Add a QCA vendor attribute to enable/disable the Punctured Preamble Rx
support in HE PHY capabilities.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver to disable data and
management response frame transmission to test the BSS max idle period
feature.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver/firmware to use only
RU 242 tone for data frame transmission.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver with a specific BSS
max idle period value to advertise in (Re)Association Request frames.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add additional attributes for the QCA vendor command
QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO to get finer details on roaming
behavior, TSF out of sync count, and the latest TX rate, Rate Index used
for the transmission.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The response for the respective TWT operations can either be synchronous
or asynchronous (wherever specified). If synchronous, the response to
this operation is obtained in the corresponding vendor command reply to
the user space. For asynchronous case, the response is obtained as an
event with the same operation type.
Drivers shall support either of these modes but not both simultaneously.
The support for asynchronous mode is advertised through the new flag
QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT. If the driver does not
include this flag, it shall support synchronous mode.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the following additional TWT operations:
QCA_WLAN_TWT_GET_STATS, QCA_WLAN_TWT_CLEAR_STATS,
QCA_WLAN_TWT_GET_CAPABILITIES, QCA_WLAN_TWT_SETUP_READY_NOTIFY.
Also define new attributes to qca_wlan_vendor_attr_twt_setup
and qca_wlan_vendor_attr_twt_nudge.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define QCA vendor attributes to dynamically configure TX NSS and RX NSS
to be used with QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION commands.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
TWT nudge is a combination of suspend and resume in a single request.
Add TWT nudge operation and QCA vendor attributes to support
the TWT nudge request.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduces a vendor specific feature capability
QCA_WLAN_VENDOR_FEATURE_CONCURRENT_BAND_SESSIONS to know if the device
supports concurrent network sessions on different Wi-Fi bands. This feature
capability is attributed to the hardware's capability to support the same
(e.g., DBS).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FULL_BW_UL_MU_MIMO to
enable/disable full bandwidth UL MU-MIMO subfield in the HE PHY
capabilities information field for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The connection process fails for several reasons and the status codes
defined in IEEE Std 802.11 do not cover the locally generated reason
codes. Add an attribute to QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO vendor
sub command which can be used by the driver/firmware to report various
additional reason codes for connection failures.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME_TRIGGERS that represents the
triggers for which the scan scheme from enum qca_roam_scan_scheme has to
be applied.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The firmware sends a new status code to indicate an already suspended
TWT session. Update the status code enum to represent this state.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add additional attributes to enum qca_vendor_attr_roam_control to
control the roam behavior through QCA_NL80211_VENDOR_SUBCMD_ROAM and
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new QCA vendor attributes to get thermal level from the driver. The
driver may return thermal level when userpace requests, or send a
thermal event when thermal level changes.
Signed-off-by: Hu Wang <huw@codeaurora.org>
This change adds QCA_NL80211_VENDOR_SUBCMD_MBSSID_TX_VDEV_STATUS,
and enum for qca_wlan_vendor_attr_mbssid_tx_vdev_status to notify
Tx VDEV status.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new vendor attribute for GPIO configuration. In addition, document
the previously defined attributes.
Signed-off-by: Chaoli Zhou <zchaoli@codeaurora.org>
Firmware statistics are received in the driver as opaque data. The host
target needs to send this opaque data to userspace wifistats
application. This new event is used to transfer this opaque data to the
application.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new QCA vendor attribute to configure the driver/firmware to
ignore SA Query timeout. If this configuration is enabled the
driver/firmware shall not send Deauthentication frame when SA Query
times out. This is required to support STA testbed role.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
These vendor attributes for FT/OCV/SAE testing can be configured only
when the STA is in connected state. Update the documentation of the
attributes to reflect the same.
Fixes: 18f3f99ac4 ("Add vendor attributes to configure testing functionality for FT/OCV/SAE")
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add support to get number of MIC errors, missing MME incidents, and
packet replay incidents observed while using IGTK/BIGTK keys when PMF
and/or beacon protection features are enabled.
These counters are applicable only for STA mode and can be fetched
through the QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO vendor command.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add a QCA vendor subcommand QCA_NL80211_VENDOR_SUBCMD_UPDATE_SSID
to update the new SSID in hostapd. NL80211_ATTR_SSID is used to encapsulate
the new SSID.
Signed-off-by: Pooventhiran G <pooventh@codeaurora.org>
Currently the driver/firmware indicates CCA busy time which includes own
TX and RX time and as such, does not allow the CCA busy time due to
other nodes to be computed. Add separate statistics to indicate own
radio TX time and own radio RX time to facilitate userspace applications
to compute CCA busy time because of traffic unintended to this device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
All QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* attributes are also nested
within QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO, not only
QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO* attributes in the current
implementation. Fix QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO documentation
accordingly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit does the following enhancements to the TWT interface:
Corrects the documentation for QCA_WLAN_TWT_SUSPEND and
QCA_WLAN_TWT_TERMINATE. Specifies that these operations carry the
parameters obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. This
interface is very recently introduced and missed to document the same.
There are no user space or driver components using this interface yet.
Hence, enhancing/modifying the interface.
Corrects the documentation for
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION. Mentions that the units it
represent is a multiple of 256 microseconds rather than a TU. The host
driver always interpreted this as an unit in 256 microseconds and there
are no user space implementations that are impacted with this change in
the unit. Hence, modifying the documentation.
Introduces QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT2_TWT_SIZE, which is
similar to that of QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT, but carries
an offset/data of u32 size.
Introduces MAC_ADDR attribute to represent the peer for the TWT setup
and resume operations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support to configure the number of TX chains and the number of RX
chains to be used during a connection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce additional attributes for the TWT response parameters from the
host driver. Also, add ATTR_TWT_RESUME_FLOW_ID for TWT Resume request.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The documentation for the QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE
attribute had incorrectly specified the value of 0 (corresponding to BE)
to disable the QoS upgrade. BK (1) is a lower priority AC compared to BE
and if BE is used to disable the upgrade, there would be no possibility
for configured UDP AC upgrade to replace BK-from-DSCP with BE. Thus,
correct this by specifying that the value of BK (1) is used to disable
this UDP AC upgrade.
Fixes: ebd5e764f9 ("Vendor attribute to configure QoS/AC upgrade for UDP frames")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce a new attribute QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE
to configure access category override for UDP frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduces a vendor command to get the currently enabled band(s)
through QCA_NL80211_VENDOR_SUBCMD_GETBAND.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Also introduce a new attribute QCA_WLAN_VENDOR_ATTR_SETBAND_MASK to
carry this new bitmask enum. This attribute shall consider the bitmask
combinations to define the respective band combinations and substitutes
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE. The old attribute use remains same
as before.
In addition, document the previously undocumented, but defined,
QCA_NL80211_VENDOR_SUBCMD_SETBAND.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use "client device" as the term for the device that operates under a
guidance of the device responsible for enforcing DFS rules.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define QCA vendor attribute in SET(GET)_WIFI_CONFIGURATION to
dynamically configure capabilities for dynamic bandwidth adjustment.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Define QCA vendor attribute in SET(GET)_WIFI_CONFIGURATION to
dynamically configure capabilities for channel width.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Add new QCA vendor attributes to configure RSNXE Used (FTE), ignore CSA,
and OCI frequency override with QCA vendor command
QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION for STA testbed role.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an attribute QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED
to get the response for the queried data.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
