This syncs the test cases with the implementation change in station's MB
IE creation. FST tests should expect MB IE regardless of the station
connection state and whether the current connection is FST-enabled or
not. This fixes the follow test cases that started reporting failures
with the previous commit change in src/fst/fst_group.c:
fst_disconnect_1_of_2_stas_from_non_fst_ap
fst_sta_connect_to_non_fst_ap
fst_second_sta_connect_to_non_fst_ap
fst_disconnect_2_of_2_stas_from_non_fst_ap
fst_second_sta_connect_to_fst_ap
fst_disconnect_1_of_2_stas_from_fst_ap
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a test to verify that a P2P GO does not start a CSA
once invitation signalling is done, and the P2P client is
about to connect.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This test case was failing if a PropertiesChanged signal for P2P peer
gets delivered from a previous test case. Avoid that by waiting for the
new group to be formed before processing any PropertiesChanged signals.
This failure was triggered by the following test case sequence:
dbus_p2p_two_groups dbus_p2p_group_idle_timeout
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like a previous P2P test case can cause the initial single
channel scan in ap_open_select_twice take more than five seconds in some
cases. While that is not really expected behavior, this test case should
not fail. Increase the timeout to avoid reporting false failures here.
This could be triggered with the following test case sequence:
p2p_msg_unexpected_go_neg_resp ap_open_select_twice
Signed-off-by: Jouni Malinen <j@w1.fi>
These test cases depend on the HT40 co-ex scans not swapping PRI/SEC
channels. It was possible for a test case to fail, e.g., in the
following sequence: ap_ht40_5ghz_match ap_vht80b.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that the second SELECT_NETWORK for the same network starts
a new scan immediately if the previous connection attempt is waiting for
the next scan iteration to start.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This avoids issues with following test cases failing due to unexpected
starting state. This issue showed up with the following hwsim test case
sequence:
fst_setup_mbie_diff fst_dynamic_iface_attach
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the WPS PBC state to get cached through to the
following test cases and that would trigger false failures. Fix this by
explicitly clearing the scan cache at the end of ap_wps_per_station_psk.
This issue was triggered with the following test case sequence:
ap_wps_per_station_psk autogo_pbc
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed since the forced OOM may have forced the cached
information to be invalid or dropped. This issue was hit with the
following hwsim test case sequence:
ap_interworking_scan_filtering fst_sta_config_llt_large dbus_connect_oom
wpas_ctrl_enable_disable_network
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for dev[2] to be left with non-default config_methods
parameter at the end of the test case and that could result issues in
following test cases. This hit a failure in the following sequence:
wpas_ctrl_set_wps_params p2ps_channel_active_go_and_station_same
Signed-off-by: Jouni Malinen <j@w1.fi>
Due to a typo in a function name, this test case ended up running
without the final cleanup. That could result in the following test cases
failing, e.g., when running this sequence:
wifi_display_parsing dbus_p2p_go_neg_auth
Signed-off-by: Jouni Malinen <j@w1.fi>
The previously used invalid values will become allowed with the
following commits, so change the test case to use values that both were
and will continue to be invalid to avoid unnecessary failures.
Signed-off-by: Jouni Malinen <j@w1.fi>
autogo_scan verifies the special case where a Probe Response frame
without P2P IE has been received from a GO (e.g., due to a non-P2P
interface requesting a scan) and P2P information from a Beacon frame
needs to be used instead to determine that the group is persistent.
Signed-off-by: Jouni Malinen <j@w1.fi>
SAVE_CONFIG command on the global control interface tries to save
the config file on all interfaces. The test disabled updating the
config file only on one interface, thus for configurations that
support a dedicated P2P Device interface, saving the config file
would still have succeeded on the P2P Device interface.
Fix the test by disabling updating the configuration file on the global
control interface (which will, in practice, disable this for the P2P
Device interface) in addition to disabling it on the main interface.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
mac80211_hwsim only supports 2 different MAC addresses.
Configurations that use a dedicated P2P Device interface already
use these 2 addresses, so adding another interface on the same
PHY results in a duplicated MAC address.
Fix this by changing the MAC address of the added interface to make
sure the new interface has a unique MAC address.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Set the bridge ageing to 1 sec to make the bridge clear unused
addresses after this interval. Otherwise the test depends on
the local configuration of brctl.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
