Define the following additional TWT attribute for
qca_wlan_vendor_attr_twt_setup:
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL2_MANTISSA to configure the
mantissa in microseconds.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows correct processing of Data frames with Mesh Control field by
finding the LLC/SNAP header after that field.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds new control interface commands TWT_SETUP and TWT_TEARDOWN. For
now, these are only for testing purposes to be able to trigger
transmission of the TWT Action frames without configuring any local
behavior for TWT in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This function can get called with hapd->wpa_auth == NULL from the
control interface handler, so explicitly check for that.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to be able to move from 80 MHz or lower bandwidth to 160
or 80+80 MHz bandwidth (and back) properly without leaving the Beacon
frame VHT elements showing incorrect information.
Signed-off-by: Jouni Malinen <j@w1.fi>
In addition, make the compiler warn if a new enum value is added without
defining the matching mapping to a string.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is more convenient to see the exact error in the debug log instead of
getting noted that something was invalid.
Signed-off-by: Jouni Malinen <j@w1.fi>
The nl_connect is initialized with the process_bss_event() handler.
However, it is used several times with the default valid handler. As a
result, if a message that is only valid for process_bss_event() is
received while the default handler is used, it will be dropped.
This has been observed in a case where during the 4-way handshake, a
Beacon frame is received on the AP side, which triggers a beacon update,
just before receiving the next EAPOL. When send_and_recv_msgs_owner() is
called for sending the NL80211_CMD_SET_BEACON command, the
NL80211_CMD_CONTROL_PORT_FRAME event is already pending. As a result, it
is received with the default handler, which drops it. Since the EAPOL
frame is dropped, the connection attempt fails.
Fix it by using the process_bss_event() handler when the nl_connect
handler is used.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
While it does not look like the stale pointer could have been
dereferenced in practice, it is better not to leave the stale pointer to
freed memory in place to avoid accidental uses.
Signed-off-by: Jouni Malinen <j@w1.fi>
hapd->tmp_eap_user needs to be cleared on interface deinit to avoid
leaving stale pointers to freed memory.
Fixes: ee431d77a5 ("Add preliminary support for using SQLite for eap_user database")
Signed-off-by: Jouni Malinen <j@w1.fi>
When an interface is disabled, e.g. due to radar detected,
hapd->time_adv is freed by hostapd_free_hapd_data(), but later
used by ieee802_11_build_ap_params() calling hostapd_eid_time_adv().
Thus hapd->time_adv needs to be cleared as well.
Fixes: 39b97072b2 ("Add support for Time Advertisement")
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The roam D-Bus and ROAM control itnerface commands flip the reassociate
bit before calling wpa_supplicant_connect(). wpa_supplicant connect
eventually aborts ongoing scans (if any), which causes scan results to
be reported. Since the reassociate bit is set, this will trigger a
connection attempt based on the aborted scan's scan results and cancel
the initial connetion request. This often causes wpa_supplicant to
reassociate to the same AP it is currently associated to instead of the
explicitly requested roaming target.
Add a roam_in_progress flag to indicate that we're currently attempting
to roam via an explicitly request to a specific BSS so that we don't
initiate another connection attempt based on the possibly received scan
results from a scan that was in progress at the time the roam command
was received.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Add a QCA vendor attribute to configure the driver to allow the 6 GHz
connection with all security types. This attribute is used for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to ignore SAE H2E requirement mismatch for 6
GHz connection. This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
os.stat(path) failure is an ambigious indication of the control
interface "path" type (UDP hostname vs. UNIX domain socket path). The
path may be a valid UNIX domain socket path, but that socket could have
been removed just before reaching here. At least the hwsim test case
concurrent_p2pcli managed to hit the "connect exception" print below
from UDP handling even when using a UNIX domain socket.
Work around incorrect determination of control interface socket type by
assuming anything starting with '/' is a UNIX domain socket and not a
hostname.
Fixes: a2c88a8025 ("wpaspy: Add support for UDP connection")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Need to close the WpaSupplicant instance on the extra radio before
returning from this test case since that interface is going to be
removed and WpaSupplicant.__del__() can time out on trying to detach the
monitor connection after that.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
