If hostapd or wpa_supplicant is built from a git repository, add a
VERSION_STR postfix from the current git branch state. This is from "git
describe --dirty=+". VERSION_STR will thus look something like
"2.6-devel-hostap_2_5-132-g4363c0d+" for development builds from a
modified repository.
This behavior is enabled automatically if a build within git repository
is detected (based on ../.git existing). This can be disabled with
CONFIG_NO_GITVER=y in wpa_supplicant/.config and hostapd/.config.
Signed-off-by: Jouni Malinen <j@w1.fi>
In addition to the PTK length increasing, the length of the PMK was
increased (from 256 to 384 bits) for the 00-0f-ac:12 AKM. This part was
missing from the initial implementation and a fixed length (256-bit) PMK
was used for all AKMs.
Fix this by adding more complete support for variable length PMK and use
384 bits from MSK instead of 256 bits when using this AKM. This is not
backwards compatible with the earlier implementations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Fix and extend the ieee80211_freq_to_channel_ext() function to deal
correctly with VHT operating classes (128, 129, 130).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Extended channel switch provides an ability to switch between operating
classes and is required for P2P Devices by the P2P specification when
switching in 5 GHz.
When the operating class is provided for channel switch, the AP/P2P GO
will use eCSA IE in addition to the regular CSA IE both on 2.4 GHz and 5
GHz bands.
Transitions between different hw_modes are not supported.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Introduce definitions for QCA vendor specific subcommands
and attributes to support vendor scan request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Split chown() call in wpa_ctrl_open() and wpa_ctrl_open2() to allow the
group id to be set even if the process does not have privileges to
change the owner. This is needed for modules that need to communicate
with wpa_supplicant since without the group change, wpa_supplicant may
not have privileges to send the response to a control interface command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new no_auth_if_seen_on=<ifname> parameter can now be used to
configure hostapd to reject authentication from a station that was seen
on another radio.
This can be used with enabled track_sta_max_num configuration on another
interface controlled by the same hostapd process to reject
authentication attempts from a station that has been detected to be
capable of operating on another band, e.g., to try to reduce likelihood
of the station selecting a 2.4 GHz BSS when the AP operates both a 2.4
GHz and 5 GHz BSS concurrently.
Note: Enabling this can cause connectivity issues and increase latency for
connecting with the AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows control interface monitors to get more detailed information
in cases where wpa_supplicant-based SME receives an Authentication frame
with non-zero status code.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a new helper function wpa_ctrl_open2() that can be used
instead of wpa_ctrl_open() to override the default client socket
directory. Add optional -s<directory path> argument to hostapd_cli and
wpa_cli to allow the client socket directory to be specified.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While the EAPOL-Key MIC derivation was already changed from SHA256 to
SHA384 for the Suite B 192-bit AKM, KDF had not been updated similarly.
Fix this by using HMAC-SHA384 instead of HMAC-SHA256 when deriving PTK
from PMK when using the Suite B 192-bit AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
This code path could not be hit with the RSNE generated by hostapd or
wpa_supplicant, but it is now possible to reach when using
own_ie_override test functionality. The RSNE and IE buffer length were
not updated correct in case wpa_insert_pmkid() had to add the RSN
Capabilities field.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add ieee80211_freq_to_channel_ext() conversion function into
ieee802_11_common.c. This function converts freq to channel and
additionally computes operating class, based on provided HT and VHT
parameters.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This adds parsing of QCA vendor specific elements and as the first such
element to be parsed, stores pointers to the preferred frequency list
element that can be used to enhance P2P channel negotiation behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new enum qca_vendor_element_id registry is used to manage
assignments of vendor specific elements using the QCA OUI 00:13:74. The
initial assignment is for the purpose for extending P2P functionality
for cases where the wpa_supplicant implementation is used by both ends
of an exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When ACS is offloaded to device driver and the hw_mode parameter is set
to any, the current_mode structure is NULL which fails the ACS command.
Fix this by populating the ACS channel list with channels from all bands
when current_mode is NULL.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add vendor command to pass SET setband command to the driver and read
the updated channel list from driver when this notification succeeds.
This allows the driver to update its internal channel lists based on
setband configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
On PD Request/follow-on PD Request preparation set a feature capability
CPT value of PD context.
On PD Request processing use a request CPT and service advertisement
CPT priority list to select a feature capability CPT of PD Response.
On follow-on PD Request processing use a request CPT and a CPT priority
list in PD context to select a CPT value of follow on PD Response.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add Coordination Transport Protocol parameter to P2P_SERVICE_ADD
asp command.
Extend p2ps_advertisement structure to contain CPT priorities
and a supported CPT bitmask.
The format of the new parameter:
cpt=<cpt>[:<cpt>]
where <cpt> is a name of the Coordination Protocol Transport.
This implementation supports two CPT names: UDP and MAC.
The order of specified CPTs defines their priorities where
the first one has the highest priority.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Introduce definitions for QCA vendor specific subcommands and attributes
to support multiport concurrency.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These are confusing when the style used with the couple of FST IE checks
differs from the rest of hostapd/wpa_supplicant implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Fast Session Transfer (FST) is the transfer of a session from a channel
to another channel in a different frequency band. The term "session"
refers to non-physical layer state information kept by a pair of
stations (STAs) that communicate directly (i.e., excludes forwarding).
The FST is implemented in accordance with IEEE Std 802.11ad-2012.
Definitions
* FST interface - an interface for which FST functionality is enabled
* FST group - a bunch of FST interfaces representing single
multi-band STA
* FST peer - a multi-band capable STA connected
* FST module - multi-band operation functionality implemented in
accordance with IEEE Std 802.11ad-2012 (see 10.32
Multi-band operation) as a part of hostapd/wpa_supplicant
* FST manager - an external application that implements custom FST
related logic, using the FST module's interfaces
accessible via CLI or D-Bus
This commit introduces only the FST module. Integration of the FST
module into the hostapd/wpa_supplicant and corresponding CLI/D-Bus
interfaces and FST related tests are covered in separate commits.
FST manager application is out of scope of these commits.
As FST aggregates a few interfaces into FST group, the FST module uses
global CLI for both commands and notifications. It also exposes
alternative non-interface based D-Bus subtree for this purposes.
Configuration and Initialization
* FST functionality can enabled by compilation flag (CONFIG_FST)
* hostapd/wpa_supplicant controlling multiple interfaces are used for
FST
* once enabled by compilation, the FST can be enabled for specific
interfaces in the configuration files
* FST interfaces are aggregated in FST groups (fst_group_id config file
entry), where each FST group:
- represents one multi-band device
- should have two or more FST interfaces in it
* priority (fst_priority config file entry) must be configured for each
FST interface. FST interface with higher priority is the interface FST
will always try to switch to. Thus, for example, for the maximal
throughput, it should be the fastest FST interface in the FST setup.
* default Link Loss Timeout (LLT) value can be configured for each FST
interface (fst_llt config file entry). It represents LLT to be used
by FST when this interface is active.
* FST interfaces advertise the Multi-band capability by including the
Multi-band element in the corresponding frames
FST CLI commands:
* fst list_groups - list FST groups configured.
* fst list_ifaces - list FST interfaces which belong to specific group
* fst iface_peers - list Multi-Band STAs connected to specific interface
* fst list_sessions - list existing FST sessions
* fst session_get - get FST session info
* fst session_add - create FST session object
* fst session_set - set FST session parameters (old_iface, new_iface,
peer_addr, llt)
* fst session_initiate - initiate FST setup
* fst session_respond - respond to FST setup establishemnt attempt by
counterpart
* fst session_transfer - initiate FST switch
* fst session_teardown - tear down FST Setup but leave the session object
for reuse
* fst session_remove - remove FST session object
FST CLI notifications:
* FST-EVENT-PEER - peer state changed (CONNECT/DISCONNECT)
* FST-EVENT-SESSION - FST session level notification with following
sub-events:
- EVENT_FST_SESSION_STATE - FST session state changed
- EVENT_FST_ESTABLISHED - previously initiated FST session became
established
- EVENT_FST_SETUP - new FST session object created due to FST session
negotiation attempt by counterpart
All the FST CLI commands and notifications are also implemented on D-Bus
for wpa_supplicant.
IEEE 802.11 standard compliance
FST module implements FST setup statemachine in compliance with IEEE
802.11ad (P802.11-REVmc/D3.3), as it described in 10.32 Multi-band
operation (see also Figure 10-34 - States of the FST setup protocol).
Thus, for example, the FST module initiates FST switch automatically
when FST setup becomes established with LLT=0 in accordance with
10.32.2.2 Transitioning between states.
At the moment, FST module only supports non-transparent STA-based FST
(see 10.32.1 General).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The FT-specific check for valid group cipher in wpa_ft_gen_req_ies() was
not up-to-date with the current list of supported ciphers. Fix this by
using a generic function to determine validity of the cipher. In
practice, this adds support for using CCMP-256 and GCMP-256 as the group
cipher with FT.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to have separate return statements for these corner
cases that are unlikely to be hit in practice.
Signed-off-by: Jouni Malinen <j@w1.fi>
The cwmin/cwmax parameters were limited more than is needed. Allow the
full range (0..15 for wmm_ac_??_{cwmin,cwmax} and 1..32767 for
tx_queue_data?_{cwmin,cwmax}) to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The current P802.11 description of SAE uses "1 < element < p" as the
required range. However, this is not correct and does not match the
Dragonfly description of "1 < element < p-1". SAE definition will need
to change here. Update the implementation to reject p-1 based on the
correct rule here.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2012 description of SAE does not require this, i.e., it
describes the requirement as 0 < scalar < r for processing the Commit
message. However, this is not correct and will be changes to 1 < scalar
< r to match the Dragonfly description so that a trivial secret case
will be avoided explicitly.
This is not much of an issue for the locally generated commit-scalar
since it would be very unlikely to get the value of 1. For Commit
message processing, a peer with knowledge of the password could
potentially force the exchange to expose key material without this
check.
Signed-off-by: Jouni Malinen <j@w1.fi>
This provides more information to upper layer programs on what happens
with connection attempts in cases where the enabled networks are not
found in scan results.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
If PWE is discovered before the minimum number of loops (k) is reached,
the extra iterations use a random "password" to further obfuscate the
cost of discovering PWE.
Signed-off-by: Jouni Malinen <j@w1.fi>
This replaces the earlier IEEE Std 802.11-2012 algorithm with the design
from P802.11-REVmc/D4.0. Things brings in a blinding technique for
determining whether the pwd-seed results in a suitable PWE value.
Signed-off-by: Jouni Malinen <j@w1.fi>
draft-irtf-cfrg-dragonfly recommends implementation to set the security
parameter, k, to a value of at least 40. This will make PWE generation
take significantly more resources, but makes it more likely to hide
timing differences due to different number of loops needed to find a
suitable PWE.
Signed-off-by: Jouni Malinen <j@w1.fi>
This check explicitly for reflection attack and stops authentication
immediately if that is detected instead of continuing to the following
4-way handshake that would fail due to the attacker not knowing the key
from the SAE exchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to have separate return statements for these corner
cases that are unlikely to be hit in practice.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to have a separate "fail silently" case for wpa_ie_len
== 0. That condition does not seem to be reachable and even if it were,
the following "ie len too short" case will result in the exact same
return value.
Signed-off-by: Jouni Malinen <j@w1.fi>
As far as IEEE 802.11 standard is concerned, WEP is deprecated, but at
least in theory, allowed as a group cipher. This option is unlikely to
be deployed anywhere and to clean up the implementation, we might as
well remove all support for this combination.
Signed-off-by: Jouni Malinen <j@w1.fi>
CA country code was included mistakenly (copy-paste..) in cn_op_class_cc
while it was supposed to be included only in us_op_class_cc. In
practice, this did not result in incorrect operation due to the
us_op_class_cc list being checked first. Anyway, better fix
cn_op_class_cc to avoid confusion here.
Signed-off-by: Jouni Malinen <j@w1.fi>
This increases code coverage for gas.c testing to cover areas that
cannot be reached with pure hwsim test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add operating class 125 (channels 149..169) to the list of P2P supported
channels. This allows the 5 GHz channels 161 and 169 to be used for P2P
GO when those channels are allowed for AP mode in the current regulatory
domain.
Signed-off-by: Amr BEN ABDESSALEM <amrx.ben.abdessalem@intel.com>
When device supports dual band operations with offloaded ACS, hw_mode
can now be set to any band (hw_mode=any) in order to allow ACS to select
the best channel from any band. After a channel is selected, the hw_mode
is updated for hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Link Property query vendor command shall facilitate the information
of the Wi-Fi link. MAC address of the Wi-Fi peer is given as an input
for querying the link properties.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Remove the length field from struct ieee802_11_elems since the only
allowed element length is five and that is checked by the parser.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the only allowed element length is one.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the only allowed element length is one.
Signed-off-by: Jouni Malinen <j@w1.fi>
All the existing users of these elements were already validating the
element length. However, it is clearer to validate this already at the
parser for extra layer of protection for any future changes.
Signed-off-by: Jouni Malinen <j@w1.fi>
This program can be used to run fuzzing tests for areas related to P2P
message parsing and processing. p2p-fuzzer allows data files to be used
to inject Probe Response and Action frames for processing by the P2P
module.
Signed-off-by: Jouni Malinen <j@w1.fi>
The SSID element is defined to have a valid length range of 0-32. While
this length was supposed to validated by the users of the element
parser, there are not really any valid cases where the maximum length of
32 octet SSID would be exceeded and as such, the parser itself can
enforce the limit as an additional protection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Both Android's libc and glibc support _FORTIFY_SOURCE, a compiler
and libc feature which inserts automatic bounds checking into
common C functions such as memcpy() and strcpy(). If a buffer
overflow occurs when calling a hardened libc function, the
automatic bounds checking will safely shutdown the program and
prevent memory corruption.
Android is experimenting with _FORTIFY_SOURCE=3, a new fortify
level which enhances memcpy() to prevent overflowing an element
of a struct. Under the enhancements, code such as
struct foo {
char empty[0];
char one[1];
char a[10];
char b[10];
};
int main() {
foo myfoo;
int n = atoi("11");
memcpy(myfoo.a, "01234567890123456789", n);
return 0;
}
will cleanly crash when the memcpy() call is made.
Fixup hostap code to support the new level. Specifically:
* Fixup sha1_transform so it works with the enhanced bounds checking.
The old memcpy() code was attempting to write to context.h0, but that
structure element is too small and the write was extending (by design)
into h1, h2, h3, and h4. Use explicit assignments instead of
overflowing the struct element.
* Modify most of the structures in ieee802_11_defs.h to use ISO C99
flexible array members (https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html)
instead of a zero length array. Zero length arrays have zero length,
and any attempt to call memcpy() on such elements will always overflow.
Flexible array members have no such limitation. The only element not
adjusted is probe_req, since doing so will generate a compile time error,
and it's not obvious to me how to fix it.
Signed-off-by: Nick Kralevich <nnk@google.com>
wpa_ctrl.c gets sys/stat.h inherited from
private/android_filesystem_config.h it should
not rely on this in the future. The intent is
to move fs_config function into libcutils and
thus deprecate any need for sys/stat.h in this
include file.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
The new network profile parameter mem_only_psk=1 can be used to specify
that the PSK/passphrase for that network is requested over the control
interface (ctrl_iface or D-Bus) similarly to the EAP network parameter
requests. The PSK/passphrase can then be configured temporarily in a way
that prevents it from getting stored to the configuration file.
For example:
Event:
CTRL-REQ-PSK_PASSPHRASE-0:PSK or passphrase needed for SSID test-wpa2-psk
Response:
CTRL-RSP-PSK_PASSPHRASE-0:"qwertyuiop"
Note: The response value uses the same encoding as the psk network
profile parameter, i.e., passphrase is within double quotation marks.
Signed-off-by: Jouni Malinen <j@w1.fi>
Old code defaulted to WEP for an AP advertising OSEN. Show as OSEN
instead. Re-use most of the RSN parsing logic since all but the header
is the same.
Example output:
[root@ath9k-f lanforge]# ./local/bin/wpa_cli -i sta0 scan_results
bssid / frequency / signal level / flags / ssid
00:0e:8e:6f:40:49 2462 -23 [OSEN-OSEN-CCMP][ESS] ben-138
Signed-off-by: Ben Greear <greearb@candelatech.com>
Update ACS driver offload feature for VHT configuration. In addition,
this allows the chanlist parameter to be used to specify which channels
are included as options for the offloaded ACS case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the AP/Authenticator receives an EAPOL-Key msg 2/4 for an association
that negotiated use of PSK and the EAPOL-Key MIC does not match, it is
likely that the station is trying to use incorrect PSK/passphrase.
Report this with "AP-STA-POSSIBLE-PSK-MISMATCH <STA addr>" control
interface event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Channel 140 is needed as allowed HT40 channel pair to use
channel 144 introduced in 802.11ac for VHT40 and VHT80.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Add handling logic for DFS offloaded case, and add a helper function
that takes the frequency (MHz) as a param and returns 1 if given channel
requires DFS, or 0 otherwise.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These values were previously used only for sorting the scan results, but
it may be useful to provide access to the used values through the BSS
entries.
Signed-off-by: Jouni Malinen <j@w1.fi>
When DFS offloading capability is supported by the driver, the driver
should use these events to indicate when a radar pattern has been
detected, channel availability check (CAC) has been completed, aborted
or finished after the non-occupancy period is over on a DFS channel.
Also, add a new driver.h event to be used by NL80211 to indicate CAC
Started event on a DFS channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When DFS offloading capability is supported by the driver, the driver
should use this event to indicate when channel availability check (CAC)
is started on a DFS channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds testing code (for CONFIG_TESTING_OPTIONS=y builds only) to
send an nl80211 vendor command and report a test vendor event in case
the driver supports this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Send MESH-SAE-AUTH-BLOCKED event if SAE authentication is blocked. The
BLOCK state will finish when a new peer notification event is sent for
the same MAC address.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
SAE authentication fails likely with wrong password. This commit adds a
notification of the failure to the upper application (UI) so that the
application can notify suspection of a wrong password to the user. The
control interface monitor even for this is "MESH-SAE-AUTH-FAILURE
addr=<peer>".
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This modifies struct wpa_ptk to allow the length of KCK and KEK to be
stored. This is needed to allow longer keys to be used, e.g., with
Suite B 192-bit level.
Signed-off-by: Jouni Malinen <j@w1.fi>
The ANQP verification/parsing is done only after the GAS_DONE indication
is sent over the control interface. This means that in case the ANQP
parsing fails there is no indication to the upper layers. Add an
ANQP-QUERY-DONE event that reports the status of the ANQP parsing.
Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
A new "CTRL-EVENT-EAP-PEER-ALT depth=<i> <alt name>" event is now used
to provide information about server certificate chain alternative
subject names for upper layers, e.g., to make it easier to configure
constraints on the server certificate. For example:
CTRL-EVENT-EAP-PEER-ALT depth=0 DNS:server.example.com
Currently, this includes DNS, EMAIL, and URI components from the
certificates. Similar information is priovided to D-Bus Certification
signal in the new altsubject argument which is a string array of these
items.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new VENDOR_ELEM value 13 can now be used to add a vendor element
into all (Re)Association Request frames, not just for P2P use cases like
the previous item was for.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
