Add a parameter (non_coloc_6ghz=1) to the manual scan command to disable
6 GHz collocated scanning.
This option can be used to disable 6 GHz collocated scan logic. Note
that due to limitations on Probe Request frame transmissions on the 6
GHz band mandated in IEEE Std 802.11ax-2021 it is very likely that
non-PSC channels would be scanned passively and this can take a
significant amount of time.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This information was already available from the nl80211 control port RX
path, but it was not provided to upper layers within wpa_supplicant and
hostapd. It can be helpful, so parse the information from the driver
event.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds wifi_generation=7 line to the STATUS output if the driver
reports (Re)Association Request frame and (Re)Association Response frame
information elements in the association or connection event with EHT
capability IEs.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Sometimes there is a program error to send a large number of commands to
wpa_supplicant, and the source address can help quickly find the program
that sends commands.
Signed-off-by: xinpeng wang <wangxinpeng@uniontech.com>
To support the STA testbed role, the STA has to disable transmitting
EAPOL-Key group msg 2/2 of Group Key Handshake. Add test parameter to
disable sending EAPOL-Key group msg 2/2 of Group Key Handshake.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Support installing the updated allow/deny list to the driver if it
supports ACL offload. Previously, only the not-offloaded cases were
updated dynamically.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Extend AP mode ACL control interface commands to work from
wpa_supplicant in addition to the previously supported hostapd case.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Extend AP mode BTM control interface commands to work from
wpa_supplicant in additiona to the previously support hostapd case.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
dpp_configurator_params changes were taken into use in the
non-TCP/Controller case immediately on change, but that was not the case
for the Controller where this was updated only when explicitly starting
it. Change this to update dpp_configurator_params for the Controller as
well even if it is already running.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is mainly for testing purposes to allow a Configurator to the curve
between provisioning cases. This would not work for real deployement
cases unless every Enrollee were reconfigured.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The hwsim test cases are trying to clear this parameter between test
cases, but that was not really done correctly for many of the sigma_dut
test cases. Instead of fixing the text scripts to do this more
carefully, it seems to be simpler to just force the FLUSH command to
clear this.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This provides an alternative mechanism for upper layer components to
control configuration parameters to be used by the local Configurator.
Instead of the previously used design where the Configurator parameters
had to be provided before initiating the DPP Authentication exchange,
the new alternative approach allows the DPP Authentication exchange to
be started before any Configurator parameters have been determined and
wpa_supplicant will then request the parameters once the DPP
Configuration Request has been received from the Enrollee. This allows
the Config Request information to be used at upper layers to determine
how the Enrollee should be configured.
For example for an Initiator:
CTRL: DPP_QR_CODE <URI from Responder/Enrollee>
CTRL: DPP_AUTH_INIT peer=1 conf=query
<3>DPP-CONF-NEEDED peer=1 src=02:00:00:00:00:00 net_role=sta name="Test" opclass=81,82,83,84,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130 mud_url=N/A
(upper layer processing; potentially including user interaction)
CTRL: DPP_CONF_SET peer=1 conf=sta-sae ssid=736165 pass=70617373776f7264
<3>DPP-CONF-SENT
For example for a Responder:
CTRL: SET dpp_configurator_params conf=query
CTRL: DPP_LISTEN 2412 role=configurator
<3>DPP-CONF-NEEDED peer=2 src=02:00:00:00:01:00 net_role=sta name="Test" opclass=81,82,83,84,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130 mud_url=N/A
(upper layer processing; potentially including user interaction)
CTRL: DPP_CONF_SET peer=2 conf=sta-sae ssid=736165 pass=70617373776f7264
<3>DPP-CONF-SENT
For example for an Initiator that can act both as a Configurator and an
Enrollee in a case where the Initiator becomes the Enrollee:
CTRL: DPP_AUTH_INIT peer=1 role=either conf=query
<3>DPP-CONF-RECEIVED
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This allows the same functions to be used for both the control interface
and the D-Bus interface.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
CONFIG_DPP3=y can now be used to configure hostapd and wpa_supplicant
builds to include DPP version 3 functionality. This functionality is
still under design and the implementation is experimental and not
suitable to be enabled in production uses before the specification has
been finalized.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
While creating a cloned PMKSA entry for OKC both expiration and
reauth_time values are set to maximum values, but later only the
expiration time is copied from the old PMKSA entry to the new PMKSA
entry. Due to this there is a possibility of reauth_time becoming
greater than expiration time in some cloned entries. To avoid this copy
reauth_time also to the cloned entry.
Also, add check to reject control interface commands with reauth time
greater than expiration time.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Replaced the word "sanity" with the inclusive word "validity". The
comment in acs_survey_interference_factor() was referring a function
that does not exist, so remove it instead of trying rename the function.
Signed-off-by: Arowa Suliman <arowa@chromium.org>
Support adding/deleting vendor elements dynamically for AP mode while it
is started by wpa_supplicant instead of hostapd which already supported
this. This adds ap_assocresp_elements global parameter and UPDATE_BEACON
control interface command to take the changed values into effect.
Usage in wpa_cli:
Add vendor IE for (Re)Association Response frames
> set ap_assocresp_elements=xxxx
Add vendor IE for Beacon/Probe Response frames
> set ap_vendor_elements=xxxx
Delete vendor IE from (Re)Association Response frames
> set ap_assocresp_elements
Delete vendor IE from Beacon/Probe Response frames
> set ap_vendor_elements
To make vendor IE changes take effect
> update_beacon
Signed-off-by: Chaoli Zhou <zchaoli@codeaurora.org>
Add support to send DSCP Policy Query frame using a new control
interface command DSCP_QUERY. This includes support for a wildcard DSCP
query and a DSCP query with a single Domain Name attribute.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add support to prepare and send DSCP response action frame to the
connected AP in response to a new control interface command DSCP_RESP.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
The DSCP policy capability is disabled by default. The user frameworks
which have support for handling DSCP policy request messages need to
enable this capability explicitly to allow wpa_supplicant to advertise
the capability to the AP and allow the related frames to be processed.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Enhance the P2P_GROUP_ADD command to support DFS channel with 80 and 160
MHz bandwidth to be used for autonomous GO when using offloaded DFS.
For example, 'P2P_GROUP_ADD freq=5500 max_oper_chwidth=80 ht40 vht'
- Previous behavior: AP fallback to channel 100 using 20 MHz with
"No VHT higher bandwidth support for the selected channel 100"
- Enhanced behavior: AP starts on channel 100 using 80 MHz with
"VHT center channel 106 for 80 or 80+80 MHz bandwidth"
This functionality is on top of the driver's capability to offload DFS,
which is advertized through WPA_DRIVER_FLAGS_DFS_OFFLOAD.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enable support for P2P connection in 6 GHz with the channel width of 40
MHz, 80 MHz, and 160 MHz. The flag max_oper_chwidth is used to configure
the maximum channel width for P2P connection in 6 GHz with the commands
P2P_CONNECT, P2P_INVITE, and P2P_GROUP_ADD.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
"SET disable_mscs_support 1" can be used to disable indication of MSCS
support in the Extended Capabilities element for testing purposes. This
is also disabling addition of the MSCS element even if valid
configuration parameters had been configured.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
Add support to receive and process SCS Response frames from the AP and
indicate the status to upper layers.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
"SET disable_scs_support 1" can be used to disable indication of SCS
support in the Extended Capabilities element for testing purposes.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
Add support to parse SCS control interface command and form the SCS
Request frame to be sent to SCS enabled AP.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
External applications can store PMKSA entries persistently and
reconfigure them to wpa_supplicant after restart. This can result in
wpa_supplicant having a PMKSA for FILS authentication without having
matching ERP keys for it which would prevent the previously added
mechanism for dropping FILS PMKSA entries to recover from rejected
association attempts.
Fix this by clearing PMKSA entries configured by external applications
upon FILS connection failure even when ERP keys are not available.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Introduce a new allow_6ghz parameter with P2P_CONNECT, P2P_GROUP_ADD,
and P2P_INVITE commands for P2P connection on the 6 GHz channels when
Wi-Fi Display is enabled on both the devices. This commit is only adding
the interface change without changing any actual P2P functionality.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Previously, the 6 GHz channels were disabled for P2P operations.
Introduce a new include_6ghz parameter for the P2P_FIND command to
configure P2P discovery on the 6 GHz channels.
However, the p2p_6ghz_disable parameter in the configuration takes a
higher priority. If the p2p_6ghz_disable parameter is not set in the
configuration, include_6ghz parameter can be used to enable or disable
the discovery operation in the 6 GHz channels for the P2P_FIND command.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
This makes it convenient for an external test script to use
ext_eapol_frame_io=1 to delay and/or modify transmission of EAPOL-Key
msg 1/4 without having to use separate frame injection mechanisms.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Simplify the implementation by using shared functions for parsing the
capabilities instead of using various similar but not exactly identical
checks throughout the implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
Process the received comeback cookie and retry automatically if the AP
allows this. Otherwise, provide the cookie to upper layers to allow a
later attempt with the cookie.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The new wpa_supplicant control interface command "PASN_DEAUTH
bssid=<BSSID>" can now be used to flush the local PTKSA cache for the
specified BSS and to notify the AP to request it to drop its PTKSA as
well.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This adds new control interface commands TWT_SETUP and TWT_TEARDOWN. For
now, these are only for testing purposes to be able to trigger
transmission of the TWT Action frames without configuring any local
behavior for TWT in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The roam D-Bus and ROAM control itnerface commands flip the reassociate
bit before calling wpa_supplicant_connect(). wpa_supplicant connect
eventually aborts ongoing scans (if any), which causes scan results to
be reported. Since the reassociate bit is set, this will trigger a
connection attempt based on the aborted scan's scan results and cancel
the initial connetion request. This often causes wpa_supplicant to
reassociate to the same AP it is currently associated to instead of the
explicitly requested roaming target.
Add a roam_in_progress flag to indicate that we're currently attempting
to roam via an explicitly request to a specific BSS so that we don't
initiate another connection attempt based on the possibly received scan
results from a scan that was in progress at the time the roam command
was received.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Don't use 'protected' as the name of the variable in bss.h since this
might be used in control interfaces that use C++.
Fixes: 1c77f3d3f9 ("Indicate whether additional ANQP elements were protected")
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a more specific name for the control interface command used for
managing the list of BSSIDs that are temporarily ignored.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add PASN implementation to wpa_supplicant
1. Add functions to initialize and clear PASN data.
2. Add functions to construct PASN Authentication frames.
3. Add function to process PASN Authentication frame.
4. Add function to handle PASN frame TX status.
5. Implement the station side flow processing for PASN.
The implementation is missing support for wrapped data and PMKSA
establishment for base AKMs, and only supports PASN authentication or
base AKM with PMKSA caching.
The missing parts will be added in later patches.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
