If a peer stops sending adv_service_instance, we should clear the
existing dev->info.p2ps_instance.
This commit fixes the following scenario:
When peer device stops sending adv_service_instance, wpa_supplicant did
not remove old dev->info.p2ps_instance from device's property. This
variable should be updated as per peer behavior and should be cleared
when peer stops sending this information.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
Remove the unnecessary os_free() call from p2p_deinit() since
p2p_flush() called just above this takes care of freeing
p2p->after_scan_tx and the second call here ends up being no-op
os_free(NULL) in practice.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
reports mesh peer AID to kernel.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This commit introduces a new vendor sub command
QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH and associated
attributes which aim to configure selected frequencies on which the AP
can conditionally switch onto for preferred operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 49fe2ada20 ('OpenSSL: Support
OpenSSL 1.1.0 DH opacity') started using the new accessor functions, but
used incorrect success check for the DH_set0_key() call. This resulted
in dh5_init_fixed() failures and double-free on error path if the build
was linked against OpenSSL 1.1.0. Fix this by checking DH_set0_key()
return value to be 1 for the success case.
Signed-off-by: Jouni Malinen <j@w1.fi>
These control interface event message are used by external programs, so
define them a bit more formally in the header file.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows P2P Listen to be offloaded to device to enhance power
saving.
To start P2P listen offload, from wpa_cli interface, issue the command:
p2p_lo_start <freq> <period> <interval> <count>
To stop P2P listen offload, issue the command:
p2p_lo_stop
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Provides operating frequency in EVENT_ASSOC when IBSS is joined so that
wpa_s->assoc_freq can be updated when any IBSS network is joined.
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
During the P802.11s draft development, there were separate LISTEN and
IDLE states. However, the current IEEE 802.11 standards uses only the
IDLE state while the implementation called this LISTEN. Rename the state
in the implementation to match the one used in the standard to avoid
confusion. In addition, rename OPEN_{SENT,RCVD} to OPN_{SNT,RCVD} to
match the exact spelling of these states in the standard.
Signed-off-by: Jouni Malinen <j@w1.fi>
OpenSSL 1.1.0 (master branch) apparently ended up modifying the API
after the beta 2 release that was supposed to complete the work. Mark
the variables const to fix the compilation with the modified OpenSSL
API.
Signed-off-by: Jouni Malinen <j@w1.fi>
These elements can be used for pre-standard publication testing of HE
before P802.11ax draft assigns the element ID. The payload of these
vendor specific elements is defined by the latest P802.11ax draft.
Please note that the draft is still work in progress and the element
payload is subject to change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is now annotated as be16, so use it as such in all cases instead of
first storing host byte order value and then swapping that to big endian
in other instances of the same structure. This gets rid of number of
sparse warnings.
Signed-off-by: Jouni Malinen <j@w1.fi>
driver_wired.c pulls in utils/common.h before net/if.h as a workaround
for NetBSD build. This results in IFNAMSIZ getting redefined and sparse
warning about this. Silence that warning by undefining the IFNAMSIZ
definition from common.h to allow the one from net/if.h being used. In
addition, remove duplicated inclusion of net/if.h.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of a sparse warning and also allows the compatibility of
the declarations to be verified (a missing const declaration is fixed
here as well).
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of number of sparse warnings and also allows the
compatibility of the declarations to be verified (number of missing
const declarations are fixed here as well).
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows the compiler to check that function prototypes match the
implementation. In addition, this gets rid of sparse warnings.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These are called through function pointers, so no need to make the
function symbols directly available outside this file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This converts some of the PAE code to use a design that gets rid
unnecessary warnings from sparse and allows more thorough validation of
byte order operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These are called through function pointers, so no need to make the
function symbols directly available outside this file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These little endian fields were not marked properly and the type case in
the get_unaligned_* helper macros were causing warnings from sparse.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Couple of fsts_id and llt fields were not properly swapped from host
byte order to little endian byte order used in the frames. Fix this and
use the le32 type to make this more consistent and verifiable with
sparse.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since crypto_openssl.c is now implementing couple of functions
internally, pull in the relevant header files md5.h and aes_wrap.h to
make sure the function declaration are consistent.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Freeing memory for subjectAltName in parse_cert(), will give cert_cb
pointers to freed memory zone that may already been overwritten. Memory
for subjectAltName is released in parse_cert_free().
Signed-off-by: Cedric Izoard <cedric.izoard@ceva-dsp.com>
The "Accepting Additional Mesh Peerings bit == 0" means the peer cannot
accept any more peers, so suppress attempt to open a connection to such
a peer.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This moves pairwise, group, and management group ciphers to various mesh
data structures to avoid having to hardcode cipher in number of places
through the code. While CCMP and BIP are still the hardcoded ciphers,
these are now set only in one location.
Signed-off-by: Jouni Malinen <j@w1.fi>
The AMPE element includes number of optional and variable length fields
and those cannot really be represented by a fixed struct
ieee80211_ampe_ie. Remove the optional fields from the struct and
build/parse these fields separately.
This is also adding support for IGTKdata that was completely missing
from the previous implementation. In addition, Key RSC for MGTK is now
filled in and used when configuring the RX MGTK for a peer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation was incorrect in forcing the MGTK to be used
as the IGTK as well. Define new variable for storing IGTK and use that,
if set, to configure IGTK to the driver. This commit does not yet fix
AMPE element parsing to fill in this information.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the data structures to allow variable length MGTK to be
stored for RX. This is needed as an initial step towards supporting
different cipher suites.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is initial step in fixing issues in how PMF configuration for RSN
mesh was handled. PMF is an optional capability for mesh and it needs to
be configured consistently in both hostapd structures (to get proper
RSNE) and key configuration (not included in this commit).
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 0603bcb7fe ('hostapd: Process MAC
ACLs on a station association event (SME in driver)') processes MAC ACL
on a station association event for drivers which use AP SME offload but
does not consider the scenario where the drivers offload ACL. This can
result in station disconnection, though the driver accepts the
connection. Address this by avoiding the hostapd ACL check for the
drivers offloading MAC ACL.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit also introduces a new attribute MANDATORY_FREQUENCY_LIST
which aims for AP operation in a channel that ensures best concurrency
sessions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
eloop deinit calls could trigger segmentation fault if the early error
path is hit before eloop_init() gets called.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that fst_global_init() has been called before deinitializing the
global FST context. This makes it a bit easier to handle failure paths
from initialization.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set max peer links to kernel even when wpa_supplicant MPM is used. This
sets the correct value for the "Accepting Additional Mesh Peerings bit"
in "Mesh Capability field" in "Mesh Configuration element" in the Beacon
frame.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Recent versions of engine_pkcs11 are set up to be autoloaded on demand
with ENGINE_by_id() because they don't need explicit configuration.
But if we *do* want to explicitly configure them with a PKCS#11 module
path, we should still do so.
We can't tell whether it was already initialised, but it's harmless to
repeat the MODULE_PATH command if it was.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Michael Schaller <misch@google.com>
Any data accessible from nla_data() is freed before the
send_and_recv_msgs() function returns, therefore we need to allocate
space for info.flags ourselves.
Signed-off-by: Paul Stewart <pstew@google.com>
gas_address3=1 can now be used to force hostapd to use the IEEE 802.11
standards compliant Address 3 field value (Wildcard BSSID when not
associated) even if the GAS request uses non-compliant address (AP
BSSID).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously all TX status events with wildcard BSSID were ignored. This
did not allow Public Action frame TX status to be processed with the
corrected wildcard BSSID use. Fix this to be allowed. In practice, this
affects only test cases since Action frame TX status was not used for
anything else.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11-2012, 10.19 (Public Action frame addressing) specifies
that the wildcard BSSID value is used in Public Action frames that are
transmitted to a STA that is not a member of the same BSS. hostapd used
to use the actual BSSID value for all such frames regardless of whether
the destination STA is a member of the BSS.
Fix this by using the wildcard BSSID in cases the destination STA is not
a member of the BSS. Leave group addressed case as-is (i.e., the actual
BSSID), since both values are accepted. No such frames are currently
used, though.
This version is still using the AP BSSID value in the Address 3 field
for GAS response frames when replying to a GAS request with AP BSSID
instead of Wildcard BSSID. This is left as a workaround to avoid
interoperability issues with deployed STA implementations that are still
using the non-compliant address and that might be unable to process the
standard compliant case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds the necessary changes to support extraction and use of the
extended capabilities specified per interface type (a recent
cfg80211/nl80211 extension). If that information is available,
per-interface values will be used to override the global per-radio
value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new "timeout" argument to the event message if the nl80211 message
indicates that the connection failure is not due to an explicit AP
rejection message. This makes it easier for external programs to figure
out why the connection failed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the simplest case of SAE group negotiation to occur by
selecting the next available group if the peer STA indicates the
previous one was not supported. This is not yet sufficient to cover all
cases, e.g., when both STAs need to change their groups, but at least
some cases are no covered.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd deinit functions were not ready to handle a case where the data
structures were not fully initialized. Make these more robust to allow
wpa_supplicant mesh implementation to use the current deinit design in
OOM error cases without causing NULL pointer dereferences.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids internal access of structs and also removes the dependency
on the reimplemented TLS PRF functions when EAP-FAST support is not
enabled. Notably, BoringSSL doesn't support EAP-FAST, so there is no
need to access its internals with openssl_get_keyblock_size().
Signed-Off-By: David Benjamin <davidben@google.com>
Most protocols extracting keys from TLS use RFC 5705 exporters which is
commonly implemented in TLS libraries. This is the mechanism used by
EAP-TLS. (EAP-TLS actually predates RFC 5705, but RFC 5705 was defined
to be compatible with it.)
EAP-FAST, however, uses a legacy mechanism. It reuses the TLS internal
key block derivation and derives key material after the key block. This
is uncommon and a misuse of TLS internals, so not all TLS libraries
support this. Instead, we reimplement the PRF for the OpenSSL backend
and don't support it at all in the GnuTLS one.
Since these two are very different operations, split
tls_connection_prf() in two. tls_connection_export_key() implements the
standard RFC 5705 mechanism that we expect most TLS libraries to
support. tls_connection_get_eap_fast_key() implements the
EAP-FAST-specific legacy mechanism which may not be implemented on all
backends but is only used by EAP-FAST.
Signed-Off-By: David Benjamin <davidben@google.com>
Commit 68ae4773a4 ('OpenSSL: Use library
wrapper functions to access cert store') fixed most of these, but missed
a few.
Signed-Off-By: David Benjamin <davidben@google.com>
This makes changes such that hostapd (and wpa_supplicant AP mode)
registers to kernel for specific Action frames instead of generically
registering for all Action frames. This makes it easier for other
programs to register for some Action frames that hostapd does not handle
today without having to somehow coordinate directly with hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add P2PS config flag only when config_methods are set. This restores the
pre-P2PS behavioer for the cases where Display or Keypad config method
is specified for a peer (i.e., do not add the new P2PS method in that
case).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
eap_proto_sake_errors test case where the result was used after the
failed eap_sake_compute_mic() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
eap_proto_pax_errors test case where the result was used after the
failed eap_pax_mac() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
eap_proto_fast_errors test case where the result was used after the
failed sha1_t_prf() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
wpas_ctrl_error test case where the result was used after the failed
sha256_vector() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
hostapd_oom_wpa2_eap_connect test case where the result is used after
failed md5_vector() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
hostapd_oom_wpa2_eap_connect test case where memcmp is used after failed
hmac_md5() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
hostapd_oom_wpa2_eap test case where memcmp is used after failed
md5_vector() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Check for hmac_sha256() failures and exit from wps_derive_psk() without
printing out the derived keys if anything fails. This removes a valgrind
warning on uninitialized value when running the ap_wps_m3_oom test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In some terminal, verified with gtkterm and teraterm, backspace key is
not properly processed. For instance, type 'abc', 3 times of backspace
key press then '123' shows the result of 'abc123' instead of '123'. To
fix this, add a routine to process '\b' character input when using
edit_simple.c instead of edit.c (i.e., without CONFIG_WPA_CLI_EDIT=y).
Signed-off-by: Siwon Kang <kkangshawn@gmail.com>
If there's ever a driver that, like nl80211, requires radiotap,
we need to have a NEED_RADIOTAP variable to avoid trying to link
the radiotap helpers twice. Introduce that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Commit 4104267e81 ('Fix memory leak on NFC
DH generation error path') modified the generic (non-OpenSSL)
implementation of dh5_init() to free the previously assigned public key,
if any. However, that commit did not modify the OpenSSL specific version
of this function. Add the same change there to maintain consistent
behavior between these two implementations of the same function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 4104267e81 ('Fix memory leak on NFC
DH generation error path') modified dh5_init() behavior in the
non-OpenSSL implementation to free the public key (if any was previously
set). However, this did not update one of the callers to make sure the
publ argument in the call is initialized. This could result in trying to
free invalid pointer and segmentation fault when hostapd or
wpa_supplicant was built against some other crypto library than OpenSSL.
Signed-off-by: Rujun Wang <chinawrj@gmail.com>
BoringSSL added OpenSSL 1.1.0's SSL_get_client_random() and friends in
working towards opaquifying the SSL struct. But it, for the moment,
still looks more like 1.0.2 than 1.1.0 and advertises
OPENSSL_VERSION_NUMBER as such. This means that there is no need to
define those in BoringSSL and defining them causes conflicts. (C does
not like having static and non-static functions with the same name.)
As requested, this is conditioned on defined(BORINGSSL_API_VERSION) so
wpa_supplicant may continue to support older BoringSSLs for a time.
(BoringSSL revisions without the accessors predate BoringSSL maintaining
a BORINGSSL_API_VERSION.)
Also add a missing opensslv.h include. tls_openssl.c is sensitive to
OPENSSL_VERSION_NUMBER, so it should include the header directly rather
than rely on another header to do so.
Signed-off-by: David Benjamin <davidben@google.com>
Spurious newlines output while writing the config file can corrupt the
wpa_supplicant configuration. Avoid writing these for the network block
parameters. This is a generic filter that cover cases that may not have
been explicitly addressed with a more specific commit to avoid control
characters in the psk parameter.
Signed-off-by: Paul Stewart <pstew@google.com>
WPA/WPA2-Personal passphrase is not allowed to include control
characters. Reject a Credential received from a WPS Registrar both as
STA (Credential) and AP (AP Settings) if the credential is for WPAPSK or
WPA2PSK authentication type and includes an invalid passphrase.
This fixes an issue where hostapd or wpa_supplicant could have updated
the configuration file PSK/passphrase parameter with arbitrary data from
an external device (Registrar) that may not be fully trusted. Should
such data include a newline character, the resulting configuration file
could become invalid and fail to be parsed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
One of supported code paths already allows this scenario. It is used if
driver doesn't report NL80211_ATTR_DEVICE_AP_SME and doesn't support
monitor interface. In such situation:
1) We don't quit if subscribing for WLAN_FC_STYPE_PROBE_REQ fails
2) We don't try subscribing for WLAN_FC_STYPE_ACTION
3) We fallback to AP SME mode after failing to create monitor interface
4) We don't quit if subscribing for WLAN_FC_STYPE_PROBE_REQ fails
Above scenario is used, e.g., with brcmfmac. As you can see - thanks to
events provided by cfg80211 - it's not really required to receive Probe
Request or action frames.
However, the previous implementation did not allow using hostapd with
drivers that:
1) Report NL80211_ATTR_DEVICE_AP_SME
2) Don't support subscribing for PROBE_REQ and/or ACTION frames
In case of using such a driver hostapd will cancel setup after failing
to subscribe for WLAN_FC_STYPE_ACTION. I noticed it after setting flag
WIPHY_FLAG_HAVE_AP_SME in brcmfmac driver for my experiments.
This patch allows working with such drivers with just a small warning
printed as debug message.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
This reduces duration that private keying material might remain in the
process memory by clearing wpabuf data used in WPS operations when there
is possibility of the buffer including keys or related material.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new parameter allows hostapd to add Vendor Specific elements into
(Re)Association Response frames similarly to the way vendor_elements
parameter can be used for Beacon and Probe Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The OpenSSL 1.1.0 Beta 2 release made DH opaque and that broke
compilation of crypto_openssl.c. Fix this by using the new accessor
functions when building against OpenSSL 1.1.0 or newer.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 66d464067d ('FT: Register RRB
l2_packet only if FT-over-DS is enabled') disabled RRB l2_packet socket
if ft_over_ds is disabled, but this socket is required for FT
over-the-air, too (FT key distribution). Enable the socket regardless of
ft_over_ds setting if FT is enabled.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
This adds QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION and the attributes used
with these commands.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows local GO to fetch the P2P Interface Address of a P2P Client
in the group based on the P2P Device Address for the client. This
command should be sent only on a group interface (the same peer may be
in multiple concurrent groups).
Usage:
P2P_GROUP_MEMBER <P2P Device Address>
Output:
<P2P Interface Address>
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Trigger an event when wpa_supplicant accepts an invitation to re-invoke
a persistent group. Previously wpa_supplicant entered group formation
without triggering any specific events and it could confuse clients,
especially when operating with a driver that does not support
concurrency between P2P and infrastructure connection.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
The os_snprintf() call here cannot really fail in practice, but since
its result was stored into the local variable and not checked, static
analyzers could warn about the unused assignment. Clean this up by
checking the return value.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set the global RRM flag if global RRM is supported by the device. Also,
allow RRM in (Re)Association Request frame if the global RRM flag is
set.
Signed-off-by: Beni Lev <beni.lev@intel.com>
This flag indicates that RRM can be used in (Re)Association Request
frames, without supporting quiet period.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Register to receive Radio Measurement Request frames since LCI request
is supported by wpa_supplicant.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add FTM range request via RRM. The AP sends Radio measurement request
with FTM range request as a request for the receiving STA to send FTM
requests to the given list of APs. The neighbor report part of the
request is taken from the neighbor database.
The control interface command is:
REQ_RANGE <dst addr> <rand_int> <min_ap> <responder> [<responder>..]
dst addr: MAC address of an associated STA
rand_int: Randomization Interval (0..65535) in TUs
min_ap: Minimum AP Count (1..15); minimum number of requested FTM ranges
between the associated STA and the listed APs
responder: List of BSSIDs for neighboring APs for which a measurement
is requested
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a hostapd control interface command REQ_LCI to request LCI from an
associated station using radio measurement.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Save RM enabled capability element of an associating station if radio
measurement is supported in its capability field.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Process Neighbor Report Request frame and send Neighbor Report Response
frame based on the configured neighbor report data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a configurable neighbor database that includes the content of
Nighbor Report element, LCI and Location Civic subelements and SSID.
All parameters for a neighbor must be updated at once; Neighbor Report
element and SSID are mandatory, LCI and civic are optional. The age of
LCI is set to the time of neighbor update.
The control interface API is:
SET_NEIGHBOR <BSSID> <ssid=SSID> <nr=data> [lci=<data>] [civic=<data>]
To delete a neighbor use:
REMOVE_NEIGHBOR <BSSID> <SSID>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Extend the radio_measurements parameter to save all the supported
RRM capabilities as it's used in RM enabled capabilities element.
Make this parameter not directly configurable via config file (though,
keep the radio_measurements parameter for some time for backwards
compatibility). Instead, add a configuration option to enable neighbor
report via radio measurements. Other features can be added later as
well.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a function that parses SSID in text or hex format. In case of the
text format, the SSID is enclosed in double quotes. In case of the hex
format, the SSID must include only hex digits and not be enclosed in
double quotes. The input string may include other arguments after the
SSID.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Make the function available as part of the wpabuf API.
Use this renamed function where possible.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
The hostapd "POLL_STA <addr>" control interface command can be used to
check whether an associated station ACKs a QoS Data frame. The received
ACK for such a frame is reported as an event message ("AP-STA-POLL-OK
<addr>").
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The optional tx=0 parameter can be added to the hostapd
DEAUTHENTICATE/DISASSOCIATE command to request disconnection without
transmitting the Deauthentication/Disassociation frame to the STA.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external programs to fetch the driver inactivity value for a
specific STA ("STA <addr>" hostapd control interface command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new VENDOR_ELEM value 14 can now be used to add a vendor element
into Probe Request frames used by non-P2P active scans.
For example:
VENDOR_ELEM_ADD 14 dd05001122330a
and to clear that:
VENDOR_ELEM_REMOVE 14 *
Signed-off-by: Jouni Malinen <j@w1.fi>
Implement configure_data_frame_filters() callback by using
the net-sysfs interfaces (if these are available).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add a new function declaration that will allow wpa_supplicant to request
the driver to configure data frame filters for specific cases.
Add definitions that will allow frame filtering for stations as
required by Hotspot 2.0:
1. Gratuitous ARP
2. Unsolicited NA
3. Unicast IP packets encrypted with GTK
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
If a legacy client with no P2P PS support is trying to connect to
a P2P GO, the driver should know that, and change its PS behavior
accordingly.
Add a parameter to hostapd_sta_add_params() indicating if P2P PS is
supported by the station and pass this parameter to kernel with nl80211
driver when the station is added/set.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Fix a possible memory leak in decode_tunnel_passwords() if an invalid
passphrase is received from the RADIUS server.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
This was previously handled for the case where the non-success
Invitation Response frame was sent out during the Listen phase. However,
in the case the Action frame TX ended up getting scheduled when the
Search phase scan had already started (e.g., due to the driver reporting
Invitation Request RX late enough for the Listen-to-Search transition
having already started), the postponed Action frame TX status processing
did not cover the specific case of non-success Invitation Response. This
could result in the p2p_find operation getting stopped (stuck in SEARCH
state) unexpectedly.
Fix this by calling p2p_check_after_scan_tx_continuation() from
Invitation Response TX callback handler if the invitation was rejected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The Secure bit in the Key Information field of EAPOL-Key frames is
supposed to be set to 1 when there is a security association. This was
done for other frames, but not for the EAPOL-Key Request frame where
supplicant is requesting a new PTK to be derived (either due to Michael
MIC failure report Error=1 or for other reasons with Error=0). In
practice, EAPOL-Key Request frame is only sent when there is a PTK in
place, so all such frames should have Secure=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
This struct in the union is empty, but the design of using a zero-length
u8 array here is not fully compatible with C++ and can result in
undesired compiler warnings. This struct is not used anymore, so it can
be removed from the struct ieee80211_mgmt definition to complete the
changes started in commit d447cd596f
('Updates for stricter automatic memcpy bounds checking').
Signed-off-by: Jouni Malinen <j@w1.fi>
This struct in the union is empty, but the design of using a zero-length
u8 array here is not fully compatible with C++ and can result in
undesired compiler warnings. Since there are no non-IE fields in the
Probe Request frames, get the location of the variable length IEs simply
by using the pointer to the frame header and the known header length.
Signed-off-by: Jouni Malinen <j@w1.fi>
This struct in the union is empty, but the design of using a zero-length
u8 array here is not fully compatible with C++ and can result in
undesired compiler warnings. Since there are no non-IE fields in the
Probe Request frames, get the location of the variable length IEs simply
by using the pointer to the frame header and the known header length.
Signed-off-by: Jouni Malinen <j@w1.fi>
This reverts commit 4ca16b5fd7.
Configuration for this will be done using a previously assigned more
generic command. This new command
QCA_NL80211_VENDOR_SUBCMD_SET_TXRX_AGGREGATION has not been used in any
driver version and won't be used, so the assigned command id can be
freed for future use.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no strong need for pulling in linux/if_ether.h here since all
that is needed if ETH_P_IP and we already cover multiple other ETH_P_*
values in utils/common.h.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was only used for providing an option to use linux/if_packet.h
instgead of netpacket/packet.h in src/ap/iapp.c. However,
netpacket/packet.h is nowadays commonly available and hostapd already
depends on it through src/l2_packet/l2_packet_linux.c, so there is no
need to continue to provide this option for the kernel header.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of need to include linux/if_vlan.h and additional defines
in vlan_ioctl.c to avoid issues with missing definitions in libc
headers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Due to both <netinet/in.h> (in "utils/includes.h") and <linux/in6.h> (in
<linux/if_bridge.h>) being included, the in6_addr is being redefined:
once from the C library headers and once from the Linux kernel headers.
This causes some build failures with for example the musl C library:
In file included from /usr/include/linux/if_bridge.h:18,
from ../src/ap/vlan_init.c:17:
/usr/include/linux/in6.h:32: error: redefinition of 'struct in6_addr'
/usr/include/linux/in6.h:49: error: redefinition of 'struct sockaddr_in6'
/usr/include/linux/in6.h:59: error: redefinition of 'struct ipv6_mreq'
Mixing C library and Linux kernel headers is a bit problematic [1] and
should be avoided if possible [2]. In order to fix this, define just the
macros needed from <linux/if_bridge.h> as done in Busybox for the brctl
applet [3].
[1] https://sourceware.org/bugzilla/show_bug.cgi?id=15850
[2] http://www.openwall.com/lists/musl/2015/10/06/1
[3] https://git.busybox.net/busybox/commit/?id=5fa6d1a632505789409a2ba6cf8e112529f9db18
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
With this, vlan_init.c does not need any special header files anymore
and vlan_ifconfig.c does not need hostapd-specific header files that
might conflict with net/if.h on NetBSD.
Signed-off-by: Jouni Malinen <j@w1.fi>
Move the ioctl-based VLAN implementation to a separate file to avoid
need for conditional blocks within vlan_ioctl.c. This removes the
internal CONFIG_VLAN_NETLINK define, i.e., this is now used only in
build configuration (.config) to select whether to include the
vlan_util.c (netlink) or vlan_ioctl.c (ioctl) implementation of the
functions.
Signed-off-by: Jouni Malinen <j@w1.fi>
caddr_t is legacy BSD and should be avoided [1]. While glibc may still
use __caddr_t as the type, Linux kernel does not (it is "void __user *
ifru_data").
This fixes compile errors with the musl libc:
../src/ap/vlan_init.c: In function 'br_delif':
../src/ap/vlan_init.c:218:18: error: '__caddr_t' undeclared (first use in this function)
ifr.ifr_data = (__caddr_t) args;
[1] http://stackoverflow.com/questions/6381526/what-is-the-significance-of-caddr-t-and-when-is-it-used
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
cfg80211 reports a deauth/disassoc event when internally clearing
connection with the previous BSS. Ignore that event to allow the new
connect command to complete.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier for drivers that use the Connect command instead of
separate Auth+Assoc commands to determine when to use reassociation
instead of association. Matching changes are still needed in cfg80211 to
allow this parameter to be used, but it is safe for wpa_supplicant to
start including this attribute now since it will be ignored by older
cfg80211 versions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
pmksa->pmk or pmksa->pmkid cannot be NULL since they are arrays. Remove
the unnecessary NULL checks and use the provided pmksa pointer directly
to simplify the implementation. (CID 138519)
Signed-off-by: Jouni Malinen <j@w1.fi>
Interface additions/removals are not guaranteed to be for the driver
listening to the kernel events. As such, send the events to
wpa_supplicant_event_global() which can then pick the correct interface
registered with wpa_supplicant to send the event to.
Signed-off-by: Roy Marples <roy@marples.name>
Commit 1889af2e0f ('VLAN: Separate station
grouping and uplink configuration') added an ap_sta_set_vlan() function
that gets called from pmksa_cache_auth.c. This broke CONFIG_IBSS_RSN=y
build if src/ap/sta_info.c did not get included in the build, i.e., if
CONFIG_AP=y was not set.
Fix this by making the ap_sta_set_vlan() call conditional on
CONFIG_NO_VLAN being undefined and define this for CONFIG_IBSS_RSN=y
builds. This is fine for wpa_supplicant since CONFIG_AP=y case was
already defining this. For hostapd, this function call is not needed for
CONFIG_NO_VLAN case either.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This patch add functionality of mesh SAE PMKSA caching. If the local STA
already has peer's PMKSA entry in the cache, skip SAE authentication and
start AMPE with the cached value.
If the peer does not support PMKSA caching or does not have the local
STA's PMKSA entry in the cache, AMPE will fail and the PMKSA cache entry
of the peer will be removed. Then STA retries with ordinary SAE
authentication.
If the peer does not support PMKSA caching and the local STA uses
no_auto_peer=1, the local STA can not retry SAE authentication because
NEW_PEER_CANDIDATE event cannot start SAE authentication when
no_auto_peer=1. So this patch extends MESH_PEER_ADD command to use
duration(sec). Throughout the duration, the local STA can start SAE
authentication triggered by NEW_PEER_CANDIDATE even though
no_auto_peer=1.
This commit requires commit 70c93963ed
('SAE: Fix PMKID calculation for PMKSA cache'). Without that commit,
chosen PMK comparison will fail.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA_FLUSH control interface command to
allow the PMKSA list from the authenticator side to be flushed for AP
and mesh mode. In addition, this adds a hostapd PMKSA_FLUSH control
interface command to flush the PMKSA entries.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA control interface command to allow
the PMKSA list from the authenticator side to be listed for AP and mesh
mode. In addition, this adds a hostapd PMKSA control interface command
to show the same list for the AP case.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This group capability bit was previously added unconditionally which
could result in the P2P Client assuming the functionality is available
even though the GO would always reject the request (not reply to it with
an assigned IP address) during the 4-way handshake.
Fix this by advertising the capability only if the GO configuration
allow IP address assignment to be completed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 732b1d20ec ('nl80211: Clean up
ifidx properly if interface in a bridge is removed') added
drv->if_indices_reason array similarly to the previously used
drv->if_indices. However, it had a copy-paste error here on the error
path where a reallocation failure after at least one successful
reallocation would result in the drv->if_indices being overridden
instead of restoring drv->if_indices_reason to the old value. Fix this
by setting the correct variable on the error path. (CID 138514)
Signed-off-by: Jouni Malinen <j@w1.fi>
SMPS mode is applicable only for HT and including an attribute to
configure it when HT is disabled could result in the AP start operation
failing. Fix this by adding the attribute only in cases where HT is
enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since this function needs to allocate memory, it might fail. Check that
the returned memory pointer is not NULL before trying to parse the
output.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While this function could return NULL if the parameter issued to it were
NULL, that does not really happen here. Anyway, since this can result in
a warning from a static analyzer that does can see the return NULL
without fully understanding what it means here, check the return value
explicitly against NULL to avoid false warnings.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since commit cb05808c46 ('nl80211: Generic
Linux master interface support for hostapd'), hostapd is listening for
EAPOL frames on any master which the interface is enslaved under.
This commit allows hostapd to support network hierarchy in which the
interface is enslaved under some master which in turn is enslaved under
a bridge.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
In scenarios where only DFS channels are available (e.g., outdoor,
special country codes), hostapd must be able to handle situations
where all are unavailable.
The two possibilities to get there are
1) while operating on the last available DFS channel a radar is
detected
2) hostapd is started while all channels are unavailable
In both cases, hostapd instead of terminating should better
wait for the NOPs to pass and re-try operation after the CAC.
This patch provides that feature by using the condition
(iface->state == HAPD_IFACE_DFS && !iface->cac_started)
as NOP mode signature to retry operation from within
hostapd_dfs_nop_finished().
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Upon receiving FST setup request on old band, the peer is searched on
new band. The assumption is that MB IE from this peer on new band
previously received either in assoc event or in FST setup request.
There are cases in which above assumption doesn't work, peer is not
found and session setup fails. For example:
- STA connects over 11ac. Due to driver limitation, MB IE is not included
in assoc event
- STA connects over 11ad. MB IE included in assoc event.
- FST session established on 11ac band, with AP as initiator. i.e. FST
setup request sent in AP=>STA direction. STA searches for peer's (AP)
MB IE on 11ad band which exists.
- FST switch occur
- FST session established on 11ad band, with STA as initiator. i.e. FST
setup request sent in STA=>AP direction. AP searches for peer's (STA)
MB IE on 11ac band which are absent.
For fixing the above, consider also peers without MB IE as candidates in
the search algorithm.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
In the 60 GHz band, service discovery management frames are sent over
the control PHY and have a smaller maximum frame size (IEEE Std
802.11ad-2012, 21.4.3.2). Fix the code to use sufficiently small
fragment size when operating in the 60 GHz band.
The 60 GHz fragment size (928) is derived from the maximum frame size
for control PHY (1023) and subtracting 48 bytes of header size, and some
spare so we do not reach frames with the absolute maximum size.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Add a new 'use_driver_iface_addr' configuration parameter to allow use
of the default interface address generated by the driver on interface
creation. This can be useful when specific MAC addresses were allocated
to the device and we want to use them for multi-BSS operation.
Signed-off-by: Eliad Peller <eliad@wizery.com>
There is a race condition in which AP might receive the EAPOL-Start
frame (from the just-associated station) before the TX completion of the
Association Response frame. This in turn will cause the EAPOL-Start
frame to get dropped, and potentially failing the connection.
Solve this by saving EAPOL frames from authenticated-but-not-associated
stations, and handling them during the Association Response frame TX
completion processing.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Add UDP support for ctrl_iface:
New config option could be set:
CONFIG_CTRL_IFACE=udp
CONFIG_CTRL_IFACE=udp-remote
CONFIG_CTRL_IFACE=udp6
CONFIG_CTRL_IFACE=udp6-remote
And hostapd_cli usage:
hostapd_cli -i localhost:8877
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This is preparation for sharing a single implementation for ctrl_iface
functionality in wpa_supplicant and hostapd.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Update the peer WFD IE information based on WFD elements received in
Provision Discovery Response and GO Negotiation Response frames.
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
In case a Probe Request frame is received from a known peer P2P Device,
update the listen channel based on the P2P attributes in the Probe
Request frame. This can be useful for cases where the peer P2P Device
changed its listen channel, and the local P2P device is about to start a
GO Negotiation or invitation signaling with the peer.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Currently, when scan is stuck in the kernel/driver/fw,
the nl80211 driver tries to recover by faking a SCAN_RESULTS flow.
However, the scan is still stuck in the kernel/driver/fw.
To avoid that stuck request, abort it upon scan timeout.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
syms is defined only for WPA_TRACE_BFD:
../src/utils/trace.c: In function ‘wpa_trace_deinit’:
../src/utils/trace.c:372:7: error: ‘syms’ undeclared (first use in this function)
free(syms);
^
../src/utils/trace.c:372:7: note: each undeclared identifier is reported only once for each function it appears in
make: *** [../src/utils/trace.o] Error 1
make: *** Waiting for unfinished jobs....
Add appropriate #ifdef.
Signed-off-by: Eliad Peller <eliad@wizery.com>
When building P2P IE for Probe Request frames in P2P scan, add the
device information attribute if the 60 GHz band is included in the scan,
since this is required by the P2P specification.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Expose the functions wpas_get_bands() and wpas_freq_to_band() and the
enum wpa_radio_work_band, since they will be needed outside
wpa_supplicant.c.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
STT guards the exchange of FST Action frames with the peer station.
It was observed that sometimes Action frames sending is delayed at
driver/FW layers for few hundreds millisec.
Enlarge the STT to overcome such cases.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
In case vendor ACS command returns invalid channel or hardware mode,
complete the interface setup with an error code instead of simply
return, so that hostapd can properly clean up the interface setup.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This tells to the server how long we have been trying to transmit the
message so that the actual time of the message generation can be
determined from receive time (ignoring network delays and only at
accuracy of one second).
For interim updates, only value 0 is used since there are no
retransmissions of the same message. For other accounting messages, the
initial attempt goes out with value 0 and the retransmissions, if
needed, show the number of seconds the message has been waiting in the
queue.
Update the Identifier and Authenticator in the messages whenever
updating the Acct-Delay-Time per RFC 2866, 4.1 requirements.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of using the RADIUS client retransmission design with the old
RADIUS message contents for each retry, trigger a completely new interim
accounting update instance more quickly (using the same schedule as
RADIUS message retransmissions) to improve accounting updates in cases
where RADIUS message delivery fails. This allows the server to get up to
date information from the time the "retry" message was sent instead of
the old information from the time the first failed attempt was sent.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to maintain two implementations of the functionality.
is_zero_ether_addr() is easier to understand, so use it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Using rtnl_link_alloc_cache() is expensive as it fills in all configured
links. Using rtnl_link_get_kernel() is much more lightweight.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
When an interface is removed while it was in a bridge, the bridge was
not removed from the local ifidx list.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
As the Linux variant of l2_packet_init() does not use its own_addr
argument and l2_packet_receive() does not filter on destination MAC
address, this needs to be checked in the callback.
If there are multiple BSSes listening for FT RRB packets, all their
BSSIDs need to be local to the bridge interface. As l2_packet_init() is
going to receive all of them going for any local address, those RRB
messages started turning up on BSSes that were not destinated for and
cluttering logs.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
If the AP is slow, passphrase hashing takes too long to serve the client
before timeout. Extend the Tunnel-Password design to allow a 64
character value to be interpreted as a PSK and send SSID to RADIUS
server. This allows the RADIUS server to either take care of passphrase
hashing or to use raw PSK without such hashing.
This is especially important for FT-PSK with FT-over-air, where hashing
cannot be deferred.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Instead of copying the full struct hostapd_sta_wpa_psk_short, share the
existing entry and use reference counting to check when it needs to be
freed. This allows caching of PSKs derived from passphrases to avoid
having to perform the heavy hashing operation multiple times.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Hashing takes quite some time (can be about one second on a low-power
CPU for each passphrase provided), so hostapd can easily hit the 900 ms
Wi-Fi client authentication deadline (mac80211 uses 3x 300 ms). This can
be fixed by storing the passphrase instead of PSK with the STA and defer
the hashing into the WPA/RSN 4-way handshake, when enumerating all PSKs.
This applies for the case where a RADIUS server is used to store the
per-STA passphrases and this passphrase is delivered as part of the MAC
ACL check during IEEE 802.11 Authentication frame processing.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The VLAN ifname is limited to the maximum length of IFNAMSIZ, so there
is no need to use heap allocation for it.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
r1_key_holder is an identifier that was always set to zero if unless
configured before.
See 11.6.1.7.4 of IEEE Std 802.11-2012 which reads
"R1KH-ID is a MAC address of the holder of the PMK-R1 in the
Authenticator of the AP"
See 12.2.2 of IEEE Std 802.11-2012 which reads
"Each R0KH-ID and R1KH-ID is assumed to be expressed as a unique
identifier within the mobility domain."
"The R1KH-ID shall be set to a MAC address of the physical entity
that stores the PMK-R1 ..."
Defaulting this to BSSID is a more reasonable value since we have not
rejected the missing r1_key_holder as invalid configuration.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
A malicious station could try to do FT-over-DS with a non WPA-enabled
BSS. When this BSS is located in the same hostapd instance, internal RRB
delivery will be used and thus the FT Action Frame will be processed by
a non-WPA enabled BSS. This processing used to crash hostapd as
hapd->wpa_auth is NULL. If the target BSS is on a different hostapd
instance, it will not listen for these packets and thus not crash.
Fix this by checking hapd->wpa_auth before delivery.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The FT RRB hostapd packets have a length field. For PULL frames, it
counted the bytes starting with nonce and up to the last before pad. For
RESP frames, it counted the bytes starting with nonce and up to the last
before pad except for 2 bytes. For PUSH frames, it counted the bytes
starting with nonce and up to including pad.
As rounding is done with AES encryption, including pad does not make
sense. Not including the last field before pad does not make sense
either. These were broken in the earlier addition of the 2 octet
pairwise field in commit 1b484d60e5 ('FT:
Include pairwise cipher suite in PMK-R0 SA and PMK-R1 SA').
AES encryption is not affected, as rounding hides the differences. The
packets data_length field is not used, so the differences have no effect
there.
This patch changes the constants to match the bytes used, thus excluding
the pad. To validate the changes, look at remainder modulo 8 of the sum
of the size constants and the padding sizes.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This makes hostapd track Supported Operating Classes information from
the associated STAs. The stored information is available through the STA
control interface command (supp_op_classes row) as a hexdump of the
Supported Operating Classes element starting from the Length field. This
information can be used as input to BSS transition management and
channel switching decisions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Inside management frame TX status callback, print the TX result where it
was missing. This is useful for debugging management frame drops.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
This adds parsing of non-preferred channel list on an MBO AP. The
information in (Re)Association Request and WNM Notification Request
frames is parsed to get the initial value and updates from each
associated MBO STA. The parsed information is available through the STA
control interface command non_pref_chan[i] rows.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the second memory allocation in ieee802_11_send_wnmsleep_resp() were
to fail and ieee80211_11_get_tfs_ie() succeed, the wnmtfs_ie allocation
would not have been freed on the error path.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While refactoring VLAN comparison into vlan_compare(), it was overlooked
that modifications are needed for tagged VLAN support.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
If WPA2 and MBO are enabled, PMF needs to be enabled in hostapd
configuration. If PMF is optional in the configuration, an MBO STA is
required to negotiate use of PMF.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes hostapd parse a received WNM Notification Request frame
subelements and if a WFA MBO cellular data capability subelement is
seen, update the cellular data capability for the STA.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes hostapd parse the MBO attribute in (Re)Association Request
frame and track the cellular data capability (mbo_cell_capa=<val> in STA
control interface command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This removes multiple copies of wpabuf_resize() following by
wpabuf_put_{buf,data}() with the help of two simple helper functions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add an option to add MBO IE to BSS Transition Management Request frame.
The MBO IE includes the transition reason code, cellular data connection
preference, and, if the disassoc imminent bit is set, it may also
include re-association retry delay. Otherwise, the re-association retry
delay should be set to zero.
The additional BSS_TM_REQ argument uses the following format:
mbo=<reason>:<reassoc delay>:<cell pref>
reason: 0-9
reassoc delay: 0-65535 (seconds; 0 = disabled)
cell pref: 0, 1, 255
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add MBO IE with AP capability attribute to Beacon, Probe Response, and
(Re)Association Response frames to indicate the AP supports MBO.
Add option to add Association Disallowed attribute to Beacon, Probe
Response, and (Re)Association Response frames. Usage:
SET mbo_assoc_disallow <reason code>
Valid reason code values are between 1-5. Setting the reason code to
0 will remove the Association Disallowed attribute from the MBO IE
and will allow new associations.
MBO functionality is enabled by setting "mbo=1" in the config file.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add the transition candidate list to BSS Transition Management Response
frame. The candidates preference is set using the regular wpa_supplicant
BSS selection logic. If the BSS transition request is rejected and
updated scan results are not available, the list is not added.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a function to derive phy type from frequency and bandwidth
as defined in IEEE Std 802.11ac-2013 Annex C (dot11PHYType).
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add parsing of MBO IE in BSS Transition Management Request frames. If
the MBO IE includes the association retry delay attribute, do not try to
reconnect to the current BSS until the delay time is over.
If the MBO IE includes the cellular data connection preference attribute
or the transition rejection reason attribute, send a message to upper
layers with the data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add definitions for global operating classes. These definitions will be
used to construct supported operating classes information element.
The operating classes definitions used locally for P2P module will be
removed and included in the general operating classes definitions.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a helper function to find a certain IE inside IEs buffer by ID and
use this function in several places that implemented similar
functionality locally.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The recent VLAN changes added an explicit code path that sets vlan_desc
= NULL within ap_sta_set_vlan(). This makes some code analyzers warn
about the debug print that could potentially dereference this pointer.
Silence that warning by verifying the pointer more consistently within
this function.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the driver supports 64-bit TX/RX byte counters, use them directly.
The old 32-bit counter extension is maintained for backwards
compatibility with older drivers.
For nl80211 driver interface, the newer NL80211_STA_INFO_RX_BYTES64 and
NL80211_STA_INFO_TX_BYTES64 attributes are used when available. This
resolves the race vulnerable 32-bit value wrap/overflow. Rework RADIUS
accounting to use these for Acct-Input-Octets, Acct-Input-Gigawords,
Acct-Output-Octets, and Acct-Output-Gigawords, these values are often
used for billing purposes.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Previously, stations were added to the driver only after the
(Re)Association Response frame was acked. In the time period between the
station has acked the (Re)Association Response frame and the time the
station was added to the kernel, the station can already start sending
Data frames, which will be dropped by the hardware/driver. In addition
to the data loss, the driver may ignore NDPs with PM bit set from this
STA.
Fix this by setting/adding the STA with associated flag set to the
driver before the AP sends the (Re)Association Response frame with
status success. If the (Re)Association Response frame wasn't acked,
remove the station from the driver.
Note that setting a station to associated state before the non-AP
station acknowledges the (Re)Association Response frame is not compliant
with the IEEE 802.11 standard that specifically states that a non-AP
station should transition to authenticated/associated state only after
it acknowledged the (Re)Association Response frame. However, this is a
justifiable simplification to work around the issue described above since
1. The station will be removed in case it does not acknowledge the
(Re)Association Response frame.
2. All Data frames would be dropped until the station is set to
authorized state and there are no known issues with processing the
other Class 3 frames during the short window before the
acknowledgement is seen.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add support for drivers that support full AP client state, i.e., can
handle adding stations that are not associated yet. For such drivers,
add a station after processing the authentication request, instead of
adding it in the association response callback.
Doing so is beneficial in cases where the driver cannot handle the add
station request, in which case it is useless to perform the complete
connection establishment.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
This provides means for determining whether the driver supports full AP
station state and setting the needed STA flags for using this
functionality.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Do not use os_random() that uses a low quality PRNG to generate the
anti-clogging token. The construction can be improved upon by replacing
it with a call to os_get_random(), which uses a high quality PRNG. While
the RFC 5931 explictly recommends not to do this ("SHOULD NOT be from a
source of random entropy"), it does still mandate unpredicability ("MUST
be unpredictable"). The anti-clogging token is most unpredictable when
it is taken from a high quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Remove the fallback dependency on os_random() from the code that gets a
valid DFS channel. This is exceptionally unlikely to ever be called as
the call to os_get_random() is unlikely to fail. The intention is to
facilitate future removal of os_random() as it uses a low quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Remove the fallback dependency on os_random() when generating a WPS pin.
This is exceptionally unlikely to ever be called as the call to
os_get_random() is unlikely to fail. The intention is to facilitate
future removal of os_random() as it uses a low quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Do not use the system clock or os_random() that uses a low quality PRNG
as part of the pseudo-random challenge in auth_shared_key(). The
construction can be improved upon by replacing it with a call to
os_get_random(), which uses a high quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Previously, only mesh Action frames from BLOCKED STA were dropped.
Extend that to drop Authentication frames as well.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The SAE PMKID is calculated with IEEE Std 802.11-2012 11.3.5.4, but the
PMKID was re-calculated with 11.6.1.3 and saved into PMKSA cache. Fix
this to save the PMKID calculated with 11.3.5.4 into the PMKSA cache.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Ensure that characters are represented as unsigned char when using
isblank() and isspace(). These function take in a "int c" argument, but
it needs to be unsigned for the cases where EOF is not indicated.
Signed-off-by: Roy Marples <roy@marples.name>
Shuffle includes above system ones so to fix a compile issue
on NetBSD where the if_type #define from <net/if.h>
conflicts with the wpa_driver_if_type enum.
Signed-off-by: Roy Marples <roy@marples.name>
Shuffle wpa_supplicant includes above system ones so that
to fix a compile problem on NetBSD where if_type #define
conflicts with the wpa_driver_if_type enum.
Signed-off-by: Roy Marples <roy@marples.name>
While most C libraries print "(null)" when NULL is used as an argument
to printf format string %s, this is not really necessary to print here,
so move the debug print to be after the NULL check.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the stations to be assigned to their own vif. It does not
need dynamic_vlan to be set. Make hostapd call ap_sta_set_vlan even if
!vlan_desc.notempty, so vlan_id can be assigned regardless.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This makes vlan_newlink() and vlan_dellink() add tagged VLANs to AP_VLAN
interfaces as given by struct vlan_description.
hostapd_vlan_if_remove() is done in vlan_dellink() as tagged interfaces
need to be removed before the interface can be deleted and a DELLINK
message can be generated.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
To prepare for adding tagged VLAN support in vlan_init.c, vlan_newlink()
and vlan_dellink() are split into multiple functions. This reduces
indention and eases adding tagged VLANs as well.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
1. Add tagged VLAN to struct vlan_description
(compile limited number of tagged VLANs per description)
For k tagged VLANs, the first k entries in vlan_description.tagged
are used. They are sorted in ascending order. All other entries are
zero. This way os_memcmp() can find identical configurations.
2. Let tagged VLANs be parsed from RADIUS Access-Accept
3. Print VLAN %d+ with %d=untagged VID if tagged VLANs are set
4. Select an unused vlan_id > 4096 for new tagged VLAN configurations
5. Add EGRESS_VLAN RADIUS attribute parsing also for untagged VLANs
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Separate uplink configuration (IEEE 802.1q VID) and grouping of stations
into AP_VLAN interfaces.
The int vlan_id will continue to identify the AP_VLAN interface the
station should be assigned to. Each AP_VLAN interface corresponds to an
instance of struct hostapd_vlan that is uniquely identified by int
vlan_id within an BSS.
New: Each station and struct hostapd_vlan holds a struct
vlan_description vlan_desc member that describes the uplink
configuration requested. Currently this is just an int untagged IEEE
802.1q VID, but can be extended to tagged VLANs and other settings
easily.
When the station was about to be assigned its vlan_id, vlan_desc and
vlan_id will now be set simultaneously by ap_sta_set_vlan(). So
sta->vlan_id can still be tested for whether the station needs to be
moved to an AP_VLAN interface.
To ease addition of tagged VLAN support, a member notempty is added to
struct vlan_description. Is is set to 1 if an untagged or tagged VLAN
assignment is requested and needs to be validated. The inverted form
allows os_zalloc() to initialize an empty description.
Though not depended on by the code, vlan_id assignment ensures:
* vlan_id = 0 will continue to mean no AP_VLAN interface
* vlan_id < 4096 will continue to mean vlan_id = untagged vlan id
with no per_sta_vif and no extra tagged vlan.
* vlan_id > 4096 will be used for per_sta_vif and/or tagged vlans.
This way struct wpa_group and drivers API do not need to be changed in
order to implement tagged VLANs or per_sta_vif support.
DYNAMIC_VLAN_* will refer to (struct vlan_description).notempty only,
thus grouping of the stations for per_sta_vif can be used with
DYNAMIC_VLAN_DISABLED, but not with CONFIG_NO_VLAN, as struct
hostapd_vlan is still used to manage AP_VLAN interfaces.
MAX_VLAN_ID will be checked in hostapd_vlan_valid and during setup of
VLAN interfaces and refer to IEEE 802.1q VID. VLAN_ID_WILDCARD will
continue to refer to int vlan_id.
Renaming vlan_id to vlan_desc when type changed from int to struct
vlan_description was avoided when vlan_id was also used in a way that
did not depend on its type (for example, when passed to another
function).
Output of "VLAN ID %d" continues to refer to int vlan_id, while "VLAN
%d" will refer to untagged IEEE 802.1q VID.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Commit 8bcf8de827 ('OpenSSL: Fix memory
leak in PKCS12 additional certificate parsing') tried to fix a memory
leak in both the 1.0.2(and newer) and 1.0.1 branches of PKCS12 parsing.
However, the 1.0.1 case was not properly tested and freeing of the
certificate after a successful SSL_CTX_add_extra_chain_cert() call
resulted in use of freed memory when going through the TLS handshake.
Fix this by not freeing the certificate in that specific case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Ciuple of the nonce comparisons used a strange '!os_memcmp() == 0' to
check if the values were different. While this resulted in correct
behavior, the construction is not exactly clear and clang has started
warning about this (-Wlogical-not-parentheses). Clean this up by using
'os_mecmp() != 0'.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The additional PKCS12 certificates were not freed properly in the loop
added in commit de2a7b796d ('OpenSSL: Use
connection certificate chain with PKCS#12 extra certs').
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 5c9a33702f ('OpenSSL: Clean up
crypto_hash_*() to use a single implementation') added a wrapper
function to allow the new OpenSSL API to be used with older OpenSSL
versions. However, the HMAC_CTX_free() wrapper was incorrectly skipping
the call to HMAC_CTX_cleanup() which is still needed to free the
resources OpenSSL allocated internally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
SSL_library_init() does not work properly after EVP_cleanup() starting
from OpenSSL 1.1.0 pre release 3. The automated library init/deinit
functions in that pre release are supposed to handle all initialization
and deinitialiation, so comment out the explicit calls to these function
with OpenSSL 1.1.0 and newer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 1eb87ae48d ('OpenSSL: Use
EVP_CIPHER_CTX_new() to work with OpenSSL 1.1.0') started using
EVP_CIPHER_CTX_new() to allocate EVP_CIPHER_CTX from heap instead of
using stack memory. This commit used incorrect EVP_CIPHER_CTX_reset()
function in number of cases when the allocated memory was supposed to be
freed instead of just reset for reuse. Fix this by using
EVP_CIPHER_CTX_free() properly.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
rfkill_init() uses realpath() which allocates memory and that memory was
not freed on the success path.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If SSL_CTX_new(SSLv23_method()) fails, tls_init() error path did not
free the allocated struct tls_data instance.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.
Add a new "pbss" argument to network block. The argument is used
in the following scenarios:
1. When network has mode=2 (AP), when pbss flag is set will start
as a PCP instead of an AP.
2. When network has mode=0 (station), when pbss flag is set will
connect to PCP instead of AP.
The function wpa_scan_res_match() was modified to match BSS according to
the pbss flag in the network block (wpa_ssid structure). When pbss flag
is set it will match only PCPs, and when it is clear it will match only
APs.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.
Add a pbss flag to the relevant structures to support starting a PCP and
connecting to a PCP. Implement support in the nl80211 driver by using
the new PBSS flag attribute.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
NOTE: kqueue has to be closed and re-build after forking. epoll *should*
do the same, but it seems that wpa_supplicant doesn't need it at least.
I have re-worked a little bit of the epoll code (moved into a similar
kqueue function) so it's trivial to requeue epoll if needed in the
future.
Signed-off-by: Roy Marples <roy@marples.name>
This function can be used to re-build eloop socket tables after forking
for eloop implementations that need this.
Signed-off-by: Roy Marples <roy@marples.name>
When a mesh point reconnects by starting from Authentication frame
sequence, the plink count was not decremented from its last connection.
This resulted in leaking peer link count and causing wpa_supplicant to
reject the connection after max_peer_links (default: 99) reconnects.
This was reproduced by pre-configuring 2 mesh points with mesh
credentials. Boot both mesh points and make sure they connect to each
other. Then in a loop reboot one of the mesh points after it
successfully connects while leaving the other mesh point up and running.
After 99 iterations the supplicant on mesh point that is not rebooting
will reject the connection request from the other mesh point.
Fix this by decrementing num_plinks when freeing a STA entry that is
still in PLINK_ESTAB state.
Signed-off-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Setting a long off channel wait time for P2P Action frames when
we know we are already on the right channel may cause a delay in
sending the Action frame (because the driver may not be able to
satisfy the request for long wait time until previous off channel
requests are over). This may be crucial for P2P response frames
that must be sent within 100 milliseconds of receiving the request.
Fix this by adjusting P2P Action frame wait times as follows:
1. For GO Negotiation Response frame, shorten the wait time to 100 ms.
This is reasonable because the peer has just sent us the GO
Negotiation Request frame, so it is known to be on the right
channel and is probably ready to send us the GO Negotiation
Confirmation frame without delay.
2. For GO Negotiation Confirmation, P2P Invitation Response, and
Provision Discovery Response frames, there is no need for wait
time at all as this is the last frame in the exchange. So set
the wait time to 50 ms to ensure there is enough time to send the
frame.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
There is no need to maintain three copies of this functionality even if
it is currently implemented as a single function call.
Signed-off-by: Jouni Malinen <j@w1.fi>
Rework the Acct-Session-Id and Acct-Multi-Session-Id implementation to
give better global and temporal uniqueness. Previously, only 32-bits of
the Acct-Session-Id would contain random data, the other 32-bits would
be incremented. Previously, the Acct-Multi-Session-Id would not use
random data. Switch from two u32 variables to a single u64 for the
Acct-Session-Id and Acct-Multi-Session-Id. Do not increment, this serves
no legitimate purpose. Exclusively use os_get_random() to get quality
random numbers, do not use or mix in the time. Inherently take a
dependency on /dev/urandom working properly therefore. Remove the global
Acct-Session-Id and Acct-Multi-Session-Id values that serve no
legitimate purpose.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
These can get allocated within eapol_auth_alloc(), so it is more logical
to free them in eapol_auth_free() instead of ieee802_1x_free_station()
that ends up calling eapol_auth_free().
Signed-off-by: Jouni Malinen <j@w1.fi>
Need to include these headers in C++ files for adding a binder interface
to wpa_supplicant. So, fix the following C++ compiler errors in them:
1. Add explicit C-style casts in wpa_buf.h header.
2. Move the nested definition of wpa_driver_scan_ssid in driver.h
outside of wpa_driver_scan_params because it is used in another
structure below.
Signed-off-by: Roshan Pius <rpius@google.com>
Event-Timestamp should be sent for all Accounting-Request packets and
only after the system clock has a sane value, not where there's a value
close to the Unix time epoch.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Calculate the required length needed for the extra ANQP elements added
to GAS response buffer instead of using fixed size and truncating the
response if there was not sufficient space.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Fix a possible null pointer dereference in tls_parse_pkcs12() when
loading a PKCS#12 file for the server keys and the file includes extra
certificates.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Need to clear the pac pointer for the first error case to avoid freeing
the previous PAC entry if the following entry has an invalid header.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Acct-Authentic is used to indicate how the user was authenticated and as
such, should not be sent in Accounting-On and Accounting-Off.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Per RFC 2866, 5.10, it is invalid to send Acct-Terminate-Cause in
Accounting-On and Accounting-Off (this is included only when
Acct-Status-Type is set to Stop).
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Ensure that if it is not possible to configure an allowed 20 MHz
channel pair, hostapd falls back to a single 20 MHz channel.
Signed-off-by: Eduardo Abinader <eabinader@ocedo.com>
If an interface is removed, zero the remembered ifindex.
Don't try to set properties on the interface when it is removed.
Signed-off-by: Roy Marples <roy@marples.name>
In the Android-specific case, make ca_cert directive parse a
space-separated list of hex-encoded CA certificate aliases following the
"keystores://" prefix. Server certificate validation should succeed as
long as the chain ends with one of them.
Signed-off-by: Rubin Xu <rubinxu@google.com>
Use the interface index from the correct structure according to the
message instead of assuming rtm_index is correct.
Signed-off-by: Roy Marples <roy@marples.name>
Couple of the image info fields were not printed previously in debug
log. Add those to make this more complete.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to debug AP selection issues in case of a invalid
RSN element or use of customer cipher suites that are not supported by
wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Number of deployed 80 MHz capable VHT stations that do not support 80+80
and 160 MHz bandwidths seem to misbehave when trying to connect to an AP
that advertises 80+80 or 160 MHz channel bandwidth in the VHT Operation
element. To avoid such issues with deployed devices, modify the design
based on newly proposed IEEE 802.11 standard changes.
This allows poorly implemented VHT 80 MHz stations to connect with the
AP in 80 MHz mode. 80+80 and 160 MHz capable stations need to support
the new workaround mechanism to allow full bandwidth to be used.
However, there are more or less no impacted station with 80+80/160
capability deployed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The called function nl80211_ht_vht_overrides() was not freeing "msg"
resource in error cases.
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
The PMKSA caching and RSN pre-authentication components were marked as
conditional on IEEE8021X_EAPOL. However, the empty wrappers are needed
also in a case IEEE8021X_EAPOL is defined with CONFIG_NO_WPA.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to follow a debug log from a hostapd process that
manages multiple interfaces.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The ap_sta_deauth_cb and ap_sta_disassoc_cb eloop timeouts are used to
clear a disconnecting STA from the kernel driver if the STA did not ACK
the Deauthentication/Disassociation frame from the AP within two
seconds. However, it was possible for a STA to not ACK such a frame,
e.g., when the disconnection happened due to hostapd pruning old
associations from other BSSes and the STA was not on the old channel
anymore. If that same STA then started a new authentication/association
with the BSS, the two second timeout could trigger during this new
association and result in the STA entry getting removed from the kernel.
Fix this by canceling these eloop timeouts when receiving an indication
of a new authentication or association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
clang started warning about the use of || with constants that came from
PCSC_FUNCS not being enabled in the build. It seems to be easier to just
ifdef this block out completely since that has the same outcome for
builds that do not include PC/SC support.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use compatibility wrapper functions to allow a single implementation
based on the latest OpenSSL API to be used to implement these functions
instead of having to maintain two conditional implementation based on
the library version.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use compatibility wrapper functions to allow a single implementation
based on the latest OpenSSL API to be used to implement these functions
instead of having to maintain two conditional implementation based on
the library version.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The changes needed for OpenSSL 1.1.0 had broken this since LibreSSL is
defining OPENSSL_VERSION_NUMBER in a manner that claims it to be newer
than the current OpenSSL version even though it does not support the
current OpenSSL API.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the final Phase 2 message needed fragmentation, EAP method decision
was cleared from UNCOND_SUCC or COND_SUCC to FAIL and that resulted in
the authentication failing when the EAP-Success message from the server
got rejected. Fix this by restoring the EAP method decision after
fragmentation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now the these functions cannot be made to fail by forcing the memory
allocation fail since the OpenSSL-internal version is used, add
TEST_FAIL check to allow OOM test cases to be converted to use the
TEST_FAIL mechanism without reducing coverage.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The EVP_CIPHER_CTX structure will be made opaque in OpenSSL 1.1.0, so
need to use EVP_CIPHER_CTX_new() with it instead of stack memory. The
design here moves the older OpenSSL versions to use that dynamic
allocation design as well to minimize maintenance effort.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The SSL_CIPHER **cipher argument was marked const in OpenSSL 1.1.0
pre-release 2 similarly to how this is in BoringSSL. Fix build with that
in preparation for supporting OpenSSL 1.1.0.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Free the allocated structure in error cases to remove need for each EAP
method to handle the error cases separately. Each registration function
can simply do "return eap_server_method_register(eap);" in the end of
the function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Free the allocated structure in error cases to remove need for each EAP
method to handle the error cases separately. Each registration function
can simply do "return eap_peer_method_register(eap);" in the end of the
function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Create global init to handle socket calls and route messages.
Register each interface inside the global driver so that
routing messages can find the interface based on rtm_ifindex.
Signed-off-by: Roy Marples <roy@marples.name>
We shouldn't use drv->ctx as it always points to the first BSS. When
using FullMAC driver with multi-BSS support it resulted in incorrect
treating nl80211 events. I noticed with with brcmfmac and BCM43602.
Before my change I was getting "disassociated" on a wrong interface:
wlan0-1: STA 78:d6:f0:00:11:22 IEEE 802.11: associated
wlan0-1: STA 78:d6:f0:00:11:22 WPA: pairwise key handshake completed (RSN)
wlan0: STA 78:d6:f0:00:11:22 IEEE 802.11: disassociated
With this patch it works as expected:
wlan0-1: STA 78:d6:f0:00:11:22 IEEE 802.11: associated
wlan0-1: STA 78:d6:f0:00:11:22 WPA: pairwise key handshake completed (RSN)
wlan0-1: STA 78:d6:f0:00:11:22 IEEE 802.11: disassociated
This doesn't apply to hostapd dealing with SoftMAC drivers when handling
AP SME & MLME is done it hostapd not the firmware.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
If wpa_supplicant was first configured with PKCS #12 -based client
certificate chain and then used with another network profile that used a
different certificate chain from a X.509 certificate PEM file instead of
PKCS#12, the extra certificate chain was not reconstructed properly with
older versions of OpenSSL that 1.0.2. This could result in the
authentication failing due to the client certificate chain not being
complete or including incorrect certificates.
Fix this by clearing the extra certificate chain when setting up a new
TLS connection with OpenSSL 1.0.1. This allows OpenSSL to build the
chain using the default mechanism in case the new TLS exchange does not
use PKCS#12.
The following hwsim test case sequence was able to find the issue:
ap_wpa2_eap_tls_pkcs12 ap_wpa2_eap_tls_intermediate_ca_ocsp
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
n_chans can have only values 1, 2, or 4 in this function, so the -1 case
could never be reached. Remove the unreachable case to get rid of static
analyzer warnings.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
chan is set to the result of pointer arithmetic (pointer to an entry in
an array) that can never be NULL. As such, there is no need to check for
it to be non-NULL before deference. Remove this check to avoid
complaints from static analyzers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Offloading of ACS to the driver changed the design a bit in a way that
iface->current_mode could actually be NULL when the offloaded ACS
mechanism supports band selection in addition to channel selection. This
resulted in a combination that is too complex for static analyzers to
notice. While acs_init() can be called with iface->current_mode == NULL
that is only in the case where WPA_DRIVER_FLAGS_ACS_OFFLOAD is in use.
In other words, the actual ACS functions like acs_cleanup() that would
dereference iface->current_mode are not used in such a case.
Get rid of static analyzer warnings by explicitly checking
iface->current_mode in acs_init() for the case where ACS offloading is
not used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to debug issues with old scan results being ignored
during P2P_FIND. A single rx_time would have been fine with
os_gettime(), but with os_get_reltime(), both rx_time and find_start
values are needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There was a race condition in how the l2_packet sockets got read that
could result in the same socket (e.g., non-bridge) to process both the
EAP-Success and the immediately following EAPOL-Key msg 1/4 instead of
each frame going in alternative order between the bridge and non-bridge
sockets. This could be hit, e.g., if the wpa_supplicant process did not
have enough CPU to process all the incoming frames without them getting
buffered and both sockets reporting frames simultaneously.
This resulted in the duplicated EAP-Success frame getting delivered
twice for processing and likely also the EAPOL-Key msg 1/4 getting
processed twice. While the latter does not do much harm, the former did
clear the EAP authentication state and could result in issues.
Fix this by extended the l2_packet Linux packet socket workaround for
bridge to check for duplicates against the last two received frames
instead of just the last one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the packet socket on the bridge interface to receive
own transmitted frames between the bridge and non-bridge sockets
receiving the same incoming frame from a foreign host. This resulted in
the hash checksum validation step failing to notice a duplicate RX due
to the own frame updating the store hash value.
The own frame did get dropping in RX EAPOL processing, but that was too
late to address the issue with duplicate RX. Fix this by dropping own
frames already in l2_packet layer before checking and updating the last
RX hash value.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function can fail at least in theory, so check its return value
before proceeding. This is mainly helping automated test case coverage
to reach some more error paths.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was reported to fail with Windows 2012r2 with "Invalid Compound_MAC
in cryptobinding TLV". It turns out that the server decided to go
through inner EAP method (EAP-MSCHAPv2 in the reported case) even when
using PEAP fast-reconnect. This seems to be against the [MS-PEAP]
specification which claims that inner EAP method is not used in such a
case. This resulted in a different CMK being derived by the server (used
the version that used ISK) and wpa_supplicant (used the version where
IPMK|CMK = TK without ISK when using fast-reconnect).
Fix this interop issue by making wpa_supplicant to use the
fast-reconnect version of CMK derivation only when using TLS session
resumption and the server having not initiated inner EAP method before
going through the cryptobinding exchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous behavior of bursting out all retry attempts of an SD Query
frame during a single search/listen iteration does not look very helpful
in the case where the peer does not ACK the query frame. Since the peer
was found in the search, but is not ACKing frames anymore, it is likely
that it left its listen state and we might as well do something more
useful to burst out a significant number of frames in hopes of seeing
the peer.
Modify the SD Query design during P2P Search to send out only a single
attempt (with likely multiple link-layer retries, if needed) per
search/listen iteration to each peer that has pending SD queries. Once
no more peers with pending queries remain, force another Listen and
Search phase to go through before continuing with the pending SD
queries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If P2P support is included in wpa_supplicant build (CONFIG_P2P=y), but
P2P functionality is explicitly disabled (e.g., "P2P_SET disabled 1"),
couple of AP management frame processing steps did not check against
hapd->p2p_group being NULL and could end up dereferencing a NULL pointer
if a Probe Request frame or (Re)Association Request frame was received
with a P2P IE in it. Fix this by skipping these steps if hapd->p2p_group
is NULL.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit e6dd8196e5 ('Work around Linux
packet socket regression') forgot to add the l2_packet_init_bridge()
wrapper for l2_packet_pcap.c while updating all the other l2_packet
options. This resulted in wpa_supplicant build failing due to missing
l2_packet_init_bridge() function when using CONFIG_L2_PACKET=pcap in
wpa_supplicant/.config. Fix this by adding the wrapper function.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new wps_force_{auth,encr}_types parameters can be used in test build
(CONFIG_WPS_TESTING) to force wpa_supplicant to use the specified value
in the Authentication/Encryption Type flags attribute. This can be used
to test AP behavior on various error cases for which there are
workarounds to cover deployed device behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some deployed implementations seem to advertise incorrect information in
this attribute. A value of 0x1b (WPA2 + WPA + WPAPSK + OPEN, but no
WPA2PSK) has been reported to be used. Add WPA2PSK to the list to avoid
issues with building Credentials that do not use the strongest actually
supported authentication option (that device does support WPA2PSK even
when it does not claim it here).
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the Registrar code to generate a Credential with
auth type WPAPSK (i.e., WPA v1) with encr type AES if the Enrollee
claimed support for WPAPSK and not WPA2PSK while the AP was configured
in mixed mode WPAPSK+WPA2PSK regardless of how wpa_pairwise (vs.
rsn_pairwise) was set since encr type was selected from the union of
wpa_pairwise and rsn_pairwise. This could result in the Enrollee
receiving a Credential that it could then not use with the AP.
Fix this by masking the encryption types separately on AP based on the
wpa_pairwise/rsn_pairwise configuration. In the example case described
above, the Credential would get auth=WPAPSK encr=TKIP instead of
auth=WPAPSK encr=AES.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it somewhat easier for the station to be able to receive and
process the encrypted WNM-Notification frames that the AP previously
sentt immediately after receiving EAPOL-Key msg 4/4. While the station
is supposed to have the TK configured for receive before sending out
EAPOL-Key msg 4/4, not many actual implementations do that. As such,
there is a race condition in being able to configure the key at the
station and the AP sending out the first encrypted frame after EAPOL-Key
4/4. The extra 100 ms time here makes it more likely for the station to
have managed to configure the key in time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add SSL_SESSION_get_master_key() compatibility wrapper for older OpenSSL
versions to be able to use the new openssl_tls_prf() implementation for
OpenSSL 1.1.0 with all supported versions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
SSL_get_client_random() and SSL_get_server_random() will be added in
OpenSSL 1.1.0. Provide compatibility wrappers for older versions to
simplify the tls_connection_get_random() implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The OpenSSL project will not support version 1.0.0 anymore. As there
won't be even security fixes for this branch, it is not really safe to
continue using 1.0.0 and we might as well drop support for it to allow
cleaning up the conditional source code blocks.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The OpenSSL project will not support version 0.9.8 anymore. As there
won't be even security fixes for this branch, it is not really safe to
continue using 0.9.8 and we might as well drop support for it to allow
cleaning up the conditional source code blocks.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the p2p->pending_listen_freq to be left indicating
that there is a pending ROC for a listen operation if a P2P_FIND command
was timed to arrive suitably between a previous Listen operation issuing
a ROC request and the kernel code starting that request. This could
result in the P2P state machine getting stuck unable to continue the
find ("P2P: p2p_listen command pending already").
Fix this by clearing p2p->pending_listen_freq when starting P2P_FIND
command execution.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new optional group_ssid=<hexdump> argument in the P2PS-PROV-DONE
event can be used to help in identifying the exact group if there have
been multiple groups with the same P2P Interface Address in short period
of time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When we receive FST Setup Request when session already exists, the
following validations take place:
1. we drop the frame if needed according to MAC comparison
2. we drop the frame if the session is "not pending", i.e., if FST
Setup Response was already exchanged (sent or received).
There are two issues with the above:
1. MAC comparison is relevant only before the Setup Response exchange.
In other words, Setup Request should not be dropped due to MAC
comparison after Setup Response has been exchanged.
2. Receiving Setup Request after Setup Response exchange most likely
means that FST state machine is out of sync with the peer. Dropping
the Setup Request will not help solve this situation.
The fix is:
1. do MAC comparison only if session is "pending", i.e., Setup Response
was not yet exchanged.
2. In case Setup Response was already exchanged, reset our session and
handle the Setup Request as if it arrived when session doesn't exist.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Explicitly check for the failure event to include a certificate before
trying to build the event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While this could in theory be claimed to be ready for something to be
added to read a field following the server_write_IV, it does not look
likely that such a use case would show up. As such, just remove the
unused incrementing of pos at the end of the function to get rid of a
useless static analyzer complaint.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes some static analyzers complain about stored value never being
read. While it is good to clear some other temporary variables, this
local variable i has no security private information (it has a fixed
value of 20 here) and trying to clear it to 0 does not add any value.
Remove that part of the "wipe variables" to avoid one useless static
analyzer complaint.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
As a dedicated P2P Device interface does not have a network
interface associated with it, trying to call linux_iface_up()
on it would always fail so this call can be skipped for
such an interface.
Getting interface nlmode can be done only after bss->wdev_id is
set, so move this call to wpa_driver_nl80211_finish_drv_init(),
and do it only in case the nlmode != NL80211_IFTYPE_P2P_DEVICE.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
IEEE Std 802.11-2012 11.3.5.4 specifies the PMKID for SAE-derived keys
as:
L((commit-scalar + peer-commit-scalar) mod r, 0, 128)
This is already calculated in the SAE code when the PMK is derived, but
not saved anywhere. Later, when generating the PMKID for plink action
frames, the definition for PMKID from 11.6.1.3 is incorrectly used.
Correct this by saving the PMKID when the key is generated and use it
subsequently.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Since hostapd supports ACS now, let's enable its support in
wpa_supplicant as well when starting AP mode.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
[u.oelmann@pengutronix.de: adjusted added text in defconfig]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Let's reuse hostapd code for such handling. This will be useful to get
ACS support into wpa_supplicant where this one needs to handle the
survey event so it fills in the result ACS subsystem will require.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
The data->state == WAIT_FRAG_ACK case is already handling all cases
where data->out_buf could be non-NULL, so this additional check after
the WAIT_FRAG_ACK steps cannot be reached. Remove the duplicated dead
code.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, a fixed 1300 fragment_size was hardcoded. Now the EAP
profile parameter fragment_size can be used to override this.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows RADIUS failover to be performed if send() return EACCES
error which is what happens after a recent Linux kernel commit
0315e382704817b279e5693dca8ab9d89aa20b3f ('net: Fix behaviour of
unreachable, blackhole and prohibit') for a local sender when route type
is prohibit.
This fixes the hwsim test case radius_failover when running against a
kernel build that includes that commit.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 986de33d5c ('Convert remaining SSID
routines from char* to u8*') started using wpa_ssid_txt() to print out
the SSID for the Called-Station-Id attribute in RADIUS messages. This
was further modified by commit 6bc1f95613
('Use printf escaping in SSID-to-printable-string conversion') to use
printf escaping (though, even without this, wpa_ssid_txt() would have
masked characters).
This is not desired for Called-Station-Id attribute. While it is defined
as a "String", RFC 2865 indicates that "a robust implementation SHOULD
support the field as undistinguished octets.".
Copy the SSID as an array of arbitrary octets into Called-Station-Id to
avoid any kind of masking or escaping behavior. This goes a step further
from the initial implementation by allowing even the possible (but
unlikely in practical use cases) 0x00 octet in the middle of an SSID.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends multi-OCSP support to verify status for intermediate CAs in
the server certificate chain.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
ocsp=3 extends ocsp=2 by require all not-trusted certificates in the
server certificate chain to receive a good OCSP status. This requires
support for ocsp_multi (RFC 6961). This commit is only adding the
configuration value, but all the currently included TLS library wrappers
are rejecting this as unsupported for now.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
