This moves the implementation closer to the current IEEE 802.11 standard
since B15 of Frame Control field was renamed to +HTC to match it newer
uses.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor interface for userspace to get information of usable
channels for different interface types from the driver/firmware.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Determine bandwidth from op_class parameter when set in config. When not
configured, use he_oper_chwidth for determining 80 MHz or 160 MHz. When
both are not set, fall back to 20 MHz by default. This helps in removing
the dependency on op_class parameter in 6 GHz ACS.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Add support for the 6 GHz frequencies using 40, 80, and 160 MHz
bandwidths in the AP mode ACS.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Convert channel based selection to frequency based selection for AP mode
ACS to accommodate for the 6 GHz band needs.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Previously, the secondary channel was set only in presence of HT
capabilities based on HT40+ or HT40-. As HT capabilities and
secondary_channel are not present for the 6 GHz bamd, this causes
incorrect operating class indication in the Supported Operating Classes
element.
Fix this by assigning the secondary channel for bandwidths greater than
20 MHz in the 6 GHz band.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
In the 6 GHz Operation Information field, the Channel Center Frequency
Segment 0 field indicates the channel center frequency index for
the 20 MHz, 40 MHz, 80 MHz, or 80+80 MHz channel on which the
BSS operates in the 6 GHz band. If the BSS channel width is 160 MHz
then the Channel Center Frequency Segment 0 field indicates the
channel center frequency index of the primary 80 MHz.
The Channel Center Frequency Segment 1 field indicates the channel
center frequency index of the 160 MHz channel on which the BSS operates
in the 6 GHz band or the channel center frequency of the secondary 80
MHz for the 80+80 MHz channel.
Since Channel Center Frequency Segment 1 was 0 for 160 MHz, 6 GHz STA
associated using 80 MHz. Update seg0 and seg1 fields per standard (IEEE
P802.11ax/D8.0: 9.4.2.249 HE Operation element).
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
When WMM is disabled, HT/VHT/HE capabilities should not be used for any
STA. If any STA advertises these capabilities, hostapd AP disables HT
capabilities in STA flags during STA assoc, but VHT/HE was not handled
similarly. This could allow a STA to associate in VHT/HE mode even in
WMM disable case.
To avoid this, disable VHT/HE capabilities similarly to HT during STA
association, if WMM is not enabled by the STA.
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Even though these enum definitions are currently identical, it is better
to explicitly map these bits to the kernel interface instead of using
the internal definition for this. This makes it much clearer that new
enum tdls_peer_capability value needs to be assigned in nl80211 before
they can be added into wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Indicate TDLS peer's capability to driver after processing TDLS setup
response frame. This information can be used by the driver to decide
whether to include HE operation IE in TLDS setup confirmation frame.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
The hostapd process crashed when the UPDATE_BEACON control interface
command was issue after the interface was disabled. Check for this case
and return an error if the interface is disabled.
Signed-off-by: Kani M <kanisumi@codeaurora.org>
Get the DPP Relay Controller context from the list of configured
Controllers based on the correct hostapd callback context. This is
needed to pick the correct hostapd interface for sending out the
response over air, e.g., when the same hostapd process controls a 2.4
GHz only and a 5 GHz only interface.
Signed-off-by: Disha Das <dishad@codeaurora.org>
The firmware rejects the TWT setup request when scan is in
progress. Extend enum qca_wlan_vendor_twt_status to represent new
reason code for it.
Signed-off-by: Mohammad Asaad Akram <asadkrm@codeaurora.org>
Define a new reason code in enum qca_wlan_vendor_hang_reason,
QCA_WLAN_TASKLET_CREDIT_LATENCY_DETECT, for tasklet/credit latency
detection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce a QCA vendor command to configure the concurrent connection
policies when multiple STA interfaces are (getting) active.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add timeout to close incomplete DPP relay connections. This is needed to
avoid getting stuck with old entries that prevent new connections from
getting started.
Signed-off-by: Disha Das <dishad@codeaurora.org>
When CONFIG_ECC is not defined, openssl/ec.h is not included and EC_KEY
not known. Fix be not defining EVP_PKEY_get0_EC_KEY() when CONFIG_ECC is
not defined.
Signed-off-by: Wolfgang Steinwender <wsteinwender@pcs.com>
Simplify the implementation by using shared functions for parsing the
capabilities instead of using various similar but not exactly identical
checks throughout the implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2020 mandates H2E to be used whenever an SAE password
identifier is used. While this was already covered in the
implementation, the sae_prepare_commit() function still included an
argument for specifying the password identifier since that was used in
an old test vector. Now that that test vector has been updated, there is
no more need for this argument anymore. Simplify the older non-H2E case
to not pass through a pointer to the (not really used) password
identifier.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do so for both wpa_supplicant and hostapd. While this was not explicitly
required in IEEE P802.11az/D3.0, likely direction for the draft is to
start requiring use of H2E for all cases where SAE is used with PASN.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a PTK derivation is done as part of PASN authentication flow, a KDK
derivation should be done if and only if the higher layer protocol is
supported by both parties.
Fix the code accordingly, so KDK would be derived if and only if both
sides support Secure LTF.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Define the new TWT attributes for configuring the broadcast TWT
parameters in enum qca_wlan_vendor_attr_twt_setup.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The firmware rejects the TWT setup request when roaming and channel
switch is in progress. Extend enum qca_wlan_vendor_twt_status to
represent new reason codes for these cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This changes the Send-Confirm value for the first SAE Confirm message to
be 1 instead of 0 for all cases to match the design shown in IEEE Std
802.11-2020, Figure 12-4 (SAE finite state machine).
Sc is defined to be "the number of SAE Confirm messages that have been
sent" which is a bit vague on whether the current frame is included in
the count or not. However, the state machine is showing inc(Sc)
operation in all cases before the "2" event to build the Confirm.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the maximum size of MAC ACL entries is large enough, the
configuration message may exceed the default buffer size of a netlink
message which is allocated with nlmsg_alloc(), and result in a failure
when putting the attributes into the message.
To fix this, calculate the required buffer size of the netlink message
according to MAC ACL size and allocate a sufficiently large buffer with
nlmsg_alloc_size().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
NL80211_ATTR_MAC_ACL_MAX is a u32 attribute to advertise the maximum
number of MAC addresses that a device can support for MAC ACL. This was
incorrectly used as a u8 attribute which would not work with any values
larger than 255 or on big endian CPUs. Fix this by moving from
nla_get_u8() to nla_get_u32().
Fixes: 3c4ca36330 ("hostapd: Support MAC address based access control list")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If WMM is not set explicitly in the configuration, it can be set based
on HT/HE config. As HE can be used without HT/VHT (which was introduced
as a special behavior for the 6 GHz band), add a similar automatic
enabling of WMM for HE without HT.
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Previous debug print used IGTK instead of BIGTK, so fix that to use the
correct key. Actual generation of the BIGTK subelement itself was using
the correct key, though, so this is only needed to fix the debug print.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameters ext_capa_mask and ext_capa can
now be used to mask out or add extended capability bits. While this is
not without CONFIG_TESTING_OPTIONS, the main use case for this is for
testing purposes.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to determine the exact length of the element before
filling in the octets since this function is already capable of
truncated the fields based on what the actual values are.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reuse the SAE anti-clogging token implementation to support similar
design with the PASN comeback cookie.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The GAS client processing of the response callback for DPP did not
properly check for GAS query success. This could result in trying to
check the Advertisement Protocol information in failure cases where that
information is not available and that would have resulted in
dereferencing a NULL pointer. Fix this by checking the GAS query result
before processing with processing of the response.
This is similar to the earlier wpa_supplicant fix in commit 931f7ff656
("DPP: Fix GAS client error case handling").
Signed-off-by: Jouni Malinen <j@w1.fi>
eap_sim_anonymous_username() gets called with an argument that is not a
null terminated C string and as such, os_strrchr() and os_strlen()
cannot be used with it. The previous implementation resulted in use of
uninitialized values and a potential read beyond the end of the buffer.
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=32277
Fixes: 73d9891bd7 ("EAP-SIM/AKA peer: Support decorated anonymous identity prefix")
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible to receive the Configuration Request frame before having
seen TX status for the Authentication Confirm. In that sequence, the
DPP-AUTH-SUCCESS event would not be indicated before processing the
configuration step and that could confuse upper layers that follow the
details of the DPP exchange. As a workaround, indicate DPP-AUTH-SUCCESS
when receiving the Configuration Request since the Enrollee/Responser
has clearly receive the Authentication Confirm even if the TX status for
it has not been received.
This was already done in wpa_supplicant in commit 422e73d623 ("DPP:
Indicate authentication success on ConfReqRX if needed") and matching
changes are now added to hostapd.
Signed-off-by: Jouni Malinen <j@w1.fi>
Need to get EAP state machine into a state where it is willing to
proceed with a new EAP-Request/Identity if PMKSA cache addition fails
after a successful EAP authentication before the initial 4-way handshake
can be completed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The waiting_conn_status_result flag was not set which made hostapd
discard the Connection Status Result. Fix this to match the
wpa_supplicant implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a new testing parameter to allow airtime policy implementation to be
tested for more coverage even without kernel driver support.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is better to be able to determine whether the airtime weight
configuration for a STA actually was accepted by the driver or not.
Signed-off-by: Jouni Malinen <j@w1.fi>
The firmware sends new reason codes to indicate TWT teardown due to
single channel and multi channel concurrency. Update the enum
qca_wlan_vendor_twt_status to represent new reason code.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
To allow for a PASN station to deauthenticate from an AP to clear any
PTKSA cache entry for it, extend the nl80211 interface to allow sending
a Deauthentication frame with off channel enabled.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a Deauthentication frame is received, clear the corresponding PTKSA
cache entry for the given station, to invalidate previous PTK
information.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The anti-clogging code was under CONFIG_SAE. Change this so it can be
used both with CONFIG_SAE and CONFIG_PASN.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
PASN authentication mandates support for comeback flow, which
among others can be used for anti-clogging purposes.
As the SAE support for anti clogging can also be used for PASN,
start modifying the source code so the anti clogging support
can be used for both SAE and PASN.
As a start, rename some variables/functions etc. so that they would not
be SAE specific. The configuration variable is also renamed, but the old
version remains available for backwards compatibility.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
For testing purposes, add support for corrupting the MIC in PASN
Authentication frames for both wpa_supplicant and hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a public key is included in the PASN Parameters element, it should
be encoded using the RFC 5480 conventions, and thus the first octet of
the Ephemeral Public Key field should indicate whether the public key is
compressed and the actual key part starts from the second octet.
Fix the implementation to properly adhere to the convention
requirements for both wpa_supplicant and hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
As defined in IEEE P802.11az/D3.0, 12.12.3.2 for the second PASN frame.
This was previously covered only for the case when the explicit PMKSA
was provided to the helper function. Extend that to cover the PMKID from
SAE/FILS authentication cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When ERP initialization was moved from the METHOD state to the SUCCESS
state, the conditions for checking against EAP state being cleared was
missed. The METHOD state verified that sm->m is not NULL while the
SUCCESS state did not have such a check. This opened a window for a race
condition where processing of deauthentication event and EAPOL RX events
could end up delivering an EAP-Success to the EAP peer state machine
after the state had been cleared. This issue has now been worked around
in another manner, but the root cause for this regression should be
fixed as well.
Check that the EAP state machine is properly configured before trying to
initialize ERP in the SUCCESS state.
Fixes: 2a71673e27 ("ERP: Derive ERP key only after successful EAP authentication")
Signed-off-by: Jouni Malinen <j@w1.fi>
The highest supported TLS version for pre_master_secret needs to be
limited based on the local configuration for the case where the highest
version number is being explicitly disabled. Without this, the server
would likely detect a downgrade attack.
Signed-off-by: Jouni Malinen <j@w1.fi>
The supported hash algorithms do not use AlgorithmIdentifier parameters.
However, there are implementations that include NULL parameters in
addition to ones that omit the parameters. Previous implementation did
not check the parameters value at all which supported both these cases,
but did not reject any other unexpected information.
Use strict validation of digest algorithm parameters and reject any
unexpected value when validating a signature. This is needed to prevent
potential forging attacks.
Signed-off-by: Jouni Malinen <j@w1.fi>
Digest is within the DigestInfo SEQUENCE and as such, parsing for it
should use the end of that data instead of the end of the decrypted
signature as the end point. Fix this in the PKCS #1 and X.509
implementations to avoid accepting invalid digest data that is
constructed to get the hash value from after the actual DigestInfo
container.
Signed-off-by: Jouni Malinen <j@w1.fi>
The definite long form for the length is allowed only for cases where
the definite short form cannot be used, i.e., if the length is 128 or
greater. This was not previously enforced and as such, multiple
different encoding options for the same length could have been accepted.
Perform more strict checks to reject invalid cases for the definite long
form for the length. This is needed for a compliant implementation and
this is especially important for the case of verifying DER encoded
signatures to prevent potential forging attacks.
Signed-off-by: Jouni Malinen <j@w1.fi>
The extended tag case is allowed only for tag values that are 31 or
larger (i.e., the ones that would not fit in the single octet identifier
case with five bits). Extended tag format was previously accepted even
for the values 0..31 and this would enable multiple different encodings
for the same tag value. That is not allowed for DER.
Perform more strict checks to reject invalid extended tag values. This
is needed for a compliant implementation and this is especially
important for the case of verifying DER encoded signatures to prevent
potential forging attacks.
Signed-off-by: Jouni Malinen <j@w1.fi>
The identifier octet in DER encoding includes three components. Only two
of these (Class and Tag) were checked in most cases when looking for a
specific data type. Also check the Primitive/Constructed bit to avoid
accepting invalid encoding.
This is needed for correct behavior in DER parsing and especially
important for the case of verifying DER encoded signatures to prevent
potential forging attacks.
Signed-off-by: Jouni Malinen <j@w1.fi>
Send a flag to the kernel when user has specified disable_he=1 in the
network configuration block. This extends the functionality added in
commit 7c8f540ee0 ("wpa_supplicant: Add HE override support") to cover
the cases that need kernel functionality.
Signed-off-by: Ben Greear <greearb@candelatech.com>
If listen work never started, pending_listen_freq might be left
uncleared, preventing the subsequent listen to start. This could happen
in p2p_timeout_wait_peer_idle() after the commit 13256b8cf ("P2P: Stop
old listen radio work before go to WAIT_PEER_IDLE state") added a
stop_listen() call there.
Fixes: 13256b8cf3 ("P2P: Stop old listen radio work before go to WAIT_PEER_IDLE state")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The 6 GHz band operating class 136 is defined to use 20 MHz bandwidth.
Return the value accordingly from center_idx_to_bw_6ghz() to cover this
special case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the following additional TWT attribute for
qca_wlan_vendor_attr_twt_setup:
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL2_MANTISSA to configure the
mantissa in microseconds.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds new control interface commands TWT_SETUP and TWT_TEARDOWN. For
now, these are only for testing purposes to be able to trigger
transmission of the TWT Action frames without configuring any local
behavior for TWT in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This function can get called with hapd->wpa_auth == NULL from the
control interface handler, so explicitly check for that.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to be able to move from 80 MHz or lower bandwidth to 160
or 80+80 MHz bandwidth (and back) properly without leaving the Beacon
frame VHT elements showing incorrect information.
Signed-off-by: Jouni Malinen <j@w1.fi>
In addition, make the compiler warn if a new enum value is added without
defining the matching mapping to a string.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is more convenient to see the exact error in the debug log instead of
getting noted that something was invalid.
Signed-off-by: Jouni Malinen <j@w1.fi>
The nl_connect is initialized with the process_bss_event() handler.
However, it is used several times with the default valid handler. As a
result, if a message that is only valid for process_bss_event() is
received while the default handler is used, it will be dropped.
This has been observed in a case where during the 4-way handshake, a
Beacon frame is received on the AP side, which triggers a beacon update,
just before receiving the next EAPOL. When send_and_recv_msgs_owner() is
called for sending the NL80211_CMD_SET_BEACON command, the
NL80211_CMD_CONTROL_PORT_FRAME event is already pending. As a result, it
is received with the default handler, which drops it. Since the EAPOL
frame is dropped, the connection attempt fails.
Fix it by using the process_bss_event() handler when the nl_connect
handler is used.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
While it does not look like the stale pointer could have been
dereferenced in practice, it is better not to leave the stale pointer to
freed memory in place to avoid accidental uses.
Signed-off-by: Jouni Malinen <j@w1.fi>
hapd->tmp_eap_user needs to be cleared on interface deinit to avoid
leaving stale pointers to freed memory.
Fixes: ee431d77a5 ("Add preliminary support for using SQLite for eap_user database")
Signed-off-by: Jouni Malinen <j@w1.fi>
When an interface is disabled, e.g. due to radar detected,
hapd->time_adv is freed by hostapd_free_hapd_data(), but later
used by ieee802_11_build_ap_params() calling hostapd_eid_time_adv().
Thus hapd->time_adv needs to be cleared as well.
Fixes: 39b97072b2 ("Add support for Time Advertisement")
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Add a QCA vendor attribute to configure the driver to allow the 6 GHz
connection with all security types. This attribute is used for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to ignore SAE H2E requirement mismatch for 6
GHz connection. This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
sm->bssid is still the BSSID of the previous AP at this point in the FT
protocol, so need to show the target AP's BSSID instead in the failure
message.
Fixes: 8c1f61e820 ("OCV: Report OCI validation failures with OCV-FAILURE messages (STA)")
Signed-off-by: Jouni Malinen <j@w1.fi>
This is an attempt of making the code easier to understand for static
analyzers. The helper functions were already verifying that these IEs
are fully within the memory buffer, but that may not have been clear
enough for automated analysis.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit f1df4fbfc7 ("mesh: Use setup completion callback to complete
mesh join") added a check for iface->conf being NULL into a debug print.
However, it is not clear how that could be NULL here. In any case,
setup_interface() could end up dereferencing iface->conf in the call to
hostapd_validate_bssid_configuration(), so better be consistent with the
checks and not get warnings from static analyzers regardless of whether
this can happen in practice.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no point in trying to build in rest of this function if in the
middle of it the CONFIG_NO_RADIUS case would unconditionally fail.
Simply make all of this be conditional on that build parameter not being
set to make things easier for static analyzers.
Signed-off-by: Jouni Malinen <j@w1.fi>
The value from the initial RSN_CIPHER_SUITE_NO_GROUP_ADDRESSED check
ended up getting overridden with the following if. This was supposed to
be a single if statement to avoid that.
Fixes: 9c02a0f5a6 ("FILS: Add generation of FILS Discovery frame template")
Signed-off-by: Jouni Malinen <j@w1.fi>
Build eap_*.so into the wpa_supplicant similarly with the wpa_supplicant
binary and include the shared helper functions from additional files
into the builds. This got broken at some point with the build system
changes.
Signed-off-by: Jouni Malinen <j@w1.fi>
These frames are used for verifying that a specific SA and protected
link is in functional state between two devices. The IEEE 802.11
standard defines only a case that uses individual MAC address as the
destination. While there is no explicit rule on the receiver to ignore
other cases, it seems safer to make sure group-addressed frames do not
end up resulting in undesired behavior. As such, drop such frames
instead of interpreting them as valid SA Query Request/Response.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use a helper function as the do_acs() callback to allow builds to pull
in all the vendor specific operations into a single binary.
Signed-off-by: Jouni Malinen <j@w1.fi>
BRCM vendor command used to trigger ACS scan. After ACS finished,
DHD driver will send results by event BRCM_VENDOR_EVENT_ACS.
Signed-off-by: Xinrui Sun <xinrui.sun@broadcom.com>
Allow the RADIUS client socket to be bound to a specific netdev. This
helps hostapd work better in VRF and other fancy network environments.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Andreas Tobler <andreas.tobler at onway.ch>
Add DRIVER command support on hostapd and hostapd_cli on Android
similarly to the way this previously enabled in wpa_supplicant and
wpa_cli.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Determine if the TDLS peer is HE capable based on HE Capability element
received in the TDLS Setup Response frame. Indicate the peer's HE
capabilities to the driver through sta_add().
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
p2p_add_device() may remove the oldest entry if there is no room in the
peer table for a new peer. This would result in any pointer to that
removed entry becoming stale. A corner case with an invalid PD Request
frame could result in such a case ending up using (read+write) freed
memory. This could only by triggered when the peer table has reached its
maximum size and the PD Request frame is received from the P2P Device
Address of the oldest remaining entry and the frame has incorrect P2P
Device Address in the payload.
Fix this by fetching the dev pointer again after having called
p2p_add_device() so that the stale pointer cannot be used.
Fixes: 17bef1e97a ("P2P: Add peer entry based on Provision Discovery Request")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to enable/disable the Punctured Preamble Rx
support in HE PHY capabilities.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver to disable data and
management response frame transmission to test the BSS max idle period
feature.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver/firmware to use only
RU 242 tone for data frame transmission.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver with a specific BSS
max idle period value to advertise in (Re)Association Request frames.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reordering of code in handle_auth_cb() when adding support for full
station state messaged up frame length checks. The length was originally
tested before looking at the payload of the frame and that is obviously
the correct location for that check. The location after those full state
state changes was after having read six octets of the payload which did
not help at all since there was no addition accesses to the payload
after that check.
Move the payload length check to appropriate place to get this extra
level of protection behaving in the expected manner. Since this is a TX
status callback handler, the frame payload is from a locally generated
Authentication frame and as such, it will be long enough to include
these fields in production use cases. Anyway, better keep this check in
working condition.
Fixes: bb598c3bdd ("AP: Add support for full station state")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The TX event for the next frame in the sequence might be received before
the TX status for the final GAS response frame is processed. This used
to result in the Config Result getting discarded and the negotiation not
completing successfully on the Configurator side.
Accept the Config Result message as an indication of the final GAS
response frame having went through fine even if the TX status has not
yet been processed to avoid this issue from a potential race condition
on kernel events.
Signed-off-by: Jouni Malinen <j@w1.fi>
Replace the Radiotap parser platform.h file with use of helper functions
from utils/common.h to avoid compiler issues with the updated design and
getting pointers to members of packet structs.
Silence the warning about _next_bitmap assignment. This pointer is
dereferenced only with operations that are safe for unaligned access, so
the compiler warning is not helpful here.
__packed might not be defined in this context, so use STRUCT_PACKED from
utils/common.h.
Fixes: e6ac269433 ("radiotap: Update radiotap parser")
Signed-off-by: Jouni Malinen <j@w1.fi>
Use the explicit Commitment Message per draft-ietf-emu-eap-tls13-13
Section 2.5 and extend this functionality to PEAP and EAP-TTLS when
using TLS 1.3.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Recognize the explicitly defined Commitment Message per
draft-ietf-emu-eap-tls13-13 at the conclusion of the EAP-TTLS with TLS
1.3.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Recognize the explicitly defined Commitment Message per
draft-ietf-emu-eap-tls13-13 at the conclusion of the EAP-TLS with TLS
1.3.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
This newer Session-Id/Method-Id derivation is used with PEAP and
EAP-TTLS when using TLS 1.3 per draft-ietf-emu-tls-eap-types-00, so do
not limit this to only EAP-TLS.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Use the TLS-Exporter with the label and context as defined in
draft-ietf-emu-tls-eap-types-00 when deriving keys for EAP-TTLS with TLS
1.3.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Use the TLS-Exporter with the label and context as defined in
draft-ietf-emu-tls-eap-types-00 when deriving keys for PEAP with TLS
1.3.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
EAP peer does not expect data present when beginning the Phase 2 in
EAP-{TTLS,PEAP} but in TLS 1.3 session tickets are sent after the
handshake completes.
There are several strategies that can be used to handle this, but this
patch picks up from the discussion[1] and implements the proposed use of
SSL_MODE_AUTO_RETRY. SSL_MODE_AUTO_RETRY has already been enabled by
default in OpenSSL 1.1.1, but it needs to be enabled for older versions.
The main OpenSSL wrapper change in tls_connection_decrypt() takes care
of the new possible case with SSL_MODE_AUTO_RETRY for
SSL_ERROR_WANT_READ to indicate that a non-application_data was
processed. That is not really an error case with TLS 1.3, so allow it to
complete and return an empty decrypted application data buffer.
EAP-PEAP/TTLS processing can then use this to move ahead with starting
Phase 2.
[1] https://www.spinics.net/lists/hostap/msg05376.html
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Previously nl80211_nlmsg_clear() would be called under a special
condition when valid_handler is NULL and valid_data is -1. Such API is
not very convenient as it forces the handler to be NULL. Change the
send_and_recv() function to always clear the nl_msg, which will simplify
all this logic.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The capability bit index should not be shifted here as the shifting is
handled later below when building the RSNXE octets.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The RADIUS client currently determines if a radius message is longer
than the supported maximum length by checking whether the size of the
received buffer and the length of the buffer (as returned by recv()) is
equal. This method fails to detect if the buffer has actually been
truncated. This change modifies the RADIUS client to instead use the
recvmsg() call and then check the message header flags to determine
whether or not the received message has been truncated and drop the
message if that is the case.
Signed-off-by: Anusha Datar <anusha@meter.com>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Reviewed-by: Julian Squires <julian@cipht.net>
The current RADIUS server message maximum length limits the length of
each RADIUS message to 3000 bytes. As specified in RFC 2865 section 3
("Packet Format"), the RADIUS standard's maximum message size is 4096
bytes, so this change increases the RADIUS server's maximum message
size from 3000 to 4096 to match the standard.
Signed-off-by: Anusha Datar <anusha@meter.com>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Reviewed-by: Julian Squires <julian@cipht.net>
The RADIUS client currently uses a hardcoded value of 3000 for the
maximum length of a RADIUS message, and the RADIUS server currently
defines a constant value for the maximum length of the RADIUS message
within its source. The client and the server should use the same
maximum length value, so this change creates a shared parameter
RADIUS_MAX_MSG_LEN within the header file radius.h and modifies
both the client and the server to use that parameter instead of
a locally set value.
Signed-off-by: Anusha Datar <anusha@meter.com>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Reviewed-by: Julian Squires <julian@cipht.net>
Add additional attributes for the QCA vendor command
QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO to get finer details on roaming
behavior, TSF out of sync count, and the latest TX rate, Rate Index used
for the transmission.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When the driver SME is used, offloaded handshakes which need Operating
Channel Validation (OCV) such as SA Query procedure, etc. would fail if
hostapd enables OCV based on configuration but the driver doesn't
support OCV. To avoid this when driver SME is used, enable OCV from
hostapd only when the driver indicates support for OCV.
This commit also adds a capability flag to indicate whether driver SME
is used in AP mode.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
When the driver SME is used, offloaded RSN handshakes like SA Query, GTK
rekeying, FT authentication, etc. would fail if wpa_supplicant enables
OCV in initial connection based on configuration but the driver doesn't
support OCV. To avoid such failures check the driver's capability for
enabling OCV when the driver SME used.
This commit also adds a capability flag for indicating OCV support
by the driver.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Enabling beacon protection will cause STA connection/AP setup failures
if the driver doesn't support beacon protection. To avoid this, check
the driver capability before enabling beacon protection.
This commit also adds a capability flag to indicate beacon protection
support in client mode only.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
It was not easily possible to separate configuration of an interface and
credentials when using the configuration file instead of the control
interface or D-Bus interface for setting up the network profiles. This
makes it hard to distribute configuration across a set of nodes which
use wpa_supplicant without also having to store credentials in the same
file. While this can be solved via scripting, having a native way to
achieve this would be preferable.
Turns out there already is a framework to have external password
storages. It only had a single "test" backend though, which is kind of
an in-memory store which gets initialized with all passwords up front
and is mainly for testing purposes. This isn't really suitable for the
above use case: the backend cannot be initialized as part of the central
configuration given that it needs the credentials, and we want to avoid
scripting.
This commit thus extends the infrastructure to implement a new backend,
which instead uses a simple configuration file containing key-value
pairs. The file follows the format which wpa_supplicant.conf(5) uses:
empty lines and comments are ignored, while passwords can be specified
with simple `password-name=password-value` assignments.
With this new backend, splitting up credentials and configuration
becomes trivial:
# /etc/wpa_supplicant/wpa_supplicant.conf
ext_password_backend=file:/etc/wpa_supplicant/psk.conf
network={
ssid="foobar"
psk=ext:foobar
}
# /etc/wpa_supplicant/psk.conf
foobar=ecdabff9c80632ec6fcffc4a8875e95d45cf93376d3b99da6881298853dc686b
Alternative approaches would be to support including other configuration
files in the main configuration, such that common configuration and
network declarations including credentials are split up into separate
files. But the implementation would probably have been more complex
compared to reusing the already-existing framework for external password
backends.
Signed-off-by: Patrick Steinhardt <ps@pks.im>
The function wpa_config_get_line() is used by the wpa_supplicant config
file parser to retrieve the next non-comment non-blank line. We'll need
the same kind of functionality to implement the file-based external
password backend, so as a preparatory step this commit extracts the
function into its own standalone file in the utils package.
No functional changes are expected from this commit.
Signed-off-by: Patrick Steinhardt <ps@pks.im>
At least the ACS case of an attempt to pick a 40 MHz channel on the 2.4
GHz band could fail if HE was enabled and the driver did not include
support for 40 MHz channel bandwidth on the 2.4 GHz band in HE
capabilities. This resulted in "40 MHz channel width is not supported in
2.4 GHz" message when trying to configure the channel and failure to
start the AP.
Avoid this by automatically falling back to using 20 MHz bandwidth as
part of channel parameter determination at the end of the ACS procedure.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When auto channel selection (ACS) is used for HE 40 MHz in the 2.4 GHz
band, AP sets center frequency after finding a 40 MHz channel and then
runs a scan for overlapping BSSes in neighboring channels. Upon OBSS
detection, AP should downgrade to 20 MHz bandwidth.
This was broken because allowed_ht40_channel_pair() returns true in this
case and the steps to reset center frequency are not executed causing
failure to bring interface up.
Fix the condition to allow rollback to 20 MHz.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Unsolicited broadcast Probe Response transmission is used for in-band
discovery in the 6 GHz band (IEEE P802.11ax/D8.0 26.17.2.3.2, AP
behavior for fast passive scanning). Add support for configuring the
parameters for such frames.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Add hostapd configuration options for unsolicited broadcast
Probe Response transmission for in-band discovery in 6 GHz.
Maximum allowed packet interval is 20 TUs (IEEE P802.11ax/D8.0
26.17.2.3.2, AP behavior for fast passive scanning).
Setting value to 0 disables the transmission.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
This makes the error message easier to understand if the AP mode setup
failure is caused by invalid secondary channel configuration while the
primary channel is valid.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add hostapd configuration parameters for FILS Discovery frame
transmission interval and prepare a template for FILS Discovery frame
for the driver interface. The actual driver interface changes are not
included in this commit.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
This information is needed in more than one place, so add a helper
function to avoid need to duplicate this code.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add definitions from IEEE Std 802.11ai-2016, 9.6.8.36 FILS discovery
frame format and extensions for the 6 GHz band from IEEE P802.11ax/D8.0.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
A similar change was previously done for Probe Response frames, but the
Beacon frame case was missed. Fix this to remove the VHT elements also
from Beacon frames on the 6 GHz since the relevant information is
included only in the HE elements on that band.
Fixes: 49e95ee1ee ("AP: Publish only HE capabilities and operation IEs on 6 GHz band")
Signed-off-by: Jouni Malinen <j@w1.fi>
According to IEEE P802.11ax/D8.0, add Transmit Power Envelope element
into Beacon and Probe Response frames when operating HE AP on the 6 GHz
band.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
hostapd_get_oper_chwidth(iconf) instead of direct access to
iface->conf->vht_oper_chwidth is needed here to be able to use this with
HE in cases where VHT is not enabled.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
According to latest IEEE 802.11 standard, Transmit Power Envelope
element is also relevant to IEEE 802.11ax and is no longer called VHT
Transmit Power Envelope. Remove the VHT naming from the element and move
hostapd_eid_txpower_envelope() from ieee802_11_vht.c to ieee802_11.c in
preparation of using it with HE.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
nl80211_set_4addr_mode() could fail when trying to enable 4addr mode on
an interface that is in a bridge and has 4addr mode already enabled.
This operation would not have been necessary in the first place and this
failure results in disconnecting, e.g., when roaming from one backhaul
BSS to another BSS with Multi AP.
Avoid this issue by ignoring the nl80211 command failure in the case
where 4addr mode is being enabled while it has already been enabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
The HE 6 GHz capability was not being sent to the kernel causing 6 GHz
support being unidentifiable in the kernel driver for added stations.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
The Authentication Request frames triggered by the reception of a
Presence Announcement frame were sent to the broadcast address. This is
not correct behavior since the source MAC address of the Presence
Announcement frame was supposed to override the Responder MAC address.
Fix this by using that source MAC address to avoid unnecessary use of
broadcast frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new status code values for SAE H2E and PK resulted in the
sta->added_unassoc cases incorrectly removing the STA entry after
successful SAE commit messages. Fix this by using sae_status_success()
instead of direct check for WLAN_STATUS_SUCCESS when processing SAE
commit messages before removing station entry.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
There are 2 HW modes with IEEE80211_MODE_A: one for the 5 GHz channels
and one for 6 GHz channels. Since hw_get_chan() checks all the
compatible hw modes, eventually, an incorrect hw mode is selected.
To fix this, add a function that checks if a specific mode supports
the requested frequency and if so use it as the current mode.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Extend SPR element to support following fields and pass all
information to kernel for driver use.
* Non-SRG OBSS PD Max Offset
* SRG BSS Color Bitmap
* SRG Partial BSSID Bitmap
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Allow HE MCS rate to be used for beacon transmission when the driver
advertises the support. The rate is specified with a new beacon_rate
option "he:<HE MCS>" in hostapd configuration.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Use the correct enum nl80211_band value when configuring the beacon rate
for the 6 GHz band.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Enable user to configure Maximum MPDU Length, Maximum A-MPDU Length
Exponent, Rx Antenna Pattern Consistency, and Tx Antenna Pattern
Consistency of 6 GHz capability through config file.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
This could fail in theory if running out of memory, so better check for
this explicitly instead of allowing the exchange to continue and fail
later due to checkcode mismatch.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use more accurate INTERWORKING_EXCLUDED for this. The actual event
prefix is not changed to remains compatible with external components
using this control interface event message.
Signed-off-by: Jouni Malinen <j@w1.fi>
For EU, where preCAC is allowed, we should allow switch to DFS available
channels, instead of restarting BSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
When new credentials are configured and hostapd is reconfigured using
SIGHUP (or RELOAD on the ctrl_iface), also update the WPS credentials.
Before these changes, when WPS is triggered the Registar always serves
the credentials that were configured when hostapd started.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
This is in preparation of larger changes in hostapd_update_wps() to keep
the commits more readable.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
Some time ago it was found some drivers are setting their hw/ucode RX
filters restrictively enough to prevent broadcast DPP Action frames from
being received at upper layers in the stack.
A set of patches was introduced to the kernel and
ath9k driver as well as wpa_supplicant, e.g.,
a39e9af90 ("nl80211: DPP listen mode callback")
4d2ec436e ("DPP: Add driver operation for enabling/disabling listen mode")
However, the hostapd code itself was not calling the new multicast
registration. As such the AP side of things wasn't working as expected
in some scenarios. I've found this while trying to get ath9k working as
an AP Responder/Configurator.
The problem wasn't seen on, e.g., mac80211 hwsim driver.
Extend the wpa_supplicant mechanism to work with hostapd as well.
Signed-off-by: Michal Kazior <michal@plume.com>
In some contexts (e.g., Multi-AP) it can be useful to have access to
some of the management frames in upper layers (e.g., to be able to
process the content of association requests externally).
Add 'notify_mgmt_frames'. When enabled, it will notify the ctrl_iface
when a management frame arrives using the AP-MGMT-FRAME-RECEIVED event
message.
Note that to avoid completely flooding the ctrl_iface, not all
management frames are included (e.g., Beacon and Probe Request frames
are excluded).
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
Add option 2 to the p2p_device_random_mac_addr configuration option to
support device drivers which use by default random MAC adresses when
creating a new P2P Device interface (for instance, the BCM2711 80211
wireless device driver included in Raspberry Pi 4 Model B). In such
case, this option allows to create the P2P Device interface correctly
when using P2P permanent groups, enabling wpa_supplicant to reuse the
same MAC address when re-invoking a P2P permanent group.
update_config=1 is required.
Signed-off-by: Ircama <amacri@tiscali.it>
Messages such as RTM_IFNFO or RTM_IFANNOUNCE could have been lost.
As such, sync the state of our internal driver to the state of the
system interfaces as reports by getifaddrs(2).
This change requires the routing socket be placed in non-blocking
mode. While here, set the routing and inet sockets to close on exec.
BSDs that support SO_RERROR include NetBSD and DragonFly.
There is a review underway to add this to FreeBSD.
Signed-off-by: Roy Marples <roy@marples.name>
When the AP advertised RSNE, RSNXE, and WPA IE, hostapd incorrectly
removed the RSNE in the EAPOL-Key msg 3/4 if the STA associates with
WPA, leaving only RSNXE instead of WPA IE. WPA STA fails to connect to
such AP as the WPA IE is missing.
Since RSNXE is not really used in non-RSN connection, just remove it
here with RSNE.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This is needed to avoid the corner case of local RSNXE aware station
being configured to behave as WPA(v1)-only STA when the AP might not
include RSNXE in EAPOL-Key msg 3/4.
Signed-off-by: Jouni Malinen <j@w1.fi>
Old gcc versions complain about signed/unsigned comparison in
dpp_rx_gas_resp(). Hide it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
There's no point in attempting to configure frame filters on
a P2P-Devices that doesn't even have a netdev (nor passes any
data traffic), that just results in error messages. Skip it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add HE as an accepted option ("he") in the CHAN_SWITCH command similarly
to the way VHT is addressed.
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
This is mainly to help with fuzz testing that could generate overly long
test data that would not be possible in real use cases due to MMPDU size
limits. The implementation for storing vendor IEs with such
unrealisticly long IE buffers can result in huge number of memory
reallozations and analyzing those can be very heavy.
While the maximum length of the fuzzing test input could be limited, it
seems nicer to limit this IE storage limit instead to avoid timeouts
from fuzz test runs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Parsing and copying of WPS secondary device types list was verifying
that the contents is not too long for the internal maximum in the case
of WPS messages, but similar validation was missing from the case of P2P
group information which encodes this information in a different
attribute. This could result in writing beyond the memory area assigned
for these entries and corrupting memory within an instance of struct
p2p_device. This could result in invalid operations and unexpected
behavior when trying to free pointers from that corrupted memory.
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=27269
Fixes: e57ae6e19e ("P2P: Keep track of secondary device types for peers")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Derive the KDK as part of PMK to PTK derivation if forced by
configuration or in case both the local AP and the peer station declare
support for secure LTF.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Derive the KDK as part of PMK to PTK derivation if forced by
configuration or in case both the local station and the AP declare
support for secure LTF.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
IEEE P802.11az/D2.6 added definitions to include RSNXE in the PASN
negotiation. Implement the new functionality in both wpa_supplicant and
hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
IEEE P802.11az/D2.6 defines the following additional capabilities to
RSNXE:
- Secure LTF support
- Secure RTT support
- Protection of range negotiation and measurement management frames.
Add support for advertising the new capabilities.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Note that the implementation is not complete as it is missing support
for the FT wrapped data which is optional for the station, but must be
supported by the AP in case the station included it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add support for PASN authentication with FT key derivation:
- As IEEE P802.11az/D2.6 states that wrapped data is optional and
is only needed for further validation of the FT security parameters,
do not include them in the first PASN frame.
- PASN with FT key derivation requires knowledge of the PMK-R1 and
PMK-R1-Name for the target AP. As the WPA state machine stores PMK-R1,
etc. only for the currently associated AP, store the mapping of
BSSID to R1KH-ID for each previous association, so the R1KH-ID
could be used to derive PMK-R1 and PMK-R1-Name. Do so instead
of storing the PMK-R1 to avoid maintaining keys that might not
be used.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
As the PASN FILS authentication is only defined for FILS SK without PFS,
and to support PASN authentication with FILS, implement the PASN with
FILS processing as part of the PASN handling and not as part of the WPA
Authenticator state machine.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add PASN implementation to wpa_supplicant
1. Add functions to initialize and clear PASN data.
2. Add functions to construct PASN Authentication frames.
3. Add function to process PASN Authentication frame.
4. Add function to handle PASN frame TX status.
5. Implement the station side flow processing for PASN.
The implementation is missing support for wrapped data and PMKSA
establishment for base AKMs, and only supports PASN authentication or
base AKM with PMKSA caching.
The missing parts will be added in later patches.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
PASN requires to store the PTK derived during PASN authentication
so it can later be used for secure LTF etc. This is also true
for a PTK derived during regular connection.
Add an instance of a PTKSA cache for each wpa_supplicant
interface when PASN is enabled in build configuration.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
In order to be able to perform secure LTF measurements, both the
initiator and the responder need to first derive TK and KDK and store
them, so they would later be available for the secure LTF negotiation.
Add a basic implementation of a PTKSA cache that stores derived TK/KDK
which can later be used for secure LTF negotiation, and add it to the
build configuration.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add helper functions to construct a PASN Authentication frame and
validate its content, which are common to both wpa_supplicant and
hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
1. Add a function to derive the PTK from a PMK and additional data.
2. Add a function to calculate the MIC for a PASN frames.
3. Add a function to compute the hash of an authentication frame body.
The above are built only in case that CONFIG_PASN is enabled at build
time.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Extend the fils_pmk_to_ptk() to also derive Key Derivation
Key (KDK) which can later be used for secure LTF measurements.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Extend the wpa_pmk_r1_to_ptk() to also derive Key Derivation
Key (KDK), which can later be used for secure LTF measurements.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
