Add hostapd_cli command "color_change <color>" to change BSS color at
run time. hostapd_cli status can be used to check the updated color.
Usage: hostapd_cli -i <interface> color_change <color>
If 0 value is given, HE BSS color would be disabled. Same or a non-zero
value between [1-63] can be given to enable color again.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Currently, if ACS scan request fails, states are cleared and returned.
However, in case of MLO, there is a possibilty of getting return value
of -EBUSY. In this case, ACS can retry the scan request after some time
similary to the HT40 scan.
Hence, retry the scan after 5 seconds if -EBUSY is returned. Maximum of
15 re-attempts are made before giving up.
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Co-developed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Currently, RADIUS client, auth server, and 802.1X are copied from the
first link's BSS into the non-first link during its setup. However,
there could be a case where the first link is not initialized fully
because of ACS/HT40 SCAN/DFS. Hence, in such cases, NULL is getting
copied and later it leads to segmentation fault.
Initialize those on behalf of the first link in such case and update it
so that the next time other non-first link can use it.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Add a new hostapd configuration parameter max_acceptable_idle_period to
allow the AP to accept per-STA requested BSS max idle periods.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow hostapd to be configured to not disconnect a STA if the STA fails
to reply to a group key handshake when BSS max idle period management is
used. This might be needed for some STAs that use aggressive power
saving (e.g., battery powered IoT devices).
This is disabled by default since this can delayed group rekeying
slightly and also to maintain the previous behavior. The more relaxed
operation can be enabled with the new configuration parameter
no_disconnect_on_group_keyerror=1.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow AP's behavior for BSS Max Idle Period management to be configured.
Previously, this was automatically enabled for all CONFIG_WNM_AP=y
builds. This can now be changed with the new hostapd configuration
parameter bss_max_idle:
0 = BSS Max Idle Period management disabled
1 = BSS Max Idle Period management enabled
(default and the previous behavior)
2 = BSS Max Idle Period management enabled with requirement for
protected keep-alive frames
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When AP is beaconing only on the 6 GHz band and unsol_bcast_presp
interval is set, AP sends unsolicited broadcast Probe Response frames
for in-band discovery. hostapd sent the Probe Response template for this
frame only when setting a new Beacon frame template.
Extend this to update the Probe Response template during BSS color
change.
Signed-off-by: Rathees Kumar R Chinannan <quic_rrchinan@quicinc.com>
When AP is beaconing only on the 6 GHz band and unsol_bcast_presp
interval is set, AP sends unsolicited broadcast Probe Response frames
for in-band discovery. hostapd sent the Probe Response template for this
frame only when setting a new Beacon frame template.
Extend this to update the Probe Response template during channel switch.
Signed-off-by: Rathees Kumar R Chinannan <quic_rrchinan@quicinc.com>
When AP is beaconing only on the 6 GHz band and unsol_bcast_presp
interval is set, AP sends unsolicited broadcast Probe Response frames
for in-band discovery. hostapd sent the Probe Response template for this
frame only when setting a new beacon.
As a preparation for extending this functionality to other cases, move
the generation of the unsolicited broadcast Probe Response template into
a more generic function and data structure.
Signed-off-by: Rathees Kumar R Chinannan <quic_rrchinan@quicinc.com>
If a non-PSC 6 GHz channel with bandwidth higher than 20 MHz is
configured, duplicate beacons/FD/UBPR will be transmitted in other 20
MHz channels of the current configured bandwidth to aid in faster scan.
In such cases the duplicate FD needs to carry the Operating Class and
Primary Channel subfields for non-AP STAs to identify the primary
non-PSC.
IEEE Std 802.11-2020, 9.6.7.36 (FILS Discovery frame format):
"The Operating Class subfield specifies the operating class of the
Primary Channel of the transmitting AP (see 9.4.1.36).
The Primary Channel subfield is set to the channel number of the primary
channel (see 11.15.2) if the FILS Discovery frame is transmitted as a
non-HT duplicate PPDU; otherwise, the subfield is not present."
Hence, add the Operating Class and Primary Channel subfields if the
current channel is non-PSC and the channel bandwidth is 40 MHz or
higher.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
If not set, 0 is set by default and this could fail in the following
code path when link ID is not matching:
hostapd_drv_set_ap -> wpa_driver_nl80211_set_ap -> nl80211_set_channel
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
Previously, MLO Link KDE was added only for each link that was
negotiated for the ML association. However, IEEE Std 802.11be/D5.0,
12.7.6.1 defines the MLO Link KDE to be included "for each affiliated
AP" which is not constrained by what the non-AP MLD might have requested
or what the negotiation outcome for this particular ML association is.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
There is no need to store the AP MLD's RSNE/RSNXE within per-supplicant
data structure in struct wpa_state_machine since those elements are
available from the generic authenticator data in struct
wpa_authenticator.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
There is no need to store the AP MLD's link MAC addresses within
per-supplicant data structure in struct wpa_state_machine since those
MAC addresses are available from the generic authenticator data in
struct wpa_authenticator.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
There is no need to store the AP MLD MAC address within per-supplicant
data structure in struct wpa_state_machine since that MLD MAC address is
available from the generic authenticator data in struct
wpa_authenticator.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When the RADIUS response included a Session-Timeout attribute, but is
otherwise valid (an Access-Accept with a valid Tunnel-Password), the
association still failed due to the strict comparison of the accepted
value with HOSTAPD_ACL_ACCEPT. Apparently this combination wasn't
previously tested.
Extend this to allow a packet containing a valid Session-Timeout
attribute to be accepted by extending the "success" comparison to
include HOSTAPD_ACL_ACCEPT_TIMEOUT.
Fixes: 1c3438fec4 ("RADIUS ACL/PSK check during 4-way handshake")
Signed-off-by: Lee Harding <somerandomstring@gmail.com>
Hardcoded conversion for 5 GHz band was used, but this won't work for
other cases. Set the correct center segment indexes in channel switch
fallback for non-5GHz band.
Signed-off-by: Jurijs Soloveckis <jsoloveckis@maxlinear.com>
The functions that determine the length of the RNR information and that
build the actual RNR need to use the same conditions for skipping BSSs.
Use a shared helper function for this to avoid having to maintain two
copies of the same implementation and the risking those getting out of
sync.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
RNR formation for co-location or MLO did not work as expected. Fix this.
For example, during co-location, if the BSS is also its ML partner
there is no need to include a separate TBTT for it.
Also, during co-location, if the BSS is not its partner but it is ML
capable, the TBTT length should be 16 bytes and it should include the
MLD Parameters for it in the RNR.
During co-location, for a given Neighbor AP (operating on a given
channel and op-class) if it has BSSs which are ML capable as well as
BSSs which are not, there should be two Neighbor AP Info present: one
indicating TBTT length as 13 bytes and one indicating TBTT info length
as 16 bytes.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Include link ID and partner link details in the STATUS command output
for AP MLDs.
The details would be seen as below for an AP MLD interface:
$ hostapd_cli -i wlan0 status | grep link
num_links=1
link_id=0
link_addr=AA:BB:CC:DD:EE:FF
$ hostapd_cli -i wlan1 status | grep link
num_links=2
link_id=0
link_addr=AA:BB:CC:DD:EE:FF
partner_link[1]=AA:BB:CC:DD:EE:AA
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Co-developed-by: Manish Dharanenthiran <quic_mdharane@quicinc.com>
Signed-off-by: Manish Dharanenthiran <quic_mdharane@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Whenever a BSS was set up,hostapd flushed all stations via the flush()
driver operation which maps to NL80211_CMD_DEL_STATION in the nl80211
interface. However, in case of MLO, a station could have been connected
to other links by the time this link is coming up. Since link ID was not
passed to flush(), all those stations entries were also removed in the
driver which is wrong.
Include the link ID along with the command in AP MLD so that the driver
can use this link ID and flush only the stations that use the passed
link ID as one of their links.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
This is needed for MLO group rekeying.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Co-developed-by: Adil Saeed Musthafa <quic_adilm@quicinc.com>
Signed-off-by: Adil Saeed Musthafa <quic_adilm@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Group rekeying was not supported for ML stations when non-association
link initiates a group rekey. Support this by arming the group key rekey
timer on one of the affiliated links and whenever this timer fires,
rekey group keys on all the affiliated links.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Co-developed-by: Adil Saeed Musthafa <quic_adilm@quicinc.com>
Signed-off-by: Adil Saeed Musthafa <quic_adilm@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Calculate links specific MLO GTK/IGTK/BIGTK KDE lengths based on
corresponding cipher and key instead of taking length of one link and
multiplying it by no of associated links. This is needed since the group
ciphers might be different between the affiliated links.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Co-developed-by: Adil Saeed Musthafa <quic_adilm@quicinc.com>
Signed-off-by: Adil Saeed Musthafa <quic_adilm@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
This makes it easier to extend the design for MLO group rekeying.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Co-developed-by: Adil Saeed Musthafa <quic_adilm@quicinc.com>
Signed-off-by: Adil Saeed Musthafa <quic_adilm@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Add required ML specific members in struct wpa_authenticator and struct
wpa_state_machine to maintain self and partner link information.
Maintain state machine object in all associated link stations and
destroy/remove references from the same whenever link stations are
getting removed.
Increase the wpa_group object reference count for all links in which ML
station is getting associated and release the same whenever link
stations are getting removed.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
All links were iterated over during processing ML info in Association
Request frame. However, the association link info will not be present in
the ML info and hence the following debug print is observed during ML
association (assoc link is 1):
MLD: No link match for link_id=1
Skip processing for the association link to avoid this.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Whenever there is a beacon update for any one of the affiliated link,
all the other partner links' beacon should be refreshed.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Add link ID support into EAPOL RX handler so that the events can
be routed to the appropriate link BSSs.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Add link ID support into EAPOL TX status handler so that the events can
be routed to the appropriate link BSSs.
Check each BSS's other partner link BSS STA list as well in
hostapd_find_by_sta() to support this.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
hostapd_eapol_tx_status() function is used only in drv_callbacks.c.
However, it is defined in ieee802_11.c which is not really the correct
place for it.
Hence, move the function into drv_callbacks.c and make it static.
No functionality changes.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Pass ctx in mlme_event_mgmt(). This will help in routing the event
properly to the link BSS.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
The get_hapd_bssid() function matched the given BSSID in all BSSs of its
own interface. However with MLO, there is requirement to check its own
partner BSS at least.
Compare the BSS's link partners as well and if the specified link ID
matches the link ID of the partner, return the BSS.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Modify necessary helper functions to support multiple BSS support for
MLO to make the changes scalable.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
AP MLD was added with an assumption of only a single BSS per link in the
hostapd configuration. This needs to be extended when a cohosted ML BSS
exist in the same configuration.
Extend the support for cohosted BSSs. This is required for MBSSID MLO
support as well.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Authenticator state machine ML info was set only when it was created.
However, if the association is tried again, the state machine will
already exist and hence the ML info will not be refreshed. This leads to
an issue where if in the subsequent association request, the MLD info is
different than the old info, validation of it will fail.
Fix this issue by refreshing the authenticator state machine's ML info
every time association request is handled.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
This became unused, so remove the argument from this function, all its
callers, and from places that became unused with these changes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The nl80211 driver interface function mlme_event_mgmt_tx_status(),
filled in link_id only if the frame was the last transmitted on the
whole drv (driver) level. With co-hosted MLDs, there could be cases
where multiple frames are sent out by various interfaces (BSS) under the
same drv. Now while handling the TX status, only one interface will get
the proper link_id. Rest will get -1 and the event will be routed to the
first BSS always. If the frame was not sent from the first BSS this
leads to possibility of the frame getting dropped.
Hence to make the underlying link identification easier, modify
authentication and association frames to be always sent with the link
address as A1 and A3 for ease of TX status handling.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Add support for TWT responder for AP operating in HT and VHT modes by
introducing a new configuration parameter ht_vht_twt_responder. When
this is enabled, TWT responder mode support in HT and VHT modes is
enabled if the driver supports this and is disabled otherwise.
Signed-off-by: Manaswini Paluri<quic_mpaluri@quicinc.com>
for_each_mld_link() macro used three nested for loops. Since now the
affliated links are linked together via a linked list, the logic can be
improved by using dl_list_for_each() macro instead which uses one for
loop.
Modify for_each_mld_link() macro to use dl_list_for_each() instead.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Add support for additional (vendor) elements to be added
to only Probe Response frames, for testing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If authentication fails repeatedly, e.g., because of a weak signal, the
link can end up in blocked state. If one of the nodes tries to establish
a link again before it is unblocked on the other side, it will block the
link to that other side. The same happens on the other side when it
unblocks the link. In that scenario, the link never recovers on its own.
To fix this, allow restarting authentication even if the link is in
blocked state, but don't initiate the attempt until the blocked period
is over. This reverts commit 09d96de09e ("mesh: Drop Authentication
frames from BLOCKED STA").
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes a segmentation fault on STA disconnect in case IPv6 addresses
where learned for the STA based on snooped neighbor solicication.
Fixes: bd00c4311c ("AP: Add Neighbor Discovery snooping mechanism for Proxy ARP")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
