hostapd/tests/hwsim
Andrei Otcheretianski 53606b105c tests: Wait for scan to complete on all interfaces in reset()
When WpaSupplicant executes reset() it waits until all the ongoing scans
are completed. However, it checks the status of the wlanX interface
only. If a dedicated P2P device interface is used, scan may be still
running on the P2P Device interface, e.g., due to P2P_FIND. This might
affect subsequent tests.

Fix this by waiting until the scan is done both on wlanX and P2P
Device interfaces.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-07-08 16:52:42 +03:00
..
auth_serv tests: WPA2-Enterprise connection using MAC ACL 2015-07-01 00:34:27 +03:00
tnc tests: Use QUIET=1 option to make build.sh output much shorter 2014-12-29 15:49:05 +02:00
vm tests: Print a command line to re-run failed test sequence 2015-06-18 21:39:24 +03:00
bss-1.conf tests: Test dynamic BSS addition/removal 2013-10-31 23:04:50 +02:00
bss-2.conf tests: Test dynamic BSS addition/removal 2013-10-31 23:04:50 +02:00
bss-3.conf tests: Test dynamic BSS addition/removal 2013-10-31 23:04:50 +02:00
bss-ht40-1.conf tests: Verify BSS additional/removal during HT co-ex scan 2013-11-06 15:52:40 +02:00
bss-ht40-2.conf tests: Verify BSS additional/removal during HT co-ex scan 2013-11-06 15:52:40 +02:00
build.sh tests: Reorder build.sh operations 2014-12-29 15:49:05 +02:00
check_kernel.py hwsim tests: Check kernel messages for lockdep complaints 2013-11-20 16:39:24 +02:00
dictionary.radius tests: Verify dynamic_vlan=required is honored with macaddr_acl=2 2015-04-25 10:28:19 +03:00
example-hostapd.config tests: Add Undefined Behavior Sanitizer (ubsan) configuration 2015-07-07 18:23:04 +03:00
example-setup.txt tests: Document dependency on python-crypto 2015-03-07 23:47:02 +02:00
example-wpa_supplicant.config tests: Add Undefined Behavior Sanitizer (ubsan) configuration 2015-07-07 18:23:04 +03:00
hostapd.accept tests: Add test cases for AP VLAN 2014-03-08 11:35:08 +02:00
hostapd.macaddr tests: hostapd MAC ACL file entry removal 2014-03-30 17:06:34 +03:00
hostapd.py tests: Verify correct VLAN operation in multi-BSS multi-VLAN case 2015-06-14 13:40:50 +03:00
hostapd.vlan tests: VLAN using vlan_file mapping 2014-03-30 17:06:34 +03:00
hostapd.wlan3.vlan tests: Verify RSN preauth with dynamic VLANs 2015-04-13 17:08:10 +03:00
hostapd.wlan4.vlan tests: Verify RSN preauth with dynamic VLANs 2015-04-13 17:08:10 +03:00
hostapd.wpa_psk tests: Verify different ways of configuring passphrase/PSK 2014-02-04 13:10:57 +02:00
hwsim.py tests: Introduce hwsim radio context manager 2014-10-21 17:35:20 +03:00
hwsim_utils.py tests: Add test to check disconnect in powersave 2015-02-21 16:07:52 +02:00
multi-bss-acs.conf tests: Add test cases for automatic channel selection 2013-11-03 21:30:31 +02:00
multi-bss-iface.conf tests: Verify correct VLAN operation in multi-BSS multi-VLAN case 2015-06-14 13:40:50 +03:00
multi-bss.conf tests: Add test case for multi-BSS configuration file 2013-11-03 20:20:50 +02:00
netlink.py hwsim tests: Add support for the chanctx flag when creating radios 2014-02-25 16:53:40 +02:00
nl80211.py tests: cfg80211 DEL_STATION issued externally to hostapd 2015-01-29 16:26:31 +02:00
p2p0.conf tests: Add start/stop scripts and configuration files 2013-03-02 11:39:54 +02:00
p2p1.conf tests: Add start/stop scripts and configuration files 2013-03-02 11:39:54 +02:00
p2p2.conf tests: Add start/stop scripts and configuration files 2013-03-02 11:39:54 +02:00
radius_das.py tests: Remove unnecessary interpreter line from most python files 2014-02-21 20:21:53 +02:00
README tests: Add step-by-step guide for setting up test framework 2015-01-18 18:11:11 +02:00
rfkill.py tests: Add rfkill module 2015-01-08 20:56:47 +02:00
run-all.sh tests: Add usage() to run-all.sh 2014-11-01 17:08:29 +02:00
run-tests.py tests: Allow running with arbitrary working directory 2015-03-07 12:23:07 +02:00
start.sh tests: Valid OCSP response with revoked and unknown cert status 2015-01-12 00:19:21 +02:00
stop.sh tests: Optimize stop.sh wait times 2014-12-22 19:37:08 +02:00
test_ap_acs.py tests: Automatic channel selection with chanlist set 2015-05-24 10:43:44 +03:00
test_ap_ciphers.py tests: Group management frame cipher suites 2015-01-24 19:37:42 +02:00
test_ap_config.py tests: hostapd configuration file error cases 2014-03-29 10:36:25 +02:00
test_ap_csa.py tests: Convert test skipping to use exception 2015-01-08 22:43:47 +02:00
test_ap_dynamic.py tests: Make ap_remove_during_acs* more robust 2015-03-07 00:00:08 +02:00
test_ap_eap.py tests: EAP server and OOM 2015-07-01 00:42:09 +03:00
test_ap_ft.py tests: WPA2-PSK-FT AP over DS protocol testing 2015-07-07 16:25:06 +03:00
test_ap_hs20.py tests: Pending GAS query interrupted with deinit 2015-06-11 02:57:34 +03:00
test_ap_ht.py tests: HT40 co-ex scan conflict (HT40-) 2015-06-23 11:25:22 +03:00
test_ap_mixed.py tests: Make ap_mixed_security more robust 2015-01-18 12:50:20 +02:00
test_ap_open.py tests: Use the new CTRL-EVENT-NETWORK-NOT-FOUND in ap_open_select_any 2015-06-27 11:09:22 +03:00
test_ap_params.py tests: UPDATE_BEACON to change vendor_elements at runtime 2015-05-24 13:43:30 +03:00
test_ap_pmf.py tests: More WPA2-EAP + PMF test coverage 2015-06-06 17:13:21 +03:00
test_ap_psk.py tests: WPA2-PSK AP and no random numbers available 2015-06-29 23:23:56 +03:00
test_ap_qosmap.py tests: Convert test skipping to use exception 2015-01-08 22:43:47 +02:00
test_ap_roam.py tests: Add wait_connected() and wait_disconnected() helpers 2014-12-20 13:10:09 +02:00
test_ap_tdls.py tests: TDLS link status test 2015-05-03 17:24:38 +03:00
test_ap_vht.py tests: Use different channel offset for the second 160 MHz VHT AP 2015-06-23 02:42:17 +03:00
test_ap_vlan.py tests: Verify correct VLAN operation in multi-BSS multi-VLAN case 2015-06-14 13:40:50 +03:00
test_ap_wps.py tests: Increase HTTPConnection timeout in ap_wps_upnp_http_proto 2015-06-19 13:45:16 +03:00
test_autoscan.py tests: AUTOSCAN reconfiguration while in SCANNING state 2014-12-11 22:57:36 +02:00
test_bgscan.py tests: Additional bgscan coverage 2015-01-06 02:49:13 +02:00
test_cfg80211.py tests: cfg80211 DEL_STATION issued externally to hostapd 2015-01-29 16:26:31 +02:00
test_connect_cmd.py tests: bg_scan_period parameter configuration 2014-12-20 19:44:40 +02:00
test_dbus.py tests: D-Bus AddNetwork and connection with WPA+WPA2-Enterprise AP 2015-06-20 23:04:31 +03:00
test_dbus_old.py tests: Make dbus_old_wps_pbc more robust 2015-06-20 15:35:52 +03:00
test_dfs.py tests: Remove unnecessary use of sudo from test cases 2015-02-07 15:37:13 +02:00
test_eap_proto.py tests: Fix EAP-SIM/AKA protocol tests to use full header 2015-05-03 16:32:59 +03:00
test_erp.py tests: ERP with EAP-EKE 2015-05-24 12:01:25 +03:00
test_ext_password.py tests: EXT PW with no valid PSK found 2014-04-13 10:26:52 +03:00
test_gas.py tests: Check GAS and ANQP completion events in gas_fragment 2015-06-27 17:13:24 +03:00
test_hapd_ctrl.py tests: Use 16 instead of 13 as the cwmin/cwmax invalid case 2015-06-27 23:24:15 +03:00
test_hostapd_oom.py tests: hostapd OOM loop tests for WPA2-PSK and WPA2-EAP connection 2015-01-29 22:33:25 +02:00
test_ibss.py tests: IBSS on 5 GHz band 2015-06-14 19:35:19 +03:00
test_ieee8021x.py tests: IEEE 802.1X and HELD state 2015-07-07 19:25:31 +03:00
test_module_tests.py tests: Remove unnecessary interpreter line from most python files 2014-02-21 20:21:53 +02:00
test_monitor_interface.py tests: Stop connection at the end of monitor_iface_unknown_sta 2014-11-30 15:53:11 +02:00
test_nfc_p2p.py tests: NFC static handover with invalid contents 2015-06-19 01:23:24 +03:00
test_nfc_wps.py tests: Additional invalid NDEF records 2015-07-08 16:52:42 +03:00
test_offchannel_tx.py tests: Make offchannel_tx_roc_gas more robust 2015-03-06 17:03:06 +02:00
test_p2p_autogo.py tests: Fix autogo_pbc() waiting for WPS-PBC 2015-06-19 10:59:01 +03:00
test_p2p_channel.py tests: P2P GO and 5 GHz channels 165 (allowed) and 169 (disallowed) in US 2015-06-12 20:54:01 +03:00
test_p2p_concurrency.py tests: Concurrent P2P autonomous GO on 5 GHz and HT40 co-ex 2015-06-29 23:23:56 +03:00
test_p2p_device.py tests: Change p2p_device_nfc_invite to use global interface 2015-05-07 21:35:29 +03:00
test_p2p_discovery.py tests: Modify test_p2p_discovery to use global and group interfaces 2015-02-07 15:37:13 +02:00
test_p2p_ext.py tests: VENDOR_ELEM_ADD for various frames 2015-06-15 14:16:30 +03:00
test_p2p_grpform.py tests: Fix grpform_wait_peer group removal in P2P Device case 2015-06-19 11:28:20 +03:00
test_p2p_invitation.py tests: Update group ifname in p2p_go_invite_auth 2015-02-05 13:38:10 +02:00
test_p2p_messages.py tests: Change test_p2p_messages to use global interface 2015-05-07 21:11:03 +03:00
test_p2p_persistent.py tests: Use global interface for "P2P_SET" 2015-06-19 10:37:08 +03:00
test_p2p_service.py tests: Use global control interface in test_p2p_service 2015-02-05 13:48:40 +02:00
test_p2p_set.py tests: Fix p2p_set_discoverability waiting for CTRL-EVENT-CONNECTED 2015-06-19 11:27:15 +03:00
test_p2p_wifi_display.py tests: Fix wifi_display to use the global control interface 2015-06-19 11:14:30 +03:00
test_p2ps.py tests: P2PS with large number of services in Probe Request/Response 2015-06-18 18:14:04 +03:00
test_peerkey.py tests: PeerKey failure due to mismatching cipher 2014-04-05 17:52:44 +03:00
test_pmksa_cache.py tests: Verify RSN preauth with dynamic VLANs 2015-04-13 17:08:10 +03:00
test_radio_work.py tests: RADIO_WORK error cases 2014-12-12 00:27:06 +02:00
test_radius.py tests: More RADIUS testing coverage with CUI/User-Name in ACL response 2015-06-19 00:23:49 +03:00
test_rfkill.py tests: Convert test skipping to use exception 2015-01-08 22:43:47 +02:00
test_sae.py tests: SAE and no random numbers available 2015-06-29 23:23:56 +03:00
test_scan.py tests: Make ap_wps_ap_scan_2 more robust 2015-06-18 22:33:48 +03:00
test_ssid.py tests: Make hidden SSID test cases more robust 2014-11-28 23:02:29 +02:00
test_sta_dynamic.py tests: Remove unnecessary use of sudo from test cases 2015-02-07 15:37:13 +02:00
test_suite_b.py tests: Suite B with external RADIUS server 2015-06-20 23:04:31 +03:00
test_tnc.py tests: EAP-TNC fragmentation 2015-01-17 12:12:33 +02:00
test_wep.py tests: Add wait_connected() and wait_disconnected() helpers 2014-12-20 13:10:09 +02:00
test_wext.py tests: Close wlan5 control interface monitor more explicitly 2015-01-18 17:13:55 +02:00
test_wnm.py tests: WNM BSS Transition Management in different countries 2015-06-14 18:11:14 +03:00
test_wpas_ap.py tests: Verify wpa_supplicant AP mode events 2015-03-14 10:14:47 +02:00
test_wpas_config.py tests: wps_priority in configuration and WPS behavior 2015-06-04 14:04:16 +03:00
test_wpas_ctrl.py tests: Update wpas_ctrl_network to match removal of WEP as group cipher 2015-06-20 23:04:31 +03:00
test_wpas_mesh.py tests: Make wpas_mesh_password_mismatch more robust 2015-02-12 15:50:52 +02:00
test_wpas_wmm_ac.py tests: WMM-AC reassociation-to-same-BSS test 2015-01-04 18:59:07 +02:00
tshark.py tests: Add capture file validation for IPv4 in proxyarp_open 2015-01-30 18:55:22 +02:00
utils.py tests: WPA2-PSK AP and no random numbers available 2015-06-29 23:23:56 +03:00
w1fi_logo.png tests: HS 2.0 OSU and icon fetch 2014-03-02 10:35:34 +02:00
wlantest.py tests: Re-association to same BSS to toggle PMF status 2015-02-19 16:37:12 +02:00
wpasupplicant.py tests: Wait for scan to complete on all interfaces in reset() 2015-07-08 16:52:42 +03:00
wps-mixed-cred tests: WPS mixed-WPA/WPA2 credential merging 2014-08-29 20:25:18 +03:00
wps-wep-cred tests: WPS 2.0 rejection of WEP credential 2014-03-05 12:40:54 +02:00

Automated hostapd/wpa_supplicant testing with mac80211_hwsim
------------------------------------------------------------

This directory contains testing infrastructure and test cases to run
automated tests of full hostapd and wpa_supplicant functionality. This
testing is done with the help of mac80211_hwsim which is Linux kernel
driver that simulates IEEE 802.11 radios without requiring any
additional hardware. This setup most of the hostapd and wpa_supplicant
functionality (and large parts of the Linux cfg80211 and mac80211
functionality for that matter) to be tested.

mac80211_hwsim is loaded with five simulated radios to allow different
device combinations to be tested. wlantest is used analyze raw packets
captured through the hwsim0 monitor interface that capture all frames
sent on all channels. wlantest is used to store the frames for
analysis. Three wpa_supplicant processes are used to control three
virtual radios and one hostapd process is used to dynamically control
the other two virtual radios. wpa_supplicant/hostapd test functionality
is used to verify that data connection (both unicast and broadcast)
works between two netdevs.

The python scripts and tools in this directory control test case
execution. They interact wpa_supplicant and hostapd through control
interfaces to perform the operations. In addition, wlantest_cli is used
to verify that operations have been performed correctly and that the
network connection works in the expected way.

These test cases are run automatically against the hostap.git commits
for regression testing and to help in keeping the hostap.git master
branch in stable state. Results from these tests are available here:
http://buildbot.w1.fi/hwsim/


Building binaries for testing
-----------------------------

You will need to build (or use already built) components to be
tested. These are available in the hostap.git repository and can be
built for example as follows:

cd ../../wpa_supplicant
cp ../tests/hwsim/example-wpa_supplicant.config .config
make clean
make
cd ../hostapd
cp ../tests/hwsim/example-hostapd.config .config
make clean
make hostapd hlr_auc_gw
cd ../wlantest
make clean
make

Alternatively, the build.sh script here can be used to run these steps
with conditional creation of .config files only if they do not exist.

The test scripts can find the binaries in the locations where they were
built. It is also possible to install wlantest_cli somewhere on the path
to use pre-built tools.

Please note that some of the configuration parameters used to enable
more testing coverage may require development packages that may not be
installed by default in many distributions. For example, following
Debian/Ubuntu packages are likely to be needed:
- binutils-dev
- libsqlite3-dev
- libpcap-dev

example-setup.txt provides more complete step-by-step example on how a
test setup can be built.


wpaspy
------

The python scripts use wpaspy.py to interact with the wpa_supplicant
control interface, but the run-tests.py script adds the (relative)
path into the environment so it doesn't need to be installed.


mac80211_hwsim
--------------

mac80211_hwsim kernel module is available from the upstream Linux
kernel. Some Linux distributions enable it by default. If that's not the
case, you can either enable it in the kernel configuration
(CONFIG_MAC80211_HWSIM=m) and rebuild your kernel or use Backports with
CPTCFG_MAC80211_HWSIM=m to replace the wireless LAN components in the
base kernel.


sudo
----

Some parts of the testing process requires root privileges. The test
scripts are currently using sudo to achieve this. To be able to run the
tests, you'll probably want to enable sudo with a timeout to not expire
password entry very quickly. For example, use this in the sudoers file:

Defaults        env_reset,timestamp_timeout=180

Or on a dedicated test system, you could even disable password prompting
with this in sudoers:

%sudo   ALL=NOPASSWD: ALL


Other network interfaces
------------------------

Some of the test scripts are still using hardcoded interface names, so
the easiest way of making things work is to avoid using other network
devices that may use conflicting interface names. For example, unload
any wireless LAN driver before running the tests and make sure that
wlan0..4 gets assigned as the interface names for the mac80211_hwsim
radios. It may also be possible to rename the interface expectations in
run-tests.py to allow other names to be used.

Please also note that some commonly enabled tools, like NetworkManager,
may end up trying to control new network interfaces automatically. This
can result in conflicts with the test scripts and you may need to
disable such network services or at least mark the mac80211_hwsim wlan#
interfaces as umanaged. As an example, this can be done in
/etc/NetworkManager/NetworkManager.conf with following addition:

[keyfile]
unmanaged-devices=mac:02:00:00:00:00:00;mac:02:00:00:00:01:00;mac:02:00:00:00:02:00;mac:02:00:00:00:03:00;mac:02:00:00:00:04:00


Running tests
-------------

Simplest way to run a full set of the test cases is by running
run-all.sh in tests/hwsim directory. This will use start.sh to load the
mac80211_hwsim module and start wpa_supplicant, hostapd, and various
test tools. run-tests.sh is then used to run through all the defined
test cases and stop.sh to stop the programs and unload the kernel
module.

run-all.sh can be used to run the same test cases under different
conditions:

# run normal test cases
./run-all.sh

# run normal test cases under valgrind
./run-all.sh valgrind

# run normal test cases with Linux tracing
./run-all.sh trace

# run normal test cases with multi channel support (see details below)
./run-all.sh channels=<num of channels>

run-all.sh directs debug logs into the logs subdirectory (or $LOGDIR if
present in the environment). Log file names include the current UNIX
timestamp and a postfix to identify the specific log:
- *.log0 = wpa_supplicant debug log for the first radio
- *.log1 = wpa_supplicant debug log for the second radio
- *.log2 = wpa_supplicant debug log for the third radio
- *.hostapd = hostapd debug log
- hwsim0 = wlantest debug log
- hwsim0.pcapng = capture with all frames exchanged during the tests
- *.log = debug prints from the test scripts
- trace.dat = Linux tracing record (if enabled)
- hlr_auc_gw - hlr_auc_gw (EAP-SIM/AKA/AKA' authentication) log
- auth_serv - hostapd as RADIUS authentication server log


For manual testing, ./start.sh can be used to initialize interfaces and
programs and run-tests.py to execute one or more test
cases. run-tests.py output verbosity can be controlled with -d (more
verbose debug output) and -q (less verbose output) on the command
line. "-f <module name>" (pointing to file test_<module name>.py) can be
used to specify that all test cases from a single file are to be
run. Test name as the last command line argument can be specified that a
single test case is to be run (e.g., "./run-tests.py ap_pmf_required").

Notice that some tests require the driver to support concurrent
operation on multi channels in order to run. These tests will be skipped
in case the driver does not support multi channels. To enable support
for multi channel, the number of supported channel is passed as an
argument to run-all.sh or start.sh


Adding/modifying test cases
---------------------------

All the test cases are defined in the test_*.py files. These are python
scripts that can use the local helper classes to interact with the test
components. While various python constructs can be used in the scripts,
only a minimal level of python knowledge should really be needed to
modify and add new test cases. The easiest starting point for this is
likely to take a look at some of the example scripts. When working on a
new test, run-tests.py with -d and the test case name on the command
line is a convenient way of verifying functionality.

run-tests.py will automatically import all test cases from the test_*.py
files in this directory. All functions starting with the "test_" prefix
in these files are assumed to be test cases. Each test case is named by
the function name following the "test_" prefix.


Results database
----------------

run-tests.py can be requested to write results from the execution of
each test case into an sqlite database. The "-S <path to database>" and
"-b <build id>" command line arguments can be used to do that. The
database must have been prepared before this, e.g., with following:

cat | sqlite3 /tmp/example.db <<EOF
CREATE TABLE results (test,result,run,time,duration,build,commitid);
CREATE INDEX results_idx ON results (test);
CREATE INDEX results_idx2 ON results (run);
CREATE TABLE tests (test,description);
CREATE UNIQUE INDEX tests_idx ON tests (test);
CREATE TABLE logs (test,run,type,contents);
CREATE INDEX logs_idx ON logs (test);
CREATE INDEX logs_idx2 ON logs (run);
EOF