Split the auth=none option into three: open, WEP, WEP with shared key to
allow the user specify WEP with shared key authentication. In addition,
fix static WEP key edits to be enabled only when using static WEP keys
(i.e., not for IEEE 802.1X).
wpa_supplicant should not send a dbus reply as response to a method call
if no reply was requested by the caller. Sending a reply even if not
requested is basically no problem but triggers dbus warnings like the
one below.
Feb 9 07:31:23 linux-gvjr dbus-daemon: Rejected send message, 2 matched
rules; type="error", sender=":1.129" (uid=0 pid=30228
comm="/usr/sbin/wpa_supplicant -c /etc/wpa_supplicant/wp")
interface="(unset)" member="(unset)" error
name="fi.epitest.hostap.WPASupplicant.InvalidInterface"
requested_reply=0 destination=":1.128" (uid=0 pid=30226
comm="/usr/sbin/NetworkManager "))
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Build EAP-WSC dynamically does not make much sense and with the
dependencies to WPS code from number of places resolving this is not
trivial. It is simpler to just remove this option.
If you don't choose OpenSSL as TLS implementation and choose to enable
CONFIG_EAP_TNC you have to link against libdl. The OpenSSL libraries
implicitly link against them, so this might be a reason why it wasn't
noticed yet. I assume the same applies to hostapd.
We can now handle up to 65535 byte result buffer which is the maximum
due to WEXT using 16-bit length field. Previously, this was limited to
32768 bytes in practice even through we tried with 65536 and 131072
buffers which we just truncated into 0 in the 16-bit variable.
This more or less doubles the number of BSSes we can received from scan
results.
If wpa_supplicant is started with -u but the DBus service is already
registered wpa_supplicant will bail out. However, it will segfault
in wpa_supplicant_deinit because global->drv_priv wasn't allocated
yet.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
This is based on a patch from Pavel Roskin <proski@gnu.org>, but with
the WIRELESS_DEV part removed instead of moved since it does not apply
anymore. Additional note on client MLME limitations was also added.
MadWifi is unlikely to be in ../head relative to hostapd or
wpa_supplicant, as it would be inside the hostap git repository.
MadWifi sources are more likely to be in a directory called "madwifi"
and residing outside the hostap repository. Using "madwifi" also
demonstrates that the top-level madwifi directory is needed.
If a Registrar tries to configure the AP, but fails to validate the
device password (AP PIN), lock the AP setup after four failures. This
protects the AP PIN against brute force guessing attacks.
Some WPS APs do not set Selected Registrar attribute to 1 properly when
using an external Registrar. Allow such an AP to be selected for PIN
registration after couple of scan runs that do not find APs marked with
Selected Registrar = 1. This allows wpa_supplicant to iterate through
all APs that advertise WPS support without delaying connection with
implementations that set Selected Registrar = 1 properly.
The default interval is now 5 seconds (used to be 1 second for
interactive mode and 2 seconds for wpa_cli -a). The interval can be
changed with -G<seconds> command line option.
The separate Association Comeback Time IE was removed from IEEE 802.11w
and the Timeout Interval IE (from IEEE 802.11r) is used instead. The
editing on this is still somewhat incomplete in IEEE 802.11w/D7.0, but
still, the use of Timeout Interval IE is the expected mechanism.
The wps_cred_process option can be used to configure wpa_supplicant to
send received Credential attributes for external processing over
ctrl_iface and dbus. This allows external programs to update their
configuration when WPS is used to provision new networks.
This makes it easier to pass the credential data to external programs
(e.g., Network Manager) for processing. The actual use of this data is
not yet included in hostapd/wpa_supplicant.
The current implementation does not support WPA/WPA2-Enterprise
credentials. Ignore any credential that is using unsupported
authentication type to avoid potential issues with partially configured
network blocks.
Must not set pairwise_cipher/group_cipher for non-WPA/WPA2 networks
since the configuration parser is going to reject such values. In
addition, should not limit group_cipher to just TKIP or TKIP|CCMP just
in case the AP is using WEP as the group cipher. Default group_cipher
value can be used for all cases.
RSN IBSS uses authentication per-STA and that is initialized separately,
so there is no need to enable the per-BSS like authentication that is
used with APs.
This makes wpa_gui remember whether it was only in the tray when the
session was terminated and starts only in the tray if session manager
restarts it automatically.
This commit adds a new build option, CONFIG_IBSS_RSN=y, that can be used
to enable RSN support for IBSS. This links in RSN Authenticator code
from hostapd and adds code for managing per-peer information for IBSS. A
new wpa_cli command or driver event can be used to request RSN
authentication with an IBSS peer. New RSN Authenticator and Supplicant
will be allocated for each peer.
The basic state machine setup code is included in this commit, but the
state machines are not properly started yet. In addition, some of the
callback functions are not yet complete.
Do not add the automatically generated RADIUS attributes NAS-IP-Address,
Calling-Station-Id, Framed-MTU, NAS-Port-Type, and Connect-Info if -N
option is used with the same attribute type. This allows these
attributes to be replaced without causing duplicate entries.
Fix compile warning by renaming gridLayout to wpsGridLayout in
wpagui.ui, it seems to be used internally.
/usr/bin/uic-qt4 eventhistory.ui -o .ui/ui_eventhistory.h
/usr/bin/uic-qt4 scanresults.ui -o .ui/ui_scanresults.h
/usr/bin/uic-qt4 wpagui.ui -o .ui/ui_wpagui.h
Warning: name gridLayout is already used
/usr/bin/uic-qt4 userdatarequest.ui -o .ui/ui_userdatarequest.h
/usr/bin/uic-qt4 networkconfig.ui -o .ui/ui_networkconfig.h
Also disable WPS tab if the running supplicant doesn't support that,
just as the WPS action menu is.
Signed-off-by: Kel Modderman <kel@otaku42.de>
It is better to have command description around the command definitions:
the chances for omitting usage, forgotting to change/delete them, etc.
are smaller than for the separate usage statement. [Bug 290]
Signed-off-by: Eygene Ryabinkin <rea-fbsd@codelabs.ru>
I had added flags to the every command description: just now the only
meaningful flag tells that this command has sensitive arguments and it
shouldn't be written to the disk. I rewrote the logics for the search
for the sensitive commands: special procedure is now loops over all
commands and tries to see if command has sensitive data. [Bug 289]
Signed-off-by: Eygene Ryabinkin <rea-fbsd@codelabs.ru>
First of all, the history had not been written to the disk, since almost
all commands were cleaned up due to the error in the history cleaning:
the return value of the last os_strncasecmp() call was not compared to
zero, but was rather used as is. So the condition was almost always
true and most commands were removed from the history.
The second problem was that the evaluation of the potentially sensitive
commands was started at the entry number 1, instead of very first entry.
