This was forgotten when the key_mgmt parser for SAE and FT-SAE was
added.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
The new openssl_cipher configuration parameter can be used to select
which TLS cipher suites are enabled for TLS-based EAP methods when
OpenSSL is used as the TLS library. This parameter can be used both as a
global parameter to set the default for all network blocks and as a
network block parameter to override the default for each network
profile.
Signed-off-by: Jouni Malinen <j@w1.fi>
mac_addr=2 and preassoc_mac_addr=2 parameters can now be used to
configure random MAC address to be generated by maintaining the OUI part
of the permanent MAC address (but with locally administered bit set to
1). Other than that, these values result in similar behavior with
mac_addr=1 and preassoc_mac_addr=1, respectively.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds experimental support for wpa_supplicant to assign random local
MAC addresses for both pre-association cases (scan, GAS/ANQP) and for
connections. MAC address policy for each part can be controlled
separately and the connection part can be set per network block.
This requires support from the driver to allow local MAC address to be
changed if random address policy is enabled. It should also be noted
that number of drivers would not support concurrent operations (e.g.,
P2P and station association) with random addresses in use for one or
both.
This functionality can be controlled with the global configuration
parameters mac_addr and preassoc_mac_addr which set the default MAC
address policies for connections and pre-association operations (scan
and GAS/ANQP while not connected). The global rand_addr_lifetime
parameter can be used to set the lifetime of a random MAC address in
seconds (default: 60 seconds). This is used to avoid unnecessarily
frequent MAC address changes since those are likely to result in driver
clearing most of its state. It should be noted that the random MAC
address does not expire during an ESS connection, i.e., this lifetime is
only for the case where the device is disconnected.
The mac_addr parameter can also be set in the network blocks to define
different behavior per network. For example, the global mac_addr=1 and
preassoc_mac_addr=1 settings and mac_addr=0 in a home network profile
would result in behavior where all scanning is performed using a random
MAC address while connections to new networks (e.g.,
Interworking/Hotspot 2.0) would use random address and connections to
the home network would use the permanent MAC address.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to configure a Hotspot 2.0 Release 2 network externally
for a case where wpa_supplicant-based Interworking network selection is
not used and the update_identifier cannot be copied directly from a
cred.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Use an explicit memset call to clear any wpa_supplicant configuration
parameter that contains private information like keys or identity. This
brings in an additional layer of protection by reducing the length of
time this type of private data is kept in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is not really necessary check, but it keeps a static analyzer
happier by avoiding dead increment. Doing it this way rather than
removing the increment is less likely to cause problems when new entries
are added here in the future (the "dead" increment would be very much
needed in those cases).
Signed-off-by: Jouni Malinen <j@w1.fi>
The pointer to the current position is enough to figure out whether the
proto string is the first one in the buffer. Removing the separate
tracking variable cleans up a static analyzer warning on dead
assignment.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, eight character random passphrase was generated
automatically for P2P GO. The new p2p_passphrase_len parameter can be
used to increase this length to generate a stronger passphrase for cases
where practicality of manual configuration of legacy devices is not a
concern.
Signed-off-by: Jouni Malinen <j@w1.fi>
Performing a P2P Device flow such as p2p_listen or
p2p_find, can degrade the performance of an active interface
connection, if the listen frequency is different than the
frequency used by that interface.
To reduce the effect of P2P Device flows on other interfaces,
try changing the listen channel of the P2P Device to match the
operating channel of one of the other active interfaces. This change
will be possible only in case that the listen channel is not forced
externally, and will be delayed to a point where the P2P Device
state machine is idle.
The optimization can be configured in the configuration file and
is disabled by default.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This makes the p2p_find default delay value configurable as
p2p_search_delay parameter through the configuration file (and through
control interface "SET p2p_search_delay <value>" on the P2P management
interface.
This parameter controls the number milliseconds of extra delay that is
added between search iterations when there is a concurrent operation in
progress. This can be used, e.g., p2p_search_delay=100 to make p2p_find
friendlier to concurrent operations by avoiding it from taking 100% of
the radio resources. The default value is the previous default, i.e.,
500 ms. Smaller values can be used to find peers more quickly at the
cost of larger effect to concurrent operations while a larger value
leaves more time for the concurrent operations at the cost of making
device discovery take longer time.
The optional p2p_find delay argument can still be used to override the
search delay for each search operation.
Since the P2P_CONCURRENT_SEARCH_DELAY macro is not used anymore, the
driver specific build parameter for bcmdhd from Android.mk is also
removed. Similar configuration can now be achieved with
p2p_search_delay=0 in the p2p0 interface configuration file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new wowlan_triggers option to wpa_supplicant.conf. The triggers in
this key will be used to configure the kernel wowlan configuration.
For now, support only simple flags. More complex triggers can be added
later on.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
This allows the specific SIM to be identified for authentication
purposes in multi-SIM devices. This SIM number represents the index of
the SIM slot. This SIM number shall be used for the authentication using
the respective SIM for the Wi-Fi connection to the corresponding
network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
"GET_CRED <id> <field>" can now be used to fetch credential parameters
over the control interface. This does not allow passwords etc. private
material to be retrieved ("*" is returned for those if the value is set
regardless of the value). FAIL is returned if the requested parameter
has not been set. For cred parameters that can have multiple values,
newline separated list of values is returned.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new parameter can be used to configure credentials to mandate use
of OCSP stapling for AAA server authentication.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This new priority parameter can be used to specify priorities between
credentials provisioned by the same SP. cred->priority is checked first
and if it is same and the provisioning_sp parameter matches, the new
sp_priority is used to order the credentials. It should be noted that
the order of priorities is different (higher 'priority' value indicates
higher priority of the credential, while higher 'sp_priority' indicates
lower priority of the credential).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new credential parameter req_conn_capab can be used to specify
restrictions on roaming networks providing connectivity for a set of
protocols/ports.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new credential parameter max_bss_load can be used to specify
restrictions on BSS Load in the home network.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new credential parameters min_{dl,ul}_bandwidth_{home,roaming} can
be used to specify restrictions on available backhaul bandwidth.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new provisioning_sp cred field can now be used to track which SP
provisioned the credential. This makes it easier to find the matching
PPS MO from the management tree (./Wi-Fi/<provisioning_sp>).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_cli fetch_osu command can be used to fetch information about
all OSU providers and write that to a text file with the icons in
separate files. cancel_osu_fetch command can be used to stop ongoing OSU
provider list fetch.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The HS 2.0 Indication element from wpa_supplicant now includes the
release number field and wpa_supplicant shows the release number of the
AP in STATUS command (hs20=1 replaced with hs20=<release>).
The new update_identifier field in the cred block can now be used to
configure the PPS MO ID so that wpa_supplicant adds it to the Indication
element in Association Request frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new roaming_partner parameter within a cred block can be used to
configure priorities for roaming partners.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
1. In wpa_config_process_bgscan() fix memory leak after
calling wpa_config_parse_string()
2. In hostapd_config_defaults(), on failure to allocate bss->radius,
conf->bss was not freed.
3. In p2p_deauth_nofif(), memory allocated in p2p_parse_ies() was not
freed in case of NULL minor_reason_code.
4. In p2p_disassoc_nofif(), memory allocated in p2p_parse_ies() was
not freed in case of NULL minor_reason_code.
5. In p2p_process_go_neg_conf(), memory allocated was not freed in
case that the P2P Device interface was not waiting for a
GO Negotiation Confirm.
6. In wpa_set_pkcs11_engine_and_module_path(), the wrong pointer was
checked.
Signed-hostap: Eytan Lifshitz <eytan.lifshitz@intel.com>
This new mechanism allows P2P Client to request an IPv4 address from the
GO as part of the 4-way handshake to avoid use of DHCP exchange after
4-way handshake. If the new mechanism is used, the assigned IP address
is shown in the P2P-GROUP-STARTED event on the client side with
following new parameters: ip_addr, ip_mask, go_ip_addr. The assigned IP
address is included in the AP-STA-CONNECTED event on the GO side as a
new ip_addr parameter. The IP address is valid for the duration of the
association.
The IP address pool for this new mechanism is configured as global
wpa_supplicant configuration file parameters ip_addr_go, ip_addr_mask,
ip_addr_star, ip_addr_end. For example:
ip_addr_go=192.168.42.1
ip_addr_mask=255.255.255.0
ip_addr_start=192.168.42.2
ip_addr_end=192.168.42.100
DHCP mechanism is expected to be enabled at the same time to support P2P
Devices that do not use the new mechanism. The easiest way of managing
the IP addresses is by splitting the IP address range into two parts and
assign a separate range for wpa_supplicant and DHCP server.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
All te network blocks and credentials were already cleared, but
configurations blobs should also be cleared here, e.g., to get
more consistent behavior test cases using EAP-FAST PACs.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new cred block parameter 'temporary' can be used to indicate that a
cred block is not to be saved to wpa_supplicant configuration file
(e.g., "SET_CRED 0 temporary 1"). This is similar to the concept of
temporary network blocks and allows cred blocks to be managed outside
the wpa_supplicant config file when other parameters are still saved to
the file written by wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
There are use cases requesting the host driver to initiate the TDLS
setup with the peer only when configured by the external applications.
Thus, enable this control by tdls_external_control=1 and pass the
requisite information for the specific TDLS operation to the driver
on the request from such use cases.
This operation mode expects the driver to initiate TDLS link
automatically based on signal strength and traffic to a peer and tear
down links whenever they are not used or suitable due to signal strength
etc. The list of peers with which such operations are to be performed
are provided with the TDLS driver operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is a better way of matching P2P groups based on the unique P2P
Device Address (e.g., from P2P Group ID) and SSID pair instead of using
the not necessarily unique P2P Interface Address.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This option can be used to globally configure bgscan parameters
for all the network blocks.
Note that this configuration will not override a network block
specific bgscan settings, but will only be used in case that
the network block does not have a valid bgscan configuration.
Signed-hostap: Haim Dreyfuss <haim.dreyfuss@intel.com>
Add the option to ask for VHT operation similarly to the way ht40 is
configured - either by adding 'vht' param to the relevant p2p_*
commands or by configuring p2p_go_vht=1 in the configuration file.
This patch only adds the configuration option (e.g., via control
interface). The actual handling of the VHT parameter (asking the driver
to use VHT, etc.) will be done by the following patch.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
The new p2p_add_cli_chan=1 configuration parameter can be used to
request passive-scan channels to be included in P2P channel lists for
cases where the local end may become the P2P client in a group. This
allows more options for the peer to use channels, e.g., if the local
device is not aware of its current location and has marked most channels
to require passive scanning.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new p2p_no_go_freq frequency range list (comma-separated list of
min-max frequency ranges in MHz) can now be used to configure channels
on which the local device is not allowed to operate as a GO, but on
which that device can be a P2P Client. These channels are left in the
P2P Channel List in GO Negotiation to allow the peer device to select
one of the channels for the cases where the peer becomes the GO. The
local end will remove these channels from consideration if it becomes
the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new configuration parameter external_sim=<0/1> can now be used to
configure wpa_supplicant to use external SIM/USIM processing (e.g., GSM
authentication for EAP-SIM or UMTS authentication for EAP-AKA). The
requests and responses for such operations are sent over the ctrl_iface
CTRL-REQ-SIM and CTRL-RSP-SIM commands similarly to the existing
password query mechanism.
Changes to the EAP methods to use this new mechanism will be added in
separate commits.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows credentials to be limited from being used to connect to a
network unless the AP advertises a matching roaming consortium OI.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allow domain_suffix_match to be specified for a cred block and then
get this copied for the network blocks generated from this credential as
part of Interworking network selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Credentials can now be configured with more than one FQDN ('domain'
field in the cred block) to perform Domain Name List matching against
multiple home domains.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new domain_suffix_match (and domain_suffix_match2 for Phase 2
EAP-TLS) can now be used to specify an additional constraint for the
server certificate domain name. If set, one of the dNSName values (or if
no dNSName is present, one of the commonName values) in the certificate
must have a suffix match with the specified value. Suffix match is done
based on full domain name labels, i.e., "example.com" matches
"test.example.com" but not "test-example.com".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_config_write_key_mgmt has a buffer size of 50. This is not enough
to fit the longest case. I used a network with "WPA-PSK WPA-EAP
WPA-NONE" and CONFIG_IEEE80211R=y + CONFIG_IEEE80211W=y to produce
a string longer than 50 chars. Increase the buffer size to 100 to
prevent truncated output.
Truncated output is not the only problem. If the buffer end is
reached when adding certain key mgmt types the function does not
return immediately. This leaves pos > end. When a second os_sprintf
is called the calculation of end - pos yields a large positive
number for buffer size. End result is a write beyond the buffer end.
Fix this by bailing out if buffer end is reached.
Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
no_ctrl_interface parsing was declared within ifdef CONFIG_CTRL_IFACE
block, so the parser function needs to be marked similarly.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to override previously set ctrl_interface value in a
way that clears the variable to NULL instead of empty string. The only
real use case for this is to disable per-interface ctrl_interface from
the additional control file (-I<file>) in case ctrl_interface was set in
the main configuration file. It should be noted that zero-length
ctrl_interface parameter can be used to initiate some control interface
backends, so simpler designs were not available for this.
The format of the new parameter is not exactly cleanest due to
configuration file parsing assumptions. For example:
ctrl_interface=....
no_ctrl_interface=
would end up with ctrl_interface=NULL.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There was already a CFG_CHANGED_P2P_OPER_CHANNEL handler function, but
this flag was not set when the p2p_oper_reg_class or p2p_oper_channel
parameters were changed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Record all generated per-client PSKs in the persistent group network
block and configure these for the GO Authenticator whenever re-starting
the persistent group. This completes per-client PSK support for
persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
When using OpenSSL with TLS-based EAP methods, wpa_supplicant can now be
configured to use OCSP stapling (TLS certificate status request) with
ocsp=1 network block parameter. ocsp=2 can be used to require valid OCSP
response before connection is allowed to continue.
hostapd as EAP server can be configured to return cached OCSP response
using the new ocsp_stapling_response parameter and an external mechanism
for updating the response data (e.g., "openssl ocsp ..." command).
This allows wpa_supplicant to verify that the server certificate has not
been revoked as part of the EAP-TLS/PEAP/TTLS/FAST handshake before
actual data connection has been established (i.e., when a CRL could not
be fetched even if a distribution point were specified).
Signed-hostap: Jouni Malinen <j@w1.fi>
If a VIF is already associated, then only scan on the associated
frequency if user requests such. This is a big help when using
lots of virtual stations.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
The new sched_scan_interval parameter can be used to set the default
sched_scan interval, e.g., for power saving purposes.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows one to limit the channels that wpa_supplicant will
scan. This is a useful addition to the freq_list configurable
in the network {} section.
Signed-hostap: Ben Greear <greearb@candelatech.com>
There are quite a few places in the current implementation where a nul
terminated string is generated from binary data. Add a helper function
to simplify the code a bit.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to configure wpa_supplicant to ignore old scan results
from the driver cache in cases where such results were not updated after
the scan trigger from wpa_supplicant. This can be useful in some cases
where the driver may cache information for a significant time and the AP
configuration is changing. Many such cases are for testing scripts, but
this could potentially be useful for some WPS use cases, too.
Signed-hostap: Jouni Malinen <j@w1.fi>
This new parameter allows wpa_supplicant AP mode operations to use
similar design to the vendor_elements parameter in hostapd to add
vendor_elements into Beacon/Probe Response IE parameters.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_ignore_shared_freq=1 in the configuration file (or "SET
p2p_ignore_shared_freq 1" on control interface) can now be used to
configure wpa_supplicant to ignore the preference on shared operating
channel when the driver support multi-channel concurrency. The default
behavior is to try to start any new P2P group on an operating channel
that is already in use on another virtual interface to avoid extra cost
from hopping between multiple channels. If this new parameter is set to
1, such preference is not used and instead, the channel for the new P2P
group is selected based on other preferences while ignoring operating
channels of any concurrent connection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for VHT capability overrides to allow testing connections
with a subset of the VHT capabilities that are actually supported by
the device. The only thing that isn't currently supported (by mac80211
and this code) is the RX/TX highest rate field.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Instead of using atoi(), use strtol() which allows checking if
the configuration values are valid integers and can understand
more than just decimal (also hexadecimal and octal). This not
only allows specifying some fields in hex (which can be useful)
but also rejecting invalid configurations, e.g.,
disassoc_low_ack=27 * 2
which was previously read as just 27.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
beacon_int (in TU) can now be used to configure Beacon interval for AP
mode operations (including P2P GO) in wpa_supplicant. This can be set
either in a network block or as a global parameter in the configuration
file (or with "SET beacon_int <value>" control interface command) to
apply for all networks that do not include the beacon_int parameter to
override the default.
In addition, this commits extends the dtim_period parameter to be
available as a global parameter to set the default value. dtim_period is
now stored in the configuration file, too, if it was set.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"WPS_NFC_TOKEN <WPS/NDEF>" used to generate a new NFC password token
regardless of whether there was a pre-configured token in the
configuration. Change this to use the pre-configured value, if
available, instead. This allows the same command to be used to write the
password token to an NFC tag more conveniently.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd.conf sae_groups parameter can now be used to limit the set of
groups that the AP allows for SAE. Similarly, sae_groups parameter is
wpa_supplicant.conf can be used to set the preferred order of groups. By
default, all implemented groups are enabled.
Signed-hostap: Jouni Malinen <j@w1.fi>
Requires Linux kernel patch to make the SGI-20 properly disabled. SGI-40
will already work since Linux 3.4 or so.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Basic support for the 60 GHz band. Neither P2P nor WPS are yet taken
care off. Allows to start AP with very simple config:
network={
ssid="test"
mode=2
frequency=60480
key_mgmt=NONE
}
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new excluded_ssid parameter within a cred block can be used to
excluded networks from matching with credentials.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, PMF (protected management frames, IEEE 802.11w) could be
enabled only with a per-network parameter (ieee80211w). The new global
parameter (pmf) can now be used to change the default behavior to be PMF
enabled (pmf=1) or required (pmf=2) for network blocks that do not
override this with the ieee80211w parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, OKC (opportunistic key caching, a.k.a. proactive key
caching) could be enabled only with a per-network parameter
(proactive_key_caching). The new global parameter (okc) can now be used
to change the default behavior to be OKC enabled (okc=1) for network
blocks that do not override this with the proactive_key_caching
parameter.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new p2p_no_group_iface=1 configuration parameter can now be used to
disable the default behavior of adding a separate interface for the P2P
group when driver support for concurrent interfaces is available.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
By default, P2P is enabled globally for all virtual interfaces and this
makes wpa_supplicant include WSC and P2P IEs in Probe Request frames for
all scans even if this is for a non-P2P station connection to speed up
device discovery. If an interface is dedicated for non-P2P station mode
operations, it is now possible to disable addition of WSC and P2P IEs
into Probe Request frames with a per-interface p2p_disabled parameter.
This can be set either in the configuration file (p2p_disabled=1) or at
run time ("wpa_cli -i wlan0 set p2p_disabled 1"). Unlike the previous
mechanism ("wpa_cli p2p_set disabled 1"), the new parameter changes the
behavior only for the specified interface while other interfaces
continue to follow the global P2P enabled/disabled state.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When specified in the conf file this parameter will make all invocations
of p2p_group_add, p2p_connect, and p2p_invite behave as if "ht40" has
been specified on the command line. This shouldn't do harm since
regulatory constraints and driver capabilities are consulted anyway
before starting HT40 mode.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
This introduces new AKM for SAE and FT-SAE and adds the initial parts
for going through the SAE Authentication frame exchange. The actual SAE
algorithm and new fields in Authentication frames are not yet included
in this commit and will be added separately. This version is able to
complete a dummy authentication with the correct authentication
algorithm and transaction values to allow cfg80211/mac80211 drivers to
be tested (all the missing parts can be handled with
hostapd/wpa_supplicant changes).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows both hostapd and wpa_supplicant to be used to derive and
configure keys for GCMP. This is quite similar to CCMP key
configuration, but a different cipher suite and somewhat different rules
are used in cipher selection. It should be noted that GCMP is not
included in default parameters at least for now, so explicit
pairwise/group configuration is needed to enable it. This may change in
the future to allow GCMP to be selected automatically in cases where
CCMP could have been used.
This commit does not included changes to WPS or P2P to allow GCMP to be
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
auto_interworking=1 configuration parameter can be used to request
wpa_supplicant to use Interworking network selection automatically as a
part of the normal (non-Interworking) network selection if the scan
results do not match with enabled networks. This makes scanning work
similarly to the "interworking_select auto" command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This list can get truncated due to too many addresses getting added.
Reorder the entries in a way that allows the most recently added values
to be maintained in the list and use better debug/error messages when
parsing the value.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
There is no need to mandate admission control (ACM=1) by default, so
clear that flag in the case the configuration file does not specify
wmm_ac_{vo,vi}_acm value. This gets closer to the values mentioned
in the sample hostapd.conf file and reduces the need to specify WMM
parameters in the configuration file for most common use cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
In case of P2P GO and AP mode, wpa_supplicant uses the default hostapd
parameters for WMM. In the default parameters the ACM bit for video and
voice are set to 1, meaning, P2P devices and stations which are
connected to the GO cannot pass voice or video data packets. Allow this
to be changed through wpa_supplicant configuration file with wmm_ac_*
parameters.
Signed-hostap: Yoni Divinsky <yoni.divinsky@ti.com>
This enables setting a different max inactivity timeout for P2P GO.
This timeout is used to detect inactive clients. In some scenarios
it may be useful to have control over this and set a shorter timeout
than the default 300s. For example when running STA and P2P GO interfaces
concurrently, the STA interface may perform scans which may cause the
GO to miss a disassoc / deauth frames from a client and keep assuming
that the client is connected until the inactivity detection kicks in.
300 secs is a bit too long for such scenarios and creates a bad user
experience.
Signed-hostap: Eyal Shapira <eyal@wizery.com>
The new ssid2 parameter can be used as an alternative mechanism for
configuring SSID for hostapd. It uses the same formats that
wpa_supplicant uses in the configuration file for strings.
Signed-hostap: Jouni Malinen <j@w1.fi>
P"<escaped string>" can now be used as an alternative method for
specifying non-ASCII strings (including control characters). For
example, ssid=P"abc\x00test".
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the password parameter for EAP methods to be fetched
from an external storage.
Following example can be used for developer testing:
ext_password_backend=test:pw1=password|pw2=testing
network={
key_mgmt=WPA-EAP
eap=TTLS
identity="user"
password=ext:pw1
ca_cert="ca.pem"
phase2="auth=PAP"
}
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows wpa_supplicant configuration file to be created without
the PSK/passphrase value included in the file when a backend for
external password storage is available.
Following example can be used for developer testing:
ext_password_backend=test:psk1=12345678
network={
ssid="test-psk"
key_mgmt=WPA-PSK
psk=ext:psk1
}
Signed-hostap: Jouni Malinen <j@w1.fi>
This new mechanism can be used to make wpa_supplicant using external
storage (e.g., key store in the operating system) for passwords,
passphrases, and PSKs. This commit is only adding the framework part
needed to support this, i.e., no actual configuration parameter can
yet use this new mechanism. In addition, only a simple test backend
is added to allow developer testing of the functionality.
Signed-hostap: Jouni Malinen <j@w1.fi>
Each cred block can now be matched based on Roaming Consortium OI as an
alternative mechanism to using NAI Realm information. This may be
optimized for efficiency in the future since Roaming Consortium
information is available in scan results without having to go through
ANQP queries. In addition, this is easier to support in case there is a
large number of realms that can be used for authentication.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new cred block parameters eap, phase1, and phase2 can be used to
select which EAP method is used with network selection instead of using
the value specified in ANQP information (e.g., NAI Realm).
Signed-hostap: Jouni Malinen <j@w1.fi>
Allow the user to configure an RSSI threshold in dBm below which the
nl80211 driver won't report scan results. Currently only supported
during scheduled (PNO) scans.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of requiring low-level access to an NFC device and synchronous
operations, the new WPS_NFC_TOKEN and WPS_NFC ctrl_iface commands can be
used to build a NFC password token and initiate WPS protocol run using
that token (or pre-configured values) as separate commands. The
WPS_NFC_TOKEN output can be written to a NFC tag using an external
program, i.e., wpa_supplicant does not need to have low-level code for
NFC operations for this.
Signed-hostap: Jouni Malinen <j@w1.fi>
The nl80211 driver interface does not allow 128-bit WEP to be used
without a vendor specific cipher suite and no such suite is defined for
this purpose. Do not accept WEP key length 16 for nl80211 driver
interface forn ow. wext-interface can still try to use these for
backwards compatibility.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Do not try to associate with a network that has an invalid or incomplete
configuration because the association or at least data connection would
fail anyway. This commits adds a common function for checking whether a
network block is disabled to make it easier to check network blocks
without having to reject them during configuration file parsing (which
would prevent wpa_supplicant from starting). The only additional check
added in this commit is to verify the WEP key length. Similar checks for
other parameters can be added in future commits.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This workaround for Windows 7 WPS probing mechanism was previously
allowed only with hostapd, but the same interoperability issue can
happen with wpa_supplicant AP/GO mode. Allow the workaround to be
enabled in wpa_supplicant configuration for these uses.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This new configuration parameter can be used to disable automatic
offloading of scan requests to the driver which was previously used
by default if the driver supported sched_scan.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wps_vendor_ext_m1 configuration parameter can now be used to add a
vendor specific attribute into the WPS M1 message, e.g., for
Windows Vertical Pairing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A network block specific background scan period can now be configured
for drivers that implement internal background scan mechanism for
roaming and BSS selection.
Signed-hostap: Bala Shanmugam <bkamatch@qca.qualcomm.com>
p2p_pref_chan configuration parameter can now be used to set the
list of preferred channel for P2P GO Negotiation. This will be used
in the priority order if the peer does not support the channel we
are trying to use as the GO (configured operating channel or the
best 2.4 GHz/5 GHz channel) for the case where a forced channel is
not used.
p2p_pref_chan=<op class:channel>,...
For example:
p2p_pref_chan=81:1,81:2,81:3,81:4,81:5,81:6
This would configure 2.4 GHz channels 1-6 as the preferred ones with
channel 1 the most preferred option.
These configuration parameters can be set in wpa_supplicant.conf and
dynamically updated with "wpa_cli set <param> <value>".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This patch adds a configuration in network block, ap_max_inactivity, for
station's inactivity period when in AP mode. The time period is
configured in seconds, by default 300 seconds.
Signed-hostap: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
This allows Interworking network selection to be used with EAP-TLS
(client certificate/private key based credential).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This also disables WPS support if hidden SSID is enabled in AP mode.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
New global configuration parameters pcsc_reader and pcsc_pin can now be
used to initialize PC/SC reader context at start of wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
The previous elements need to be moved only if we are inserting the new
network in the middle of the list. While the memmove of zero bytes at
the end of the array does not cause real problems, some static analyzers
complain about this, so in addition to slightly optimized
implementation, this removes some analyzer warnings, too.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows credentials to be set with a specific priority to allow
the automatic network selection behavior to be controlled with user
preferences. The priority values are configured to the network block
and BSS selection will select the network based on priorities from
both pre-configured network blocks and credentials.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
New wpa_cli commands list_creds, add_cred, remove_cred, and set_cred
can now be used to manage credentials similarly to the commands used
with network blocks.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This replaces the global home_* parameters with a list of credentials
that can be configured similarly to network blocks. For example:
cred={
realm="example.com"
username="user@example.com"
password="password"
ca_cert="/etc/wpa_supplicant/ca.pem"
domain="example.com"
}
cred={
imsi="310026-000000000"
milenage="90dca4eda45b53cf0f12d7c9c3bc6a89:cb9cccc4b9258e6dca4760379fb82581:000000000123"
}
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use Domain Name List (ANQP) and the new home_domain configuration
parameter to figure out whether a network is operated by the home
service provider and if so, prefer it over networks that would
require roaming.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows HT capabilities overrides on kernels that
support these features.
MCS Rates can be disabled to force to slower speeds when using HT.
Rates cannot be forced higher.
HT can be disabled, forcing an 802.11a/b/g/n station to act like
an 802.11a/b/g station.
HT40 can be disabled.
MAX A-MSDU can be disabled.
A-MPDU Factor and A-MPDU Density can be modified.
Please note that these are suggestions to the kernel. Only mac80211
drivers will work at all. The A-MPDU Factor can only be decreased and
the A-MPDU Density can only be increased currently.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Add a new persistent group network block field, p2p_client_list, to
maintain a list of P2P Clients that have connected to a persistent
group. This allows GO of a persistent group to figure out more easily
whether re-invocation of a persistent group can be used with a specific
peer device.
Signed-hostap: Jouni Malinen <j@w1.fi>
New configuration parameters home_imsi and home_milenage can be used
to configure SIM/USIM simulator parameters for network selection based
on SIM/USIM credentials.
home_imsi=(MCC | MNC | '-' | rest of IMSI)
home_milenage=(Ki):(OPc):(SQN)
For example:
home_imsi=310026-000000000
home_milenage=90dca4eda45b53cf0f12d7c9c3bc6a89:cb9cccc4b9258e6dca4760379fb82581:000000000123
Add support for network selection for username/password credentials with
EAP-TTLS and EAP-PEAP. The new global configuration parameters
home_username, home_password, and home_ca_cert can be used to specify
credentials for network selection.
The new wpa_supplicant.conf file global parameters interworking and
hessid can be used to configure wpa_supplicant to include
Interworking element in Probe Request frames.
Replace compile-time BSS cache expiration age and scan count by config
parameters that can be set via wpa_cli and the new D-Bus API. The latter
is done with interface properties BSSExpireAge and BSSExpireCount.
This adds a new command to the interface to remove all configured
netblocks. Without this it's necessary to query properties on the
interface and explicitly remove each netblock.
Instead of converting back and forth from the string representation,
always use the binary representation internally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the network was provisioned, we need to get the keys to be able to
reconnect without new provisioning. To be able to publish those keys but
not normally configured ones, add a new attribute to struct wpa_ssid
indicating whether or not keys may be exported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The nl80211 driver can report low ACK condition (in fact it reports
complete loss right now only). Use that, along with a config option, to
disconnect stations when the data connection is not working properly,
e.g., due to the STA having went outside the range of the AP. This is
disabled by default and can be enabled with disassoc_low_ack=1 in
hostapd or wpa_supplicant configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A new configuration parameter, p2p_group_idle, can now be used to set
idle timeout value for P2P groups in seconds (0 = no timeout). If set,
this values is used to remove P2P group (both GO and P2P client)
interfaces after the group has been idle (no clients/GO seen) for the
configuration duration.
The P2P-GROUP-REMOVED event is now indicating the reason for group
removal when known. For example:
P2P-GROUP-REMOVED wlan0 GO reason=REQUESTED
P2P-GROUP-REMOVED wlan1 client reason=IDLE
This can be used to limit which frequencies are considered when
selecting a BSS. This is somewhat similar to scan_freq, but will
also affect any scan results regardless of which program triggered
the scan.
Despite comments in the wpa_config_update_prio_list(struct wpa_config
*config) telling that it is called "if priority for a network is
changed", it is apparently not.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
New global configuration parameter bss_max_count can now be used to
change the maximum BSS table size. The old fixed size limit (200) is
used as the default value for this parameter.
This adds config_methods configuration option for wpa_supplicant
following the design used in hostapd. In addition, the string is
now parsed in common code from src/wps/wps_common.c and the list
of configurable methods include all the defined methods from
WPS 1.0h spec.
The following defines are not really needed in most places, so
remove them to clean up source code and build scripts:
EAP_TLS_FUNCS
EAP_TLS_OPENSSL
EAP_TLS_GNUTLS
CONFIG_TLS_INTERNAL
In addition, start ordering header file includes to be in more
consistent order: system header files, src/utils, src/*, same
directory as the *.c file.
