Instead of returning "skip" from the test function, raise the new
HwsimSkip exception to indicate a test case was skipped.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for regulatory domain changes to "leak" into following
test cases in number of cases where the cfg80211 BSS table remained
after regulatory domain had been restored to world roaming. Try to make
this less likely to occur by explicitly clearing BSS table at the end of
test cases that use different regulatory domain. This makes P2P test
cases that verify channel selection based on world roaming rules more
robust.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids one more cleanup step between most test cases by stopping ER
only in case it was actually used during a test.
Signed-off-by: Jouni Malinen <j@w1.fi>
A single channel scan just before WPS_REG, WPS_PBC, and WPS_PIN commands
can be used to avoid having to run a full scan. This saves significant
amount of time in the WPS test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it more convenient and consistent to clear the cached scan
results from cfg80211 and wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The "Not fully connected" report did not clearly identify what went
wrong, so make this more verbose in hope of being able to determine what
happened should this test case fail again.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible to hit the 10 second timeout in some test cases under
heavy load (e.g., with large number of VMs running tests in parallel).
These timeouts are not really indicating any real error, so make them
less likely to show up in reports by increasing the connection timeout
to 30 seconds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed in preparation for WPS AES being mapped to enabling both
CCMP and GCMP if the driver supports both ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The scan for WPS-AUTH validation may miss a Probe Response frame if the
hostapd process gets blocked under load, e.g., when testing with
parallel-vm.sh.
Signed-off-by: Jouni Malinen <j@w1.fi>
Scan explicitly for the AP that may be started during the test case
execution. This is needed to work around issues where under heavy CPU
load, the single active scan round may miss the delayed Probe Response
from the second AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for the scan to miss a Probe Response frame especially
under heavy load, so try again to avoid reporting invalid failures.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for the final step of the test case to fail under load
(e.g., when using parallel-vm.sh with large number of VMs), so run
through additional scan iterations if the WPS-AUTH flag does not get
removed immediately.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This can fail if Probe Response frame is missed and Beacon frame was
used to fill in the BSS entry. This can happen, e.g., during heavy load
every now and then and is not really an error, so try to workaround by
runnign another scan.
Signed-off-by: Jouni Malinen <j@w1.fi>
run-tests.py now takes an optional --long parameter that can be used to
enable running of test cases that take a long time (multiple minutes).
By default, such test cases are skipped to avoid making the normal test
run take excessive amounts of time.
As an initial long test case, verify WPS PBC walk time expiration (two
minutes).
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait a bit between WPS_CONFIG command and the first scan. This can avoid
an extra five second wait due to having to scan again if the initial
scan operations happens to be quick enough to happen before the AP has
updated its configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Only run-tests.py is actually executed, so there is no need to specify
the interpreter in all the helper files and test script files.
Signed-off-by: Jouni Malinen <j@w1.fi>
WPS-ER-AP-REMOVE event from the ER is sent before HTTP UNSUBSCRIBE has
been completed. As such, it was possible for the following scan
validation step to be started before the AP has had a chance to react to
the ER status change. Makes this less likely to fail by waiting 200 ms
before starting the last scan.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was possible for the AP to report two enrollees in this test case
(i.e., both the expected wlan1 device and also the ER device on wlan0).
The previous test script would fail if the wlan0 device is reported
first. Fix this by allowed the expected target to be found in either the
first or the second WPS-ER-ENROLLEE-ADD event.
Signed-hostap: Jouni Malinen <j@w1.fi>
Now that wpa_supplicant requests the driver (cfg80211) to clear its scan
cache automatically after each BSS_FLUSH/FLUSH command, the previously
used ignore_old_scan_res workaround should not be needed for the hwsim
test cases anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
The run-tests.py -l argument does not take an argument value anymore.
Instead, debug output is directed to a separate file <test>.log for each
test case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is another one of the test cases that can time out frequently
under valgrind during WPS exchange. Increase the timeout to make
false error reports less likely to occur.
Signed-hostap: Jouni Malinen <j@w1.fi>
Number of crypto operations seem to take very long time in the valgrind
tests (about five seconds for public key generation for M1 and M2 on a
virtual server) and this is enough to push the test runs to hit the
timeout frequently even when there is no real error. Make this less
frequent by increasing WPS test case timeout from 15 to 30 seconds to
avoid issues based on the test scripts.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like there may not be enough time to complete this test case in
15 seconds under valgrind on a virtual host every time, so increase the
timeout to 30 seconds to get more consistent test results.
Signed-hostap: Jouni Malinen <j@w1.fi>
The WPS tests are more prone to fail if scan results from the previous
test cases are allowed to remain in the wpa_supplicant BSS table during
the consecutive test since the test setup uses the same BSSID for the
test APs that change their configuration. Avoid these mostly bogus
issues by enforcing wpa_supplicant to drop and ignore old scan results
during the WPS test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
