This element is required to have at least four octets of actual payload.
This was not previously verified before use and the extra buffer data
after the IE might have been used instead if a received WNM-Sleep Mode
Response frame was invalid.
Signed-off-by: Jouni Malinen <j@w1.fi>
This moves the type cast needed for the current driver interface to
ieee802_11_set_tfs_ie() to allow the WNM-Sleep parsing routines to use
const pointers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
If hostapd or wpa_supplicant is built from a git repository, add a
VERSION_STR postfix from the current git branch state. This is from "git
describe --dirty=+". VERSION_STR will thus look something like
"2.6-devel-hostap_2_5-132-g4363c0d+" for development builds from a
modified repository.
This behavior is enabled automatically if a build within git repository
is detected (based on ../.git existing). This can be disabled with
CONFIG_NO_GITVER=y in wpa_supplicant/.config and hostapd/.config.
Signed-off-by: Jouni Malinen <j@w1.fi>
Vendor specific IEs added to frame type P2P_ASSOC_RESP are saved in
the interface context, but as they are added as part of the P2P IEs,
they need to be saved in the global P2P context.
Fix this by directing vendor specific IEs added to P2P_ASSOC_RESP
frame type to the P2P context.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This makes it easier to analyze debug logs for issues related to
multiple pending Action TX frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not expire scan results entries based on scan results from a scan
that was aborted. The aborted scan did not scan all the requested
channels or SSIDs, so the fact that a BSS is missing from the scan
results does not mean it is not available.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
CTWindow was set for all AP interfaces if the driver supports it and
this parameter is set in wpa_supplicant configuration. This results in
failing to start an AP that is not a P2P GO as this setting is rejected
by the driver.
Fix that by setting the CTWindow only for P2P GO interface.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a global D-Bus handler ExpectDisconnect for setting
wpa_s->own_disconnect_req flag. This flag will prevent wpa_supplicant
from adding blacklists and requesting incomplete scan upon the incoming
disconnection. This is mainly meant for a case where suspend/resume is
used and some external component knows about that and can provide the
information to wpa_supplicant before the disconnection happens.
Signed-off-by: Ningyuan Wang <nywang@google.com>
It was possible for wpa_s->own_disconnect_req to be left set to 1 from a
disconnection attempt from a prior connection. This could then prevent
proper connection failure processing with the new connection in
wpas_connection_failed(). This was triggered by the following hwsim test
case sequence: wpas_mesh_secure sae_no_ffc_by_default. In this sequence,
the SAE failure due to unsupported group did not result in proper
wpas_connection_failed() processing and retry.
Fix this by clearing wpa_s->own_disconnect_req in
wpa_supplicant_associate() before starting a new connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When one peer doesn't include a persistent group info in PD Request
the other peer shouldn't report a persistent group usage with this
peer even if such a persistent group exists locally. This condition
could be violated in the previous implementation.
In case a local persistent group exists and the
wpas_p2ps_prov_complete() function is called with persist_ssid parameter
set to NULL, wpa_supplicant reported P2PS-PROV-DONE with persist=<idx>
instead of conncap=<role> parameter.
This happened because the wpas_p2p_get_persistent() function was called
without verification whether the persist_ssid was set to NULL. In this
case the wpas_p2p_get_persistent() returns the first existing persistent
group matching the P2P Device Address without verifying the group's
SSID. After that the group ID is used as persist=<idx> parameter of
P2PS-PROV-DONE event.
Fix the issue by adding persist_ssid and persist_ssid_size verification
as a condition for the wpas_p2p_get_persistent() call.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
On successful P2P PD, report the chosen frequency in case the local
device is going to be the P2P GO, so in can later be used to instantiate
the new P2P GO, etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add operating channel selection and channel list processing similar to
that done when building GO Negotiation Request, i.e., consider the
currently used channels, configured channels, etc.
P2PS introduces a flow where a responder needs to provide channel data
without being previously aware of the current constraints, i.e., the
channels currently in use by other interfaces. To handle this, extend
the get_group_capability() callback to also handle channel selection
aspects of group capabilities.
In case there is an active P2P GO that is going to be used for the P2PS
PD, force its current operating frequency in the PD attributes.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Change the connection capability handling so that in case there are no
active roles, the peer has an active GO, and the advertisement supports
operation as a client, the returned connection capability is set to
client.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The code was iterating all the interfaces, and for each interface
iterated all the network blocks to count active P2P GO and P2P Client
interfaces.
Change the code to reuse wpas_p2p_get_go_group() to get a P2P GO
interface and add wpas_p2p_get_cli_group() and use it to find a
P2P Client interface, and use these objects when evaluating the
group capability.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Re-factor wpas_p2p_get_go_group() to:
1. Skip the dedicated P2P Device management interface if it is used.
2. Instead of iterating all the interface configured networks,
only access the current_ssid pointer to check if the current
interface is acting as a persistent P2P GO.
To avoid code duplication, also re-factor wpas_p2p_group_go_ssid()
to call wpas_p2p_get_go_group().
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This allows wpa_supplicant to expose internally unknown ANQP-elements in
the BSS command. For example, "ANQP_GET <BSSID> 265" can be used to
fetch the AP Geospatial Location ANQP-element and if the AP has this
information, the "BSS <BSSID>" command will include the response as
"anqp[265]=<hexdump>".
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The switch to BoringSSL broke keystore-backed keys because
wpa_supplicant was using the dynamic ENGINE loading to load
the keystore module.
The ENGINE-like functionality in BoringSSL is much simpler
and this change should enable it.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
IEEE Std 802.11-2012 13.3.1 states that the AID should be generated on
the local node for each peer. Previously, we were using the peer link ID
(generated by the peer) which may not be unique among all peers. Correct
this by reusing the AP AID generation code.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
dl_list_del() must be called before freeing the list entries. Neither of
these cases caused problems because the full list data structure was
freed, but still, it is better to do this properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some operations like a new scan result processing can result in large
number of wpa_supplicant control interface messages being generated.
Especially with multiple control interface monitors, this could result
in hitting the output queue length maximum and event messages getting
dropped. In worst case, that could even result in hitting ten
consecutive sendto() errors which could result in an attached monitor
socket getting detached.
Avoid this type of issues by throttling monitor event transmission based
on the output queue length. If more than half of the maximum send buffer
is used, postpone sending of following event messages until the pending
output queue has dropped below the limit.
Signed-off-by: Jouni Malinen <j@w1.fi>
The CSA channel and operating class values need to be set for all types
of channel switch (i.e., either if it's triggered by the control
interfaces or due to the GO-follows-STA flow). To do so, move the code
that sets them from the GO-follows-STA flow to the more generic
hostapd_fill_csa_settings() function.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Some management frames contain CSA counters which should be updated by
kernel. Change driver op send_mlme() allowing to send a frame,
specifying an array of offsets to the CSA counters which should be
updated. For example, CSA offsets parameters should be specified when
sending Probe Response frames during CSA period.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Channel switch notification was handled only for AP/GO interfaces. As
the notification can be sent on other interface types as well, extend
the handling to handle other interface types.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add new GO frequency move policy. The P2P_GO_FREQ_MOVE_SCM_ECSA prefers
SCM if all the clients advertise eCSA support and the candidate
frequency is one of the group common frequencies.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Do not consider moving GOs to a new channel if one of them is in the
middle of CSA. In addition, call wpas_p2p_update_channel_list() after
EVENT_CH_SWITCH is handled.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
wpas_p2p_move_go_csa() uses wpas_p2p_init_p2p_params() to select the
frequency to move to. However, it is possible that all the channels are
already used, so the selection of a new frequency would fail, although
the frequency used by the P2P GO should not be considered as used if it
is the only one using it.
To overcome this, allow the frequency selection to continue even if all
the frequencies are in use, but the frequency used by the P2P GO is not
used by any station interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Use channel switch mechanism to move a P2P GO to a new channel,
when required. In order to be able to reconfigure the GO channel,
split wpa_supplicant_conf_ap() function, so the frequency
configuration part can be reused to find additional CSA settings.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The readline library depends on ncurses, so it should be set before
ncurses on the linker command line to be able to be statically linked
successfully.
Signed-off-by: David du Colombier <0intro@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
This allows the binary sizes to be reduced if no support for nl80211
vendor extensions are needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit contains the necessary changes to parallelize
distinct radio work operations which are different in type and
the band used, only when the underlying driver is capable of
supporting such simultaneous offchannel operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow wpa_supplicant to use vendor scan (if supported by the driver)
together with the normal nl80211 scan and handling external scan events.
Since this results in possibility of concurrent scan operations, some of
the operations related to scan results need to check more carefully when
an event is relevant for a specific interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is equivalent to the P2P_EVENT_INVITATION_RECEIVED signal on the
control interface. It can be used to sent the Invitation Received signal
to applications written using D-Bus.
Signed-off-by: Maneesh Jain <maneesh.jain@samsung.com>
Fix a bug in wpas_ap_ch_switch() function, which didn't pass VHT
frequencies correctly to hostapd_event_ch_switch().
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Fix an iteration bug in get_shared_radio_freqs_data when building
freqs_data array. Only the last used-by flag was maintained instead of
making this a bitfield of all found uses.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This corrects the type of dev_passwd_id in GONegotiationRequest event.
This field is packed as DBUS_TYPE_UINT16 but in
wpas_dbus_interface_signals it was "i" which is DBUS_TYPE_INT32.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
Android platform assigns the same socket id if the socket identifier in
conf->ctrl_interface and global->params.ctrl_interface (parameter for
android_get_control_socket) point to the same Android specific control
socket. This ends up having two eloop socket handlers registered for the
same file descriptor and thus, two attempt to receive and process each
command. This can result in unexpected failure, e.g., the prefix IFNAME=
for any command is valid for global socket handler, but results in
UNKNOWN COMMAND response from the per-interface ctrl socket handler).
Since it might be possible to end up with this type of invalid
configuration in OTA upgrade, compare the socket identifiers and do not
open the ctrl socket on the respective interface if both point to same.
This allows the Wi-Fi framework to use the global control interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was already the case for most command sequences, but it was
possible for wpa_s->reassociate to be set to 1 when CTRL-RSP-* commands
were used to set identity, password, or passphrase for EAP
authentication. In such cases, ENABLE_NETWORK issued after the
connection was completed could result in a new connection attempt
(likely reconnection back to the same BSS).
Fix this by checking whether an actual connection is already present
even if wpa_s->reassociate is set when processing the ENABLE_NETWORK
command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for driver-based BSS selection to end up reassociating
back to the current AP. If wpa_supplicant preferred another BSS, it
would have updated the internal knowledge of the AP's WPA/RSN IE when
requesting a new connection. In the special case of existing association
and new association being with the same BSS that is different from the
wpa_supplicant preference, association event processing skipped the
WPA/RSN IE update. This could result in the following 4-way handshake
getting rejected due to incorrectly detected mismatch with AP's RSN/WPA
IE between Beacon/Probe Response frame and EAPOL-Key msg 3/4.
Fix this by updating the AP WPA/RSN IE on all association events when
driver-based BSS selection is used regardless of whether the BSSID
changes. This could also cover a theoretical case of the AP changing its
RSN/WPA IE at the very moment we try to reassociate back to the same
BSS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These prints were at DEBUG level (-d), but they can be very frequent, so
drop them to MSGDUMP (-dd). This allows the prints to be suppressed in
common debugging cases while still leaving them easily enablable to
debug control interface issues without having to enable excessive
debugging.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commands like BSS and GET_NETWORK are used in some cases very frequently
and those can increase the amount of debug information from
wpa_supplicant without significant benefit. These were logged at the
DEBUG level (-d). Move logging of such read-only commands (i.e., no new
wpa_supplicant operation is started based on it) to EXCESSIVE level
(-ddd) which was already used for the PING command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When wpa_init() in __mesh_rsn_auth_init() failed, empty rsn->auth caused
segmentation fault due to NULL pointer dereference when wpa_deinit() was
called. Fix this by checking the pointer before executing deinit steps.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The RSN IE is required by IEEE Std 802.11-2012 on SAE use case:
Table 8-262 Mesh Peering Open frame Action field format
Table 8-263 Mesh Peering Confirm frame Action field format
Add the RSN IE to these frames.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Double the buffer length from 2048 to 4096 to match the length used
currently in wpa_supplicant. This allows wpa_gui to retrieve information
for more networks than previously.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows control interface monitors to get more detailed information
in cases where wpa_supplicant-based SME receives an Authentication frame
with non-zero status code.
Signed-off-by: Jouni Malinen <j@w1.fi>
For now, there is no support for passing extended_capa pointers through
the driver_privsep.c interface from wpa_priv. Avoid leaving bogus
pointers by explicitly clearing these on both wpa_priv and
wpa_supplicant sides.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add more details into configuration comments and a runtime info message
if ap_scan=2 is used with the nl80211 driver interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a new helper function wpa_ctrl_open2() that can be used
instead of wpa_ctrl_open() to override the default client socket
directory. Add optional -s<directory path> argument to hostapd_cli and
wpa_cli to allow the client socket directory to be specified.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the BSS command returned an error if the WSC IE(s) in scan
results could not be parsed. This may be not ideal for all cases, to
instead of rejecting the command completely, return all other
information apart from the WPS information in such a case.
Signed-off-by: Jouni Malinen <j@w1.fi>
scan_freq and freq_list are not parsed correctly by
wpa_config_parse_int_array() if quoted.
Patch for dbus_old_handlers.c, the same change as done by Robert Shade
<robert.shade@gmail.com> for dbus_new_handlers.c in commit
99276998fa ('dbus: Do not quote scan_freq
and freq_list').
Signed-off-by: Jiří Klimeš <jklimes@redhat.com>
While the EAPOL-Key MIC derivation was already changed from SHA256 to
SHA384 for the Suite B 192-bit AKM, KDF had not been updated similarly.
Fix this by using HMAC-SHA384 instead of HMAC-SHA256 when deriving PTK
from PMK when using the Suite B 192-bit AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
Config file is written to a temp file and then it is renamed to the
original config file. However, it is possible that the rename operation
will be commited to storage while file data will be still in cache
causing original config file to be empty or partially written in case of
a system reboot without a clean shutdown. Make this less likely to occur
by forcing the data to be written to the storage device before renaming
the file.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This allows a BSS entry to be expired if the AP has changed its SSID
while maintaining the same BSSID and we are associated with the BSS.
Previously, the same BSSID was enough to mark all BSS entries from the
BSSID as in use regardless of the SSID and as such, they could remain in
the wpa_supplicant BSS table indefinitely as long as the association
remaining.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The P2P group is not yet operating when going through GO Negotiation
exchange. Previously, an old cached scan result could be used to skip
the scan immediately after the GO Negotiation. While this is quite
unlikely to happen in practice, we can easily force a scan here now with
the generic scan_min_time mechanism. Do that to avoid any corner cases
that a previous instance of the group could have if found in cached scan
results.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The P2P group is not yet operating when going through invitation
exchange for re-invocation. Previously, an old cached scan result could
be used to skip the scan immediately after the invitation exchange.
While this may result in the fastest possible connection, it does have
some issues with cases where the GO takes some time to start up. It
would also be at least theoretically possible for some of the BSS
parameters to be different, so having a fresh scan result from the new
GO instance may be desired in any case.
Add a mechanism to skip scan results that have been last updated before
a specific point in time and as the first user for this mechanism,
require chan results to be more recent than the invitation message
exchange for the P2P Client role in persistent group re-invocation case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new script can be used as an example of load testing for RADIUS
authentication servers. It can control multiple eapol_test processes
over the control interface to run EAP-TLS authentication. As an example,
the following commands would run eight instances of eapol_test
concurrently:
for i in 0 1 2 3 4 5 6 7; do
./eapol_test -T /tmp/eapol_test -i $i > eapol_test.log$i &
done
time ./eapol_test.py --ctrl /tmp/eapol_test --num 8 --iter 100
0: PASS 100
1: PASS 100
2: PASS 100
3: PASS 100
4: PASS 100
5: PASS 100
6: PASS 100
7: PASS 100
real 0m0.339s
time ./eapol_test.py --ctrl /tmp/eapol_test --num 8 --iter 100 --no-fast-reauth
0: PASS 100
1: PASS 100
2: PASS 100
3: PASS 100
4: PASS 100
5: PASS 100
6: PASS 100
7: PASS 100
real 0m1.876s
Signed-off-by: Jouni Malinen <j@w1.fi>
The -T<ctrl_iface> command line argument can now be used to start
eapol_test in mode where the configuration file is not needed and the
authentication operations are started through the control interface.
Network profile is also managed through the control interface in this
case. This can be used to provide more control for scripted RADIUS
authentication server testing.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new -i<ifname> command line argument can be used to specify the name
of the interface to use. This is mainly to allow unique control
interface names to be defined without having to use multiple
directories.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like BoringSSL has removed the AES_wrap_key(), AES_unwrap_key()
API. This broke wpa_supplicant/hostapd build since those functions from
OpenSSL were used to replace the internal AES key wrap implementation.
Add a new build configuration option
(CONFIG_OPENSSL_INTERNAL_AES_WRAP=y) to allow the internal
implementation to be used with CONFIG_OPENSSL=y build to allow build
against the latest BoringSSL version.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_s->scan_req needs to be set in these cases to get correct scanning
behavior. This is mainly needed for starting of AP mode operation
immediately in ap_scan=2 case.
This fixes an issue that was found with mac80211_hwsim test cases in the
following sequence: dbus_autoscan dbus_ap_scan_2_ap_mode_scan
Signed-off-by: Jouni Malinen <j@w1.fi>
If P2PS PD concludes to use default P2PS method wpas_p2p_scan_res_join()
ignores this value and tries to perform a redundant legacy PD.
Fix this by considering WPS_P2PS method too.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Ordering the units before network.target causes them to be stopped
after network.target on shutdown. This ensures that any network
filesystems will be unmounted before wpa_supplicant is killed.
Adding Wants=network.target ensures that network.target will be included
in the active dependency graph. This is typical of units which are
involved in networking setup functions.
Signed-off-by: Mike Gilbert <floppym@gentoo.org>
This makes it easier to track the output queue state on a control
interface socket and determine what could be causing issues with running
out of space in the buffer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
PNO was stopped by the wpa_supplicant during the connection attempts or
while handling disassociation indication. External entities, mainly, the
Android Wi-Fi framework, does not expects PNO to be stopped by other
modules. Hence, do not stop the sched_scan in these scenarios if it is
triggered externally for PNO.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant_assoc_try() would result in the currently operating AP to
get stopped if wpa_supplicant_scan() ends up getting triggered without
MANUAL_SCAN_REQ while operating an AP. With ap_scan=2, this could
resulted in unintentional stopping of AP mode operations, so check
explicitly for that case and skip the wpa_supplicant_assoc_try() call if
needed to avoid this.
Signed-off-by: Jouni Malinen <j@w1.fi>
The D-Bus Scan() handler was setting wpa_s->scan_req = MANUAL_SCAN_REQ
on the code path that used wpa_supplicant_req_scan(). However, it did
not do anything similar for the cases where
wpa_supplicant_trigger_scan() is called directly. This could result in
unexpected wpa_s->last_scan_req value and incorrect behavior especially
when using ap_scan=2 and running a scan while operating in AP mode. Fix
this by explicitly setting wpa_s->last_scan_req = MANUAL_SCAN_REQ when
using wpa_supplicant_trigger_scan() from the Scan() handler.
Signed-off-by: Jouni Malinen <j@w1.fi>
When using P2P invitation to re-invoke a persistent P2P group without
specifying the operating channel, query the driver for the preferred
frequency list, and use it to select the operating channel of the group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
With the radio work design, it is possible for a network entry to get
disabled (e.g., DISABLE_NETWORK <id>) during the time the connect or
sme-connect radio work waits to start. Previously, only the validity of
the BSS entry and BSSID/SSID was verified when starting the actual
connection step. Add call to wpas_network_disabled() to those checks to
catch the case where the network profile is disabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When starting an autonomous GO without specifying the operating channel,
query the driver for the preferred frequency list, and use it to select
the operating channel of the GO (if supported).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When P2PS PD with default P2PS method is done, the peer that becomes GO
should authorize the client. However, P2PS specification doesn't require
the client to include its intended interface address in PD
Request/Response. As a result, the P2P Client's interface address may not
be known and any address may need to be authorized.
Previously, client's P2P Device Address was used for authorization,
which is not correct when a dedicated interface is used for P2P Client.
This is not resulting in a connection failure, however it causes a
significant delay (until WPS_PIN_TIME_IGNORE_SEL_REG elapses). Fix this
by authorizing the intended interface address, if known; or any address,
if not known.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Use NULL to indicate if the address is not available instead of fixed
00:00:00:00:00:00. wpas_p2ps_prov_complete() already had code for
converting NULL to that all zeros address for event messages.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Change P2PS P2P-PROV-SHOW-PIN/P2P-PROV-ENTER-PIN event notifications
on PD Request/Response handling to meet required P2PS behavior.
The new implemented scheme:
1. For a legacy P2P provision discovery the event behavior remains
without changes
2. P2PS PD, advertiser method: DISPLAY, autoaccept: TRUE:
Advertiser: SHOW-PIN on PD request replied with a status SUCCESS
Seeker: ENTER-PIN on PD response received with a status SUCCESS
3. P2PS PD, advertiser method: DISPLAY, autoaccept: FALSE:
Advertiser: SHOW-PIN on PD request replied with a status
INFO_CURRENTLY_UNAVAILABLE
Seeker: ENTER-PIN on Follow-on PD request with a status
SUCCESS_DEFERRED
4. P2PS PD, advertiser method: KEYPAD, autoaccept: TRUE/FALSE:
Advertiser: ENTER-PIN on PD request replied with a status
INFO_CURRENTLY_UNAVAILABLE
Seeker: SHOW-PIN on PD response received with a status
INFO_CURRENTLY_UNAVAILABLE
This change in behavior breaks the existing test cases
p2ps_connect_keypad_method_nonautoaccept and
p2ps_connect_display_method_nonautoaccept. Those will be fixed in a
followup commit.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
P2P_FLUSH command did not cleanly clear the p2p_go_avoid_freq data
structure, and left it in an inconsistent state, where the range field
was NULL but the num field was not 0. This would have resulted in an
invalid memory access in freq_range_list_includes().
Fix this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
A P2P GO channel switch should not be triggered in all cases that
require channel list update. Specifically, a P2P GO CS should not
be triggered in case that the P2P GO state changed or in case that
that the P2P GO has just completed a CS.
To fix this, add reason code to wpas_p2p_channel_list_update() and
trigger CS flow only for the relevant cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
A newly created GO might move to another channel before the client was
able to connect to it. This creates a situation where the client
searches the GO on the channel agreed upon during GO Negotiation or
invitation signaling, while the GO is on another channel. This in turn
might lead to delayed connection or connection failure and group
removal.
Fix this by disallowing a GO CS as long as there is some activity that
should delay the switch. If a GO move is not allowed, set a timeout to
re-attempt the move.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Re-factor the code, so channel optimizations would be also triggered
upon the following changes: channel updates from the kernel,
disallow_freq interface, etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Update hardware features for all interfaces inside the loop, don't treat
the calling wpa_s instance specially. Perform the P2P channel list
updates after the hardware features are updated. This will prevent P2P
from relying on stale information.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Not all paths in wpas_p2p_init_go_params() verified that the candidate
frequency can be used for GO purposes. Fix this, and in addition
re-factor the code to put better emphasis on the frequency selection
priorities.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Remove the code that considers removing GOs from their current
channel due to frequency interference, as this is already handled
as part of the P2P channels update.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
A P2P GO interface that was instantiated after a GO Negotiation or
Invitation holds the intersection of frequencies between the GO and the
client. In case the GO is going to move to another frequency, allow it
to move only to a frequency that is also supported by the client.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add a function to compute the group common frequencies, and
use it to update the group_common_frequencies as part of the
channel switch flows.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Upon any change in the currently used channels evaluate if a GO should
move to a different operating frequency, where the possible scenarios:
1. The frequency that the GO is currently using is no longer valid,
due to regulatory reasons, and thus the GO must be moved to some
other frequency.
2. Due to Multi Concurrent Channel (MCC) policy considerations, it would
be preferable, based on configuration settings, to prefer Same
Channel Mode (SCM) over concurrent operation in multiple channels.
The supported policies:
- prefer SCM: prefer moving the GO to a frequency used by some other
interface.
- prefer SCM if Peer supports: prefer moving the GO to a frequency
used by some other station interface iff the other station
interface is using a frequency that is common between the local and
the peer device (based on the GO Negotiation/Invitation signaling).
- Stay on the current frequency.
Currently, the GO transition to another frequency is handled by a
complete tear down and re-setup of the GO. Still need to add CSA flow to
the considerations.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This makes it possible to use these helper functions from hostapd as
well as the current use in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This buffer is owned by the FST module, so mark it const in the
set_ies() callback to make it clearer which component is responsible for
modifying and freeing this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
NO_EVENTS parameter was added to STATUS command by commit
a6ab82d7b4 ('Android: Add NO_EVENTS
parameter to status command'). This patch adds handling of the new
parameter in wpa_cli so that "status no_events" can be used to specify
this parameter.
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
Currently wpa_cli connects to global control interface if -i/-p
parameters are not specified. wpa_cli on global control interface
is not useful since the prefix like "IFNAME=wlan0 " needs to be
added to some commands like "IFNAME=wlan0 scan". And, specifying
-i/-p parameters every time is annoying. To improve efficiency of
debugging, this patch enables to make wpa_cli work without extra
parameters.
If you still want to connect to global control interface,
the following command can be used instead:
$ wpa_cli -g@android:wpa_wlan0 (or -gwlan0)
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
The mesh SAE auth often fails with master branch. By bisect I found
commit eb5fee0bf5 ('SAE: Add side-channel
protection to PWE derivation with ECC') causes this issue. This does not
mean the commit has a bug. This is just a CPU resource issue.
After the commit, sae_derive_pwe_ecc() spends 101(msec) on my PC (Intel
Atom N270 1.6GHz). But dot11RSNASAERetransPeriod is 40(msec). So
auth_sae_retransmit_timer() is always called and it can causes
continuous frame exchanges. Before the commit, it was 23(msec).
On the IEEE 802.11 spec, the default value of dot11RSNASAERetransPeriod
is defined as 40(msec). But it looks short because generally mesh
functionality will be used on low spec devices. Indeed Raspberry Pi B+
(ARM ARM1176JZF-S 700MHz) requires 287(msec) for new
sae_derive_pwe_ecc().
So this patch makes the default to 1000(msec) and makes it configurable.
This issue does not occur on infrastructure SAE because the
dot11RSNASAERetransPeriod is not used on it.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Otherwise P2P remains in provisioning state and continues to skip
extended listening forever.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Allow proper update for listen_reg_class and listen_channel with
changed_parameters [CFG_CHANGED_P2P_LISTEN_CHANNEL] configuration for
command received through ctrl_interface. Without this, "set
p2p_listen_channel" and "set p2p_listen_reg_class" do not update the
listen channel. The D-Bus version was already setting these flags.
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
This variable is needed to figure out whether a wpa_supplicant interface
is for a P2P group that is (or was) connected to a specific GO. The
previous implementation was able to find such a case only when there was
an association with the GO. However, this may be needed even if there is
a temporary disconnection from the GO. Keep the GO device address
information over such temporary disconnections and only remove it on
group termination. This fixes an issue with D-Bus Peer PropertiesChanged
signals for the Groups property in case a P2P group gets removed due to
group idle timeout instead of explicit group termination command (local
request) or GO notification.
Signed-off-by: Jouni Malinen <j@w1.fi>
The P2P configuration file is wrongly set as STA configuration file,
even though a separate configuration file is mentioned with '-m' option.
Add initialization and deallocation of global.params->conf_p2p_dev to
fix this.
Signed-off-by: Gautam <gautams@broadcom.com>
The new CONFIG_NO_RC4=y build option can be used to remove all internal
hostapd and wpa_supplicant uses of RC4. It should be noted that external
uses (e.g., within a TLS library) do not get disabled when doing this.
This removes capability of supporting WPA/TKIP, dynamic WEP keys with
IEEE 802.1X, WEP shared key authentication, and MSCHAPv2 password
changes.
Signed-off-by: Jouni Malinen <j@w1.fi>
FIPS builds do not include support for MD4/MD5, so disable
EAP-TTLS/CHAP, MSCHAP, and MSCHAPV2 when CONFIG_FIPS=y is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The OpenSSL internal AES_wrap_key() and AES_unwrap_key() functions are
unfortunately not available in FIPS mode. Trying to use them results in
"aes_misc.c(83): OpenSSL internal error, assertion failed: Low level API
call to cipher AES forbidden in FIPS mode!" and process termination.
Work around this by reverting commit
f19c907822 ('OpenSSL: Implement aes_wrap()
and aes_unwrap()') changes for CONFIG_FIPS=y case. In practice, this
ends up using the internal AES key wrap/unwrap implementation through
the OpenSSL EVP API which is available in FIPS mode. When CONFIG_FIPS=y
is not used, the OpenSSL AES_wrap_key()/AES_unwrap_key() API continues
to be used to minimize code size.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a callback function that can be used from the P2P module to
request the current preferred list of operating channels from the
driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver supports the preferred frequency list extension, use this
information from the driver when no explicitly configured preference
list (p2p_pref_chan) is present for P2P operating channel selection.
This commit adds this for GO Negotiation and Invitation use cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 983422088f ('nl80211: Add means to
query preferred channels') return success if no driver wrapper callback
was provided for fetching the preferred channel list. That is
problematic since the *num argument is not updated and uninitialized
freq_list could end up getting used with arbitrary frequency values. Fix
this by returning error in case the values were not available due to
driver wrapper not implementing the function. This matches the style
used in the driver_nl80211.c implementation for the case where the
driver does not support such fetch operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the QCA vendor specific nl80211 interface to query the preferred
frequency list from driver and add a new wpa_cli command to query this
information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Upon GO Negotiation completion, if the remote peer becomes GO, send a
hint event over QCA vendor specific interface to inform the driver of
the likely operating channel of the P2P GO.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add vendor command to pass SET setband command to the driver and read
the updated channel list from driver when this notification succeeds.
This allows the driver to update its internal channel lists based on
setband configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed when enabling TLSv1.2 support for EAP-FAST since the
SSL_export_keying_material() call does not support the needed parameters
for TLS PRF and the external-to-OpenSSL PRF needs to be used instead.
Signed-off-by: Jouni Malinen <j@w1.fi>
Report the feature capability on P2PS-PROV-START and P2PS-PROV-DONE
ctrl-iface events. A feature capability value is specified as
'feature_cap=<hex>' event parameter, where <val> is a hexadecimal
string of feature capability bytes in a PD Response frame.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add a parameter allowing to specify a value of Coordination
Protocol Transport to P2PS_PROVISION and P2PS_PROVISION_RESP commands.
Extend the p2ps_provision structure to contain cpt_priority and
cpt_mask properties and initialize them on a P2PS PD request command.
The format of the parameter:
cpt=<cpt>[:cpt]
where <cpt> is CPT name e.g. UDP or MAC. The CPT names are listed
according to their preferences to be used for a specific P2PS session.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add Coordination Transport Protocol parameter to P2P_SERVICE_ADD
asp command.
Extend p2ps_advertisement structure to contain CPT priorities
and a supported CPT bitmask.
The format of the new parameter:
cpt=<cpt>[:<cpt>]
where <cpt> is a name of the Coordination Protocol Transport.
This implementation supports two CPT names: UDP and MAC.
The order of specified CPTs defines their priorities where
the first one has the highest priority.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Do not allow wpa_s->fst to be replaced when processing FST-ATTACH
command for an interface that has already been attached.
Signed-off-by: Jouni Malinen <j@w1.fi>
Try to exit more quickly by avoiding execution of the action script for
any pending events if the process is requested to be killed. This may
help in avoiding hitting the two second SIGALRM workaround in eloop in
case some of the action scripts block for long period of time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This header file is needed to get struct fst_iface_cfg and struct
fst_wpa_obj defined. While it does currently get pulled in through
ap/hostapd.h and ap/ap_config.h, a more explicit inclusion may be a
cleaner option for future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new mechanism can be used to combine multiple periodic AP
(including P2P GO) task into a single eloop timeout to minimize number
of wakeups for the process. hostapd gets its own periodic caller and
wpa_supplicant uses the previously added timer to trigger these calls.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, one timeout per process (by default every 30 seconds) was
used P2P peer expiration and another per-interface timeout (every 10
seconds) was used to expire BSS entries. Merge these to a single
per-process timeout that triggers every 10 seconds to minimize number of
process wakeups due to periodic operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The caller is not expected to free or modify the value since this is
returning a reference to a buffer maintained by the upper layer.
Signed-off-by: Jouni Malinen <j@w1.fi>
This command allows network variables to be copied from one network to
another when the networks belong to different radios. This is similar to
the per-interface DUP_NETWORK command. On the global control interface,
the command syntax is as follows:
DUP_NETWORK <src ifname> <dst ifname> <src network id> <dst network id> <variable name>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit implements hostapd global control interface notifications
infrastructure. hostapd global control interface clients issue
ATTACH/DETACH commands to register and deregister with hostapd
correspondingly - the same way as for any other hostapd/wpa_supplicant
control interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new phase1 config parameter value tls_disable_tlsv1_0=1 can now be
used to disable use of TLSv1.0 for a network configuration. This can be
used to force a newer TLS version to be used. For example,
phase1="tls_disable_tlsv1_0=1 tls_disable_tlsv1_1=1" would indicate that
only TLS v1.2 is accepted.
Signed-off-by: Jouni Malinen <j@w1.fi>
A typo in wpa_scan_result_compar() caused wrong scan results sorting
(and wrong roaming decision). This fixes a copy-paste regression
introduced by commit a1b790eb9d ('Select
AP based on estimated maximum throughput').
Signed-off-by: Maital Hahn <maitalm@ti.com>
If a device may be an explicit GO, it adds the GO details in the PD
Request. First, we try to reuse an active GO. If it is not present, we
try to reuse a non-active persistent group. In the latter case, if a
dedicated P2P interface is needed, the intended address should be that
of the pending interface. However, the wpas_get_go_info() provided the
ssid->bssid address, which is the address of the P2P device. This might
result in an incorrect intended interface attribute in the PD Request in
case a separate group interface is used.
Fix this by setting group_iface variable to true only if a dedicated
interface should be used and set the attribute accordingly.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Validate the PD Response frame contents more thoroughly when it is used
for P2PS.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When persistent group is used and the peer is GO in this group,
intended interface attribute should be added to PD request/response.
Not doing so violates the spec.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
If after P2PS PD the device should become a GO it sends P2PS-PROV-DONE
event which contains the GO interface name. If the GO isn't running yet
the device may use pending interface name. However, when the GO is
started, pending interface name will be removed.
Fix the GO interface name in P2PS-PROV-DONE event by copying the
interface name instead of saving the pointer.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Call wpas_p2p_create_iface() instead of just checking p2p_no_group_iface
config value. Not doing so, resulted in an incorrect behavior when the
driver sets WPA_DRIVER_FLAGS_DEDICATED_P2P_DEVICE flag.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
The IPv4 header after the Ethernet header is not 32-bit aligned and the
previous version ended up accessing 32-bit members at misaligned
addresses.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 38279bdb35 ('D-Bus: Coding style
cleanup') handled the dbus_new_handlers.c change properly, but misplaced
the second 'const' in dbus_old_handlers.c in a way that resulted in
duplicated const rather than marking the actual value const.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new TEST_FAIL and GET_FAIL control interface commands can be used
similarly to the earlier TEST_ALLOC_FAIL/GET_ALLOC_FAIL design. The new
version is more generic framework allowing any function to be annotated
for failure testing with the TEST_FAIL() macro. This mechanism is only
available in builds with CONFIG_WPA_TRACE_BFD=y and
CONFIG_TESTING_OPTIONS=y. For other builds, the TEST_FAIL() macro is
defined to return 0 to allow the compiler to remove the test code from
normal production builds.
As the first test site, allow os_get_random() to be marked for failing
based on call backtrace.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not allow 40 MHz co-ex PRI/SEC switch to force us to change our PRI
channel if we have an existing connection on the selected PRI channel
since doing multi-channel concurrency is likely to cause more harm than
using different PRI/SEC selection in environment with multiple BSSes on
these two channels with mixed 20 MHz or PRI channel selection.
Signed-off-by: Jouni Malinen <j@w1.fi>
In p2p_find command line processing a loop searching for multiple
'seek=' parameters modifies cmd buffer adding '\0' terminators.
The 'freq=' parameter is handled after that and can be
lost if a 'freq=' follows 'seek=' in a command line.
Fix it by moving a handling of 'freq=' parameter to be processed
before 'seek=' handling loop.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
This provides more information to upper layer programs on what happens
with connection attempts in cases where the enabled networks are not
found in scan results.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
If BOARD_HOSTAPD_PRIVATE_LIB is not used on an Android build, we will
need to replace both the p2p functions *and* wpa_driver_nl80211_driver_cmd
in order to successfully link. Let's make the name more generic so it is
more obvious what it is used for.
Suggested-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Kevin Cernekee <cernekee@google.com>
This check explicitly for reflection attack and stops authentication
immediately if that is detected instead of continuing to the following
4-way handshake that would fail due to the attacker not knowing the key
from the SAE exchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
The variables here are unsigned and as such, cannot have a negative
value. Use == 0 instead of <= 0 to make this cleaner.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of a static analyzer warning. The actual value for
WpaGuiApp::w will be set after the constructor has returned, so this
value was not really used uninitialized.
Signed-off-by: Jouni Malinen <j@w1.fi>
These configuration parameters did not use matching printf format string
parameters (signed vs. unsigned). While these configuratin values are,
in practice, small unsigned integers, the implementation should use
matching types to write these.
Signed-off-by: Jouni Malinen <j@w1.fi>
The sae_groups parameter is zero terminated array, not -1 terminated, so
must check the value against <= 0 to break out from the loop.
Signed-off-by: Jouni Malinen <j@w1.fi>
As far as IEEE 802.11 standard is concerned, WEP is deprecated, but at
least in theory, allowed as a group cipher. This option is unlikely to
be deployed anywhere and to clean up the implementation, we might as
well remove all support for this combination.
Signed-off-by: Jouni Malinen <j@w1.fi>
Call the FT processing function directly instead of going through
wpa_supplicant_event() to process FT Authentication frame in SME case.
This allows parsing error to be used to trigger immediate failure for
the connection instead of trying to proceed to reassociation step that
cannot succeed.
Signed-off-by: Jouni Malinen <j@w1.fi>
In case of a network interface removal, check if the interface
was also the parent interface of the P2P Device dedicated interface.
If this is the case, then stop the P2P Device functionality, and
remove the P2P Device dedicated interface.
In case that the interface is added again and P2P Device
functionality can be enabled again, add a new P2P Device dedicated
interface and allow further P2P Device functionality.
In case that the P2P Device dedicated interface is re-created, the
original P2P Device configuration file is needed, so store it in
the global params (instead in the wpa_interface configuration).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
p2p_ctrl_group_add() takes care of various configuration options (such
as ht/vht) before calling wpas_p2p_group_add(), so use it (just like
when P2P_GROUP_ADD is called with additional params).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Parse each parameter individually and combine all the function calls.
This will allow further patch to call it with no parameters (currently
this might result in failure).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
wpas_p2p_get_ht40_mode() used blacklist approach (bw != BW20) to find
the relevant op_class, but didn't take into account other non-BW40
cases, like BW80, that had been added to the bw enum after the initial
implementation. Fix this by looking for the specific BW40 bw cases.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
This is equivalent to the P2P_REMOVE_CLIENT command on control
interface. This can be used to remove the specified client [as object
path or string format interface address] from all groups (operating and
persistent) from the local GO.
Argument(s): peer[object path] OR iface[string format MAC address]
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Signed-off-by: Jijo Jacob <jijo.jacob@samsung.com>
PBC overlap detection searches for another BSS with active PBC in the
BSS table. However, when a separate P2P interface is used, scan results
without P2P IE are not saved in the BSS table, so non-P2P BSS's with
active PBC will not be detected.
Fix this by iterating only the WPS AP array instead of the BSS table.
This is also more efficient since only WPS APs may have active PBC. This
also fixes hwsim test "grpform_pbc_overlap" when a dedicated P2P Device
is used.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Previously the wpa_s->parent interface was used, which is not
necessarily the P2P Device management interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Only the first seek=<service name> parameter was accepted from the
P2P_FIND command. Fix this to go through all seek parameters to
construct the list of service hash values to seek.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 4be9f27595 ('wpa_cli: Use eloop
during connection attempts in interactive mode') did not take into
account the needs for signal processing in action mode. eloop_run() was
not called in this case and the internal select() loop would block eloop
processing anyway and prevent clean shutdown. Fix this by using eloop
for action mode operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The control interface commands may include passwords or other private
key material, so clear it explicitly from memory as soon as the
temporary buffer is not needed anymore.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for a P2P group formation failure to result in a
concurrent station mode operation getting disconnected in the specific
error case where group interface addition fails after a successful GO
Negotiation. Fix this by skipping the wpas_p2p_group_delete() call in
this specific case since the group interface does not exists anymore at
the point wpas_group_formation_completed() gets called.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the RX frequency of the Probe Request frame is known, specify it when
sending the Probe Response frame. This is needed when the Probe Request
frame is received on another virtual interface, for example, when a GO
or P2PS client are discoverable on the group operating channel.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Change send_mlme() API to allow sending management frames on a specific
channel, overriding the internal driver decision.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
1. Add global p2p_cli_probe property to enable/disable Probe Request
frame RX reporting for connected P2P Clients. The property can be set to
0 - disable or 1 - enable. The default value is 0.
2. Enable Probe Request frame RX reporting for P2P Client on
WPA_COMPLETED state if p2p_cli_probe property is set to 1. Disable it
when an interface state is changing to any other state.
3. Don't cancel Probe Request frame RX reporting on wpa_stop_listen for
a connected P2P Client handling Probe Request frames.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
In some cases, Probe Request frames can be received by a peer not only
on a listen channel. In this case an additional rx_freq parameter
explitly contains a Probe Request frame RX frequency. In case rx_freq is
set to 0, a Probe Request frame RX channel is assumed to be our own
listen channel (p2p->cfg->channel).
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
It is possible for P2P_CONNECT-join command to be issued on a GO's P2P
Interface Address before the P2P peer entry is available to map this
into the GO's P2P Device Address. This could result in the join
operation failing to continue after receiving PD Response due to the
address mismatch (source address = P2P Device Address while only the P2P
Interface Address is known). Fix this by updating the pending join P2P
Device Address based on the BSS entry, if needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This has same behavior as the ctrl_iface RECONNECT command.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Add operating class 125 (channels 149..169) to the list of P2P supported
channels. This allows the 5 GHz channels 161 and 169 to be used for P2P
GO when those channels are allowed for AP mode in the current regulatory
domain.
Signed-off-by: Amr BEN ABDESSALEM <amrx.ben.abdessalem@intel.com>
Remove all gas-query radio works before calling gas_query_deinit()
as gas_query_deinit() flow frees the query context, which might
be later be accessed from the radio work callback (and result
with unexpected behavior, e.g., segmentation fault).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
ssid->p2p_persistent_group was left to its old value when changing a
network profile to/from P2P persistent group type (disabled=2). This
could result in unexpected behavior when using an incomplete persistent
group profile. This was mainly visible through D-Bus network profile
handling where a persistent group would not be unregistered insome
cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of an int variable with magic values 0, 1, 2, use an enum that
gives clearer meaning to the values now that the original boolean type
global argument is not really a boolean anymore.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes some issues where a disconnection event may get ignored if an
earlier operation to remove or disable a network resulted in an attempt
to disconnect event though no connection was in place.
wpa_s->current_ssid != NULL alone is not sufficient to determine that
there will be a driver event notifying completion of such disconnection
request. Set own_disconnect_req to 1 only if wpa_s->wpa_state is also
indicating that there is a connection or an attempt to complete one.
This showed up in a failure, e.g., when running the hwsim test case
scan_int followed by ap_vlan_wpa2_psk_radius_required where the latter
ended up not processing a connection failure event and getting stuck not
trying to run a new scan and connection attempt.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for Qt5 while still preserving support for building
with Qt4. The same source code builds with both Qt versions now. The
functionality should be identical.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Add GO Intent information of connecting device in GO Negotiation Request
event which will help applications to decide its own GO intent value in
advance and can avoid failure cases when both devices use GO Intent 15
depending on application requirement.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Support a request to scan specific SSIDs given by user with the SCAN
command. The SSID list can be suffixed to the scan command as follows.
For example, if SSIDs "ABC" and "abc123" need to be specifically
scanned, the command should be "SCAN ssid 414243 ssid 616263313233". The
value of the SSID is passed in hexadecimal representation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds a configurable parameter (wps_priority) to specify the
priority for the networks derived through WPS connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow the Manufacturer information for a found P2P peer device to be
fetched through the D-Bus interface similarly to p2p_peer <mac address>
on ctrl interface.
Signed-off-by: Amit Khatri <amit.khatri@samsung.com>
Signed-off-by: Rahul Jain <rahul.jain@samsung.com>
Signed-off-by: Ashutosh Kaushik <k.ashutosh@samsung.com>
Avoid memory leak due to previous allocation for ssid->ssid. It does not
look like this is hit in normal cases, but at might be possible for the
SSID to get set if the peer is present in previous scan results and WPS
code ends up copying the SSID from there.
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Add support to compile libwpa_client.so. This can be used by external
programs to interact with the wpa_supplicant control interface. Also
rename the static version of this library to libwpa_client.a to be
consistent with the name used previous in Android builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A new Invitation Request might be received on a just started persistent
group if the previous Invitation Response sent isn't received at the
peer (GO of the persistent group). When the peer sends an Invitation
Request again, treat it as start of group formation and restart the
group formation timer at this point of time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In the case of driver-based BSS selection, a bssid_hint in the connect
request might not result in to the selection of the same BSS. Thus,
postpone the updation of the wpa_s->current_bss till the association
event is received unless the BSSID is forced. This fixes issues where
wpa_s->current_bss may end up being updated to point to the BSS that
wpa_supplicant provided as a hint for a roaming case, but then not
restored if the driver decides to "return" to the current BSS instead.
This could result in some operations (e.g., WNM BSS TM response) not
working properly due to incorrect BSS being identified in
wpa_s->current_bss.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
D-Bus used the p2p_dev member in struct wpa_supplicant to track the
interface used for P2P Device operations. However, this is not needed as
the interface used for P2P Device operations is stored in struct
wpa_global->p2p_init_wpa_s.
Replace all the redirections to wpa_s->p2p_dev with redirections to
wpa_s->global->p2p_init_wpa_s and removed this member as it is no
longer needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This command is for a specific P2P group, not for the P2P Device
instance and as such, wpa_s pointer must not be replaced with the
interface that is used for P2P Device management.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The function used wpa_s->parent->conf to iterate the P2P networks and
update the configuration file. However, wpa_s->parent is not
necessarily the interface used to manage the P2P Device operations.
Fix this by accessing the configuration file of the interface
initialized to manage the P2P Device operations.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The function used wpa_s->parent->conf to iterate the P2P networks and
update the configuration file. However, wpa_s->parent is not
necessarily the interface used to manage the P2P Device operations.
Fix this by accessing the configuration file of the interface initialized
to managed the P2P Device operations.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
wpas_p2p_set_own_freq_preference() accessed wpa_s->parent->conf to test
if p2p_ignore_shared_freq is set, but wpa_s->parent is not necessarily
the interface used to manage the P2P Device operations.
Fix this by accessing the configuration file of the interface
initialized to manage the P2P Device operations.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
As wpas_p2p_remove_client() is not necessarily called from the interface
used to manage the P2P Device operations, when removing a client, use
the P2P management interface to iterate over the saved networks and
remove the relevant entries form the P2P GO network blocks.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Commit 1c2aa04c96 ('P2P: Do not add P2P
IEs on P2P disabled interface') removed the P2P IEs from association on
non-P2P interface. However, an AP functioning as a P2P manager needs the
cross connection capability of the station (P2P Device). This needs to
be done to meet the P2P specification requirements even if the station
interface has p2p_disabled=1 in case P2P in general is enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 5add410162 ('WPS: Use shorter
authentication timeout during no-SelReg iteration') broke the build with
WPS disabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
While being associated, if an ANQP request is received for a different
AP that doesn't exist in the BSS list, the ANQP request will be sent on
the frequency of the AP that we are currently associated to.
In such a case, it is possible that the ANQP request would be sent on
a channel different than that of the requested AP, potentially delaying
other requests/activities.
Avoid sending the ANQP request to an AP that is not in the BSS list.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Fix memory leak introduced in commit
32a097fdd2 ("wpa_cli: Keep track of
available networks") by tracking networks only when in interactive mode.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add the TDLS_LINK_STATUS command to the control interface. This command
shows what is the status of our current TDLS connection with the given
peer. Also, add the TDLS_LINK_STATUS command to wpa_cli.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Sanity check added to avoid segmentation fault which occurs, when
issuing ibss_rsn ctrl iface cmd and IBSS was not initialized previously
via IBSS network selection.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
Commit c2762e410f ('P2P: Update D-Bus
network object semantics during group formation') added this helper
function to determine whether a network block is used for storing a
persistent group information. However, it implemented this in a way that
matches both persistent group storage and an operating persist group
instance. This does not seem to match the expected behavior for the
D-Bus objects, so fix this to match only the persistent group storage
case to avoid registering/unregistered incorrect D-Bus objects for
groups.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit bb3df9a569 ('notify: Do not raise
any signal from a P2P management interface') was supposed to only change
D-Bus behavior, but it ended up disabling non-D-Bus functionality as
well for some sequences where the P2P Device interface is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 21efc940f6 ('wpa_supplicant: Do not
register a P2P management interface on DBus') hides the special P2P
management interface from D-Bus. However, it did not take into account
the possibility of wpa_s->dbus_path and wpa_s->dbus_new_path being NULL
in such cases on number of code paths within the D-Bus handlers. This
could result in invalid arguments (NULL path) being provided to D-Bus
functions (mainly, dbus_message_iter_append_basic) and NULL pointer
dereference when iterating over all interfaces. Either of these could
make wpa_supplicant process terminate.
Fix this by explicitly checking that the interface-specific D-Bus path
has been registered before using it anywhere with D-Bus handlers. In
addition, find the correct wpa_s instance to fix P2P operations through
D-Bus when the P2P Device interface is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Handling of WPS RF band for 60 GHz was missing. Add it in all relevant
places and also map "AES" as the cipher to GCMP instead of CCMP when
operating on the 60 GHz band.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Commit 5add410162 ('WPS: Use shorter
authentication timeout during no-SelReg iteration') added a new
condition on reducing the authentication timeout for the WPS AP
iteration process. However, due it ended up copy-pasting an incorrect
condition for this. This was supposed to apply for PIN-based config
method advertisement, not PBC.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, it was possible for the set_key() handler to be used with
WPA_ALG_PMK even if the driver did not indicate support for key
management offload. While this is not really supposed to result in any
difference, it makes the debug logs somewhat confusing. Avoid that by
using driver capability flag for key management offload as an additional
condition for setting the PMK.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
interworking_credentials_available_3gpp() would have left excluded2
uninitialized without INTERWORKING_3GPP in the build. This could result
in a static analyzer warning within
interworking_credentials_available_helper() about use of uninitialized
variable. Get rid of that warning by explicitly initializing excluded2
even though this does not really result in any difference in behavior
since the excluded2 value would be used only if the non-NULL is returned
and that could not have been the case here without INTERWORKING_3GPP.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for an nl80211-based driver to be determined to support
P2P even when the radio supports only the 5 GHz band. This resulted in
P2P initialization failing due to not being able to pick a social
channel and wpa_supplicant not starting. Fix this by not enabling P2P,
but still allowing wpa_supplicant initialization to complete.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signal strength meter uses non-standard icons (not included in the
freedesktop icon specification), which might not be available in all
icon sets on the market. What's more, according to the latest Ubuntu
practices, in the status-like places one should use symbolic icons.
Unfortunately not all icon sets provide them.
In order to overcome this inconsistency, we are going to try to load
more than one icon from the current theme in the fallback-like
fashion.
Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
When iterating through WPS APs that do not advertise Selected Registrar
TRUE, limit the authentication timeout to 10 seconds instead of the full
70 second value used with IEEE 802.1X/EAP/WPS in general. This helps
speed up AP iteration for cases where a selected AP misbehaves and does
not reply to EAP exchanges. This should not really be needed, but there
seems to be deployed APs that do not implement WPS correctly and with
such APs in the radio range, this extra timeout can speed up the
iteration to allow the correct AP to be found before the WPS operation
times out.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
