 and
WNM is a better term to use for this new functionality anyway.
Signed-hostap: Jouni Malinen <j@w1.fi>
These fields do not use AES keywrap. Instead, they are protected with
management frame protection (and not included if PMF is disabled).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The optional tfs_req=<hex dump> parameter can be added for the wnm_sleep
command to specify the TFS request element to use in the WNM-Sleep Mode
Request frame.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This code was within ifdef CONFIG_AP and did not get included unless
AP mode support was also enabled.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new excluded_ssid parameter within a cred block can be used to
excluded networks from matching with credentials.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Number of cred block fields were not saved when wpa_supplicant is
writing the configuration file.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the AP does not advertize EAP parameters, default to TTLS/MSCHAPv2
when using username/password credentials.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The current PMKSA cache entry needs to be clear to allow EAPOL
reauthentication to be started in case this association used PMKSA
caching.
Signed-hostap: Jouni Malinen <j@w1.fi>
Both the ctrl_iface and D-Bus interface use similar functionality to
request a new connection. Combine these to a single function to avoid
need to maintain duplicated implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpas_connection_failed() uses the blacklist count to figure out a
suitable time to wait for the next scan. This mechanism did not work
properly in cases where the temporary blacklist gets cleared due to no
other BSSes being available. Address this by maintaining an additional
count of blacklisting values over wpa_blacklist_clear() calls. In
addition, add one more step in the count to timeout mapping to go to 10
second interval if more than four failures are seen.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the driver does not support multi-channel concurrency and a virtual
interface that shares the same radio with the current interface is
operating there may not be need to scan other channels apart from the
current operating channel on the other virtual interface. Filter out
other channels in case we are trying to find a connection for a station
interface when we are not configured to prefer station connection and a
concurrent operation is already in process.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the global pmf=1/2 parameter is used to enable PMF for Interworking
networks, add WPA-EAP-SHA256 to the temporary network block to allow
connection to PMF required APs.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, PMF (protected management frames, IEEE 802.11w) could be
enabled only with a per-network parameter (ieee80211w). The new global
parameter (pmf) can now be used to change the default behavior to be PMF
enabled (pmf=1) or required (pmf=2) for network blocks that do not
override this with the ieee80211w parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
We enable this feature for non-SME drivers as well if
they explicitly indicate need for it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
This prevents situations like the following where we roam to a
lesser quality BSS just because the signal level delta is over our
threshold.
wlan0: Considering within-ESS reassociation
wlan0: Current BSS: 00:24:6c:74:0a:40 level=-51
wlan0: Selected BSS: 00:24:6c:74:0a:e0 level=-64
wlan0: Request association: reassociate: 0 selected: 00:24:6c:74:0a:e0
bssid: 00:24:6c:74:0a:40 pending: 00:00:00:00:00:00 wpa_state: COMPLETED
Signed-hostap: Robert Shade <robert.shade@gmail.com>
This allows the ctrl_iface STATUS information to be used to determine
which Home SP credential (domain in the cred block) was used and whether
the network is operated by the home SP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows credential entries to be removed based on SP FQDN without
having to iterate through the configured entries from an external
program to figure out which credentials should be removed for a specific
SP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the credential that was used to create a temporary HS 2.0 network
block is removed, remove the network block, too.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant is started from /init.*.rc on Android and that seems
to be using umask 0077 which would leave the control interface
directory without group access. This breaks things since Wi-Fi
framework assumes that this directory can be accessed by other
applications in the wifi group. Fix this by adding group access even
if umask value would prevent this.
In most cases, this issue was not hit since the control interface
directory is normally created by that same init.*.rc file with suitable
mode and wpa_supplicant is killed in the way that does not allow it to
remove the file. However, if wpa_supplicant is allowed stop cleanly, it
will remove the directory and the next start could result with the Wi-Fi
framework not being able to use Wi-Fi (and GUI not showing Wi-Fi getting
enabled).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The PD Request retry limit can be used to achieve the same behavior,
so drop this duplicated timeout mechanism and control the timeout
based on MAX_PROV_DISC_REQ_RETRIES.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The GO may be in sleep when we send a PD Request frame to indicate that
we are about to join a running group. Previously, this frame was not
retried more than normal low level retries. This can result in the GO
not getting the frame especially in cases where concurrent multi-channel
operations or aggressive sleep schedule is used since most drivers do
not yet synchronize with the GO's NoA before association.
Increase the likelihood of the GO receiving the PD Request frame by
retransmitting it similarly to the PD-for-GO-Negotiation case. Start
the actual join operation only after these retries have failed to get
an acknowledgment from the GO to give the connection attempt a chance
to succeed if the driver implements better NoA synchronization for it.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_prov_disc_req() used the join parameter to figure out whether the PD
request was a user initiated or not. This does not cover all use cases
of PD, so add a separate parameter to allow caller to indicate whether
the user requested the operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit ee431d77a5 broke wpa_supplicant
compilation:
../src/ap/ieee802_1x.o: In function `ieee802_1x_get_eap_user':
/../src/ap/ieee802_1x.c:1689: undefined reference to `hostapd_get_eap_user'
collect2: error: ld returned 1 exit status
make: *** [wpa_supplicant] Error 1
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Some network parameters, e.g., auth_alg and eap use a space separated
list of values without quotation marks. To allow these to be entered
from the interactive mode, change set_network command to allow more than
three arguments.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds description of the main changes from the forking of
hostap-1.git for 1.x releases to the current master branch snapshot.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commits 07783eaaa0 and
3da372fae8 removed the only users of the
disassociate() driver operation, so these driver wrapper functions can
also be removed now.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 620c783753 modified
wpas_wps_ssid_wildcard_ok() prototype, but forgot to update the
non-WPS-build wrapper. Fix that to match with the new bss parameter
type and remove the now unused declaration of wpa_scan_res.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, OKC (opportunistic key caching, a.k.a. proactive key
caching) could be enabled only with a per-network parameter
(proactive_key_caching). The new global parameter (okc) can now be used
to change the default behavior to be OKC enabled (okc=1) for network
blocks that do not override this with the proactive_key_caching
parameter.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If separate group interfaces are used, the pending group interface got
removed unnecessarily when stopping find operations when accepting an
invitation to reinvoke the group in GO role. This resulted in the group
interfaces getting created twice. Avoid this unnecessary extra operation
by skipping removal of the pending interface in the reinvocation
sequence.
Signed-hostap: Jouni Malinen <j@w1.fi>
In highly congested network (BSSes almost on every channel
within ESS) we have hit a bug when wpa_supplicant become
completly irresponsive, infinite looping on while loop.
When probe_idx was equal 0 and we are not able to probe
new frequency, following condition were never fulfilled:
"if (!in_array(freqs, data->supp_freqs[idx]))"
Signed-hostap: Pawel Kulakowski <pawel.kulakowski@tieto.com>
The UFD (USB flash drive) configuration method was deprecated in WSC
2.0. Since this is not known to be used, remove the UFD implementation
from hostapd and wpa_supplicant to allow the WPS implementation to be
cleaned up. This removes the now unused OOB operations and ctrl_iface
commands that had already been deprecated by the new NFC operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
The PSK generation done by pbkdf2_sha1() is one of the longest CPU time
users according to our profiling from boot to GO started.
So I have reduced some steps.
I could boot a GO by this command sequence.
-------------
add_net
set_network 0 ssid '"DIRECT-XX"'
set_network 0 psk
'"123456789012345678901234567890123456789012345678901234567890123"'
set_network 0 proto RSN
set_network 0 key_mgmt WPA-PSK
set_network 0 pairwise CCMP
set_network 0 auth_alg OPEN
set_network 0 mode 3
set_network 0 disabled 2
p2p_group_add persistent=0 freq=2412
-------------
By this sequence, pbkdf2_sha1() was called three times and the function
calculates the same value each time. Reduce number of calls to
pbkdf2_sha1() from 3 to 1 by caching the previous result.
Signed-hostap: Masashi Honma <masashi.honma at gmail.com>
There are a few instances where dbus handlers test the value
of errno to test whether strtoul completes successfully.
Since strtoul does not clear errno, and there's no strong
reason to suspect that errno is already clear, it is safer
to clear it right before calling strtoul. Also, any failure
in strtoul (setting errno non-zero) should be considered a
failure.
While testing using dbus-send, I found that a malformed
network path can cause a crash due to net_id being left
NULL. We should test for this before calling strtoul
on it.
Tested with:
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
org.freedesktop.DBus.Properties.Get \
string:fi.w1.wpa_supplicant1.Interface string:Networks
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.RemoveNetwork \
objpath:/fi/w1/wpa_supplicant1/Interfaces/0/Networks/0
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.RemoveNetwork \
objpath:/fi/w1/wpa_supplicant1/Interfaces/0/Networks/0
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.RemoveNetwork \
objpath:/fi/w1/wpa_supplicant1/Interfaces/0
Signed-hostap: Paul Stewart <pstew@chromium.org>
intended-for: hostap-1
This function is now unused after the last couple of commits that
removed the last uses, so remove this to keep code simpler since all
places that disassociate, can use deauthentication instead.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
cfg80211/mac80211 may reject disassociation command if association has
not yet been formed. Use deauthentication in cases where it is possible
that we are associating at the moment the command is issued.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant_{disassociate,deauthenticate}() need to inform the driver
about decision to disconnect even if this happens during the time when
the driver is still trying to complete association. During that time,
wpa_s->bssid is not set, so the code in these functions needs to figure
out the correct BSSID based on that field or wpa_s->pending_bssid. In
addition, it is possible that the BSSID is not even known at
wpa_supplicant at this point in time when using drivers that perform BSS
selection internally. In those cases, the disconnect command needs to be
sent to the driver without the BSSID.
This fixes issues where the driver (or cfg80211 in particular) may be
left in mismatching state with wpa_supplicant when disconnection (e.g.,
due to a ctrl_iface command) happens between connection request and
association event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This helper script can now handle both reading of a NFC tag and
initiation of NFC connection handover if a peer NFC device is touched.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the driver indicates the association (or authentication) was
rejected, wpa_supplicant should handle this connection failure similarly
to other cases. Previously, this was only handled with drivers that use
wpa_supplicant SME.
In case of cfg80211-based drivers, a rejected association was actually
already handled since cfg80211 generates a deauthentication event after
indicating connection failure. However, rejected authentication resulted
in wpa_supplicant waiting for authentication timeout to expire which is
unnecessary long wait.
Fix this by calling wpas_connection_failed() to use the common mechanism
to reschedule a new connection attempt with the previously attempted
BSSID blacklisted.
Signed-hostap: Jouni Malinen <j@w1.fi>
If WPS Registrar tries to provision a WPA/WPA2-Personal network without
including a valid Network Key, the network block cannot be used to
connect to the network. Reject such credential without adding the
network block. This makes wpa_supplicant send WSC_NACK as a response to
the invalid Credential and stop the provisioning process immediately
rather than only after trying unsuccessfully to connect to the network.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The DNS Name is allowed to use or not use domain name compression. To
handle both cases, check human readable DNS Name match if binary
matching does not show a hit.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There may be multiple Bonjour PTR matches for the same key, so extend
the P2P SD code for this to allow such entries to be added (i.e., do not
override previously added value, but add a new one). Similarly, return
multiple matches (one per Service TLV) for a query if it happens to
match more than a single configured Bonjour service.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new P2P_SET parameter disc_int can now be used to configure
discoverable interval for p2p_find operations. The format of the command
for setting the values is "P2P_SET disc_int <minDiscoverableInterval>
<maxDiscoverableInterval> <max TUs for discoverable interval>". The
first two parameters are given in units of 100 TUs (102.4 ms). The third
parameter can be used to further limit the interval into a specific TU
amount. If it is set to -1, no such additional limitation is enforced.
It should be noted that the P2P specification describes the random
Listen state interval to be in units of 100 TUs, so setting the max TU
value to anything else than -1 is not compliant with the specification
and should not be used in normal cases. The default parameters can be
set with "P2P_SET disc_int 1 3 -1".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver rejects the scan request while handling an external
requested scan (e.g., SCAN command on ctrl_iface), wpa_s->scan_req gets
cleared in wpa_supplicant_scan(). This can results in issues when the
scheduled re-try of the scan in one seconds trigger another call to this
function. If ap_scan==2 mode is used, this would result in new
association attempt instead of a new scan. Avoid this by restoring value
of wpa_s->scan_req in case the scan trigger fails and a new scan attempt
is scheduled.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpas_p2p_pd_before_join_timeout() needs to clear the
pending_pd_before_join flag to match other uses of this flag prior to
calling wpas_p2p_join_start(). Without this, the flag could be left set
which can cause following P2P operations to behave in unexpected ways.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new p2p_no_group_iface=1 configuration parameter can now be used to
disable the default behavior of adding a separate interface for the P2P
group when driver support for concurrent interfaces is available.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 0d30cc240f forced
wpa_s->current_ssid to be cleared in wpa_supplicant_mark_disassoc()
which gets called from wpa_supplicant_event_disassoc(). This breaks the
P2P group idle mechanism for the case where p2p_group_idle is not set
(i.e., is the default 0) since wpas_p2p_group_idle_timeout() ignores the
timeout in that case if the interface is not recognized as a client
interface (which was based on wpa_s->current_ssid being set).
Fix this by making wpas_p2p_is_client() default to client case if
wpa_s->current_ssid is NULL. This is much more likely case since the P2P
GO mode operation would not really clear the pointer without explicit
request to disconnect.
Signed-hostap: Jouni Malinen <j@w1.fi>
The old WPS interface for using NFC has no known deployments and even
the binary libraries referenced here are not easily available anymore.
Since the new interface for using NFC with WPS covers the same
functionality, remove the old implementation to clean up WPS
implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
When WPS is used with NFC connection handover, the AP may indicate its
operating channel within the credential information. Use this
informatiom, if present, to speed up the scan process.
Signed-hostap: Jouni Malinen <j@w1.fi>
This commit adds new wpa_supplicant ctrl_iface commands to allow
external programs to go through NFC connection handover mechanism
with wpa_supplicant taking care of the WPS processing. This version
includes only the case where wpa_supplicant is operating as a
station/Enrollee.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the driver indicates support for multi-channel concurrency, change
the p2p_connect behavior to not force the current operating channel, but
instead, just mark it as preferred for GO Negotiation. This change
applies only for the case when the freq parameter is not used with the
p2p_connect command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the P2P_PEER command to be used to fetch the list of
secondary device types that each P2P peer has advertised.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
P2P includes two use cases where one of the devices is going to start a
group and likely change channels immediately after processing a frame.
This operation may be fast enough to make the device leave the current
channel before the peer has completed layer 2 retransmission of the
frame in case the ctrl::ack frame was lost. This can result in the peer
not getting TX status success notification.
For GO Negotiation Confirm frame, p2p_go_neg_conf_cb() has a workaround
that ignores the TX status failure and will continue with the group
formation with the assumption that the peer actually received the frame
even though we did not receive ctrl::ack. For Invitation Response frame
to re-invoke a persistent group, no such workaround is used in
p2p_invitation_resp_cb(). Consequently, TX status failure due to lost
ctrl::ack frame results in one of the peers not starting the group.
Increase the likelihood of layer 2 retransmission getting acknowledged
and ctrl::ack being received by waiting a short duration after having
processed the GO Negotiation Confirm and Invitation Response frames for
the re-invocation case. For the former, use 20 ms wait since this case
has been worked around in deployed devices. For the latter, use 50 ms
wait to get even higher likelihood of getting ctrl::ack through since
deployed devices (and the current wpa_supplicant implementation) do not
have a workaround to ignore TX status failure.
20 ms is long enough to include at least couple of retries and that
should increase likelihood of getting ctrl::ack through quite a bit. The
longer 50 ms wait is likely to include full set of layer 2 retries.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the wpa_cli wps_pin command to support specification of the PIN
expiration time in seconds similarly to hostapd_cli wps_pin command when
using wpa_supplicant for AP mode (including P2P GO).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
By default, P2P is enabled globally for all virtual interfaces and this
makes wpa_supplicant include WSC and P2P IEs in Probe Request frames for
all scans even if this is for a non-P2P station connection to speed up
device discovery. If an interface is dedicated for non-P2P station mode
operations, it is now possible to disable addition of WSC and P2P IEs
into Probe Request frames with a per-interface p2p_disabled parameter.
This can be set either in the configuration file (p2p_disabled=1) or at
run time ("wpa_cli -i wlan0 set p2p_disabled 1"). Unlike the previous
mechanism ("wpa_cli p2p_set disabled 1"), the new parameter changes the
behavior only for the specified interface while other interfaces
continue to follow the global P2P enabled/disabled state.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The bssid and priority parameters in a network block do not have any
effect on the validity of a PMKSA cache entry, so avoid flushing the
PMKSA cache when only these parameters are changed. This is mainly
to allow forced roaming or network selection changes without causing
a disconnection if the changes are done during RSN association that
used EAP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add a function to filter out known cases of disconnection during 4-way
handshake that are caused by something else than mismatch in PSK. This
commit adds the case where the local end determines a mismatch in
WPA/RSN element between Beacon/Probe Response frames and EAPOL-Key msg
3/4.
This can avoid some potentially confusing "WPA: 4-Way Handshake failed -
pre-shared key may be incorrect" ctrl_iface messages.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This replaces the previously used bogus test data in SAE messages with
the first real field. The actual SAE authentication mechanism is still
missing and the Scaler, Element, and Confirm fields are not included.
Signed-hostap: Jouni Malinen <j@w1.fi>
If wpa_s->current_ssid is not set (e.g., after disconnection that
did not result in immediate group removal), an incorrect group could
have been removed since the network block iteration here could select
the network block that is used to store persistent group credentials.
Fix this by verifying that disabled != 2 to avoid picking the network
block that could not have been the temporary P2P group.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
During the association for the WPS handshake all the other configured
networks are disabled. This patch makes wpa_supplicant reenable the
disabled networks after the success/failure of the WPS handshake.
Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
When ANQP_GET or HS20_ANQP_GET is used to request ANQP information,
unshare the ANQP information (i.e., create a per-BSS copy of it) to
make sure the information from the specified BSS is available in case
the APs provide different information within HESSID.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds parsed version of WAN Metrics information to the control
event message as follows:
RX-HS20-ANQP 02:00:00:00:01:00 WAN Metrics 01:8000:1000:80:240:3000
format: <WAN Info>:<DL Speed>:<UL Speed>:<DL Load>:<UL Load>:<LMD>
WAN Info: B0-B1: Link Status, B2: Symmetric Link, B3: At Capabity
(encoded as two hex digits)
Downlink Speed: Estimate of WAN backhaul link current downlink speed in kbps;
1..4294967295; 0 = unknown
Uplink Speed: Estimate of WAN backhaul link current uplink speed in kbps
1..4294967295; 0 = unknown
Downlink Load: Current load of downlink WAN connection (scaled to 255 = 100%)
Uplink Load: Current load of uplink WAN connection (scaled to 255 = 100%)
Load Measurement Duration: Duration for measuring downlink/uplink load in
tenths of a second (1..65535); 0 if load cannot be determined
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 620c783753 modified
wpas_wps_ssid_bss_match() prototype but forgot to update the non-WPS
wrapper inline function. Fix that to match with the new bss parameter
type.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When specified in the conf file this parameter will make all invocations
of p2p_group_add, p2p_connect, and p2p_invite behave as if "ht40" has
been specified on the command line. This shouldn't do harm since
regulatory constraints and driver capabilities are consulted anyway
before starting HT40 mode.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
This introduces new AKM for SAE and FT-SAE and adds the initial parts
for going through the SAE Authentication frame exchange. The actual SAE
algorithm and new fields in Authentication frames are not yet included
in this commit and will be added separately. This version is able to
complete a dummy authentication with the correct authentication
algorithm and transaction values to allow cfg80211/mac80211 drivers to
be tested (all the missing parts can be handled with
hostapd/wpa_supplicant changes).
Signed-hostap: Jouni Malinen <j@w1.fi>
Otherwise it's difficult to determine if the supplicant was built with
CONFIG_AP, CONFIG_IBSS_RSN, CONFIG_P2P, etc. CONFIG_AP and CONFIG_P2P
can be inferred from the introspection data of the Interface object,
but CONFIG_IBSS_RSN does not change the introspection data at all and
thus it's impossible to determine whether the supplicant supports it
without knowing its compile-time options.
Signed-hostap: Dan Williams <dcbw@redhat.com>
intended-for: hostap-1
The wpa_s->p2p_in_provisioning flag did not get cleared in some cases
where p2p_cancel command is used to stop group formation. This can result
in some operations (like p2p_find) failing afterwards. Fix this by using
wpas_group_formation_completed() when processing p2p_cancel for a group
that has not yet completed group formation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the keystore:// prefix is used in the private_key entry, convert that
to the OpenSSL engine style configuration used for Android JB keystore.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The pending GAS entry must be removed from the list when it is removed.
This fixes an issue with potential segfault due to freed memory being
accessed if the driver fails to accept a GAS query.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
External programs can use this new parameter to prevent wpa_supplicant
from connecting to a list of BSSIDs and/or SSIDs. The disallowed BSSes
will still be visible in scan results and it is possible to run ANQP
operations with them, but BSS selection for connection will skip any
BSS that matches an entry in the disallowed list.
The new parameter can be set with the control interface SET command
using following syntax:
SET disallow_aps <disallow_list>
disallow_list ::= <ssid_spec> | <bssid_spec> | <disallow_list> | “”
SSID_SPEC ::= ssid <SSID_HEX>
BSSID_SPEC ::= bssid <BSSID_HEX>
For example:
wpa_cli set disallow_list "ssid 74657374 bssid 001122334455 ssid 68656c6c6f"
wpa_cli set disallow_list
(the empty value removes all entries)
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the P2P client group to be removed while waiting for
a pending scan operation (e.g., when p2p_group_idle timeout hits after
getting disconnected from the GO with something else than
Deauthentication with reason code 3). If this happens with a P2P
interface that is used both for P2P Device and group roles, scan state
could get stuck while waiting for the next scan to complete since no
more station (P2P client) mode scans are scheduled. Fix this by clearing
sta_scan_pending when removing the temporary group network block.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make Invitation process for re-invoking a persistent group behave
similarly to GO Negotiation as far as channel negotiation is concerned.
The Operating Channel value (if present) is used as a starting point if
the local device does not have a forced operating channel (e.g., due to
concurrent use). Channel lists from devices are then compared to check
that the selected channel is in the intersection. If not, channel is
selected based on GO Negotiation channel rules (best channel preferences
etc.). Invitation Request is rejected if no common channel can be
selected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If two P2P_FIND commands and a station mode SCAN command are issued in a
sequence with the second P2P_FIND and SCAN commands started before the
initial scan from the first P2P_FIND command has completed,
sta_scan_pending may be left set without an automatic way of getting it
cleared. This can get P2P search stuck if no further station mode scan
operations are run.
Fix this by clearing the sta_scan_pending flag whenever station mode scans
are stopped due to no enabled networks resulting in INACTIVE mode getting
entered. In addition, avoid setting sta_scan_pending flag when a special
scan_res_handler is set so that this does not get enabled on the P2P
Device interface during a P2P search operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there are any disabled networks, show a debug print with the count
of those networks when no enabled networks are found. This can be
helpful in trying to figure out why scans are being skipped.
Signed-hostap: Jouni Malinen <j@w1.fi>
The ASCII hexdump is somewhat difficult to search for (especially on
Android builds), so make the debug log easier to parse by printing the
full control interface command as a text string. In addition, use
wpa_dbg() to get the interface name printed so that multi-interface
cases can be debugged.
Signed-hostap: Jouni Malinen <j@w1.fi>
Setting just ssid->passphrase is not enough to complete the network
block for the GO entry. Also the PSK needs to be derived so that the
network is considered enabled by wpas_network_disabled(). The previous
version worked as long as something else allowed the scan request to be
performed (this is needed even though the actual scan is skipped when
starting GO).
The first GO start was allowed because wpa_s->scan_req is initialized to
1 in wpa_supplicant_alloc(). However, other attempts may fail if
wpa_s->scan_req is cleared. This failure shows up as "No enabled
networkas - do not scan" in debug log followed by state change to
INACTIVE when trying to start GO.
Fix this by deriving PSK from the passphrase for GO mode.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 30ee769235 started skipping P2P
group removal if wpa_s->current_ssid is not set and commit
0d30cc240f started clearing
wpa_s->current_ssid on disconnection. This combination broke
p2p_group_idle timeout on P2P client interface in a case where no
separate P2P group interface is used and when the disconnection is
triggered by something else than an explicit indication of GO
terminating the group.
Fix this by relaxing network block matching rules when figuring out
whether any of the configured network blocks could be in P2P use. The
p2p_group flag alone should be enough for this since temporary P2P group
network blocks are removed once the P2P group is terminated.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the AP creation failed (missing freq= or driver error) the supplicant
would previously stay in SCANNING state forever. Instead, it should
handle the error a bit better and drop back to DISCONNECTED so clients
know something went wrong.
Signed-hostap: Dan Williams <dcbw@redhat.com>
intended-for: hostap-1
Channel 14 is available only in Japan and is DSSS-only according to
IEEE 802.11-2012 19.4.3 and MIC Equipment Ordinance (EO)
for Regulating Radio Equipment article 49.20.
At the same time, P2P should avoid using DSSS modulation in normal
operation according to P2P specification v1.2 2.4.1.
Signed-hostap: Mykyta Iziumtsev <mykyta.iziumtsev@gmail.com>
intended-for: hostap-1
Commit 4d32c0c44d added another use for the
local pos variable and that broke the mechanism used to determine wheter
the peer address was provided. Fix this by using a separate pointer to the
peer address.
Signed-hostap: Jouni Malinen <j@w1.fi>
When I use CONFIG_WPS_NFC=y a warning appears.
wps_supplicant.c:1872:12: warning: 'wpas_wps_add_nfc_password_token'
defined but not used [-Wunused-function]
This patch removes this warning.
Signed-hostap: Masashi Honma <masashi.honma at gmail.com>
If a connection operation is started on an interface based on scan
results, other virtual interfaces should not be information about the
results to avoid potential concurrent operations during the association
steps. Since the sibling notification of scan results received was added
as an optimization, skipping it for this type of cases is the simplest
way of avoiding unnecessary concurrent operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes sure that the interrupted station mode scan can be completed
after the P2P operations have had their chance of using the radio.
Signed-hostap: Jouni Malinen <j@w1.fi>
Driver could reject the new scan based on any virtual interface
running a concurrent scan. As such, mark the pending scan callback
for P2P based on any interfaces instead of just the one used for
the p2p_scan operation.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since we have a global P2P module, the flag to trigger scan completion
events to it needs to be in similar context. The previous design
maintained this separately for each virtual interface and if P2P module
did not run its scan operation on the virtual interface that completed
the scan, P2P module would not be allowed to restart operations
properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
The BSS pointer may change if the entry needs to be reallocated
and the new pointer has to be added to the last_scan_res array
to avoid using pointers to freed memory.
Signed-hostap: Jouni Malinen <j@w1.fi>
If two BSS entries have the same HESSID and SSID, share the fetched ANQP
information between these BSS entries to save memory and GAS/ANQP
operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The eap parameter in the cred block can now be used to override
automatic EAP-SIM/AKA/AKA' selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is an initial step in allowing the ANQP responses to be shared
among multiple BSSes if the BSSes are determined to be operating under
identical configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the REMOVE_NETWORK command is used to delete the currently connected
network, some operations were run between removing the network and
clearing of wpa_s->current_ssid. This left wpa_s->current_ssid pointing
to freed memory and should any operation end up using it before the
pointer gets cleared, freed memory could be references. Avoid this by
removing the network only after having completed the operations that
clear wpa_s->current_ssid.
Signed-hostap: Deepthi Gowri <deepthi@codeaurora.org>
intended-for: hostap-1
Use configured credentials to figure out which ANQP information needs to
be fetched and only fetch those when using Interworking network
selection. The fetch_anqp command is still fetching all ANQP
information.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the scan results from before ANQP fetch are fresh (less than five
seconds old), do not run a new scan when selecting the BSS after having
used Interworking network selection.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the BSS selection functions to be called without having the
scan result data structure. This can be used to skip extra scans in
cases where previous results can be considered fresh.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows last results to be used even after they have been freed
since the information is copied to the BSS entries anyway and this new
array provides the order in which scan results were processed.
Signed-hostap: Jouni Malinen <j@w1.fi>
The same information is available in the BSS table, so we can reduce the
need for using the raw scan results in wpa_supplicant_need_to_roam().
Signed-hostap: Jouni Malinen <j@w1.fi>
Use the anonymous_identity field to store EAP-SIM/AKA pseudonym identity
so that this can be maintained between EAP sessions (e.g., after
wpa_supplicant restart) even if fast re-authentication data was cleared.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 0d30cc240f forced
wpa_s->current_ssid to be cleared in wpa_supplicant_mark_disassoc()
which gets called from wpa_supplicant_event_disassoc(). This broke SME
disassoc-while-authenticating workaround for cfg80211. Fix this by
restoring wpa_s->current_ssid in case SME authentication is in progress.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 0d30cc240f forced
wpa_s->current_ssid and wpa_s->key_mgmt to be cleared in
wpa_supplicant_mark_disassoc() which gets called from
wpa_supplicant_event_disassoc(). This broke IEEE 802.1X authentication
failure processing and P2P deauthentication notification (group
termination).
Fix this by splitting wpa_supplicant_event_disassoc() into two parts and
make wpas_p2p_deauth_notif() indicate whether the interface was removed.
If so, the last part of disassocition event processing is skipped. Since
the wpa_supplicant_mark_disassoc() call is in the second part, the above
mentioned issues are resolved. In addition, this cleans up the P2P group
interface removal case by not trying to use fast reconnection mechanism
just before the interface gets removed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The wpa_s->current_ssid pointer may get cleared, e.g., when
disconnected. Commit 30ee769235 made
wpas_p2p_group_delete() exit early before removing a P2P interface in
this type of case. That can cause number of issues from p2p_group_remove
command failing to busy loop when terminating wpa_supplicant if there is
a P2P group interface in client mode and that interface happens to be in
disconnected state. Fix these issues by allowing wpas_p2p_group_delete()
remove the P2P group interface regardless of whether wpa_s->currnt_ssid
is set.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The freq and ht40 parameters can now be used with the p2p_invite
command when reinvoking a persistent group as the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The variables used within the #ifndef block here needs to be defined in
the beginning of the function to avoid issues with some compilers.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit does not yet address support for different device roles,
i.e., the same set of subelements are returned regardless of which
role was indicated in the request.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_cli p2p_serv_disc_req command can now be used to request WSD
request to be sent to specified or all peers who support WSD.
format: wifi-display <list of roles> <list of subelements>
examples:
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source] 2,3,4,5
p2p_serv_disc_req 02:01:02:03:04:05 wifi-display [pri-sink] 3
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [sec-source] 2
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source+sink] 2,3,4,5
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source][pri-sink] 2,3,4,5
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds control interface commands and internal storage of
Wi-Fi Display related configuration. In addition, WFD IE is now added
to various P2P frames, Probe Request/Response, and (Re)Association
Request/Response frames. WFD subelements from peers are stored in the
P2P peer table.
Following control interface commands are now available:
SET wifi_display <0/1>
GET wifi_display
WFD_SUBELEM_SET <subelem> [hexdump of length+body]
WFD_SUBELEM_GET <subelem>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows both hostapd and wpa_supplicant to be used to derive and
configure keys for GCMP. This is quite similar to CCMP key
configuration, but a different cipher suite and somewhat different rules
are used in cipher selection. It should be noted that GCMP is not
included in default parameters at least for now, so explicit
pairwise/group configuration is needed to enable it. This may change in
the future to allow GCMP to be selected automatically in cases where
CCMP could have been used.
This commit does not included changes to WPS or P2P to allow GCMP to be
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit b49039bda9 redesigned tab
completion, but added the new call to completion functions into wrong
location. This needs to be done within the loop to find the correct
completion function.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
auto_interworking=1 configuration parameter can be used to request
wpa_supplicant to use Interworking network selection automatically as a
part of the normal (non-Interworking) network selection if the scan
results do not match with enabled networks. This makes scanning work
similarly to the "interworking_select auto" command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new gas_request and gas_response_get commands can be used to request
arbitary GAS queries to be performed. These can be used with ANQP or
with other (including vendor specific) advertisement protocols.
gas_request <BSSID> <AdvProtoID> [Query]
gas_response_get <addr> <dialog token> [offset,length]
For example, ANQP query for Capability list in interactive wpa_cli
session:
> gas_request 02:00:00:00:01:00 00 000102000101
<3>GAS-RESPONSE-INFO addr=02:00:00:00:01:00 dialog_token=0
status_code=0 resp_len=32
> gas_response_get 02:00:00:00:01:00 00
01011c00010102010501070108010c01dddd0c00506f9a110200020304050607
> gas_response_get 02:00:00:00:01:00 00 0,10
01011c00010102010501
> gas_response_get 02:00:00:00:01:00 00 10,10
070108010c01dddd0c00
> gas_response_get 02:00:00:00:01:00 00 20,10
506f9a11020002030405
> gas_response_get 02:00:00:00:01:00 00 30,2
0607
It should be noted that the maximum length of the response buffer is
currently 4096 bytes which allows about 2000 bytes of the response data
to be fetched with a single gas_response_get command. If the response is
longer, it can be fetched in pieces as shown in the example above.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Clear the possible blacklisting of a WPS AP during WPS PIN iteration if
the AP moves to selected registrar TRUE state or if it adds our MAC
address to the list of authorized MACs.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Maintain state of WPS APs during iteration to find the correct AP for
WPS PIN operation when no specific BSSID is specified. This information
can be used for optimizing the order in which the APs are tried. This
commit is only adding the collection of the information and more
detailed debug information to make debug logs more helpful in figuring
out how the AP selection order could be improved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes wpa_supplicant state somewhat cleaner since the information
from previously used connection is not maintained after getting
disconnected.
Signed-hostap: Jouni Malinen <j@w1.fi>
If 4-way handshake fails due to likely PSK failure or if EAP
authentication fails, disable the network block temporarily. Use longer
duration if multiple consecutive failures are seen.
Signed-hostap: Jouni Malinen <j@w1.fi>
"help <cmd>" can now be used to print the usage text for the
specified command (or set of commands matching the prefix).
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of using a separate list of commands, use the main command table
to assign tab completion functions. In addition, use the existing BSS
and P2P peer completions functions with the commands that use BSSID or
P2P Device address the first argument.
Signed-hostap: Jouni Malinen <j@w1.fi>
The NAI building routine assumed that the credential included the IMSI,
but that is not the case when using a real SIM card. Build the NAI based
on the IMSI read for the card in such a case.
Signed-hostap: Jouni Malinen <j@w1.fi>
The pos variable was not advanced when comparing PLMN entries in
3GPP Cellular Network information and as such, only the first
entry was really used.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
This can be used to test new control interface commands and to use
commands that may not yet be supported by wpa_cli.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the P2P management operations are handled within the driver, the
P2P service entries were not freed when terminating wpa_supplicant.
Fix this by calling wpas_p2p_service_flush() even if the P2P module
within wpa_supplicant has not been initialized.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This limits the maximum size of the p2p_client_list parameter that
is maintained at the GO for a persistent group. In other words, only
the 100 most recently seen P2P clients are kept in the list.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
This list can get truncated due to too many addresses getting added.
Reorder the entries in a way that allows the most recently added values
to be maintained in the list and use better debug/error messages when
parsing the value.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Skip the end of long configuration lines that get truncated in
wpa_config_get_line(). Without this, the rest of the file was being
parsed as another line and that resulted in an unexpected error
message (wrong line number and wrong starting point).
In addition, increase the read buffer for network blocks from 256
to 2000 since p2p_client_list parameter can have long values. These
were supposed to truncated cleanly, but the unexpected processing of
the end of the file (which is now fixed in this commit) could cause
configuration file to be rejected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Commit 99fcd40409 added a call to update
search delay after failed authentication attempt. This change was
supposed to be only in p2p_supplicant.c for the successful case. The
extra call does not really do anything, but it's good to remove it to
avoid any confusion in the future.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, all station mode scan operations were either skipped or
delayed while any P2P operation was in progress. To make concurrent
operations easier to use, reduce this limitation by allowing a scan
operation to be completed in the middle of a p2p_find. In addition,
allow station mode association to be completed. When the station mode
operation is run to its completion (scan results not acted on,
connection to an AP completed, connection failed), resume the p2p_find
operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the p2p_find command is used without the delay parameter, a 500 ms
default search delay will now be used when any interface using the same
radio is in an concurrent operation. "p2p_find delay=0" can be used to
enforce the old behavior in such a case if needed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A new optional delay=<search delay in milliseconds> parameter can now be
used with p2p_find command to request an extra delay between search
iterations. This can be used, e.g., to make p2p_find friendlier to
concurrent operations by avoiding it from taking 100% of the radio
resources.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This EAP type uses a vendor specific expanded EAP header to encapsulate
EAP-TLS with a configuration where the EAP server does not authenticate
the EAP peer. In other words, this method includes only server
authentication. The peer is configured with only the ca_cert parameter
(similarly to other TLS-based EAP methods). This method can be used for
cases where the network provides free access to anyone, but use of RSN
with a securely derived unique PMK for each station is desired.
The expanded EAP header uses the hostapd/wpa_supplicant vendor
code 39068 and vendor type 1 to identify the UNAUTH-TLS method.
Signed-hostap: Jouni Malinen <j@w1.fi>
The WPA_AUTH_WPA and WPA_AUTH_WPA2 cases have already been rejected in
this function when execution comes here. In theory, support for
WPA-Enterprise could be added, but since that has not happened over the
years, there is no good reason to keep this dead code here.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit c9e08af24f removed the only user of
the special case MD5 use that would be allowed in FIPS mode in
tls_prf_sha1_md5(). Commit 271dbf1594
removed the file from the build, but left the implementation into the
repository. To clean things up even further, remove this functionality
completely since it is not expected to be needed for FIPS mode anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since we currently support only HS 2.0 networks with Interworking
network selection, do not indicate credential match unless the
network uses WPA2-Enterprise.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since we currently support only HS 2.0 networks with Interworking
network selection, enforce that WPA2-Enterprise/CCMP is used on the
AP instead of allowing any WPA-Enterprise combination.
Signed-hostap: Jouni Malinen <j@w1.fi>
Hotspot 2.0 allows only WPA2-Enterprise to be used, so other types of
networks must not be indicated as Hotspot 2.0 networks even if they
(incorrectly) advertise HS 2.0 support.
Signed-hostap: Jouni Malinen <j@w1.fi>
When there was no credential match, but an enabled network block matched
with a scan result, wpa_supplicant reconnected at the end of
interworking_select command even if "auto" parameter was not used. Fix
this by running the reconnect only if requested to automatically select
a network.
Signed-hostap: Jouni Malinen <j@w1.fi>
If bgscan is enabled, then bgscan is initiated after the connection,
with no bss scan result information. Since a scan was performed prior to
the connection, the information exists and can be used to initialize the
bgscan's cache.
Signed-hostap: Yoni Divinsky <yoni.divinsky@ti.com>
When CONFIG_FIPS=y is used, do not include MD5 in the build and disable
EAPOL-Key frames that use MD5 (WPA/TKIP and dynamic WEP with IEEE
802.1X).
Signed-hostap: Jouni Malinen <j@w1.fi>
Only allow the TLS library keying material exporter functionality to be
used for MSK derivation with TLS-based EAP methods to avoid exporting
internal TLS keys from the library.
Signed-hostap: Jouni Malinen <j@w1.fi>
OpenSSL-based builds may need libdl in the linker line after the OpenSSL
library. CONFIG_TLS_ADD_DL=y can now be used to force that if needed.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used for convenience to build wpa_supplicant with OpenSSL
FIPS object module. CONFIG_FIPS=y is expected to be used in
wpa_supplicant/.config when using this option.
Signed-hostap: Jouni Malinen <j@w1.fi>
Increase GO config timeout if HT40 is used since it takes some time
to scan channels for coex purposes before the BSS can be started.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add optional "ht40" argument for p2p_group_add command to enable 40 MHz
in 5GHz band. This configures the secondary channel, when HT support is
enabled and if the HW supports 40 MHz channel width.
Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
These helper functions can be used to implement most of the common
wpa_cli commands to simplify the implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
If key_mgmt was set to allow both WPA and non-WPA IEEE 802.1X (i.e., to
IEEE8021X WPA-EAP), non-WPA IEEE 802.1X was rejected while preparing
association parameters. Allow this special case to be handled by
selecting non-WPA case if the scan results for the AP do not include
either WPA or RSN elements.
Signed-hostap: Jouni Malinen <j@w1.fi>
Refactoring done in commit 46ee0427b1
(IEEE 802.11u: Allow Interworking and HESSID to be configured)
broke adding extra IEs in sched scan. The IEs stopped being added
to the scan params within wpa_supplicant_extra_ies() but no code
was added to add them in wpa_supplicant_req_sched_scan().
Fix this and remove unused params arg in wpa_supplicant_extra_ies().
Signed-hostap: Eyal Shapira <eyal@wizery.com>
intended-for: hostap-1
GAS_QUERY_TIMEOUT value was used for two different things - enum for
status callback and #define for internal eloop timeout). The latter
overwrites the former and as such, the timeout reported ended up going
out with value 5 which matches with GAS_QUERY_CANCELLED instead of
GAS_QUERY_TIMEOUT. This value was not used in existing code, so this
should not modify the current behavior. Anyway, the correct reason for
the failure should be reported. Rename the internal #define for the
timeout period to avoid the name conflict. [Bug 463]
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need to mandate admission control (ACM=1) by default, so
clear that flag in the case the configuration file does not specify
wmm_ac_{vo,vi}_acm value. This gets closer to the values mentioned
in the sample hostapd.conf file and reduces the need to specify WMM
parameters in the configuration file for most common use cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
In case of P2P GO and AP mode, wpa_supplicant uses the default hostapd
parameters for WMM. In the default parameters the ACM bit for video and
voice are set to 1, meaning, P2P devices and stations which are
connected to the GO cannot pass voice or video data packets. Allow this
to be changed through wpa_supplicant configuration file with wmm_ac_*
parameters.
Signed-hostap: Yoni Divinsky <yoni.divinsky@ti.com>
The os_memcmp of bssid and wpa_s->bssid cannot return 0 in this
code path since identical os_memcmp was already done above.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is the normal flow for association:
wpa_supplicant <--(EVENT_ASSOC event )-- device driver
wpa_supplicant --( get_bssid() )--> device driver
wpa_supplicant <--( return BSSID )-- device driver
However, a device driver could return EINVAL for get_bssid() because it
recognizes it has already been disconnected. When the wpa_supplicant
received EINVAL, the bssid field could be used uninitialized in the
following flow:
wpa_supplicant <--(EVENT_ASSOC event )-- device driver
device driver (receive deauth)
wpa_supplicant --( get_bssid() )--> device driver
wpa_supplicant <--( return EINVAL )-- device driver
Prevent this by requiring the get_bssid() call to succeed when
processing association events.
Don't assume the 11g mode is always first in the list of mode (sometimes
it isn't). Traverse the array of modes and check the HT40 capability is
turned on for 11g.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
wpa_s->removal_reason was set only when calling wpas_p2p_group_delete()
and while couple of call places did not set this, it should really be
set in each case. As such, it works better as a function parameter than
a variable in struct wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
p2p_group_remove should only attempt to remove P2P group
interfaces and fail on non-P2P group interfaces.
Signed-hostap: Michael Naumov <michael.naumov@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
This enables setting a different max inactivity timeout for P2P GO.
This timeout is used to detect inactive clients. In some scenarios
it may be useful to have control over this and set a shorter timeout
than the default 300s. For example when running STA and P2P GO interfaces
concurrently, the STA interface may perform scans which may cause the
GO to miss a disassoc / deauth frames from a client and keep assuming
that the client is connected until the inactivity detection kicks in.
300 secs is a bit too long for such scenarios and creates a bad user
experience.
Signed-hostap: Eyal Shapira <eyal@wizery.com>
This simplifies the implementation by using the buffer type to which the
returned data will be converted anyway. This avoids one memory
allocation for each processed RADIUS message.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new ssid2 parameter can be used as an alternative mechanism for
configuring SSID for hostapd. It uses the same formats that
wpa_supplicant uses in the configuration file for strings.
Signed-hostap: Jouni Malinen <j@w1.fi>
P"<escaped string>" can now be used as an alternative method for
specifying non-ASCII strings (including control characters). For
example, ssid=P"abc\x00test".
Signed-hostap: Jouni Malinen <j@w1.fi>
Process CTRL-EVENT-TERMINATING in wpa_cli interactive mode and close
ctrl_iface connection without trying to detach the monitor interface
when this happens. This avoids a timeout on the DETACH command. In
addition, print out connection lost/re-established messages without
overriding the edit line.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is needed to allow the default behavior (pick first interface) to
be used in cases where wpa_supplicant is not available when wpa_cli is
started in interactive mode.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_ctrl_get_remote_ifname() is defined only for UDP ctrl_iface socket,
so this call needs to be made conditional on build parameters.
Signed-hostap: Jouni Malinen <j@w1.fi>
This changes the call flow to allow full eloop operations to be used
while waiting for wpa_cli to establish a connection to wpa_supplicant in
the beginning of an interactive session. This allows the cleanup steps
to be more consistent and avoid debugging issues due to unfreed memory
or other resources if wpa_cli is killed with Ctrl-c.
Signed-hostap: Jouni Malinen <j@w1.fi>
When starting interactive mode, wpa_cli is trying to attach the
monitor connection. If that fails, the operation is retried, but
this was done without freeing all the resources that could have
been allocated (mainly, the command connection).
Signed-hostap: Jouni Malinen <j@w1.fi>
When CONFIG_CTRL_IFACE=udp-remote is used, print user frendly PS in
wpa_cli. E.g.,
localhost/wlan0>
192.168.1.1/p2p-wlan-0-0>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Add new option for ctrl iface: CONFIG_CTRL_IFACE=udp-remote. This
enables remote access to control interface via UDP port(s). This should
be used for testing purpose only since there is no authentication or
access control on the commands.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The network_object path should be returned by the NetworkAdded signal
and not by the GroupStarted Signal. Starting a Group does not
necessarily validate the network object.
Signed-hostap: Michael Naumov <michael.naumov@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
intended-for: hostap-1
D-Bus script using python glib is added to perform Disconnect on an
interface.
Signed-hostap: Michael Naumov <michael.naumov@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
D-Bus script using python glib is added to perform p2p_invite on a group
interface to invite a peer.
Signed-hostap: Michael Naumov <michael.naumov@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
