This commit enhances QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES to
also be an event, aimed to notify the link status (EX: connected
stations status on an AP link).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When external authentication is used, a specific netlink socket is used
to send the connect command. If the same socket is not used for
disconnect command, cfg80211 will discard the command. This constraint
was added into the kernel in commit bad292973363 ("nl80211: Reject
disconnect commands except from conn_owner"). That requires an update
for the hostap.git commit 40a68f3384 ("nl80211: Create a netlink
socket handle for the Connect interface").
Add a new flag into struct i802_bss to indicate if the special
nl_connect socket was used for the connect command. When sending
disconnect command this flag is tested to select the correct socket.
Signed-off-by: Cedric Izoard <cedric.izoard@ceva-dsp.com>
When selecting SSID to start external authentication procedure also
check the key_mgmt field as several network configuration may be defined
for the same SSID/BSSID pair. The external authentication mechanism is
only available for SAE.
Signed-off-by: Cedric Izoard <cedric.izoard@ceva-dsp.com>
The call to remove_group() may fail, in which case all following
cleanup is skipped. This may result in failing many tests since
cleanup did not complete successfully.
Fix this by calling remove_group() after other cleanup is done so
even it fails it will not affect the following tests.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add documentation to the wpa_signal_info structure.
Add a define for an invalid noise value.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
BSS additional/removal cases were not considered at all in the previous
implementation of hostapd configuration file reloading on SIGHUP. Such
changes resulted in num_bss values getting out of sync in runtime data
and configuration data and likely dereferencing of freed memory (e.g.,
when removing a BSS).
Fix this by forcing a full disable/enable sequence for the interface if
any BSS entry is added/removed or if an interface name changes between
the old and the new configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Implement ECDSA signing functionality in the Python test script for
generating a valid signedConnector. This allows coverage of DPP config
object testing to be increased more easily.
Signed-off-by: Jouni Malinen <j@w1.fi>
A local memory allocation failuring during GAS Comeback Response frame
generation could result in freeing the response context without removing
it from the list. This would result in dereferencing freed memory when
processing the next comeback request.
Signed-off-by: Jouni Malinen <j@w1.fi>
If local memory allocation for the GAS response failed, couple of error
paths ended up leaking some memory maintaining the state for the
exchange. Fix that by freeing the context properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
The GAS client processing of the response callback for DPP did not
properly check for GAS query success. This could result in trying to
check the Advertisement Protocol information in failure cases where that
information is not available and that would have resulted in
dereferencing a NULL pointer. Fix this by checking the GAS query result
before processing with processing of the response.
Signed-off-by: Jouni Malinen <j@w1.fi>
This lets us know whether we can attempt to use FT-PSK, FT-EAP,
FT-EAP-SHA384, FT-FILS-SHA256 or FT-FILS-SHA384.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Based on Jouni Malinen's [76055b4c6 "tests: D-Bus Get/Set Pmf"], modified
to use the correct "s" signature for the "Pmf" property.
Removed the negative test cases, because the synthesized property doens't
seem to do error checking upon being set.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
This reverts commit adf8f45f8a.
It is basically all wrong. The Pmf property did exist, with a signature of
"s" as documented in doc/dbus.doxygen. It was synthesized from
global_fields[].
The patch added a duplicate one, with a signature of "u", in violation
of D-Bus specification and to bemusement of tools that are careful
enough:
$ busctl introspect fi.w1.wpa_supplicant1 /fi/w1/wpa_supplicant1/Interfaces/666
Duplicate property
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Make the buf_len calculation match more closely with the following
wpa_buf*() operations. The extra room from the existing elements was
apparently sufficiently large to cover this, but better add the two
octet header explicitly.
Signed-off-by: Jouni Malinen <j@w1.fi>
The maximum size of a Mesh Peering Management element in the case
of an AMPE close frame is actually 24 bytes, not 23 bytes, plus the
two bytes of the IE header (IEEE Std 802.11-2016, 9.4.2.102). Found by
inspection.
The other buffer components seem to use large enough extra room in their
allocations to avoid hitting issues with the full buffer size even
without this fix.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
use 'printf' instead of 'echo -n', to suppress the following warning:
In POSIX sh, echo flags are undefined. [SC2039]
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
The hwsim's start.sh script spawns hostapd process using "sudo".
Since sudo forks a child process, $! holds the pid of sudo itself.
Fix that by storing the PID of the child process instead.
Since in VM "sudo" is replaced with a dummy script, pass an additional
argument to run-all.sh and start.sh scripts to indicate that they are
running inside a VM.
This is needed to fix ap_config_reload and ap_config_reload_file test
cases on some platforms where sudo is apparently not relaying the
signals properly.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In ap_acl_deny test, the AP doesn't send probe responses during scan due
to ACL reject. As the result, dev[0] might miss the AP's Beacon frame
because the dwell time is too short. Make the test more robust and
trigger passive scan, and by that increase the probability of hearing
the AP.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Back in December 2017, Jouni fixed the output side since that was
causing a kernel message to be printed, but the input side should
also be fixed, otherwise it will not work correctly on big-endian
platforms.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The option to get DPP configurator key in hostapd_cli was named
incorrectly. It was wrongly pointing to dpp_configurator_remove. Fix
this by using the correct name.
Signed-off-by: Rohit Damodaran <Rohit_Damodaran@comcast.com>
Parse the OSEN IE from the AP to determine values used in the AssocReq
instead of using hardcoded cipher suites. This is needed to be able to
set the group cipher based on AP advertisement now that two possible
options exists for this (GTK_NOT_USED in separate OSEN BSS; CCMP or
GTK_NOT_USED in shared BSS case). Furthermore, this is a step towards
allowing other ciphers than CCMP to be used with OSEN.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG vendor command
to set the priorities among different types of traffic of
WLAN/BT/Zigbee during coex scenarios.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add interface for drivers to report changes in TX/RX throughput
dynamically to user space. This information can be used by userspace
tools to tune kernel's TCP parameters in order to achieve peak
throughput. The driver may optionally provide guidance on which TCP
parameters to be configured for optimal performance along with the
values to be configured.
The TCP parameters that need to be tuned for peak performance are not
interface specific. Based on the guidance from the driver and
considering the other interfaces that may be affected with the new
configurations, a userspace tool has to choose the values to be
configured for these parameters to achieve optimal performance across
interfaces.
The throughput levels informed by the driver with this event are only
for providing guidance on TCP parameter tuning from userspace. The
driver may change the thresholds used to decide low or medium or high
throughput levels based on several parameters based on the PHY layer
capacity in the current connection, the number of packets being
dispatched per second, or the number of packets pending in queues, etc.
The throughput levels may not be consistent with the actual throughput
of the link.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The OSU Providers List includes two providers, so there should be two
OSU_METHOD values listed just like there was two OSU_SERVER_URI URLs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to allow sigma_dut to enable ap_isolate=1. In addition,
verify that the two associated STAs with RSN(EAP) and OSEN cannot
exchange frames between them.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure action
frame transmission in HE trigger based PPDU.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure HE
single user PPDU transmission.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attributes to configure HE
operating mode control field bandwidth, number of spatial streams, and
UL MU disable configuration. Define a new attribute to clear the
previously set HE OM control field configuration. This is used for
testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not try to determine the length of the T&C Server URL before checking
that the URL is available. This got broken in a change to move the
handling to the AS. hostapd could potentially have hit a NULL pointer
dereference if the authentication server sent an unconsistent set of T&C
information.
Fixes: d4e39c51f8 ("HS 2.0: Move Terms and Conditions Server URL generation from AP to AS")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Earlier, the OCE flags were checked during hostapd initialization. This
doesn't address few cases like for example when the interface is added
from control interface. Move the OCE flag checks to the functions that
are forming the MBO/OCE IEs to cover all the different paths for
enabling a BSS. Also use macros as appropriate for readability.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hs20-osu-client refused to do anything if it could not find devinfo.xml
from the current working directory. This is a bit excessive since that
file was used in init_ctx() only to fill in ctx->devid which is used
when constructing OMA DM messages.
Move the check for ctx->devid into OMA DM specific code so that other
hs20-osu-client functionality can be used without the devinfo.xml file.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
