When the list of preferred transition candidates is received, use the
identified channels to optimize the following scan so that no time is
wasted on other channels.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add the TSPEC to the driver on successful TSPEC ADDTS response. Delete
the TSPEC when receiving DELTS action.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Add basic implementation for ADDTS and DELTS sending
functions.
wpas_wmm_ac_addts() will send ADDTS request public action,
containing TSPEC (traffic stream specification) with
the given params.
wpas_wmm_ac_delts() will look for the saved tspec with
the given tid, and send DELTS public action for it.
(Handling of ADDTS response and actually configuring the admission
control params will be added in following patches.)
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Add add_tx_ts() and del_tx_ts() ops to notify the driver about
TSPEC add / delete.
Additionally, add wmm_ac_supported flag to indicate
whether the driver supports WMM AC.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Initialize WMM AC data structures upon successful association
with an AP that publishes WMM support, and deinitialize the data
structure when the association is no longer valid.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
It is possible for scan result processing or BSS entry removal to occur
while there is a pending connect or sme-connect radio work with a
previously selected BSS entry. The BSS pointer was previously verified
to be valid, i.e., still point to a BSS entry, at the time the actual
connection operation is started. However, that BSS entry could have
changed to point to another BSS if the old BSS entry was either removed
or reallocated and a new BSS entry was added at the same location in
memory. This could result in the connection attempt failing to configure
parameters properly due to different BSS information (e.g., different
BSSID).
Fix this by updated the pending connect radio work data on BSS entry
updates similarly to how the last_scan_res array was updated. If the
selected BSS entry is removed, this will still result in a failed
connection, but reallocated BSS entry is now followed properly and used
when the connection work starts.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This will be useful to hand-off P2P commands from the parent interface
to its dedicated P2P device if that one is present, in DBus interface.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Once a P2P GO interface is configured, save the group common
frequencies, as this can be useful later for channel selection
considerations during channel switch, etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The extra_roc_dur parameter can now be used in CONFIG_TESTING_OPTIONS=y
builds to simulate driver behavior where the ROC duration gets increased
without user space request.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add routines to (de)initialize mesh interface data structures and
join and leave mesh networks.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
Add smps_modes field, and let the driver fill it with its supported SMPS
modes (static/dynamic). This will let us start an AP with specific SMPS
mode (e.g., dynamic) that will allow it to reduce its power usage.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Commit 1595eb93ae ('P2P: Add support for
60 GHz social channel') had an unintended change to how P2P search scans
2.4 GHz social channels. Use of p2p_supported_freq() to filter the list
of social channels ended up using the disallow_freq setting to remove
social channels from the P2P search scans. This is not desired since
peers need to be found on any of the social channels even if those
channels have been disabled from P2P operating channel use. Restore the
previous behavior by included all the 2.4 GHz social channels in P2P
search scans if the driver indicated support for the 2.4 GHz band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is now possible to run hwsim_test like data connectivity test through
wpa_supplicant/hostapd control interface if CONFIG_TESTING_OPTIONS=y is
used for the build. Test functionality is enabled/disabled at runtime
with "DATA_TEST_CONFIG <1/0>". The "DATA_TEST_TX <dst> <src> <tos>"
command can be used to request a test frame to be transmitted.
"DATA-TEST-RX <dst> <src>" event is generated when the test frame is
received.
Signed-off-by: Jouni Malinen <j@w1.fi>
Convert the driver flags variable to u64 since there was no room for
more flags.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
This makes wpa_supplicant SME create PMKSA cache entries from SAE
authentication and try to use PMKSA caching if an entry is found for the
AP. If the AP rejects the attempt, fall back to SAE authentication is
used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new ext_eapol_frame_io parameter can be used to configure hostapd
and wpa_supplicant to use control interface for receiving and
transmitting EAPOL frames. This makes it easier to implement automated
test cases for protocol testing. This functionality is included only in
CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A P2P Client may be able to connect to the GO even if the WPS
provisioning step has not terminated cleanly (e.g., P2P Client does not
send WSC_Done). Such group formation attempt missed the event
notification about started group on the GO and also did not set the
internal state corresponding to the successful group formation.
This commit addresses the missing part by completing GO side group
formation on a successful first data connection if WPS does not complete
cleanly. Also, this commit reorders the STA authorization indications to
ensure that the group formation success notification is given prior to
the first STA connection to handle such scenarios.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the case of non-netdev P2P management device ended up
pulling in both the main interface (e.g., wlan0) and P2P Device
interface (from command line -m argument) as configuration. Similarly,
the main interface ended up included both configuration files. This is
not really helpful for various use cases, e.g., when permanent P2P group
information is stored in the P2P Devince interface, but it gets
duplicated in the main station interface configuration.
Clean this up by changing the -m<file> argument to replace, not
concatenate, configuration information. In other words, the main station
interface will not read this configuration and the P2P Device interface
(non-netdev) does not read parameters from the station interface
configuration file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
mac_addr=2 and preassoc_mac_addr=2 parameters can now be used to
configure random MAC address to be generated by maintaining the OUI part
of the permanent MAC address (but with locally administered bit set to
1). Other than that, these values result in similar behavior with
mac_addr=1 and preassoc_mac_addr=1, respectively.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds experimental support for wpa_supplicant to assign random local
MAC addresses for both pre-association cases (scan, GAS/ANQP) and for
connections. MAC address policy for each part can be controlled
separately and the connection part can be set per network block.
This requires support from the driver to allow local MAC address to be
changed if random address policy is enabled. It should also be noted
that number of drivers would not support concurrent operations (e.g.,
P2P and station association) with random addresses in use for one or
both.
This functionality can be controlled with the global configuration
parameters mac_addr and preassoc_mac_addr which set the default MAC
address policies for connections and pre-association operations (scan
and GAS/ANQP while not connected). The global rand_addr_lifetime
parameter can be used to set the lifetime of a random MAC address in
seconds (default: 60 seconds). This is used to avoid unnecessarily
frequent MAC address changes since those are likely to result in driver
clearing most of its state. It should be noted that the random MAC
address does not expire during an ESS connection, i.e., this lifetime is
only for the case where the device is disconnected.
The mac_addr parameter can also be set in the network blocks to define
different behavior per network. For example, the global mac_addr=1 and
preassoc_mac_addr=1 settings and mac_addr=0 in a home network profile
would result in behavior where all scanning is performed using a random
MAC address while connections to new networks (e.g.,
Interworking/Hotspot 2.0) would use random address and connections to
the home network would use the permanent MAC address.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some deployed APs send two credentials when in mixed-WPA/WPA2
configuration; one for the WPA-Personal/TKIP and the other for
WPA2-Personal/CCMP. Previously, this would result in two network blocks
getting added for the single AP. This can be somewhat confusing and
unnecessary, so merge such credentials into a single one that allows
both WPA and WPA2 to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds following new control interface commands to allow arbitrary
vendor elements to be added into number of frames:
VENDOR_ELEM_ADD <frame id> <hexdump of elem(s)>
VENDOR_ELEM_GET <frame id>
VENDOR_ELEM_REMOVE <frame id> <hexdump of elem(s)>
VENDOR_ELEM_REMOVE <frame id> *
The following frames are supported in this commit (additional frames can
be added in the future):
0 = Probe Request frame in P2P device discovery
1 = Probe Response frame from P2P Device role
2 = Probe Response frame from P2P GO
3 = Beacon frame from P2P GO
4 = PD Req
5 = PD Resp
6 = GO Neg Req
7 = GO Neg Resp
8 = GO Neg Conf
9 = Invitation Request
10 = Invitation Response
11 = P2P Association Request
12 = P2P Association Response
One or more vendor element can be added/removed with the commands. The
hexdump of the element(s) needs to contain the full element (id, len,
payload) and the buffer needs to pass IE parsing requirements to be
accepted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new "scan_id=<comma separated list of network ids>" parameter can
now be used to specify a list of network ids that have scan_ssid=1 to
indicate active scanning of the SSID. This adds the listed SSIDs to the
scan command to allow manual scan requests to perform active scans for
hidden SSIDs. For example, "SCAN scan_id=1,7,11" would run a scan with
the SSID fetched from the configured network blocks 1, 7, and 11
(assuming those are set with scan_ssid=1). The SSIDs will be included
even from network blocks that are currently disabled.
The maximum number of SSIDs added to the request is limited by the
driver support. If more than supported values are specified, the command
will fail (returns "FAIL").
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to trigger new SA Query procedure to check the state of
the connection immediately after having performed such a check. Limit
the impact of burst of unprotected Deauth/Disassoc frames by starting a
new SA Query procedure only once at least 10 seconds has passed from the
previous SA Query that was triggered by reception of an unprotected
disconnection. The first SA Query procedure for each association does
not follow this rule to avoid issues with test cases that expect to see
an SA Query every time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When the number of frequencies supported by the kernel is bigger than
one, and there is a need to pick a frequency for a new flow such as P2P
GO Negotiation or P2P Invitation, the flow should be able to pick the
best frequency among all the frequencies currently used by the device.
In order to prioritize between the currently used frequencies, add
the ability to collect additional data about each used frequency
(if the frequency is used by a station interface or P2P Client)
and when needed select the best frequency, where:
1. Infrastructure interfaces have highest priority
2. P2P Client interfaces have higher priority over AP/GO
interfaces.
The rational is that the frequency of an AP/GO can change while
that of a station interface cannot.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Prepare for new extended capabilities bits by checking that the local
buffer is large enough to contain all the bits the driver requests. The
existing buffers are large enough to include anything defined until now,
but it would be possible to add more definitions in the future, so
increase them a bit as well to make this more future proof.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the offchannel TX frame command was offloaded to the driver in
offchannel_send_action(), we must not send another copy of the frame if
a remain-on-channel event happens to be delivered between this TX
command and the matching TX status event. It was possible for the
duplicated frame to cause problems, e.g., with P2P invitation exchange
if the same Invitation Request frame got sent twice and only the first
one getting accepted by the peer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Scan for GO on the negotiated operating channel for few iterations
before searching on all the supported channels during persistent group
reinvocation. In addition, use the already known SSID of the group in
the scans. These optimizations reduce group formation time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add "reattach" command to perform single-channel single-ssid scan
instead of full scan when trying to reconnect to the currently
"connected" network (assuming old scan results are not current enough to
skip the scan completely). This allows the scan result to come back in
much faster time. In ath9k, the scan took around 12 seconds with full
background scan, and only 0.1 second with the single-channel single-ssid
scan. Thus, take much less time for the client to re-establish
connection with the currently "connected" network.
Signed-hostap: Peter Qiu <zqiu@chromium.org>
This enables more convenient protocol testing of AP and P2P
functionality in various error cases and unexpected sequences without
having to implement each test scenario within wpa_supplicant.
ext_mgmt_frame_handle parameter can be set to 1 to move all management
frame processing into an external program through control interface
events (MGMT-RX and MGMT-TX-STATUS) and command (MGMT_TX). This is
similar to the test interface that was added to hostapd previously, but
allows more control on offchannel operations and more direct integration
with the internal P2P module.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add an option to specify a configuration file that can be used to hold
the P2P_DEVICE configuration parameters. If this option is not used, the
P2P_DEVICE configuration parameters will be read from interface
configuration file.
Note that it is advised to use this option in some cases such as:
If a P2P_DEVICE is supported by the driver, the wpa_supplicant creates a
dedicated P2P Device interface, where the configuration file used for
the main interface is used. As a consequence, if the configuration file
includes network definition etc., the wpa_supplicant will try to perform
station specific flows on the P2P Device interface which will fail.
If a P2P_DEVICE is supported by the driver and update_config is used,
the P2P Device configuration data will override the main interface
configuration data.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Scan operation is not that reliable, so try couple of times if no
OSU provider matches are found during fetch_osu command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_cli fetch_osu command can be used to fetch information about
all OSU providers and write that to a text file with the icons in
separate files. cancel_osu_fetch command can be used to stop ongoing OSU
provider list fetch.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, any network block could be used to select the BSS to connect
to when processing scan results after Interworking network selection.
This can result in somewhat unexpected network selection in cases where
credential preferences indicated that a specific network was selected,
but another network ended up getting used for the connection. While the
older networks continue to be valid, add special processing for this
initial post-interworking-connect case to get more consistent network
selection to match with the Interworking network selection result.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the connect or sme-connect radio work to get
re-scheduled while an earlier request was still pending, e.g.,
select_network is issued at the moment a scan radio work is in progress
and the old scan results are recent enough for starting the connection.
This could result in unexpected attempt to re-associate immediately
after completing the first connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While testing rfkill blocking of a scanning interface, it
was seen that the ongoing scan never completes. This happens
since EVENT_SCAN_RESULTS is discarded on a disabled interface.
Fix this and also other possible radio work completion issues
by removing all the radio works (including started) of the
disabled interface.
To be able to remove already started radio works, make their
callbacks be reentrant with deinit flag (when the work
is started), so each radio work should be able to handle
its own termination.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Commit bd3a373767 added a mechanism to use
AP Channel attribute from within a Credential attribute to optimize
scans. However, this design is not actually used with the WPS NFC use
cases. With configuration token, the AP Channel attribute is in the same
container with the Credential attribute (and that was also handled in
the previous implementation). With connection handover, AP Channel
information is outside the Credential attribute as well.
Simplify implementation by removing the AP Channel within Credential
case. This allows wpas_wps_use_cred() to get the AP Channel from the
container instead of having to find this during credential iteration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This new mechanism allows P2P Client to request an IPv4 address from the
GO as part of the 4-way handshake to avoid use of DHCP exchange after
4-way handshake. If the new mechanism is used, the assigned IP address
is shown in the P2P-GROUP-STARTED event on the client side with
following new parameters: ip_addr, ip_mask, go_ip_addr. The assigned IP
address is included in the AP-STA-CONNECTED event on the GO side as a
new ip_addr parameter. The IP address is valid for the duration of the
association.
The IP address pool for this new mechanism is configured as global
wpa_supplicant configuration file parameters ip_addr_go, ip_addr_mask,
ip_addr_star, ip_addr_end. For example:
ip_addr_go=192.168.42.1
ip_addr_mask=255.255.255.0
ip_addr_start=192.168.42.2
ip_addr_end=192.168.42.100
DHCP mechanism is expected to be enabled at the same time to support P2P
Devices that do not use the new mechanism. The easiest way of managing
the IP addresses is by splitting the IP address range into two parts and
assign a separate range for wpa_supplicant and DHCP server.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The device with the NFC Tag can be configured to enable NFC to be used
with "P2P_SET nfc_tag 1" and "P2P_LISTEN" commands to allow static
handover to be used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"NFC_REPORT_HANDOVER {INIT,RESP} P2P <req> <sel>" can now be used to
report completed NFC negotiated connection handover in which the P2P
alternative carrier was selected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a QCA vendor specific nl80211 event to allow the driver to
indicate a list of frequency ranges that should be avoided due to
interference or possible known co-existance constraints. Such
frequencies are marked as not allowed for P2P use to force groups to be
formed on different channels.
If a P2P GO is operating on a channel that the driver recommended not to
use, a notification about this is sent on the control interface and
upper layer code may decide to tear down the group and optionally
restart it on another channel. As a TODO item, this could also be changed
to use CSA to avoid removing the group.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When start PNO request comes from control interface, wpa_supplicant
should wait until ongoing sched_scan (triggered by wpa_supplicant)
gets cancelled. Issuing cancel sched_scan and start PNO scan
one after another from pno_start() would lead wpa_supplicant to clear
wps->sched_scanning flag while getting sched_scan stopped event
from driver for cancel sched_scan request. In fact, PNO scan will
be in progress in driver and wpa_s->sched_scanning will not be set
in such cases.
In addition to this change, RSSI threshold limit is passed as part of
start sched_scan request. This was previously set only in pno_start(),
but the same parameter should be available for generic sched_scan calls
as well and this can now be reached through the new PNO start sequence.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If we already know the SSID of the P2P group we are trying to join, use
that SSID to limit scan responses and BSS selection since we do not
really look for any other network in this case. In addition, this can
fix cases where the peer has just changed its SSID (e.g., started a new
group) and there may be multiple BSS entries for the same BSSID.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some EAP methods can go through a step that is expected to fail and as
such, should not trigger temporary network disabling when processing
EAP-Failure or deauthentication. EAP-WSC for WPS was already handled as
a special case, but similar behavior is needed for EAP-FAST with
unauthenticated provisioning.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need to wait for the 15 second group formation timeout to
clear the state if WPS failure is detected during P2P group formation.
Allow the WPS exchange steps (WSC_NACK and EAP-Failure) to be completed
and remove the group to get rid of the extra wait.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, only the last response data was kept in memory. This
increases that to hold up to two last responses to allow some more
parallel operations to be requested. In addition, the response data is
now freed as soon as the external program has fetched it.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new control interface command RADIO_WORK can be used by external
programs to request radio allocation slots from wpa_supplicant if
exclusive radio control is needed, e.g., for offchannel operations. If
such operations are done directly to the driver, wpa_supplicant may not
have enough information to avoid conflicting operations. This new
command can be used to provide enough information and radio scheduling
to avoid issues with such cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
If an external program triggers a scan, wpa_supplicant does not have a
wpa_radio work item for this operation to protect against other
offchannel operations. This can result in operations failing, so try to
avoid damage by not starting any new wpa_radio work items during a scan
that was started by another process.
Signed-hostap: Jouni Malinen <j@w1.fi>
This type of protection against concurrent connection and scan
operations is now enforced through the wpa_radio work mechanism, so this
separate protection mechanism is not needed anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
Avoid concurrent P2P Listen operations with any other exclusive use of
the radio by using the radio work queuing mechanism. This removes some
of the earlier workarounds that postponed scans depending on other
operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
Avoid concurrent P2P scan requests with any other exclusive use of the
radio by using the radio work queuing mechanism. This removes some of
the earlier workarounds that postponed scans depending on other
operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new radio work item concept can be used to request time for an
operation that requires exclusive radio control, e.g., a scan. Once the
radio is available, the registered callback function will be called.
radio_work_done() must be called once the exclusive radio operation has
been completed, so that the radio is freed for other operations. The
special case of deinit=1 is used to free the context data during
interface removal. That does not allow the callback function to start
the radio operation, i.e., it needs to free the allocated resources
and return.
Signed-hostap: Jouni Malinen <j@w1.fi>
Track set_key operations per-key index and clear keys on disconnection
only if the key was set (or may have been set which is the case for the
first operation after wpa_supplicant start).
Signed-hostap: Jouni Malinen <j@w1.fi>
If the BSS table within wpa_supplicant is flushed, request the driver to
flush its own scan result table during the next scan. This can avoid
unexpected old BSS entries showing up after BSS_FLUSH or FLUSH command
in cases where the driver may maintain its internal cache of scan
results (e.g., cfg80211 BSS table persists at least for 15 seconds).
In addition to doing this automatically on BSS_FLUSH/FLUSH, a new SCAN
command argument, only_new=1, can be used to request a manual scan
request to do same. Though, it should be noted that this maintains the
BSS table within wpa_supplicant. BSS_FLUSH followed by SCAN command can
be used to clear all BSS entries from both the driver and
wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
The P2P_PRESENCE_REQ command did not give any easily available
indication of the response received from the GO. Make this more useful
by providing such response (if received) as a ctrl_iface monitor event
(P2P-PRESENCE-RESPONSE).
Signed-hostap: Jouni Malinen <j@w1.fi>
WPA_CIPHER_* and CIPHER_* are used for the exact same set of cipher
suites with the main difference being that the WPA_CIPHER_* version is
suitable to be used as a bitfield. Similarly, WPA_KEY_MGMT_* and
KEY_MGMT_* have similar design for AKMs. There is no need to maintain
two separate copies of the definitions since the bitfield compatible
version can be used for both needs. Get rid of the CIPHER_* and
KEY_MGMT_* versions to clean up the implementation by getting rid of
unnecessary mapping functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows users of wpa_supplicant control interface to figure out when
their specific scan command has been started and completed. For example:
CTRL-EVENT-SCAN-STARTED
> scan freq=2412,2417 passive=1 use_id=1
3
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-STARTED id=3
CTRL-EVENT-SCAN-RESULTS id=3
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows external programs to request wpa_supplicant to execute
a passive scan (i.e., do not send any Probe Request frames).
Signed-hostap: Jouni Malinen <j@w1.fi>
This parameter was not really used for anything else apart from a debug
message in the same function that set it. In addition, cfg80211 returns
the set of scanned frequencies even for the full scan, so the code that
was setting this conditionally on frequency list not being there was not
really ever entered either.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new freq=<frequency ranges> parameter to the SCAN command can be
used to request a scan to be performed on the specified set of channels
instead of on all channels. For example, "wpa_cli scan
freq=2400-2500,5180" would scan channels 1-14 and 36. Only the channels
that the driver indicates as enabled and that are within the specified
ranges are included in the request.
Signed-hostap: Jouni Malinen <j@w1.fi>
This just serves to check if there was a scan within
the last 5 seconds, hence it should use monotonic time.
While at it, also use os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This is only used for a debug message, but that message prints
the time since the last attempt, so it should use monotonic
time instead of wall clock.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The MMIC failure code should use monotonic time to check
whether 60 seconds have elapsed or not. For type-safety,
use struct os_reltime for the timestamp variable, and
also convert to using os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
GO activation can fail if the first client doesn't connect
within a certain time, but this should not be dependent on
wall time -- use monotonic time instead.
While at it, use os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The EAPOL RX workaround checks that the events are less than 100 ms
apart, so only uses relative times and should use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The BSS table, scan timeout, and related functionality should use
monotonic time since they care about relative values (age) only.
Unfortunately, these are all connected, so the patch can't be split
further. Another problem with this is that it changes the driver wrapper
API. Though, it seems only the test driver is using this.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The SA query timeout is just a regular timeout (currently
hard-coded to 1000 TU), so use monotonic time for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
struct wpa_radio is used as a shared data structure between all struct
wpa_supplicant instances that share the same physical radio.
Signed-hostap: Jouni Malinen <j@w1.fi>
On scan results event if a concurrent P2P scan was triggered previously,
scan results processing is canceled, p2p_find executed, and a new sta
scan is triggered (pending scan). However, this new sta scan does not
restore the scan_req value of the previous scan (whose scan result has
been canceled).
If we are currently connected to an AP and use ap_scan=2, the new
triggered scan will cause an associtation-without-scan in
wpa_supplicant_scan:
(ap_scan == 2 & scan_req != MANUAL_SCAN_REQ)
=> wpa_supplicant_assoc_try()
causing an association error and a disconnection.
This patch fixes this issue by restoring the previous scan_req value.
Signed-off-by: Loic Poulain <loicx.poulain@intel.com>
This prints out get_shared_radio_freqs() results and related information
from P2P operations to make debug logs more helpful for figuring out
issues related to multi-channel concurrency.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add the option to ask for VHT operation similarly to the way ht40 is
configured - either by adding 'vht' param to the relevant p2p_*
commands or by configuring p2p_go_vht=1 in the configuration file.
This patch only adds the configuration option (e.g., via control
interface). The actual handling of the VHT parameter (asking the driver
to use VHT, etc.) will be done by the following patch.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Offchannel operations needed for a GAS query can conflict with ongoing
scan/connection progress, so delay GAS queries if such an operation is
in progress on the current interface or any virtual interface sharing
the same radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, GO considered the group to be fully re-invoked after
starting beaconing on successful invitation exchange. This would leave
the group running until idle timeout (which may not be enabled) or
explicit removal if the client fails to connect for any reason. Since
the client is expected to connect immediately after the invitation
exchange that ends with status=0 (i.e., either client initiated the
exchange or it responded with success), extend group formation timeout
to cover that period until the first successfully completed data
connection. This allows the GO to remove the group automatically if the
client devices does not connect within
P2P_MAX_INITIAL_CONN_WAIT_GO_REINVOKE (15) seconds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, GO considered the group to be fully formed at the completed
of WPS provisioning step. This would leave the group running until idle
timeout (which may not be enabled) or explicit removal if the client
fails to connect for any reason. Since the client is expected to connect
immediately after the WPS provisioning step, extend group formation
timeout to cover that period until the first successfully completed data
connection. This allows the GO to remove the group automatically if the
client devices does not connect within P2P_MAX_INITIAL_CONN_WAIT_GO (10)
seconds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the GO of a persistent group to change the PSK or
remove a client when per-client PSKs are used and this can happen
without the SSID changing (i.e., the group is still valid, but just not
for a specific client). If the client side of such persistent group ends
up trying to use an invalidated persistent group information, the
connection will fail in 4-way handshake. A new WPS provisioning step is
needed to recover from this.
Detect this type of case based on two 4-way handshake failures when
acting as a P2P client in a persistent group. A new
"P2P-PERSISTENT-PSK-FAIL id=<persistent group id>" event is used to
indicate when this happens. This makes it easier for upper layers to
remove the persistent group information with "REMOVE_NETWORK <persistent
group id>" if desired (e.g., based on user confirmation).
In addition to indicating the error cases for persistent groups, all
this type of PSK failures end up in the client removing the group with
the new reason=PSK_FAILURE information in the P2P-GROUP-REMOVED event.
Signed-hostap: Jouni Malinen <j@w1.fi>
Record all generated per-client PSKs in the persistent group network
block and configure these for the GO Authenticator whenever re-starting
the persistent group. This completes per-client PSK support for
persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
"wpa_cli p2p_set per_sta_psk <0/1>" can now be used to disable/enable
use of per-device PSKs in P2P groups. This is disabled by default.
When enabled, a default passphrase is still generated by the GO for
legacy stations, but all P2P and non-P2P devices using WPS will get
a unique PSK.
This gives more protection for the P2P group by preventing clients from
being able to derive the unicast keys used by other clients. This is
also a step towards allowing specific clients to be removed from a group
reliably without having to tear down the full group to do so.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, concurrent station mode scans were postponed during an
ongoing P2P group formation up to the point of completed WPS
provisioning step. This would allow a scan to be started before the P2P
client has completed association for the data connection if a scan
request were timed to hit the window between the provisioning step and
the following association. Avoid this by extending P2P-in-progress state
to continue until the first data connection has been completed as part
of group formation. Use a ten second timeout for this to avoid leaving
scans disabled indefinitely if the client fails to connect completely.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There are devices that can operate several channels concurrently.
Change shared_vif_oper_freq() to get_shared_radio_freqs() that can
return an array of frequencies currently used by all the virtual
interfaces that share the same radio.
In addition, move it to wpa_supplicant.c, so it can be used by other
modules.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
Previously, drivers only reported if they support multiple concurrent
channels, but did not report the maximum number of supported channels.
Add this reporting to the driver capabilities and add the implementation
to driver_nl80211.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
If the capability flag of the driver indicates a dedicated P2P Device is
supported, a P2P Device interface is created.
Create the P2P Device in main interface creation loop when the added
interface flags support and P2P supplicant is not yet initialized
avoiding recursion of add_interface.
Do not register l2_packet for P2P Device interface (both for EAPOL and
for TDLS).
Signed-hostap: Arend van Spriel <arend@broadcom.com>
