DGNum/hostapd
6
0
Fork 0
Code Issues Pull requests 1 Projects Releases Packages Wiki Activity Actions
hostapd/src/common/qca-vendor.h
vamsi krishna 2800ec85d2 MBO: Add QCA vendor option to configure driver to ignore assoc disallow 
MBO capable APs can set association disallowed in the Beacon/Probe
Response frames. For testing purposes, the STA needs to be configured to
not ignore the association disallowed set by APs and continue to connect
to such AP like non-MBO enabled STA. Add a QCA vendor attribute for
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION vendor sub command to
configure the driver to ignore association disallowed functionality.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-09-25 17:31:26 +03:00

1568 lines
66 KiB
C
Raw Blame History

/*
* Qualcomm Atheros OUI and vendor specific assignments
* Copyright (c) 2014-2015, Qualcomm Atheros, Inc.
*
* This software may be distributed under the terms of the BSD license.
* See README for more details.
*/
#ifndef QCA_VENDOR_H
#define QCA_VENDOR_H
/*
* This file is a registry of identifier assignments from the Qualcomm Atheros
* OUI 00:13:74 for purposes other than MAC address assignment. New identifiers
* can be assigned through normal review process for changes to the upstream
* hostap.git repository.
*/
#define OUI_QCA 0x001374
/**
* enum qca_radiotap_vendor_ids - QCA radiotap vendor namespace IDs
*/
enum qca_radiotap_vendor_ids {
QCA_RADIOTAP_VID_WLANTEST = 0,
};
/**
* enum qca_nl80211_vendor_subcmds - QCA nl80211 vendor command identifiers
*
* @QCA_NL80211_VENDOR_SUBCMD_UNSPEC: Reserved value 0
*
* @QCA_NL80211_VENDOR_SUBCMD_TEST: Test command/event
*
* @QCA_NL80211_VENDOR_SUBCMD_ROAMING: Set roaming policy for drivers that use
* internal BSS-selection. This command uses
* @QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY to specify the new roaming policy
* for the current connection (i.e., changes policy set by the nl80211
* Connect command). @QCA_WLAN_VENDOR_ATTR_MAC_ADDR may optionally be
* included to indicate which BSS to use in case roaming is disabled.
*
* @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY: Recommendation of frequency
* ranges to avoid to reduce issues due to interference or internal
* co-existence information in the driver. The event data structure is
* defined in struct qca_avoid_freq_list.
*
* @QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY: Command to check driver support
* for DFS offloading.
*
* @QCA_NL80211_VENDOR_SUBCMD_NAN: NAN command/event which is used to pass
* NAN Request/Response and NAN Indication messages. These messages are
* interpreted between the framework and the firmware component.
*
* @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY: Set key operation that can be
* used to configure PMK to the driver even when not connected. This can
* be used to request offloading of key management operations. Only used
* if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD.
*
* @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH: An extended version of
* NL80211_CMD_ROAM event with optional attributes including information
* from offloaded key management operation. Uses
* enum qca_wlan_vendor_attr_roam_auth attributes. Only used
* if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD.
*
* @QCA_NL80211_VENDOR_SUBCMD_DO_ACS: ACS command/event which is used to
* invoke the ACS function in device and pass selected channels to
* hostapd.
*
* @QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES: Command to get the features
* supported by the driver. enum qca_wlan_vendor_features defines
* the possible features.
*
* @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED: Event used by driver,
* which supports DFS offloading, to indicate a channel availability check
* start.
*
* @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED: Event used by driver,
* which supports DFS offloading, to indicate a channel availability check
* completion.
*
* @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED: Event used by driver,
* which supports DFS offloading, to indicate that the channel availability
* check aborted, no change to the channel status.
*
* @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED: Event used by
* driver, which supports DFS offloading, to indicate that the
* Non-Occupancy Period for this channel is over, channel becomes usable.
*
* @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED: Event used by driver,
* which supports DFS offloading, to indicate a radar pattern has been
* detected. The channel is now unusable.
*
* @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to
* start the P2P Listen offload function in device and pass the listen
* channel, period, interval, count, device types, and vendor specific
* information elements to the device driver and firmware.
* Uses the attributes defines in
* enum qca_wlan_vendor_attr_p2p_listen_offload.
*
* @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP: Command/event used to
* indicate stop request/response of the P2P Listen offload function in
* device. As an event, it indicates either the feature stopped after it
* was already running or feature has actually failed to start. Uses the
* attributes defines in enum qca_wlan_vendor_attr_p2p_listen_offload.
*
* @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After AP starts
* beaconing, this sub command provides the driver, the frequencies on the
* 5 GHz band to check for any radar activity. Driver selects one channel
* from this priority list provided through
* @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts
* to check for radar activity on it. If no radar activity is detected
* during the channel availability check period, driver internally switches
* to the selected frequency of operation. If the frequency is zero, driver
* internally selects a channel. The status of this conditional switch is
* indicated through an event using the same sub command through
* @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are
* listed in qca_wlan_vendor_attr_sap_conditional_chan_switch.
*
* @QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND: Set GPIO pins. This uses the
* attributes defined in enum qca_wlan_gpio_attr.
*
* @QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY: Fetch hardware capabilities.
* This uses @QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY to indicate which
* capabilities are to be fetched and other
* enum qca_wlan_vendor_attr_get_hw_capability attributes to return the
* requested capabilities.
*
* @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Link layer statistics extension.
* enum qca_wlan_vendor_attr_ll_stats_ext attributes are used with this
* command and event.
*
* @QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA: Get capabilities for
* indoor location features. Capabilities are reported in
* QCA_WLAN_VENDOR_ATTR_LOC_CAPA.
*
* @QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION: Start an FTM
* (fine timing measurement) session with one or more peers.
* Specify Session cookie in QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE and
* peer information in QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS.
* On success, 0 or more QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT
* events will be reported, followed by
* QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE event to indicate
* end of session.
* Refer to IEEE P802.11-REVmc/D7.0, 11.24.6
*
* @QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION: Abort a running session.
* A QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE will be reported with
* status code indicating session was aborted.
*
* @QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT: Event with measurement
* results for one peer. Results are reported in
* QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS.
*
* @QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE: Event triggered when
* FTM session is finished, either successfully or aborted by
* request.
*
* @QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER: Configure FTM responder
* mode. QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE specifies whether
* to enable or disable the responder. LCI/LCR reports can be
* configured with QCA_WLAN_VENDOR_ATTR_FTM_LCI and
* QCA_WLAN_VENDOR_ATTR_FTM_LCR. Can be called multiple
* times to update the LCI/LCR reports.
*
* @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS: Perform a standalone AOA (angle of
* arrival) measurement with a single peer. Specify peer MAC address in
* QCA_WLAN_VENDOR_ATTR_MAC_ADDR and measurement type in
* QCA_WLAN_VENDOR_ATTR_AOA_TYPE. Measurement result is reported in
* QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT event.
*
* @QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS: Abort an AOA measurement. Specify
* peer MAC address in QCA_WLAN_VENDOR_ATTR_MAC_ADDR.
*
* @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT: Event that reports
* the AOA measurement result.
* Peer MAC address reported in QCA_WLAN_VENDOR_ATTR_MAC_ADDR.
* success/failure status is reported in
* QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS.
* Measurement data is reported in QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT.
* The antenna array(s) used in the measurement are reported in
* QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK.
*
* @QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST: Encrypt/decrypt the given
* data as per the given parameters.
*/
enum qca_nl80211_vendor_subcmds {
QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0,
QCA_NL80211_VENDOR_SUBCMD_TEST = 1,
/* subcmds 2..8 not yet allocated */
QCA_NL80211_VENDOR_SUBCMD_ROAMING = 9,
QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY = 10,
QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY = 11,
QCA_NL80211_VENDOR_SUBCMD_NAN = 12,
QCA_NL80211_VENDOR_SUBMCD_STATS_EXT = 13,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET = 14,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET = 15,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR = 16,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS = 17,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS = 18,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS = 19,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_START = 20,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_STOP = 21,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS = 22,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CAPABILITIES = 23,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS = 24,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE = 25,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT = 26,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT = 27,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND = 28,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_BSSID_HOTLIST = 29,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_BSSID_HOTLIST = 30,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE = 31,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SIGNIFICANT_CHANGE = 32,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SIGNIFICANT_CHANGE = 33,
QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE = 34,
QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE = 35,
QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS = 36,
QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE = 37,
QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES = 38,
QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI = 39,
QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG = 40,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_LOST = 41,
QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX = 42,
/* 43..49 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY = 50,
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH = 51,
QCA_NL80211_VENDOR_SUBCMD_APFIND = 52,
/* 53 - reserved - was used by QCA, but not in use anymore */
QCA_NL80211_VENDOR_SUBCMD_DO_ACS = 54,
QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES = 55,
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED = 56,
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED = 57,
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED = 58,
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED = 59,
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED = 60,
/* 61-73 - reserved for QCA */
/* Wi-Fi configuration subcommands */
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION = 74,
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION = 75,
/* 76-90 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_DATA_OFFLOAD = 91,
QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG = 92,
QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME = 93,
QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT = 94,
QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT = 95,
QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER = 96,
QCA_NL80211_VENDOR_SUBCMD_DCC_GET_STATS = 97,
QCA_NL80211_VENDOR_SUBCMD_DCC_CLEAR_STATS = 98,
QCA_NL80211_VENDOR_SUBCMD_DCC_UPDATE_NDL = 99,
QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT = 100,
QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES = 101,
QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG = 102,
QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST = 103,
QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL = 104,
QCA_NL80211_VENDOR_SUBCMD_SETBAND = 105,
QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN = 106,
QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE = 107,
QCA_NL80211_VENDOR_SUBCMD_OTA_TEST = 108,
QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE = 109,
/* 110..114 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB = 115,
/* 116..117 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG = 118,
QCA_NL80211_VENDOR_SUBCMD_TSF = 119,
QCA_NL80211_VENDOR_SUBCMD_WISA = 120,
/* 121 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START = 122,
QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123,
QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124,
QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND = 125,
QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY = 126,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT = 127,
/* FTM/indoor location subcommands */
QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA = 128,
QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION = 129,
QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION = 130,
QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT = 131,
QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE = 132,
QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER = 133,
QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS = 134,
QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS = 135,
QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT = 136,
QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST = 137,
};
enum qca_wlan_vendor_attr {
QCA_WLAN_VENDOR_ATTR_INVALID = 0,
/* used by QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY */
QCA_WLAN_VENDOR_ATTR_DFS = 1,
/* used by QCA_NL80211_VENDOR_SUBCMD_NAN */
QCA_WLAN_VENDOR_ATTR_NAN = 2,
/* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */
QCA_WLAN_VENDOR_ATTR_STATS_EXT = 3,
/* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */
QCA_WLAN_VENDOR_ATTR_IFINDEX = 4,
/* used by QCA_NL80211_VENDOR_SUBCMD_ROAMING, u32 with values defined
* by enum qca_roaming_policy. */
QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY = 5,
QCA_WLAN_VENDOR_ATTR_MAC_ADDR = 6,
/* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */
QCA_WLAN_VENDOR_ATTR_FEATURE_FLAGS = 7,
QCA_WLAN_VENDOR_ATTR_TEST = 8,
/* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */
/* Unsigned 32-bit value. */
QCA_WLAN_VENDOR_ATTR_CONCURRENCY_CAPA = 9,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_2_4_BAND = 10,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_5_0_BAND = 11,
/* Unsigned 32-bit value from enum qca_set_band. */
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE = 12,
/* Dummy (NOP) attribute for 64 bit padding */
QCA_WLAN_VENDOR_ATTR_PAD = 13,
/* Unique FTM session cookie (Unsigned 64 bit). Specified in
* QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION. Reported in
* the session in QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT and
* QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE.
*/
QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE = 14,
/* Indoor location capabilities, returned by
* QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA.
* see enum qca_wlan_vendor_attr_loc_capa.
*/
QCA_WLAN_VENDOR_ATTR_LOC_CAPA = 15,
/* Array of nested attributes containing information about each peer
* in FTM measurement session. See enum qca_wlan_vendor_attr_peer_info
* for supported attributes for each peer.
*/
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS = 16,
/* Array of nested attributes containing measurement results for
* one or more peers, reported by the
* QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT event.
* See enum qca_wlan_vendor_attr_peer_result for list of supported
* attributes.
*/
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS = 17,
/* Flag attribute for enabling or disabling responder functionality. */
QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE = 18,
/* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
* command to specify the LCI report that will be sent by
* the responder during a measurement exchange. The format is
* defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.10.
*/
QCA_WLAN_VENDOR_ATTR_FTM_LCI = 19,
/* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
* command to specify the location civic report that will
* be sent by the responder during a measurement exchange.
* The format is defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.13.
*/
QCA_WLAN_VENDOR_ATTR_FTM_LCR = 20,
/* Session/measurement completion status code,
* reported in QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE and
* QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT
* see enum qca_vendor_attr_loc_session_status.
*/
QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS = 21,
/* Initial dialog token used by responder (0 if not specified),
* unsigned 8 bit value.
*/
QCA_WLAN_VENDOR_ATTR_FTM_INITIAL_TOKEN = 22,
/* AOA measurement type. Requested in QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS
* and optionally in QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION if
* AOA measurements are needed as part of an FTM session.
* Reported by QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT. See
* enum qca_wlan_vendor_attr_aoa_type.
*/
QCA_WLAN_VENDOR_ATTR_AOA_TYPE = 23,
/* A bit mask (unsigned 32 bit value) of antenna arrays used
* by indoor location measurements. Refers to the antenna
* arrays described by QCA_VENDOR_ATTR_LOC_CAPA_ANTENNA_ARRAYS.
*/
QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK = 24,
/* AOA measurement data. Its contents depends on the AOA measurement
* type and antenna array mask:
* QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: array of U16 values,
* phase of the strongest CIR path for each antenna in the measured
* array(s).
* QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: array of 2 U16
* values, phase and amplitude of the strongest CIR path for each
* antenna in the measured array(s).
*/
QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT = 25,
/* keep last */
QCA_WLAN_VENDOR_ATTR_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_MAX = QCA_WLAN_VENDOR_ATTR_AFTER_LAST - 1,
};
enum qca_roaming_policy {
QCA_ROAMING_NOT_ALLOWED,
QCA_ROAMING_ALLOWED_WITHIN_ESS,
};
enum qca_wlan_vendor_attr_roam_auth {
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS,
/* keep last */
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MAX =
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST - 1
};
enum qca_wlan_vendor_attr_p2p_listen_offload {
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID = 0,
/* A 32-bit unsigned value; the P2P listen frequency (MHz); must be one
* of the social channels.
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL,
/* A 32-bit unsigned value; the P2P listen offload period (ms).
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD,
/* A 32-bit unsigned value; the P2P listen interval duration (ms).
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL,
/* A 32-bit unsigned value; number of interval times the firmware needs
* to run the offloaded P2P listen operation before it stops.
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT,
/* An array of arbitrary binary data with one or more 8-byte values.
* The device types include both primary and secondary device types.
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES,
/* An array of unsigned 8-bit characters; vendor information elements.
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE,
/* A 32-bit unsigned value; a control flag to indicate whether listen
* results need to be flushed to wpa_supplicant.
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG,
/* A 8-bit unsigned value; reason code for P2P listen offload stop
* event.
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON,
/* keep last */
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX =
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST - 1
};
enum qca_wlan_vendor_attr_acs_offload {
QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL,
QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL,
QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE,
QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED,
QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED,
QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED,
QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH,
QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST,
QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL,
QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL,
QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST,
/* keep last */
QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_ACS_MAX =
QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST - 1
};
enum qca_wlan_vendor_acs_hw_mode {
QCA_ACS_MODE_IEEE80211B,
QCA_ACS_MODE_IEEE80211G,
QCA_ACS_MODE_IEEE80211A,
QCA_ACS_MODE_IEEE80211AD,
QCA_ACS_MODE_IEEE80211ANY,
};
/**
* enum qca_wlan_vendor_features - Vendor device/driver feature flags
*
* @QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD: Device supports key
* management offload, a mechanism where the station's firmware
* does the exchange with the AP to establish the temporal keys
* after roaming, rather than having the user space wpa_supplicant do it.
* @QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY: Device supports automatic
* band selection based on channel selection results.
* @QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS: Device supports
* simultaneous off-channel operations.
* @QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD: Device supports P2P
* Listen offload; a mechanism where the station's firmware takes care of
* responding to incoming Probe Request frames received from other P2P
* Devices whilst in Listen state, rather than having the user space
* wpa_supplicant do it. Information from received P2P requests are
* forwarded from firmware to host whenever the host processor wakes up.
* @NUM_QCA_WLAN_VENDOR_FEATURES: Number of assigned feature bits
*/
enum qca_wlan_vendor_features {
QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD = 0,
QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY = 1,
QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS = 2,
QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD = 3,
NUM_QCA_WLAN_VENDOR_FEATURES /* keep last */
};
/**
* enum qca_wlan_vendor_attr_data_offload_ind - Vendor Data Offload Indication
*
* @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION: Session corresponding to
* the offloaded data.
* @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL: Protocol of the offloaded
* data.
* @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT: Event type for the data offload
* indication.
*/
enum qca_wlan_vendor_attr_data_offload_ind {
QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION,
QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL,
QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT,
/* keep last */
QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_MAX =
QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST - 1
};
enum qca_vendor_attr_get_preferred_freq_list {
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID,
/* A 32-unsigned value; the interface type/mode for which the preferred
* frequency list is requested (see enum qca_iface_type for possible
* values); used in GET_PREFERRED_FREQ_LIST command from user-space to
* kernel and in the kernel response back to user-space.
*/
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE,
/* An array of 32-unsigned values; values are frequency (MHz); sent
* from kernel space to user space.
*/
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST,
/* keep last */
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX =
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST - 1
};
enum qca_vendor_attr_probable_oper_channel {
QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID,
/* 32-bit unsigned value; indicates the connection/iface type likely to
* come on this channel (see enum qca_iface_type).
*/
QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE,
/* 32-bit unsigned value; the frequency (MHz) of the probable channel */
QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ,
/* keep last */
QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX =
QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST - 1
};
enum qca_iface_type {
QCA_IFACE_TYPE_STA,
QCA_IFACE_TYPE_AP,
QCA_IFACE_TYPE_P2P_CLIENT,
QCA_IFACE_TYPE_P2P_GO,
QCA_IFACE_TYPE_IBSS,
QCA_IFACE_TYPE_TDLS,
};
enum qca_set_band {
QCA_SETBAND_AUTO,
QCA_SETBAND_5G,
QCA_SETBAND_2G,
};
/**
* enum qca_access_policy - Access control policy
*
* Access control policy is applied on the configured IE
* (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE).
* To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY.
*
* @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi connections which match
* the specific configuration (IE) set, i.e., allow all the
* connections which do not match the configuration.
* @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi connections which match
* the specific configuration (IE) set, i.e., deny all the
* connections which do not match the configuration.
*/
enum qca_access_policy {
QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED,
QCA_ACCESS_POLICY_DENY_UNLESS_LISTED,
};
/**
* enum qca_vendor_attr_get_tsf: Vendor attributes for TSF capture
* @QCA_WLAN_VENDOR_ATTR_TSF_CMD: enum qca_tsf_operation (u32)
* @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Unsigned 64 bit TSF timer value
* @QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE: Unsigned 64 bit Synchronized
* SOC timer value at TSF capture
*/
enum qca_vendor_attr_tsf_cmd {
QCA_WLAN_VENDOR_ATTR_TSF_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_TSF_CMD,
QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE,
QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE,
QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_TSF_MAX =
QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST - 1
};
/**
* enum qca_tsf_operation: TSF driver commands
* @QCA_TSF_CAPTURE: Initiate TSF Capture
* @QCA_TSF_GET: Get TSF capture value
* @QCA_TSF_SYNC_GET: Initiate TSF capture and return with captured value
*/
enum qca_tsf_cmd {
QCA_TSF_CAPTURE,
QCA_TSF_GET,
QCA_TSF_SYNC_GET,
};
/**
* enum qca_vendor_attr_wisa_cmd
* @QCA_WLAN_VENDOR_ATTR_WISA_MODE: WISA mode value (u32)
* WISA setup vendor commands
*/
enum qca_vendor_attr_wisa_cmd {
QCA_WLAN_VENDOR_ATTR_WISA_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_WISA_MODE,
QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_WISA_MAX =
QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST - 1
};
/* IEEE 802.11 Vendor Specific elements */
/**
* enum qca_vendor_element_id - QCA Vendor Specific element types
*
* These values are used to identify QCA Vendor Specific elements. The
* payload of the element starts with the three octet OUI (OUI_QCA) and
* is followed by a single octet type which is defined by this enum.
*
* @QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST: P2P preferred channel list.
* This element can be used to specify preference order for supported
* channels. The channels in this list are in preference order (the first
* one has the highest preference) and are described as a pair of
* (global) Operating Class and Channel Number (each one octet) fields.
*
* This extends the standard P2P functionality by providing option to have
* more than one preferred operating channel. When this element is present,
* it replaces the preference indicated in the Operating Channel attribute.
* For supporting other implementations, the Operating Channel attribute is
* expected to be used with the highest preference channel. Similarly, all
* the channels included in this Preferred channel list element are
* expected to be included in the Channel List attribute.
*
* This vendor element may be included in GO Negotiation Request, P2P
* Invitation Request, and Provision Discovery Request frames.
*
* @QCA_VENDOR_ELEM_HE_CAPAB: HE Capabilities element.
* This element can be used for pre-standard publication testing of HE
* before P802.11ax draft assigns the element ID. The payload of this
* vendor specific element is defined by the latest P802.11ax draft.
* Please note that the draft is still work in progress and this element
* payload is subject to change.
*
* @QCA_VENDOR_ELEM_HE_OPER: HE Operation element.
* This element can be used for pre-standard publication testing of HE
* before P802.11ax draft assigns the element ID. The payload of this
* vendor specific element is defined by the latest P802.11ax draft.
* Please note that the draft is still work in progress and this element
* payload is subject to change.
*/
enum qca_vendor_element_id {
QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0,
QCA_VENDOR_ELEM_HE_CAPAB = 1,
QCA_VENDOR_ELEM_HE_OPER = 2,
};
/**
* enum qca_wlan_vendor_attr_scan - Specifies vendor scan attributes
*
* @QCA_WLAN_VENDOR_ATTR_SCAN_IE: IEs that should be included as part of scan
* @QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES: Nested unsigned 32-bit attributes
* with frequencies to be scanned (in MHz)
* @QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS: Nested attribute with SSIDs to be scanned
* @QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES: Nested array attribute of supported
* rates to be included
* @QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE: flag used to send probe requests
* at non CCK rate in 2GHz band
* @QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS: Unsigned 32-bit scan flags
* @QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE: Unsigned 64-bit cookie provided by the
* driver for the specific scan request
* @QCA_WLAN_VENDOR_ATTR_SCAN_STATUS: Unsigned 8-bit status of the scan
* request decoded as in enum scan_status
* @QCA_WLAN_VENDOR_ATTR_SCAN_MAC: 6-byte MAC address to use when randomisation
* scan flag is set
* @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with
* randomisation
*/
enum qca_wlan_vendor_attr_scan {
QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0,
QCA_WLAN_VENDOR_ATTR_SCAN_IE,
QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES,
QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS,
QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES,
QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE,
QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS,
QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE,
QCA_WLAN_VENDOR_ATTR_SCAN_STATUS,
QCA_WLAN_VENDOR_ATTR_SCAN_MAC,
QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK,
QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SCAN_MAX =
QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1
};
/**
* enum scan_status - Specifies the valid values the vendor scan attribute
* QCA_WLAN_VENDOR_ATTR_SCAN_STATUS can take
*
* @VENDOR_SCAN_STATUS_NEW_RESULTS: implies the vendor scan is successful with
* new scan results
* @VENDOR_SCAN_STATUS_ABORTED: implies the vendor scan was aborted in-between
*/
enum scan_status {
VENDOR_SCAN_STATUS_NEW_RESULTS,
VENDOR_SCAN_STATUS_ABORTED,
VENDOR_SCAN_STATUS_MAX,
};
/**
* enum qca_vendor_attr_ota_test - Specifies the values for vendor
* command QCA_NL80211_VENDOR_SUBCMD_OTA_TEST
* @QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE: enable ota test
*/
enum qca_vendor_attr_ota_test {
QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID,
/* 8-bit unsigned value to indicate if OTA test is enabled */
QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE,
/* keep last */
QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX =
QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST - 1
};
/**
* enum qca_vendor_attr_txpower_scale - vendor sub commands index
*
* @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE: scaling value
*/
enum qca_vendor_attr_txpower_scale {
QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID,
/* 8-bit unsigned value to indicate the scaling of tx power */
QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE,
/* keep last */
QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX =
QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST - 1
};
/**
* enum qca_vendor_attr_txpower_decr_db - Attributes for TX power decrease
*
* These attributes are used with QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB.
*/
enum qca_vendor_attr_txpower_decr_db {
QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_INVALID,
/* 8-bit unsigned value to indicate the reduction of TX power in dB for
* a virtual interface. */
QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB,
/* keep last */
QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_MAX =
QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST - 1
};
/* Attributes for data used by
* QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
* QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands.
*/
enum qca_wlan_vendor_attr_config {
QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID,
/* Unsigned 32-bit value to set the DTIM period.
* Whether the wifi chipset wakes at every dtim beacon or a multiple of
* the DTIM period. If DTIM is set to 3, the STA shall wake up every 3
* DTIM beacons.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM,
/* Unsigned 32-bit value to set the wifi_iface stats averaging factor
* used to calculate statistics like average the TSF offset or average
* number of frame leaked.
* For instance, upon Beacon frame reception:
* current_avg = ((beacon_TSF - TBTT) * factor + previous_avg * (0x10000 - factor) ) / 0x10000
* For instance, when evaluating leaky APs:
* current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR,
/* Unsigned 32-bit value to configure guard time, i.e., when
* implementing IEEE power management based on frame control PM bit, how
* long the driver waits before shutting down the radio and after
* receiving an ACK frame for a Data frame with PM bit set.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME,
/* Unsigned 32-bit value to change the FTM capability dynamically */
QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT,
/* Unsigned 16-bit value to configure maximum TX rate dynamically */
QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE,
/* Unsigned 32-bit value to configure the number of continuous
* Beacon Miss which shall be used by the firmware to penalize
* the RSSI.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS,
/* Unsigned 8-bit value to configure the channel avoidance indication
* behavior. Firmware to send only one indication and ignore duplicate
* indications when set to avoid multiple Apps wakeups.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND,
/* 8-bit unsigned value to configure the maximum TX MPDU for
* aggregation. */
QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION,
/* 8-bit unsigned value to configure the maximum RX MPDU for
* aggregation. */
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION,
/* 8-bit unsigned value to configure the Non aggregrate/11g sw
* retry threshold (0 disable, 31 max). */
QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY,
/* 8-bit unsigned value to configure the aggregrate sw
* retry threshold (0 disable, 31 max). */
QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY,
/* 8-bit unsigned value to configure the MGMT frame
* retry threshold (0 disable, 31 max). */
QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY,
/* 8-bit unsigned value to configure the CTRL frame
* retry threshold (0 disable, 31 max). */
QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY,
/* 8-bit unsigned value to configure the propagation delay for
* 2G/5G band (0~63, units in us) */
QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY,
/* Unsigned 32-bit value to configure the number of unicast TX fail
* packet count. The peer is disconnected once this threshold is
* reached. */
QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT,
/* Attribute used to set scan default IEs to the driver.
*
* These IEs can be used by scan operations that will be initiated by
* the driver/firmware.
*
* For further scan requests coming to the driver, these IEs should be
* merged with the IEs received along with scan request coming to the
* driver. If a particular IE is present in the scan default IEs but not
* present in the scan request, then that IE should be added to the IEs
* sent in the Probe Request frames for that scan request. */
QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES,
/* Unsigned 32-bit attribute for generic commands */
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND,
/* Unsigned 32-bit value attribute for generic commands */
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE,
/* Unsigned 32-bit data attribute for generic command response */
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA,
/* Unsigned 32-bit length attribute for
* QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH,
/* Unsigned 32-bit flags attribute for
* QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS,
/* Unsigned 32-bit, defining the access policy.
* See enum qca_access_policy. Used with
* QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. */
QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY,
/* Sets the list of full set of IEs for which a specific access policy
* has to be applied. Used along with
* QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access.
* Zero length payload can be used to clear this access constraint. */
QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST,
/* Unsigned 32-bit, specifies the interface index (netdev) for which the
* corresponding configurations are applied. If the interface index is
* not specified, the configurations are attributed to the respective
* wiphy. */
QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX,
/* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */
QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER,
/* 8-bit unsigned value to configure the driver and below layers to
* ignore the assoc disallowed set by APs while connecting
* 1-Ignore, 0-Don't ignore */
QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED,
/* keep last */
QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_CONFIG_MAX =
QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_sap_config - Parameters for AP configuration
*/
enum qca_wlan_vendor_attr_sap_config {
QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID = 0,
/* 1 - reserved for QCA */
/* List of frequencies on which AP is expected to operate.
* This is irrespective of ACS configuration. This list is a priority
* based one and is looked for before the AP is created to ensure the
* best concurrency sessions (avoid MCC and use DBS/SCC) co-exist in
* the system.
*/
QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST = 2,
QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX =
QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for AP
* conditional channel switch
*/
enum qca_wlan_vendor_attr_sap_conditional_chan_switch {
QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0,
/* Priority based frequency list (an array of u32 values in host byte
* order) */
QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1,
/* Status of the conditional switch (u32).
* 0: Success, Non-zero: Failure
*/
QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2,
QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX =
QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1,
};
/**
* enum qca_wlan_gpio_attr - Parameters for GPIO configuration
*/
enum qca_wlan_gpio_attr {
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0,
/* Unsigned 32-bit attribute for GPIO command */
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND,
/* Unsigned 32-bit attribute for GPIO PIN number to configure */
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM,
/* Unsigned 32-bit attribute for GPIO value to configure */
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE,
/* Unsigned 32-bit attribute for GPIO pull type */
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE,
/* Unsigned 32-bit attribute for GPIO interrupt mode */
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE,
/* keep last */
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST,
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX =
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1
};
/**
* enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability
*/
enum qca_wlan_vendor_attr_get_hw_capability {
QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID,
/* Antenna isolation
* An attribute used in the response.
* The content of this attribute is encoded in a byte array. Each byte
* value is an antenna isolation value. The array length is the number
* of antennas.
*/
QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION,
/* Request HW capability
* An attribute used in the request.
* The content of this attribute is a u32 array for one or more of
* hardware capabilities (attribute IDs) that are being requested. Each
* u32 value has a value from this
* enum qca_wlan_vendor_attr_get_hw_capability
* identifying which capabilities are requested.
*/
QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY,
/* keep last */
QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX =
QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring
* offload which is an extension for LL_STATS.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms.
* If MAC counters do not exceed the threshold, FW will report monitored
* link layer counters periodically as this setting. The first report is
* always triggered by this timer.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99).
* For each MAC layer counter, FW holds two copies. One is the current value.
* The other is the last report. Once a current counter's increment is larger
* than the threshold, FW will indicate that counter to host even if the
* monitoring timer does not expire.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same
* failure code.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code
* 1: TX packet discarded
* 2: No ACK
* 3: Postpone
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS: peer MAC address
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE: Peer STA current state
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL: Global threshold.
* Threshold for all monitored parameters. If per counter dedicated threshold
* is not enabled, this threshold will take effect.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE: Indicate what triggers this
* event, PERORID_TIMEOUT == 1, THRESH_EXCEED == 0.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID: interface ID
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID: peer ID
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP: bitmap for TX counters
* Bit0: TX counter unit in MSDU
* Bit1: TX counter unit in MPDU
* Bit2: TX counter unit in PPDU
* Bit3: TX counter unit in byte
* Bit4: Dropped MSDUs
* Bit5: Dropped Bytes
* Bit6: MPDU retry counter
* Bit7: MPDU failure counter
* Bit8: PPDU failure counter
* Bit9: MPDU aggregation counter
* Bit10: MCS counter for ACKed MPDUs
* Bit11: MCS counter for Failed MPDUs
* Bit12: TX Delay counter
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP: bitmap for RX counters
* Bit0: MAC RX counter unit in MPDU
* Bit1: MAC RX counter unit in byte
* Bit2: PHY RX counter unit in PPDU
* Bit3: PHY RX counter unit in byte
* Bit4: Disorder counter
* Bit5: Retry counter
* Bit6: Duplication counter
* Bit7: Discard counter
* Bit8: MPDU aggregation size counter
* Bit9: MCS counter
* Bit10: Peer STA power state change (wake to sleep) counter
* Bit11: Peer STA power save counter, total time in PS mode
* Bit12: Probe request counter
* Bit13: Other management frames counter
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP: bitmap for CCA
* Bit0: Idle time
* Bit1: TX time
* Bit2: time RX in current bss
* Bit3: Out of current bss time
* Bit4: Wireless medium busy time
* Bit5: RX in bad condition time
* Bit6: TX in bad condition time
* Bit7: time wlan card not available
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP: bitmap for signal
* Bit0: Per channel SNR counter
* Bit1: Per channel noise floor counter
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM: number of peers
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM: number of channels
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_AC_RX_NUM: number of RX stats
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS: per channel BSS CCA stats
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER: container for per PEER stats
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU: Number of total TX MSDUs
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU: Number of total TX MPDUs
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU: Number of total TX PPDUs
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES: bytes of TX data
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP: Number of dropped TX packets
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES: Bytes dropped
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY: waiting time without an ACK
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK: number of MPDU not-ACKed
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK: number of PPDU not-ACKed
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM:
* aggregation stats buffer length
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM: length of mcs stats
* buffer for ACKed MPDUs.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM: length of mcs stats
* buffer for failed MPDUs.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE:
* length of delay stats array.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR: TX aggregation stats
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS: MCS stats for ACKed MPDUs
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS: MCS stats for failed MPDUs
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY: tx delay stats
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU: MPDUs received
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES: bytes received
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU: PPDU received
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES: PPDU bytes received
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST: packets lost
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY: number of RX packets
* flagged as retransmissions
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP: number of RX packets
* flagged as duplicated
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD: number of RX
* packets discarded
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM: length of RX aggregation
* stats buffer.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM: length of RX mcs
* stats buffer.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS: RX mcs stats buffer
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR: aggregation stats buffer
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES: times STAs go to sleep
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION: STAs' total sleep time
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ: number of probe
* requests received
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT: number of other mgmt
* frames received
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME: Percentage of idle time
* there is no TX, nor RX, nor interference.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME: percentage of time
* transmitting packets.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME: percentage of time
* for receiving.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY: percentage of time
* interference detected.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD: percentage of time
* receiving packets with errors.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD: percentage of time
* TX no-ACK.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL: percentage of time
* the chip is unable to work in normal conditions.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME: percentage of time
* receiving packets in current BSS.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME: percentage of time
* receiving packets not in current BSS.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM: number of antennas
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL:
* This is a container for per antenna signal stats.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR: per antenna SNR value
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF: per antenna NF value
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON: RSSI of beacon
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON: SNR of beacon
*/
enum qca_wlan_vendor_attr_ll_stats_ext {
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0,
/* Attributes for configurations */
QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD,
QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD,
/* Peer STA power state change */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG,
/* TX failure event */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS,
/* MAC counters */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER,
/* Sub-attributes for PEER_AC_TX */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY,
/* Sub-attributes for PEER_AC_RX */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT,
/* Sub-attributes for CCA_BSS */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL,
/* sub-attribute for BSS_RX_TIME */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME,
/* Sub-attributes for PEER_SIGNAL */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF,
/* Sub-attributes for IFACE_BSS */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX =
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1
};
/* Attributes for FTM commands and events */
/**
* enum qca_wlan_vendor_attr_loc_capa - Indoor location capabilities
*
* @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS: Various flags. See
* enum qca_wlan_vendor_attr_loc_capa_flags.
* @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS: Maximum number
* of measurement sessions that can run concurrently.
* Default is one session (no session concurrency).
* @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS: The total number of unique
* peers that are supported in running sessions. For example,
* if the value is 8 and maximum number of sessions is 2, you can
* have one session with 8 unique peers, or 2 sessions with 4 unique
* peers each, and so on.
* @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP: Maximum number
* of bursts per peer, as an exponent (2^value). Default is 0,
* meaning no multi-burst support.
* @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST: Maximum number
* of measurement exchanges allowed in a single burst.
* @QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES: Supported AOA measurement
* types. A bit mask (unsigned 32 bit value), each bit corresponds
* to an AOA type as defined by enum qca_vendor_attr_aoa_type.
*/
enum qca_wlan_vendor_attr_loc_capa {
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_INVALID,
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS,
QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS,
QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS,
QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP,
QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST,
QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES,
/* keep last */
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_MAX =
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_loc_capa_flags: Indoor location capability flags
*
* @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER: Set if driver
* can be configured as an FTM responder (for example, an AP that
* services FTM requests). QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
* will be supported if set.
* @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR: Set if driver
* can run FTM sessions. QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION
* will be supported if set.
* @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP: Set if FTM responder
* supports immediate (ASAP) response.
* @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA: Set if driver supports standalone
* AOA measurement using QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS.
* @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM: Set if driver supports
* requesting AOA measurements as part of an FTM session.
*/
enum qca_wlan_vendor_attr_loc_capa_flags {
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER = 1 << 0,
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR = 1 << 1,
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP = 1 << 2,
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA = 1 << 3,
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM = 1 << 4,
};
/**
* enum qca_wlan_vendor_attr_ftm_peer_info: Information about
* a single peer in a measurement session.
*
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR: The MAC address of the peer.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS: Various flags related
* to measurement. See enum qca_wlan_vendor_attr_ftm_peer_meas_flags.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS: Nested attribute of
* FTM measurement parameters, as specified by IEEE P802.11-REVmc/D7.0
* 9.4.2.167. See enum qca_wlan_vendor_attr_ftm_meas_param for
* list of supported attributes.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID: Initial token ID for
* secure measurement.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD: Request AOA
* measurement every <value> bursts. If 0 or not specified,
* AOA measurements will be disabled for this peer.
*/
enum qca_wlan_vendor_attr_ftm_peer_info {
QCA_WLAN_VENDOR_ATTR_FTM_PEER_INVALID,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD,
/* keep last */
QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAX =
QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_ftm_peer_meas_flags: Measurement request flags,
* per-peer
*
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP: If set, request
* immediate (ASAP) response from peer.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI: If set, request
* LCI report from peer. The LCI report includes the absolute
* location of the peer in "official" coordinates (similar to GPS).
* See IEEE P802.11-REVmc/D7.0, 11.24.6.7 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR: If set, request
* Location civic report from peer. The LCR includes the location
* of the peer in free-form format. See IEEE P802.11-REVmc/D7.0,
* 11.24.6.7 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE: If set,
* request a secure measurement.
* QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID must also be provided.
*/
enum qca_wlan_vendor_attr_ftm_peer_meas_flags {
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP = 1 << 0,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI = 1 << 1,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR = 1 << 2,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE = 1 << 3,
};
/**
* enum qca_wlan_vendor_attr_ftm_meas_param: Measurement parameters
*
* @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST: Number of measurements
* to perform in a single burst.
* @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP: Number of bursts to
* perform, specified as an exponent (2^value).
* @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION: Duration of burst
* instance, as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167.
* @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD: Time between bursts,
* as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. Must
* be larger than QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION.
*/
enum qca_wlan_vendor_attr_ftm_meas_param {
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_INVALID,
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST,
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP,
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION,
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD,
/* keep last */
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MAX =
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_ftm_peer_result: Per-peer results
*
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR: MAC address of the reported
* peer.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS: Status of measurement
* request for this peer.
* See enum qca_wlan_vendor_attr_ftm_peer_result_status.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS: Various flags related
* to measurement results for this peer.
* See enum qca_wlan_vendor_attr_ftm_peer_result_flags.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS: Specified when
* request failed and peer requested not to send an additional request
* for this number of seconds.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI: LCI report when received
* from peer. In the format specified by IEEE P802.11-REVmc/D7.0,
* 9.4.2.22.10.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR: Location civic report when
* received from peer. In the format specified by IEEE P802.11-REVmc/D7.0,
* 9.4.2.22.13.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS: Reported when peer
* overridden some measurement request parameters. See
* enum qca_wlan_vendor_attr_ftm_meas_param.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS: AOA measurement
* for this peer. Same contents as @QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS: Array of measurement
* results. Each entry is a nested attribute defined
* by enum qca_wlan_vendor_attr_ftm_meas.
*/
enum qca_wlan_vendor_attr_ftm_peer_result {
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_INVALID,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS,
/* keep last */
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAX =
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_ftm_peer_result_status
*
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK: Request sent ok and results
* will be provided. Peer may have overridden some measurement parameters,
* in which case overridden parameters will be report by
* QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAM attribute.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE: Peer is incapable
* of performing the measurement request. No more results will be sent
* for this peer in this session.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED: Peer reported request
* failed, and requested not to send an additional request for number
* of seconds specified by QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS
* attribute.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID: Request validation
* failed. Request was not sent over the air.
*/
enum qca_wlan_vendor_attr_ftm_peer_result_status {
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID,
};
/**
* enum qca_wlan_vendor_attr_ftm_peer_result_flags: Various flags
* for measurement result, per-peer
*
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE: If set,
* measurement completed for this peer. No more results will be reported
* for this peer in this session.
*/
enum qca_wlan_vendor_attr_ftm_peer_result_flags {
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE = 1 << 0,
};
/**
* enum qca_vendor_attr_loc_session_status: Session completion status code
*
* @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK: Session completed
* successfully.
* @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED: Session aborted
* by request.
* @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID: Session request
* was invalid and was not started.
* @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED: Session had an error
* and did not complete normally (for example out of resources).
*/
enum qca_vendor_attr_loc_session_status {
QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK,
QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED,
QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID,
QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED,
};
/**
* enum qca_wlan_vendor_attr_ftm_meas: Single measurement data
*
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1: Time of departure (TOD) of FTM packet as
* recorded by responder, in picoseconds.
* See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2: Time of arrival (TOA) of FTM packet at
* initiator, in picoseconds.
* See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3: TOD of ACK packet as recorded by
* initiator, in picoseconds.
* See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4: TOA of ACK packet at
* responder, in picoseconds.
* See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI: RSSI (signal level) as recorded
* during this measurement exchange. Optional and will be provided if
* the hardware can measure it.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR: TOD error reported by
* responder. Not always provided.
* See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR: TOA error reported by
* responder. Not always provided.
* See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR: TOD error measured by
* initiator. Not always provided.
* See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR: TOA error measured by
* initiator. Not always provided.
* See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD: Dummy attribute for padding.
*/
enum qca_wlan_vendor_attr_ftm_meas {
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD,
/* keep last */
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_MAX =
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_aoa_type - AOA measurement type
*
* @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: Phase of the strongest
* CIR (channel impulse response) path for each antenna.
* @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: Phase and amplitude
* of the strongest CIR path for each antenna.
*/
enum qca_wlan_vendor_attr_aoa_type {
QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE,
QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP,
QCA_WLAN_VENDOR_ATTR_AOA_TYPE_MAX
};
/**
* enum qca_wlan_vendor_attr_encryption_test - Attributes to
* validate encryption engine
*
* @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION: Flag attribute.
* This will be included if the request is for decryption; if not included,
* the request is treated as a request for encryption by default.
* @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER: Unsigned 32-bit value
* indicating the key cipher suite. Takes same values as
* NL80211_ATTR_KEY_CIPHER.
* @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID: Unsigned 8-bit value
* Key Id to be used for encryption
* @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK: Array of 8-bit values.
* Key (TK) to be used for encryption/decryption
* @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN: Array of 8-bit values.
* Packet number to be specified for encryption/decryption
* 6 bytes for TKIP/CCMP/GCMP.
* @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA: Array of 8-bit values
* representing the 802.11 packet (header + payload + FCS) that
* needs to be encrypted/decrypted.
* Encrypted/decrypted response from the driver will also be sent
* to userspace with the same attribute.
*/
enum qca_wlan_vendor_attr_encryption_test {
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION,
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER,
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID,
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK,
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN,
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA,
/* keep last */
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_MAX =
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST - 1
};
#endif /* QCA_VENDOR_H */
Reference in a new issue View git blame Copy permalink